Engineering Science and Materials Commons^™

Investigating The Behavior Of Self-Compacting Concrete Containing Scms And Recycled Fine Aggregates, Sachin Tiwari, Mahakavi P

Journal of Sustainable Construction Materials and Technologies

This study addresses the unresolved gap in quantifying how recycled fine aggregates (RFA) and metakaolin (MK) interact synergistically in self-compacting concrete (SCC), a relationship that previous works have studied only in isolation or without mechanistic justification. Twenty-five SCC mixtures containing MK (0–25%) and RFA (0–100%) were evaluated to generate a unified understanding of fresh behaviour, strength development, pore refinement, interfacial transition zone (ITZ) characteristics, and sustainability indicators. Results show that RFA alone increases water demand and reduces strength, while MK compensates for these losses by densifying the matrix and improving ITZ bonding, as confirmed through SEM analysis. An optimum synergy …

Green Roofs For Grey Water Treatment – Comparative Study Of Economic And Environmental Impacts, Shaden S. Attia

Theses and Dissertations

Cities are under more pressure than ever to use sustainable methods for managing water and other resources because of urbanization, climate change, and a lack of water. Standard greywater treatment systems (SGTSs) work well, but they use a lot of resources and don't provide a lot of ecosystem services. Greywater-treating green roofs (GTGRs) have emerged as a promising Nature-Based Solution (NBS), combining wastewater recycling with benefits like regulating temperature, reducing greenhouse gas (GHG) emissions, and reducing the urban heat island (UHI) effect. Even with this potential, there is still not enough real-world research on how GTGRs affect both the economy …

Sustainable Construction Materials In The Middle East: Model Development For Materials Selection, Taha Ahmed Omar Madu

Theses and Dissertations

The construction industry, a major driver of economic development in the Middle East, is simultaneously a leading contributor to carbon emissions, resource depletion, and environmental degradation. Amid rapid urbanization in countries such as Egypt, Saudi Arabia, and the United Arab Emirates, the adoption of sustainable construction materials has emerged as a critical strategy for mitigating environmental and societal impacts while advancing regional development objectives. This thesis is organized along two interrelated directions: first, it delivers a comprehensive assessment of the current adoption, challenges, and opportunities associated with the use of sustainable construction materials across the three target countries; second, it …

Fly Ash Proppant Developed For Hydraulic Fracturing, Raz Rzgar Haydar

Theses and Dissertations

Proppants are critical components in hydraulic fracturing, used to maintain fracture conductivity and enhance reservoir stimulation. In high-pressure and harsh reservoir environments, the use of high-strength proppants is essential to ensure well performance. Conventional proppants, being sand, ceramic, and sintered bauxite can be expensive, and their use often requires costly fracture fluids. This study investigates the possibility of utalizing fly ash geopolymers as a sustainable alternative that is also cost-effective for proppants manufacturing. Fly ash, a by-product from the combustion of coal and other materials, was explored as a base material for proppants, utilizing an alkaline solution as an activator …

Thermal Transformations And Mechanical Properties Of All-D-Metal Mn2fecu Heusler-Type Shape Memory Alloy, Choji J. Daches, Joseph W. Newkirk, Mario Buchely

Materials Science and Engineering Faculty Research & Creative Works

All-d-metal Heusler alloys are emerging functional materials in which magnetic ordering, lattice distortion, and mechanical behavior are strongly coupled through d–d electronic interactions. This study systematically investigates the structural, thermal, magnetic, and mechanical properties of Mn₂FeCu synthesized within a Heusler-type compositional framework. SEM/EDS revealed a dual-phase FCC-based microstructure consisting of Mn–Fe–rich and Mn–Cu–rich domains, while XRD confirmed FCC symmetry with compositional partitioning rather than full L2₁ ordering. Differential scanning calorimetry identified partial melting of the Cu-rich phase near ~ 900 °C. Dilatometry showed a thermoelastic FCC → FCT transformation at ~ 770–780 °C with a recoverable strain of ~ 0.067%. …

The Effects Of Mold Flux Contamination On Oxide Scale Formation And Hydro-Descaling Efficiency During Steel Processing, Tochukwu Princewill Ojiako, Richard Osei, Mario Buchely, Haiming Wen, Simon Lekakh, Ronald O'Malley

Materials Science and Engineering Faculty Research & Creative Works

Oxide scale formation during thin-slab continuous casting has a complex structure, which is influenced by mold flux contamination, that modifies interfacial reactions during solidification, subsequent reheating, and descaling. While individual aspects of the oxidation behavior of carbon steel have been previously examined, the synergetic effects of mold flux contamination during continuous casting and subsequent reheating on scale modification and the efficiency of hydraulic descaling remain inadequately studied. This study quantitatively examines the effect of flux composition on oxide scale evolution, adhesion, and hydraulic removal in low-carbon steel under simulated industrial conditions. Slab samples with as-cast, cleaned, and flux-coated surfaces were …

Discrete Element Modeling Of Granular Soils: Critical State Behavior Applied To Impact Pile Driving, Esteban Patino Marin

Graduate Studies Theses and Dissertations 2026

This thesis investigates the use of the Discrete Element Method (DEM) to study two complementary aspects of granular soil mechanics: critical state behavior of granular materials and dynamic response of driven piles in sand, both of which are governed by the same particle-scale mechanisms of dilation, contraction, and fabric evolution.

The first examines the critical state behavior and fabric anisotropy of granular soils through DEM simulations of direct shear, direct simple shear, and true triaxial tests. Sphere-cluster particles representative of a uniform sand are used in two assemblages of approximately twenty-five thousand and one hundred twenty-five thousand spheres to evaluate …

Modeling Of Transformation Temperatures In Cast Martensitic Stainless Steels-Ca6nm: Effects Of Composition, Heating Rate, And Grain Size, Ugochukwu Agbedo, Mario Buchely, Laura Bartlett, Caelan Kennedy

Materials Science and Engineering Faculty Research & Creative Works

Accurate prediction of the critical transformation temperatures Ac1 and Ac3 is one of the essential factors in the heat treatment of CA6NM cast martensitic stainless steel. In this study, the influence of alloy composition, heating rate, and prior austenite grain size on the critical temperatures was quantified using dilatometric measurements and statistical modeling. Six heat treatment conditions produced prior austenite grain sizes ranging from ~75 to 247 µm. Experimental results showed that grain size variations produced only minor changes in Ac1 and Ac3, indicating a weak dependence of transformation temperatures on prior austenite grain size within the investigated range. In …

Multiphysics Simulation And Experimental Validation Of Phase Transformation And Hardness In Jominy End-Quenched Low-Alloy Steels, J. S. Alabi, E. Heidari, M. F. Buchely, K. Chandrashekhara, S. N. Lekakh, R. J. O'Malley, V. A. Athavale, A. Kumar

Materials Science and Engineering Faculty Research & Creative Works

High-volume industrial continuous hot-rolled steel heat treatment processes involve sophisticated multi-phase modeling. The performance of a given process can be optimized by coupling phase transformation kinetics with the cooling conditions of the process. This study develops a multiphysics model to simulate an intensive quenching process for steel, which is inherently transient and highly dependent on numerous parameters. The simulated object was a Jominy end-quenched specimen geometry using two commercial steels, AISI 4130 and AISI 4140, with the goal of transferring a verified methodology to the heat treatment process for industrial heavy-section products (bars, slabs). The simulation employs thermal, mechanical, and …

Critical Parameters Controlling Oxide Scale Formation And Hydro-Descaling Efficiency During Steelmaking, Tochukwu Princewill Ojiako

Doctoral Dissertations

In modern steelmaking, cast slabs are exposed to high-temperature oxidizing environments during secondary cooling, reheating, and hot rolling, resulting in the formation of multilayer oxide scales on the steel surface. These scales interact with mold-flux residues originating from the casting process (CC). The morphology, chemistry, and adhesion of oxide scale strongly influence its removability during high-pressure hydraulic descaling and ultimately determine the surface quality of hot-rolled products. However, the mechanistic relationship between oxide scale evolution, scale-steel interfacial structure, and hydraulic descaling performance remains poorly understood.

This dissertation investigates oxide scale formation, modification, and removal in low-carbon thin-slab steels produced by …

Castrip Process Technology: Non-Grain Oriented (Ngo) Si Steels Extension And Carbide-Free Bainitic (Cfb) For Flat Products, Naram Naidu Meesala

Masters Theses

"This research explores the development of advanced steel grades manufactured through Castrip® twin-roll thin strip casting technology, with particular attention to non-grain-oriented electrical Si-Steels (NGOES) and carbide-free bainitic (CFB) steels. The Castrip® process offers a near-net-shape route for producing thin steel strips, which greatly decreases the number of processing stages, lowers energy demand, and reduces carbon dioxide emissions when compared with traditional steel production methods.

In the NGOES part of the study, several industrial Fe–Si steel compositions were cold rolled to final thicknesses ranging from 0.35 mm to 0.15 mm. These materials were then exposed to short-duration continuous annealing at …

Process Optimization And Quality Control In Manufacturing Of Frp Composites By Vartm, Mohamed Emadeldin Omar Abdelhadi

Graduate Theses, Dissertations, and Problem Reports (ETD)

Railroad tank cars, being one of the most used means of transportation of hazardous material across the country, have not been structurally upgraded for a long time. Thus, the Pipeline and Hazardous Materials Safety Administration (PHMSA), a United States Department of Transportation (USDOT) agency, released a rule for safer transportation of highly hazardous and flammable liquids by railroad to enhance the design specifications of both the new and existing tank cars in May 2015. A multifunctional composite jacket is proposed as a new material to structurally enhance the railroad tank cars to withstand any accidents that could happen en route. …

Curing Duration Optimization To Reduce Shrinkage Cracking In One-Part Alkali-Activated Slag Concrete, A. Sadrmomtazi, H. Zanganeh

Journal of Sustainable Construction Materials and Technologies

The consequences of inadequate curing on one-part alkali-activated slag concrete (O-AAS) performance relative to ordinary Portland cement concrete (OPCC) have been investigated in this research. Prior to exposure to unsaturated conditions, samples underwent initial moist curing for durations ranging from 24 hours to one year. The testing program included compressive strength evaluation, chloride ion transport analysis, and measurement of free and restrained shrinkage. In addition, cylindrical cores were extracted from concrete columns to assess internal strength and chloride penetration resistance. Under unsaturated exposure, O-AAS exhibited a strength-aging phenomenon, with up to a 37% decrease in compressive strength over 360 days, …

Laboratory Investigation And Numerical Modelling Effect Of Carbon Nanotubes On Hot Mix Asphalt Permanent Displacement, Sepehr Saedi, Auwal Usman Nadada

Journal of Sustainable Construction Materials and Technologies

One of the primary causes of asphalt pavement deterioration is rutting; in contrast, one of the most effective methods to address this type of damage is the use of additives and quality evaluation during the design stages. In this research, laboratory testing and modeling using Abaqus software were employed to validate the laboratory results and predict and assess the potential for rutting. Carbon nanotubes (CNTs) were selected as an additive due to their exceptional mechanical properties and molecular interactions with bitumen. These nanotubes were used to modify the bitumen for the preparation of laboratory samples. The laboratory results from the …

Influence Of Early Microwave Curing On Performance Of Slag-Based Geopolymer Mortars, Ahmet Taşdemı̇R, Abdulkadir Çevı̇K

Journal of Sustainable Construction Materials and Technologies

In this article, an experimental study was conducted to examine the effect of curing time and microwave power on the compressive strength of early microwave-cured slag based geopolymers. Geopolymers have the potential to serve as an environmentally friendly substitute for cement-based building materials, and the use of microwave curing to geopolymers holds the promise of substantial strength improvement. Different microwave curing energies (300 - 800 Watts) were utilized at varying durations (10 - 60 minutes) on demoulded mortar specimens after one day. After that, compressive strength tests were conducted on both the cured and uncured specimens at three different ages: …

Use Of Alaçatı Stone Aggregate In Conventional And Self-Consolidating Concretes, Tahir Kemal Erdem

Journal of Sustainable Construction Materials and Technologies

Alaçatı stone or Alapietra stone is widely used mostly for building cladding. However, its production and use in the construction sites generate high amounts of waste (debris), causing environmental pollution in Çeşme which is a touristic district. This study investigated the reuse of Alaçatı stone as lightweight aggregate (LWA) in both conventional and self-consolidating concrete (SCC) mixtures. The concretes were prepared to have three different water-to-cement ratios (w/c), which were 0.38, 0.42 and 0.48. For each w/c, a conventional concrete mixture and two SCC mixtures with 60 or 70 cm slump flow were produced by varying the superplasticizer SP content. …

A Decision Support Model For Building Material And Component Reuse In The Context Of Circular Buildings, Havva Aksel

Journal of Sustainable Construction Materials and Technologies

Construction activities cause significant environmental impacts such as waste generation, pollution, resource consumption, and land use, which are expected to increase with global construction demands. To mitigate these environmental problems, the circular building occurs as an emerging concept depending on in the circular economy, which aims to minimize waste and redefine the “end-of-life” concept by reducing, reusing, recycling, and recovering materials. The reuse of building materials and components (BMCs) from existing structures represents a crucial strategy for achieving circularity in the built environment. Within this framework, design plays a key role. However, designing with reclaimed BMCs remains complex due to …

Durability Of Alkali-Activated Concretes Under 5% Sulfuric Acid Environment, Celal Karabaş, Anıl Niş

Journal of Sustainable Construction Materials and Technologies

The investigation focused on the resistance to 5% sulfuric acid degradation of the alkali-activated concretes (AAC). The AAC was manufactured using a blended binder of 50% slag and 50% F-type fly ash. The AAC was activated using a blend of 14 M sodium hydroxide and sodium silicate, with a hydroxide-to-silicate ratio of 1/2,5. Six AAC were produced against a 5% sulfuric acid environment, varying the binder amounts (400–500–600 kg/m3) and activator-binder (A/B) ratios (0,45–0,55). The chemical resistance of AAC was evaluated by visual appearance, variation in weight and compressive strengths. The findings pointed out that more gypsum and higher weight …

Comprehensive Risk Assessment For Construction Site Managers In Kosovo: A Mixed-Method Approach, Muhamet Ahmeti, Besian Sinani

Journal of Sustainable Construction Materials and Technologies

This study developed and validated a hybrid ISO 31000:2018 Kosovo-compliant risk assessment framework tailored for construction site managers operating within transitional economies. The research employed audits of 20 ISO-certified contractors in Pristina, Kosovo, along with field observations, interviews, and quantitative risk matrices. The findings indicate a critical concentration of risk, with 70% of firms classified as "High" or “Very High” risk. The most prevalent hazards identified were working at height without collective protection, unprotected electrical systems, and manual handling of heavy materials. Regression analysis revealed that firms with a designated safety champion achieved significantly lower risk scores, whereas those with …

Behaviour Of Internally Strengthening Hollow Stainless-Steel Hot-Rolled Circular Columns Filled With Crumb Rubber And Recycled Aggregate Concrete, Wadhah M. Tawfeeq, Mohammed M. Rasheed, Mithaq Kohees, Ahmed W. Al Zandd, Saif Al-Balushi, Hamed Al Abdul Salam

Journal of Sustainable Construction Materials and Technologies

Stainless-steel sections are increasingly being utilised in favour of their higher durability. Simultaneously, the use of recycled materials in concrete is aligned with the global concern to encourage sustainable and environmentally friendly construction. The paper examined the behaviour of stainless-steel columns filled with concrete with crumb rubber (CR) and recycled aggregate (RA). It analysed the effect of different percentages of CR (0, 15, and 30) and RA (0, 15, and 50) on the compressive strength of the concrete and the performance of the columns using stainless-steel hollow sections. 20 specimens were manufactured, 18 of which were cast with concrete containing …

Piezoelectric Concrete: A Smart Material Approach For Energy-Harvesting Structural Technologies, Dianah Mazlan, Vynotdni Rathinasamy, Naveen Kumar, Liu Chunpeng, Elango Elango

Journal of Sustainable Construction Materials and Technologies

The rapid growth of urban infrastructure demands innovative materials that not only support structural performance but also contribute to sustainability through energy harvesting. Piezoelectric concrete, which integrates ceramics, polymers, nanomaterials, and bio-based fillers into cementitious matrices, has emerged as a promising solution. This review systematically explores the fundamentals of piezoelectricity in concrete, highlighting how stress-induced electromechanical coupling enables both energy harvesting and structural health monitoring. The paper critically evaluates major material systems including PZT ceramics, PVDF polymers, hybrid nanocomposites, and emerging bio-based materials, alongside their integration strategies such as embedded and surface-mounted approaches. Applications across pavements, bridges, and smart buildings …

Scientific Characterization Of Historic Mortars Dating From The 15th-Century Of A Historical Building In Algeria: A Case Study, M. E. Belgacem, N. Rabahi-Touloum, R. Neves, Y. Ouldkhaoua

Journal of Sustainable Construction Materials and Technologies

This research investigates the historic mortars (Aggregate/Binder (A/B) ratio) of a historical patrimony building, dating from the 15th century, in Algeria, for restoration purposes. It is well known that thorough characterization is essential for successful restoration. To this end, several techniques, including Scanning Electron Microscopy (SEM), X-ray Diffraction (XRD), and X-ray Fluorescence (XRF), optical microscope were used to characterize the historic mortars. A mechanical test was used to characterize the compressive strength of a historic mortar. For a comprehensive characterization, A/B ratios were estimated using both Digital Image Analyses (DIA) and chemical analyses. The results obtained provided clear information on …

Nonlinear Analytical Models Of The Seismically Isolated ``Frame-Boiler'' System With Cantilever-Type Hysteresis Dampers, Aleksandr Mikhailovich Anushchenko, Dmitrii Evgenievich Bondarev, Aleksandr Yurievich Schukin

Journal of Sustainable Construction Materials and Technologies

This study shows results of development of the ``frame-boiler'' system with hysteresis dampers analytical model. Hysteresis dampers are used as boiler antiseismic bracing. It is noted that simplified analytical models are necessary at the stage of preliminary iterative calculations, when a CAE-modeling is impractical due to significant time costs. The authors have proposed 2 options of analytical models: 2-mass model and 3-mass model. The differential equations of motion for each model are written below. The results of the calculation for seismic impacts are compared with the finite element model. It is shown that 3-mass model gives good match of results …

Advancing Sustainable Structural Solutions: Hemp Fiber-Reinforced Polymer (Hfrp) Reinforcement Bars For Concrete Applications Through Material Selection, Simulation, And Pathways For Future Development, Thomas Cadenazzi, Busra Keles

Journal of Sustainable Construction Materials and Technologies

This paper investigates innovative Hemp Fiber-Reinforced Polymer (HFRP) rebars as a sustainable alternative to conventional Carbon Steel (CS) and Glass Fiber-Reinforced Polymer (GFRP) rebars used as reinforcement in concrete structures. The feasibility of HFRP rebars is assessed, focusing on mechanical properties and sustainability advantages. A virtual tensile test on a modeled M19 HFRP rebar, conducted using Autodesk's Fusion 360, demonstrates tensile strength comparable to CS 235 and greater environmental sustainability than GFRP, despite a slight reduction in stiffness. The study also considers the potential of graphene fiber integration to enhance mechanical properties, underscoring HFRP's adaptability. Findings suggest that HFRP rebars, …

Comparative Analysis Of Life Cycle Assessment Of Traditional And Contemporary Timber Buildings, Sadık Akşar, Gökçe Tuna

Journal of Sustainable Construction Materials and Technologies

Wood has long been used as a primary building material, but with the Industrial Revolution and the spread of multi-story structures, its structural limitations became evident. In the 21st century, engineered timber products have reintroduced wood as a sustainable alternative, offering advantages such as lightness, rapid assembly, and recyclability. At the same time, buildings are responsible for significant environmental impacts, making assessment methods essential. Life Cycle Assessment (LCA) is one of the most widely used tools for evaluating these impacts across all stages of a building’s life cycle. This study applies LCA to timber construction systems, focusing on both traditional …

Sustainable Paving Block Development: Utilizing Rejected Coal As Filler And Assessing Its Impact On Paving Block’S Properties, Siti Nikmatin, Allen Kurniawan, Heriansyah Putra, Rima Fitria Adiati, Riawan Ma’Ruf, Dwi Arso Yedi Irwanto

Journal of Sustainable Construction Materials and Technologies

This study investigated the potential use of rejected coal as a fine aggregate filler in paving block production. Comprehensive characterization of the rejected coal was conducted, including toxicity, physical, chemical, and mineralogical analyses of the coal. The results showed that the rejected coal met environmental safety standards (TCLP) and had suitable properties as an aggregate. Paving blocks were produced by incorporating different proportions of rejected coal fillers and were tested for compressive strength, water absorption, and density. The optimal mix with 35% rejected coal filler as a replacement of stone ash achieved a compressive strength of 14.61 MPa, water absorption …

Numerical Comparative Study Of The Thermal Performance And Load-Bearing Capacity Of Hollow Clay Bricks Used In Construction In Libya, Osama Lawej, Mahmoud Ahmed, Ismael Ehtiwesh

Journal of Sustainable Construction Materials and Technologies

The optimization of structural and thermal performance in building components is a key challenge in sustainable construction, particularly in hot climate regions like Libya. Hollow clay bricks are widely used due to their local availability and affordability; however, their internal geometry is often not optimized for thermal resistance or mechanical integrity. This study addresses this gap by numerically investigating the effect of cavity geometry on the load-bearing capacity and thermal insulation performance of hollow clay bricks. Three configurations were analyzed, including two commercial designs from the Libyan market and a newly proposed arched cavity design. Finite Element Method (FEM) simulations …

Developing A Modular Circular Wall Over-Clad System For Facade Thermal Upgrade In Deep Energy Retrofit, Patrick Daly

Journal of Sustainable Construction Materials and Technologies

The EU has implemented several policy and legislative initiatives aimed at decarbonisation and circularity transition of the Built Environment including a strategy for large scale renovation of the building / housing stock. Modularised construction solutions are argued to be a potential acceleration pathway toward this objective. Yet there remains issues and challenges in implementing such strategies in a complex and heterogeneous stock and sector. This research investigates this decarbonisation pathway, examining the feasibility and potential of applying a modularised construction over-clad system, based on advanced circularity, in the deep energy retrofit of social housing. The research is based on a …

Experimental And Numerical Investigation On The Effect Of Projectile Mass And Apex Angle On Penetration Depth Into Sandy Soils, Abdul-Rahman K. Osman, Ahmed Elshesheny Dr, Mohamed S. Zahran Dr, Nabil M. Nagy Prof.

Journal of Engineering Research

Projectile penetration in granular soils remains a critical concern in defense engineering and ballistics research. This study presents an experimental and numerical investigation of rigid cone-tip projectile penetration into very dense sand, examining the influence of apex angle and projectile weight on penetration depth. Laboratory experiments were conducted using metallic projectiles with apex angles of 10°, 30°, 60°, and 90° and weights of 2.445, 3.87, 5.33, and 6.81 kg, dropped from a height of 4.295 m into a 500×500×500 mm wooden tank filled with sand to 400 mm height at 95% relative density. Through systematic testing, two empirical correlation …

Detection Of Bacterial Genomic Dna Fragments Using The Mxene Crispr-Cas9 Field-Effect Transistor, Jiaoli Li, Ali Taheri, Weijia Liu, Ying Zhuo, Pengfei Ma, Chenglin Wu

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Clustered regularly interspaced short palindromic repeats (CRISPR)-based field-effect transistor (FET) sensors provide a promising platform for highly specific and amplification-free nucleic acid detection. However, their direct application in identifying target sequences within intact genomic DNA remains underexplored. We developed a CRISPR-Cas9 FET sensor for detecting DNA sequences by immobilizing Cas9 onto a graphene-MXene sensing interface via (3-aminopropyl)triethoxysilane (APTES) functionalization. The sensor targeted Stx1, a 440 bp laboratory-amplified fragment associated with Shiga toxin production in pathogenic E. coli. Gel electrophoresis confirmed the precise cleavage of Stx1, while the nontarget sequence Stx2 remained undetected. FET measurements further validated the sensor's specificity, showing …