Systems and Communications Commons^™

Thermal Evolution Of Moon, Arshdeep Singh Gill

Master's Theses

In August, 2014 three experiments were conducted using infrared systems deployed at White Mountain Research center, CA. The data was acquired for the whole month of August. Teams of 3-4 students from Cal Poly San Luis Obispo and UC Santa Barbara were stationed at the research center for 2-3 days to operate the equipment. The three experiments were:(1) creating spatial-temporal time series of lunar surface temperatures;(2) identifying atmospheric meteor trails;(3) search for meteor impacts on the Moon surface. Out of the three this thesis focusses on experiment 1 and the results from this experiment could also help with the other …

Scaled Synthetic Aperture Rader Development, Jason Garvey Schray

Master's Theses

Several previous Cal Poly thesis projects involve synthetic aperture radar (SAR), automatic target recognition (ATR), and tracking. SAR data was either accessed from a publicly available database or generated using complex computer modeling software. The motivation for this dual thesis project is to design and construct a scaled SAR system to support Cal Poly radar projects. Ideally this is a low-cost, high resolution SAR architecture that produces raw range Doppler data for any desired target area. To that end, a scaled SAR system was successfully designed, built, and tested. The current SAR system, however, does not perform azimuthal compression and …

Wireless Mesh Networks For Scada Systems, Zachary Weisman

Computer Engineering

No abstract provided.

Prosense, Johnny Favazza Ii, Casey Glasgow, Matt Epperson

Computer Engineering

This project aims to gather advanced data sets from MEMS sensors and GPS and deliver it to the user, who can capitalize on the data. The once negligible half-degree difference of your board barreling down a wave can be recorded from a gyro and exploited for the perfect turn. The exact speed dreaded by longboarders where speed wobbles turn into a road rash can be analysed and consequently avoided. Ascertaining the summit of your flight using combined GPS sensors from the ski ramp allows for the correct timing of tricks. When it comes to pursuing excellence in professional sports, amateur …

Pinpoint: Location Beacon And Tracking, Ezequiel Lopez Iii

Computer Engineering

The purpose of Pinpoint was to create a device that can collect and transmit location information for multiple users on a wireless network. The device would be used to keep track of and communicate with other users nearby. The final design includes a touchscreen display as a graphical user interface (GUI), an XBee RF module for wireless networking, a GPS receiver for location tracking, and a Programmable System on a Chip (PSoC) to control the modules.

Underwater Optical Wireless Audio Transceiver, Angel Ayala

Electrical Engineering

Scuba diving carries risks that can endanger lives. Many of these risks are preventable. However, an underwater communication system can increase a diver’s safety. Along with providing safety, an underwater communication device can enhance the scuba diver’s enjoyment.

A low cost underwater optical wireless audio transceiver is designed. The project consists of the off-the-shelf parts that uses a microphone and speaker to transmit and receive sound. The project uses the concepts of visible light communications and pulse width modulation to transmit and receive sound. Although sound is commonly transmitted through ultrasound methods, visible light communications has several advantages. Visible light …

Analysis Of Various Algorithmic Approaches To Software-Based 1200 Baud Audio Frequency Shift Keying Demodulation For Aprs, Robert F. Campbell

Master's Theses

Digital communications continues to be a relevant Field of study as new technologies appear and old methodologies get revisited or renovated. The goal of this research is to look into the old digital communication scheme of Bell 202 [67] used by APRS and improve software based demodulation performance. Improved performance is defined by being able to correctly decode more packets in an efficient, real time, manner. Most APRS demodulation is currently done using specialized hardware since that yields the best performance. This research shows that through using Sivan Toledo's javAX25 [72] software package, new demodulation algorithms can be implemented that …

Real-Time Digital Effects Processing Using Ios, Jonah W. Clinard

Computer Engineering

In today’s society, we are seeing incredible improvements in terms of creating smaller technological devices that behave more and more like the personal computers of yesterday. Mobile “Smart” devices, in particular, are becoming incredibly powerful not just in terms of processing power, but in the fact that they are able to provide assistance to users in their everyday lives. Application developers are now able utilize the power and size of these devices, to create and realize ideas that would have been previously viewed as impossible. This project applies the fields of digital signal processing, music, and mobile application development, to …

Scaled Synthetic Aperture Radar System Development, Ryan K. Green

Master's Theses

Synthetic Aperture Radar (SAR) systems generate two dimensional images of a target area using RF energy as opposed to light waves used by cameras. When cloud cover or other optical obstructions prevent camera imaging over a target area, SAR can be substituted to generate high resolution images. Linear frequency modulated signals are transmitted and received while a moving imaging platform traverses a target area to develop high resolution images through modern digital signal processing (DSP) techniques. The motivation for this joint thesis project is to design and construct a scaled SAR system to support Cal Poly radar projects. Objectives include …

Universal Uav Payload Interface, Nolan Reker, David Troy Jr, Drew Troxell

Computer Engineering

Unmanned Aerial Vehicle (UAV) technology is becoming increasingly accessible for civilian use. Both open-source and commercial-purpose UAVs can be obtained affordably or even built. However, the platforms available are very segmented in their customization to a specific application (i.e. land surveying, payload delivery). This project aims to create a Universal Payload Interface (UPI) mounted to the underside of multi-rotors or other UAVs to enable the attachment of customizable sensor payloads. These payloads allow a single UAV to be rapidly reconfigured to perform a multitude of tasks.

The Universal Payload Interface facilitates communication between the payload, onboard flight controller, and operator …

The Electric Reel For Soccer Fields, Stephen Taylor

Electrical Engineering

Painting a soccer field consumes too much time. The process of reeling the string after laying out string along the field needs to improve. As a result, my project addresses improvements in how the workers retrieve the string through the production of an electric reel. This electric reel allows the worker to have control of the speed, direction, and on/off state of the device. Direction control allows the user ability to reel and unwind the string. Variable speed allows the user to control how fast the reel unwinds and reels the string. The device gathers string in an orderly manner …

Uav Avoidance System, Zachary Stargensky

Electrical Engineering

This is an ongoing design project being funded by Northrop Grumman in which Cal Poly SLO is working in collaboration with Cal Poly Pomona to complete a working design at the end of each academic school year. The project consists of two UAVs that can navigate around a given area without running into each other or other obstacles. There are sensors to be mounted on the vehicles that can detect objects within a given distance and a microcontroller is used to control how the vehicle responds to an object being detected. The avoidance code has been written for previous years’ …

Design And Fabrication Techniques Of Devices For Embedded Power Active Contact Lens, Errol Heradio Leon

Master's Theses

This thesis designed and fabricated various devices that were interfaced to an IC for an active contact lens that notifies the user of an event by detection of an external wireless signal. The contact lens consisted of an embedded antenna providing communication with a 2.4GHz system, as well as inductive charging at an operating frequency of 13.56 MHz. The lens utilized a CBC005 5µAh thin film battery by Cymbet and a manufactured graphene super capacitor as a power source. The custom integrated circuit (IC) was designed using the On Semiconductor CMOS C5 0.6 µm process to manage …

Synthetic Aperture Radar: Rapid Detection Of Target Motion In Matlab, Daniel S. Kassen

Master's Theses

Synthetic Aperture Radar (SAR) has come into widespread use in several civilian and military applications. The focus of this paper is the military application of imaging point targets captured by an airborne SAR platform. Using the traditional SAR method of determining target motion by analyzing the difference between subsequent images takes a relatively large amount of processing resources. Using methods in this thesis, target motion can be estimated before even a single image is obtained, reducing the amount of time and power used by a significantly large amount. This thesis builds on work done by Brain Zaharri and David So. …

Hybrid Silicon Mode-Locked Laser With Improved Rf Power By Impedance Matching, Bassem M. Tossoun

Master's Theses

The mode-locked laser diode (MLLD) finds a lot of use in applications such as ultra high-speed data processing and sampling, large-capacity optical fiber communications based on optical time-division multiplexing (OTDM) systems. Integrating mode-locked lasers on silicon makes way for highly integrated silicon based photonic communication devices. The mode-locked laser being used in this thesis was built with Hybrid Silicon technology. This technology, developed by UC Santa Barbara in 2006, introduced the idea of wafer bonding a crystalline III- V layer to a Silicon-on-insulator (SOI) substrate, making integrated lasers in silicon chips possible.

Furthermore, all mode-locked lasers produce phase noise, which …

Rapid Battery Exchange Safety And Sensing, Ben John Froelich, Isaac Sungjin Kim

Electrical Engineering

The Rapid Battery Exchange system (RBX) swaps batteries in an electric van, allowing almost continuous operation of the vehicle. The RBX system is designed and built by The Cal Poly Electric Vehicle Engineering Club (EVEC). The system includes the exchange ramp, two battery packs, and the electric “G-Van.” While the vehicle drives using one of the battery packs, the other pack charges in the exchange ramp. When the van’s battery depletes, it drives onto the ramp and swaps the dead battery for the charged one, and the process repeats.

The RBX battery pack safety and sensing project divides into two …

Design Improvement For The Smart Dc Wall Plug, Cory Yee, Haoyan Huang

Electrical Engineering

The DC smart wall plug is a subsystem within the Cal Poly DC House Project. The previous version faces challenges supplying DC voltage to meet household appliances’ nominal values. Specifically, it can only output the minimum required voltage for DC appliances to operate, resulting in unwanted power loss. In addition, the maximum output voltage is rated at 15V, which is insufficient to power most DC appliances. This design improvement project incorporates NFC technology as a solution to overcome the power loss and a new buck converter configuration to increase the output voltage range. Additionally, the new design introduces short-circuit and …

Cnc Torch, Steven Chiu

Computer Engineering

This CNC Torch cuts steel plate. It can cut up to a maximum area of 3x3 feet. The user builds a cut list on the touchscreen from a selection of predefined shapes and enters the parameters need for each shape. When the user is ready, the cut list is sent to an Arduino that will move each motors accordingly to the shapes desired.

Data Chunking In Quasi-Synchronous Ds-Cdma, Trevor Dalke

Master's Theses

DS-CDMA is a popular multiple access technique used in many mobile networks to efficiently share channel resources between users in a cell. Synchronization between users maximizes the user capacity of these systems. However, it is difficult to perfectly synchronize users in the reverse link due to the geographic diversity of mobile users in the cell. As a result, most commercial DS-CDMA networks utilize an asynchronous reverse link resulting in a reduced user capacity. A possible compromise to increase the user capacity in the reverse link is to implement a quasi-synchronous timing scheme, a timing scheme in which users are allowed …

A Compact, Reconfigurable Uhf Communication System Design For Use With Polysat's Embedded Linux Platform, Austin Williams

Master's Theses

The beginning of this thesis provides an overview of the heritage UHF Communication System design flown on CP2, CP3, CP4, CP5, and CP6, summarizing previous analysis of its performance, and providing the justification for a complete system re-design. High level requirements for the new UHF System are defined, and a trade study is performed on state-of-the-art single chip transceivers, low noise amplifiers, and transmit power amplifiers. These components are then designed into a functional communication system, with key components analyzed for proper impedance matching and performance characterization compared to expected datasheet values. Next, the system as a whole is characterized …

Pier Portal Project Ii, Andy Lam, Brian Markwart

Computer Engineering

The goal of this project is to design and build a remotely controllable camera system that will be deployed at the Cal Poly Pier located in Avila Beach. The system is composed of a camera and all of its lighting and movement controlling hardware enclosed into a waterproof acrylic tube, allowing it to be lowered underwater. The camera will stream its video feed onto a website where any user will be able to watch a live video stream from the pod. In addition, users with the correct privileges will be able to remotely control of the camera system via the …

Eco Sensor Pod, Austin Zuffi, Michael Chamoures

Computer Engineering

The EcoSensor Pod, designed by the UCSD Data Turbine group, is a self-contained hardware/software solution for environmental monitoring, disaster response, and other real-time sensing applications. We improved upon the design of the Sensor Pod by 1. Developing a custom PCB for the system to remove the problem of wires becoming de-attached in harsh environment deployments and 2. Creating an easy-to-use web application that provides the UCSD team with the ability to view various charts displaying both past and live, real-time data. These modifications were successfully implemented and tested and will make future deployments of the EcoSensor Pod more robust and …

Design Of An Energy Efficient Virtual End Node Client Using Openadr2.0a And Smap, Kevin Navero

BioResource and Agricultural Engineering

Demand Response (DR) describes the set of actions taken to impose a reduction in electrical loads to stabilize the power grid and decrease costs. It is used when power grid emergencies or extremely high demand and congestion, threaten the electricity supply-demand balance. Automated Demand Response (ADR) describes a web-based control system that triggers DR events automatically by signaling other pre-programmed control systems. This project intends to use the OpenADR2.0 specifications provided by the OpenADR Alliance to construct an open source Virtual End Node (VEN) client to retrieve DR signals. The Simple Measurement and Actuation Profile (sMAP) software is also used …

Practical Irrigation Scheduling Program, Dominic Sween

BioResource and Agricultural Engineering

This senior project discusses the design, construction, and evaluation of an irrigation scheduling program that aids users in alfalfa irrigation management, with the potential for application with other crops. The program uses a very accurate irrigation prediction model that forecasts what the estimated irrigation need of each week will be, as well as the number of irrigations needed to satisfy the requirement. The model was found to predict the sum of the actual required weekly irrigation amount within less than 1% of the true value. The program was based off the single crop coefficient approach that was outlined previously by …

Buddy: A Breathalyzer For Iphone, Douglas Blaalid, Brandon Bevans

Electrical Engineering

Buddy is a Breathalyzer for the iPhone designed to be more a product than a project. Through proprietary hardware and a custom iOS application, Buddy provides users with a previously untapped link from the alcohol in their body to the display on their phones. Buddy uses an alcohol sensor connected to an Arduino Uno to accurately detect the BAC of the user’s breath. The BAC is then transmitted to an iPhone via the headphone jack where it is displayed and logged in a captivating app. The finished prototype successfully measured the approximate BAC of intoxicated users. The product website has …

High Frequency Open Air Optical Communication System, Alexander C. Wolff

Electrical Engineering

The goal of this project is to create a wireless optical communication system that operates at high frequencies (up to 3 GHz). The system will function by taking a digital electric input signal, converting it to a photonic signal, recovering the signal at the other end of a short distance (~1 foot) and converting it back into a digital signal. Unlike the more common fiber-optic data transmission systems, this system will transmit light through air, instead of fiber, as its medium. Doing so will have the benefits of a wireless system combined with the benefits from an optical system, including …

A Novel Unit Cell Antenna For Highly Integrated Phased Arrays In The Shf Band, Timothy Bryan Ogilvie

Master's Theses

Phased arrays are electromagnetic antenna systems comprised of many radiating elements and processing electronics. Radiating elements are typically positioned in an orderly grid within the antenna aperture. In the receive mode of operation, radiating elements capture some of the signal energy from incoming radiation and guide these signals to processing electronics. Signals are filtered and amplified to maintain the desired sensitivity and complexly weighted using circuits with reconfigurable amplification gain and phase delay. Finally, all signals are combined. The summation of these complexly weighted spatial samples forms a spatial filter in the same way complexly weighted temporal samples establish a …

Radio Link Analysis And Characterization Of Past And Future Cal Poly Cubesats, Brian Gilbert Tubb

Electrical Engineering

Cal Poly's satellites design team, PolySat, has three satellites in Low Earth Orbit (LEO) and four more planned to launch within the next two years. Radio communication of past and current orbiting satellites has been an exercise in frustration, prompting significant research into the satellite-side of the radio link by several other Senior Projects and Thesis papers. However, minimal effort has been spent on evaluating why these problems were discovered only once the satellites reached orbit. This paper details the downfalls of relying heavily on link budgets and improper long range test setups, then experimentally determines the sensitivity of PolySat's …

Radio Direction Finding Network Receiver Design For Low-Cost Public Service Applications, Marcel Colman Eric Stieber

Master's Theses

A low-cost radio direction finding (RDF) VHF receiver has been investigated for development into a radio direction finding network (RDFN) with a particular focus towards public service and commercial asset tracking applications. The primary design criteria were reproducibility, low-cost, and simplicity such that public service and volunteer organizations can benefit from the technology. Two receiver designs were built and tested to allow for comparison of practicality, cost, and accuracy. A pseudo-Doppler RDF and a time difference of arrival (TDOA) receiver were built as proof-of-concept for a system design based on commercial off-the-shelf (COTS) components. The pseudo-Doppler system is a less …

Noise Reduction With Microphone Arrays For Speaker Identification, Zachary Gideon Cohen

Master's Theses

The presence of acoustic noise in audio recordings is an ongoing issue that plagues many applications. This ambient background noise is difficult to reduce due to its unpredictable nature. Many single channel noise reduction techniques exist but are limited in that they may distort the desired speech signal due to overlapping spectral content of the speech and noise. It is therefore of interest to investigate the use of multichannel noise reduction algorithms to further attenuate noise while attempting to preserve the speech signal of interest.

Specifically, this thesis looks to investigate the use of microphone arrays in conjunction with multichannel …