Signal Processing Commons^™

The Use Of Supercapacitors To Stabilize The Power Supply System Of The Base Station Of Mobile Communication, Dilmurod Abdujalilovich Davronbekov, Utkir Karimovich Matyokubov

Scientific-technical journal

In this study, an analysis of the current status and available outages of the mobile communication base station power supply system was performed. The effects of these outages on the power supply system have been studied and it has been shown that batteries may not be an ideal solution as a backup source. Also, the issue of the introduction of renewable energy sources in the base station power supply system of the mobile communication system and its shortcomings are mentioned. In order to overcome these problems and stabilize the power changes in the battery auxiliary element and the power supply …

The Use Of Supercapacitors To Stabilize The Power Supply System Of The Base Station Of Mobile Communication, Dilmurod Abdujalilovich Davronbekov, Utkir Karimovich Matyokubov

Scientific-technical journal

In this study, an analysis of the current status and available outages of the mobile communication base station power supply system was performed. The effects of these outages on the power supply system have been studied and it has been shown that batteries may not be an ideal solution as a backup source. Also, the issue of the introduction of renewable energy sources in the base station power supply system of the mobile communication system and its shortcomings are mentioned. In order to overcome these problems and stabilize the power changes in the battery auxiliary element and the power supply …

Channel Estimation In Multi-User Massive Mimo Systems By Expectation Propagation Based Algorithms, Mohammed Rashid

LSU Doctoral Dissertations

Massive multiple input multiple output (MIMO) technology uses large antenna arrays with tens or hundreds of antennas at the base station (BS) to achieve high spectral efficiency, high diversity, and high capacity. These benefits, however, rely on obtaining accurate channel state information (CSI) at the receiver for both uplink and downlink channels. Traditionally, pilot sequences are transmitted and used at the receiver to estimate the CSI. Since the length of the pilot sequences scale with the number of transmit antennas, for massive MIMO systems downlink channel estimation requires long pilot sequences resulting in reduced spectral efficiency and the so-called pilot …

Utilizing Software Defined Radios For Increased Bandwidth In Satellite Communications, Brian M. Wright

Theses and Dissertations

This research explores the background and future possibilities of using cooperative satellites equipped with Software Defined Radios (SDRs) to combine their bandwidth and increase their signal reliability. Software Defined Radios are a potential solution to realize various software applications that support a reconfigurable and adaptive communication system without altering any hardware devices or features. This benefit, along with others that are offered by SDRs and the ongoing improvements in commercial digital electronics have sparked an interest in developing small satellites for advanced communications. This research effort sets out to prove if a high bandwidth signal can be generated by using …

Laser Illuminated Imaging: Beam And Scene Deconvolution Algorithm, Benjamin W. Davis

Theses and Dissertations

Laser illuminated imaging systems deal with several physical challenges that must be overcome to achieve high-resolution images of the target. Noise sources like background noise, photon counting noise, and laser speckle noise will all greatly affect the imaging systems ability to produce a high-resolution image. An even bigger challenge to laser illuminated imaging systems is atmospheric turbulence and the effect that it will have on the imaging system. The illuminating beam will experience tilt, causing the beam to wander off the center of the target during propagation. The light returning to the detector will similarly be affected by turbulence, and …

Comparison Of Conic Ray Tracing For Occlusion Determination On 3d Point Cloud Data, Henry Cho

Theses and Dissertations

The US Air Force has been increasing the use of automation in its weapon systems to include the remotely piloted aircraft (RPA) platforms. The RPA career field has had issues with poor pilot retention due to job stressors. For example, RPA operators spend a lot of time and attention surveilling a suspect on the ground for many hours, so adding automation to this activity could help improve pilot retention. The research problem in this thesis attempted to automate the process of observing a ground target. This thesis presents a method termed conic ray tracing for determining visibility and occlusion of …

Performance Analysis Of Long-Term Evoluution Signals In Passive Bistatic Radar Applications Using Reduced Dimension Space-Time Adaptive Processing Techniques, Sureshan Suntharalingam

Theses and Dissertations

Widespread availability of long term evolution (LTE) signals makes them potential for use in passive bistatic radar (PBR) applications. However, their utility in such applications is yet to be fully explored. This research focuses on the key LTE signal attributes, such as subcarrier modulation schemes and bandwidth, and their effect on PBR application. space-time adaptive processing (STAP) concepts, both full dimension STAP (FD-STAP) reduced dimension STAP (RD-STAP), were employed to evaluate and compare the effects of varying these signal attributes, in terms of signal to interference-plus-noise ratio (SINR) loss metrics. Simulation results concluded that decreasing LTE signal's bandwidth and increasing …

Indoor Navigation Using Convolutional Neural Networks And Floor Plans, Ricky D. Anderson

Theses and Dissertations

The goal of this thesis is to evaluate a new indoor navigation technique by incorporating floor plans along with monocular camera images into a CNN as a potential means for identifying camera position. Building floor plans are widely available and provide potential information for localizing within the building. This work sets out to determine if a CNN can learn the architectural features of a floor plan and use that information to determine a location. In this work, a simulated indoor data set is created and used to train two CNNs. A classification CNN, which breaks up the floor plan into …

Mitigating The Multipath Effects On Radio Tomographic Imaging, Destinee N. Battle

Theses and Dissertations

Various radio tomographic imaging (RTI) models and reconstruction methods are equipped with capabilities to mitigate the effects of multipath interference. This thesis combined the network shadowing (NeSh) and weighting-g models in conjunction with Tikhonov regularization and low-rank and sparse decomposition (LRSD). MATLAB was used to implement the four combinations for six experimental data sets and produce attenuation images. The attenuation images were analyzed qualitatively and quantitatively to accomplish the goal of determining which combination performed best at locating human targets. After analyzing the results, it was determined that no single combination outperformed the others for at least three out of …

Optical Study Of 2-D Detonation Wave Stability, Eulaine T. Grodner

Theses and Dissertations

Fundamental optical detonation study of detonations constricted to a 2-d plane propagation, and detonations propagating around a curve. All images were processed using modern image processing techniques. The optical techniques used were shadowgraph, Schlieren, and chemiluminescence. In the 2-Dstraight channels, it was determined wave stability was a factor of cell size. It was also determined the detonation wave thickness (area between the combustion and shockwave) was a factor of how much heat available for the detonation. For the detonations propagating around a curve, it was determined the three main classifications of wave stability were stable, unstable, and detonation wave restart. …

Spatially Separable Blind Deconvolution Of Long Exposure Astronomical Imagery, Justin S. Lee

Theses and Dissertations

In this thesis, a spatially separable blind deconvolution algorithm is demonstrated that achieves a significantly faster processing time and superior sensitivity when processing long-exposure image data of unresolvable objects from a ground-based telescope. The proposed approach takes advantage of the structure of the long exposure point spread functions radial symmetric characteristics to approximate it as a product of one dimensional horizontal and vertical intensity distributions. Objects at geosynchronous or geostationary orbit also can be well approximated as being spatially separable as they are, in general non-resolvable. The algorithms performance is measured by computing the mean-squared error compared with the true …

Simulating A Mobile Wireless Sensor Network Monitoring The Air Force Marathon, Matthew D. Eilertson

Theses and Dissertations

This thesis explores the feasibility of deploying a mobile Wireless Sensor Networks (WSN) to the Air Force (AF) Marathon in support of Air Force Research Laboratory (AFRL) research of sensor and networking infrastructure in denied or degraded environments. A simulation called MarathonSim is developed in the Objective Modular Network Testbed in C++ (OMNeT++) Discrete Event Simulator to test the performance of a mobile WSN. A full factorial design using numbers of runners, transmission powers, and routing protocols is executed to measure Packet Delivery Ratio (PDR) to a central database, average end-to-end delay of application packets, and average power consumed per …

Liver Segmentation And Liver Cancer Detection Based On Deep Convolutional Neural Network: A Brief Bibliometric Survey, Kiran Malhari Napte Mr., Anurag Mahajan Dr.

Library Philosophy and Practice (e-journal)

Background: This study analyzes liver segmentation and cancer detection work, with the perspectives of machine learning and deep learning and different image processing techniques from the year 2012 to 2020. The study uses different Bibliometric analysis methods.

Methods: The articles on the topic were obtained from one of the most popular databases- Scopus. The year span for the analysis is considered to be from 2012 to 2020. Scopus analyzer facilitates the analysis of the databases with different categories such as documents by source, year, and county and so on. Analysis is also done by using different units of analysis such …

Source Localization With Machine Learning, Arjun Gupta

Electrical and Computer Engineering ETDs

Source localization with sensor arrays have found applications across domains beginning with radar and sonar, astronomy, acoustics, bio-medical devices and more recently in autonomous cars and adaptive communication systems. The knowledge of the spatial spectrum not only provide information about the source and interference but also assists in increasing signal integrity and avoid interference. This provides an added degree of freedom in the form of spatial diversity. This research investigates spatial spectrum estimation of waveforms from the signals sampled by arbitrarily distributed sensors. Conventional high resolution algorithms such as root-MuSiC fails to perform accurate source localization due to the reliance …

Time Series Data Analysis Using Machine Learning-(Ml) Approach, Mvv Prasad Kantipudi Dr., Pradeep Kumar N.S Dr., S.Sreenath Kashyap Dr., Ss Anusha Vemuri Ms

Library Philosophy and Practice (e-journal)

Healthcare benefits related to continuous monitoring of human movement and physical activity can potentially reduce the risk of accidents associated with elderly living alone at home. Based on the literature review, it is found that many studies focus on human activity recognition and are still active towards achieving practical solutions to support the elderly care system. The proposed system has introduced a joint approach of machine learning and signal processing technology for the recognition of human's physical movements using signal data generated by accelerometer sensors. The framework adopts the concept of DSP to select very descriptive feature sets and uses …

An Lpc Pole Processing Method For Enhancing The Identification Of Dominant Spectral Features, Jin Xu, Mark Davis, Ruairí De Fréin

Articles

This paper proposes a new time-resolved spectral analysis method based on a modification to the Linear Predictive Coding (LPC) method for enhancing the identification of the dominant frequencies of a signal. The method described here is based on a z-plane analysis of the LPC poles. These poles are used to produce a series of reduced order filter transfer functions which can accurately identify and estimate the frequency of the dominant spectral features. The standard LPC method has been shown to suffer from a sensitivity to noise and its performance is dependent on the filter order. The proposed method can accurately …

Artificial Intelligence Aided Receiver Design For Wireless Communication Systems, Wenjie Xu

Theses, Dissertations and Capstones

Physical layer (PHY) design in the wireless communication field realizes gratifying achievements in the past few decades, especially in the emerging cellular communication systems starting from the first generation to the fifth generation (5G). With the gradual increase in technical requirements of large data processing and end-to-end system optimization, introducing artificial intelligence (AI) in PHY design has cautiously become a trend. A deep neural network (DNN), one of the population techniques of AI, enables the utilization of its ‘learnable’ feature to handle big data and establish a global system model. In this thesis, we exploited this characteristic of DNN as …

Matlab Modeling Of Ofdm Modulation Technique Across A 24 Khz, 48 Khz, And 3 Mhz Bandwidth In The High-Frequency Radio Band (3-30) Mhz, Josiah Myer, Tyler Collins, Sarah Taylor, Natalia Anglero

Faculty-Sponsored Student Research & Capstones

The goal of this project is to use MATLAB to model orthogonal frequency division multiplexing (OFDM) modulation technique across 24 kHz, 48 kHz, and 3 MHz bandwidths in the high frequency (HF) radio band (3-30 MHz). The purpose of our design is to make HF long distance communication faster and more reliable so that every part of the world, including the most remote parts, will have access to high speed, long distance wireless communication. Our MATLAB model will allow us to modify the bandwidth, carrier frequency, modulation type, signal to noise ratio (SNR), and image size to determine which combination …

Analog & Digital Remote Synthesizer, Adam Brunner, Andrew Cihon-Scott, Scott Grisso, Linus Wright

Williams Honors College, Honors Research Projects

The purpose of this project is to develop and design an analog synthesizer musical instrument that integrates embedded digital hardware into the design to enable control from a remote source. The use of digital hardware enables the potential for a wide range of convenient features such as sound profile saving and loading, output recording functionality, and the ability to accept digital input from another musical instrument utilizing the Musical Instrument Digital Interface (MIDI). In addition to the synthesizer itself, this project also includes the design of a companion application that can be hosted on a wide variety of consumer computing …

Fixed-Point Proximity Minimization: A Theoretical Review And Numerical Study, Daniel Weddle, Jianfeng Guo

OUR Journal: ODU Undergraduate Research Journal

This study examines the relatively recent development of a “fixed-point proximity” approach to one type of minimization problem, considers its application to image denoising, and explores convergence and divergence of the iterative algorithm beyond a (previously supplied) theoretically guaranteed convergence bound on one of the parameters (𝜆). While reviewing the fixed-point proximity approach and its application to image denoising, we aim to communicate the concepts and details in a way that will facilitate understanding for undergraduates and for scholars from other subfields. In the latter portion of our study, the numerical experiment provides thought-provoking data on the effects that parameters …

The Discrete Fourier Transform - A Practical Approach, David Dorran

Articles

These notes on the Discrete Fourier Transform include numerous practical examples that make use of audio signals.

Sensing Methods For Two-Target And Four-Target Detection In Time-Constrained Vector Poisson And Gaussian Channels, Muhammad Fahad

Dissertations, Master's Theses and Master's Reports

In this dissertation we consider a sensor scheduling or resource management problem for a vector Poisson and Gaussian channels. The input is a binary random vector and the output is a set of conditionally independent Poisson or Gaussian random variables. The objective is to design a scaling matrix, which is a linear transformation whose purpose is to entangle the different inputs, under a total given energy/time constraint. The two metrics are adopted to quantify the performance of the designed scaling matrix: mutual information and Bayesian inference. In other words, it is an experimental design problem where the objective is to …

Novel Tools For Analysis Of Disordered Sleep And Motor Behavior In Preclinical Models Of Disease, Dillon M. Huffman

Theses and Dissertations--Biomedical Engineering

Subtle changes in sleep architecture can accompany and be symptomatic of various diseases or disorders. Understanding the complex interactions between sleep and health requires the ability to characterize sleep, probe its underlying mechanisms through perturbation, and quantify dependent physiological outcomes. Rodent models have come to be accepted as a valuable tool for preclinical investigations. However, experimental tools to accomplish such research typically rely on laborious methods that limit throughput and flexibility. Thus, research tools that minimize workload could be of great value to the research community and expedite investigation of the underlying mechanisms of sleep and further the development of …

Localization Of Stationary Source Of Floor Vibration Using The Steered Response Power Method, Mohammad Royvaran

Theses and Dissertations--Civil Engineering

If the generated vibration in a building exceeds the acceptable limit design for a floor system, it is necessary to identify the source of vibration, a process known as localization. The objective of this study is the localization of stationary vibration sources, and the approach used is the steered response power (SRP) method. This method has already been shown to work well for wireless and acoustical applications to locate transmitter and sound sources, respectively. To the writer’s knowledge, this study is the first application of the SRP method to locate vibration sources using floor vibration measurements. However, because waves behave …

Ecg Arrhythmia Classification Using Discrete Wavelet Transformation, Hannah E. Chookaszian, Nathan D. Diekema

Electrical Engineering

Cardiovascular diseases (CVDs) are the highest leading cause of death worldwide with an approximate 17.9 million related deaths every year according to the World Health Organization (WHO). Electrocardiographic (EKG or ECG) signals are electrical signals measured in the heart and are the main indicator for pre-existing cardiac conditions. The application of deep learning methods such as artificial neural networks (ANN) will assist in the automated detection and classification of ECG signals. The current methods for ECG analysis are lacking in accuracy and reliability considering the level of risk involved with CVDs and the importance of a correct diagnosis. Clinicians use …

Quality Assurance Of Lightweight Structures Via Phase-Based Motion Estimation, Ikenna E. Ifekaonwu

College of Graduate Studies: Theses & Dissertations

In recent years, lightweight structures have become mature and adopted in various applications. The importance of quality assurance cannot be overemphasized hence extensive research has been conducted to assess the quality of lightweight structures. This study investigates a novel process that exploits motion magnification to investigate the damage characteristics of lightweight mission-critical parts. The goal is to assure the structural integrity of 3D printed structures and composite structures by determining the inherent defects present in the part by exploiting their vibration characteristics. The minuscule vibration of the structure was recorded with the aid of a high-speed digital camera, and the …

Deep Learning Assisted Intelligent Visual And Vehicle Tracking Systems, Liang Xu

Theses and Dissertations

Sensor fusion and tracking is the ability to bring together measurements from multiple sensors of the current and past time to estimate the current state of a system. The resulting state estimate is more accurate compared with the direct sensor measurement because it balances between the state prediction based on the assumed motion model and the noisy sensor measurement. Systems can then use the information provided by the sensor fusion and tracking process to support more-intelligent actions and achieve autonomy in a system like an autonomous vehicle. In the past, widely used sensor data are structured, which can be directly …

Novel Machine Learning And Wearable Sensor Based Solutions For Smart Healthcare Monitoring, Rajdeep Kumar Nath

Theses and Dissertations--Electrical and Computer Engineering

The advent of IoT has enabled the design of connected and integrated smart health monitoring systems. These health monitoring systems can be utilized for monitoring the mental and physical wellbeing of a person. Stress, anxiety, and hypertension are the major elements responsible for the plethora of physical and mental illnesses. In this context, the older population demands special attention because of the several age-related complications that exacerbate the effects of stress, anxiety, and hypertension. Monitoring stress, anxiety, and blood pressure regularly can prevent long-term damage by initiating necessary intervention or clinical treatment beforehand. This will improve the quality of life …

Hard Hat Ambient Liability Observer (Halo), Hunter Hykes, Nathan Kish, Brian Thomson

Williams Honors College, Honors Research Projects

Capturing workplace incident information is a growing area of concern for most companies. To assist with this, the design team proposed the H.A.L.O. This design uses time-of-flight sensors connected to LEDs to create a proximity-based hazard warning system. It also records incident data using an accelerometer and micro-SD card. This helps workers avoid some of the most common workplace injuries, slips, trips, and falls and accidental collisions.

Students have created a design with engineering, and marketing requirements that accomplish this task. The proposed design allows for this monitoring and mitigation systems to be attached to hard hats. Team members developed …

Light Loaded Automated Guided Vehicle, Marcus Radtka, Nazar Paramashchuk, Lawrence Shevock

Williams Honors College, Honors Research Projects

The objective of the locomotion system was to design and implement the mechanical, electrical, and software related functions to ensure the LLAGV had the capability of maneuvering its surroundings. The LLAGV’s motors were represented in an open loop transfer function to utilize RPM feedback and a compensator when needed. The modeled compensator helped control the LLAGV’s speed and acceleration, enabling further control of the LLAGV. The internal circuitry has the means to properly distributed power to all components and allowed the user to control the LLAGV to their desire. The application software within the LLAGV locomotion system (LLAGV-LS) had consideration …