Signal Processing Commons^™

Implementation Of Range Autofocus For Sar Radar Imaging, Nicholas J. Testin, Philip Davis

KSU Journey Honors College Capstones and Theses

The range calculation for an FMCW radar depends on accurate linear modulation. In some circumstances, linear modulation may not be available and must be corrected for. This paper describes an autofocus technique used to correct for phase error due to non-linearities in the components of a FMCW radar. Also described here is the algorithm used in calculating the phase error and application of the phase correction with triangle modulation. Known errors were calculated at certain distances and applied to correcting the phase of data taken at similar distances. The results given were generated using a SAR working outside linear ranges.

Low-Resolution Adc Receiver Design, Mimo Interference Cancellation Prototyping, And Phy Secrecy Analysis., Chen Cao

Electronic Theses and Dissertations

This dissertation studies three independent research topics in the general field of wireless communications. The first topic focuses on new receiver design with low-resolution analog-to-digital converters (ADC). In future massive multiple-input-multiple-output (MIMO) systems, multiple high-speed high-resolution ADCs will become a bottleneck for practical applications because of the hardware complexity and power consumption. One solution to this problem is to adopt low-cost low-precision ADCs instead. In Chapter II, MU-MIMO-OFDM systems only equipped with low-precision ADCs are considered. A new turbo receiver structure is proposed to improve the overall system performance. Meanwhile, ultra-low-cost communication devices can enable massive deployment of disposable wireless …

System-Layout-Dependent Thermally Induced Solder Stress & Reliability Implications, Ange C. Iradukunda

Mechanical Engineering Undergraduate Honors Theses

Electronic flip chip assemblies consist of dissimilar component materials, which exhibit different CTE. Under thermal cyclic operating conditions, this CTE mismatch produces interfacial and interconnect stresses, which are highly dependent on system layout. In this paper, sensitivity analyses are performed using ANSYS FEA to establish how the proximity and arrangement of neighboring devices affect interconnect stress. Flip chip alignment modes ranging from edge-to-edge to corner-to-corner are studied. Results of these FEA studies, demonstrated that closely packing devices together has the effect of making them act as one. This results in a significant increase in the thermomechanical stresses induced on peripheral …

Objective Assessment Of Perceptual Audio Quality Using Visqolaudio, Colm Sloan, Damien Kelly, Naomi Harte, Anil C. Kokaram, Andrew Hines

Conference papers

Digital audio broadcasting services transmit substantial amounts of data that is encoded to minimize bandwidth whilst maximizing user quality of experience. Many large service providers continually alter codecs to improve the encoding process. Performing subjective tests to validate each codec alteration would be impractical, necessitating the use of objective perceptual audio quality models. This paper evaluates the quality scores from ViSQOLAudio, an objective perceptual audio quality model, against the quality scores of PEAQ, POLQA, and PEMO-Q on three datasets containing fullband audio encoded with a variety of codecs and bitrates. The results show that ViSQOLAudio was more accurate than all …

Unmanned Aerial Vehicle Tracking System With Out-Of-Sequence Measurement In A Discrete Time-Delayed Extended Kalman Filter, Roque Lora

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The goal of this thesis is to extend the delayed Kalman filter so it can be used with non-linear systems and that it can handle randomized delays on the measurements. In the particular case of this study, the filter is used to estimates the states of an unmanned aerial system. The outputs of the filter are used to point an antenna and a camera towards a UAS. Different scenarios are simulated for the purpose of comparing the efficiency of this technique in various situations.

5g-Ucda Multi Antenna-To-Logical Cell Circular Fifo Mapping Strategy For High-Speed Train Wireless Communications, Subharthi Banerjee

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

2020 is the target year for the roll out of fifth generation wireless communication methodologies. The commercial vendors have characterized 5G as a collection of disruptive set of technologies to provide high throughput, low latency communication supporting a variety of services, i.e., machine to machine communication to next generation base stations and vehicle-to-vehicle communication to radio-over-fiber and high mobility channels. High-speed train wireless communication channels as a subset of high mobility channels have their clear advantages and disadvantages considering other vehicular channels. The speed of high-speed trains is going to reach 500km/hr and with Hyperloop it may reach 1000km/hr. LTE …

Microstrip Patch Antenna Design, Simulation, And Optimization At X-Band, Alfred Setyono, Beatrix Setyono, Victoria Eccles

Research Horizons Day Posters

No abstract provided.

Satellite Communications In The V And W Band: Natural And Artificial Scintillation Effects, David A. Smith

Theses and Dissertations

In a natural atmospheric environment the troposphere will be the primary source of loss with the ionosphere loss being negligible. If the ionosphere was disturbed from a high altitude nuclear explosion (HANE) more than three times the amount of electrons would be present in the ionosphere and could represent a source of significant loss. In order to determine the amount of electrons distributed from a HANE, GSCENARIO, developed by Defense Threat Reduction Agency was used. The two sources of loss that were examined was signal absorption and amplitude scintillation. Signal loss was determined using GSCENARIO and amplitude scintillation loss was …

Sound Based Positioning, David L. Weathers

Theses and Dissertations

With a growing interest in non-GPS positioning, navigation, and timing (PNT), sound based positioning provides a precise way to locate both sound sources and microphones through audible signals of opportunity (SoOPs). Exploiting SoOPs allows for passive location estimation. But, attributing each signal to a specific source location when signals are simultaneously emitting proves problematic. Using an array of microphones, unique SoOPs are identified and located through steered response beamforming. Sound source signals are then isolated through time-frequency masking to provide clear reference stations by which to estimate the location of a separate microphone through time difference of arrival measurements. Results …

Silent Communication Device, Christopher Wayne Schutter

Master's Theses

Oral communication has constituted as a necessary aspect of how people interact with one another, but there are always situations where this form of communication can create distractions, irritation, or even danger. Take for example, a student in a laboratory who needs to communicate effectively with a lab partner without creating a distraction to those trying to work around said student or a soldier on a battlefield who needs to relay information effectively to his or her comrades without revealing his or her position to the enemy. It becomes apparent that people need a more exclusive form of communication in …

Thermal Evolution Of Moon, Arshdeep Singh Gill

Master's Theses

In August, 2014 three experiments were conducted using infrared systems deployed at White Mountain Research center, CA. The data was acquired for the whole month of August. Teams of 3-4 students from Cal Poly San Luis Obispo and UC Santa Barbara were stationed at the research center for 2-3 days to operate the equipment. The three experiments were:(1) creating spatial-temporal time series of lunar surface temperatures;(2) identifying atmospheric meteor trails;(3) search for meteor impacts on the Moon surface. Out of the three this thesis focusses on experiment 1 and the results from this experiment could also help with the other …

The Fresnel Zone Light Field Spectral Imager, Francis D. Hallada

Theses and Dissertations

This thesis provides a computational model and the first experimental demonstration of a Fresnel zone light field spectral imaging (FZLFSI) system. This type of system couples an axial dispersion binary diffractive optic with light field (plenoptic) camera designs providing a snapshot spectral imaging capability. A computational model of the system was developed based on wave optics methods using Fresnel propagation. It was validated experimentally and provides excellent demonstration of system capabilities. The experimentally demonstrated system was able to synthetically refocus monochromatic images across greater than a 100nm bandwidth. Furthermore, the demonstrated system was modeled to have a full range of …

T1, T2, And Off-Resonance Mapping Using A Non-Linear Least-Squares Fit Of The Bssfp Signal, Meredith Taylor, Joseph Valentine, Steven Whitaker, Neal Bangerter

Biomedical Engineering Western Regional Conference

The mapping of MR relaxation times has found a broad variety of applications in the study of disease. Unfortunately, the gold standards for acquiring T₁ and T₂ maps require long scan times, and are therefore more suited to 2D acquisitions with limited slices. For reasonable scan times, resolution is limited making these scans less useful for showing fine morphological detail. A rapid 3D sequence at higher resolutions that could be used to provide both morphological detail and relaxation time maps would be particularly useful. We propose a technique with potential to provide simultaneous band-free 3D datasets and estimates …

Water Fat Separation With Multiple-Acquisition Bssfp Mri, Michael A. Mendoza 8232743, Joseph Valentine, Neal Bangerter

Biomedical Engineering Western Regional Conference

We present a technique that combines the advantages of bSSFP MRI with Dixon reconstruction in order to produce robust water fat separation with high SNR in a short imaging time, while simultaneously reducing banding artifacts that traditionally degrade image quality.

Time-Frequency Masking Performance For Improved Intelligibility With Microphone Arrays, Joshua P. Morgan

Theses and Dissertations--Electrical and Computer Engineering

Time-Frequency (TF) masking is an audio processing technique useful for isolating an audio source from interfering sources. TF masking has been applied and studied in monaural and binaural applications, but has only recently been applied to distributed microphone arrays. This work focuses on evaluating the TF masking technique's ability to isolate human speech and improve speech intelligibility in an immersive "cocktail party" environment. In particular, an upper-bound on TF masking performance is established and compared to the traditional delay-sum and general sidelobe canceler (GSC) beamformers. Additionally, the novel technique of combining the GSC with TF masking is investigated and its …

2017 State Of Resnet Report Acuta/Acuho-1

ACUTA: Other Publications

Copyright 2017 Association for College and University Technology Advancement & Association of College and University Housing Officers -International 2017

An Acoustic-Based Approach For Condition Monitoring Of Pipes, Muhammad S. Khan, Turaj Ashuri, Mitchell Collins, Geoffrey Birkemeier, Emad Almohmmedali

Journal of the Arkansas Academy of Science

Polyvinyl chloride pipes are extensively used in municipal sewer systems. As the sewer system ages, polyvinyl chloride pipes become prone to developing cracks that can release toxic effluents into the environment. Traditionally, utility operators pass a close circuit television camera mounted on a guided vehicle through the pipe to monitor the defects. The video is observed by a trained operator who records the condition of the pipe. This arrangement has two major limitations. First, it is expensive due to complex set up. Second, if a pipe is blocked the guided vehicle cannot pass through its entire length. A more economical …

Lip Detection And Adaptive Tracking, Benjamin Wang

Master's Theses

Performance of automatic speech recognition (ASR) systems utilizing only acoustic information degrades significantly in noisy environments such as a car cabins. Incorporating audio and visual information together can improve performance in these situations. This work proposes a lip detection and tracking algorithm to serve as a visual front end to an audio-visual automatic speech recognition (AVASR) system.

Several color spaces are examined that are effective for segmenting lips from skin pixels. These color components and several features are used to characterize lips and to train cascaded lip detectors. Pre- and post-processing techniques are employed to maximize detector accuracy. The trained …

High Performance Multiview Video Coding, Caoyang Jiang

Dissertations, Master's Theses and Master's Reports

Following the standardization of the latest video coding standard High Efficiency Video Coding in 2013, in 2014, multiview extension of HEVC (MV-HEVC) was published and brought significantly better compression performance of around 50% for multiview and 3D videos compared to multiple independent single-view HEVC coding. However, the extremely high computational complexity of MV-HEVC demands significant optimization of the encoder. To tackle this problem, this work investigates the possibilities of using modern parallel computing platforms and tools such as single-instruction-multiple-data (SIMD) instructions, multi-core CPU, massively parallel GPU, and computer cluster to significantly enhance the MVC encoder performance. The aforementioned computing tools …

Experimental Investigation Of Reading Passive Uhf Tags In A Multi-Tag Environment, Yi Zhou

Theses and Dissertations--Mechanical and Aerospace Engineering

Recently, the Internet of things (IoT) has emerged as a promising solution for several industrial applications. One of the key components in IoT is passive radio frequency identification (RFID) tags which do not require a power source for operations. Specifically, ultra-high frequency (UHF) tags are studied in this paper. However, due to factors such as tag-to-tag interference and inaccurate localization, RFID tags that are closely spaced together are difficult to detect and program accurately with unique identifiers. This thesis investigates several factors that affect the ability to encode a specific tag with unique information in the presence of other tags, …

Accuracy And Repeatability Of Single-Pose Calibration Of Inertial Measurement Units For Whole-Body Motion Analysis, Xavier Robert-Lachaine, Hakim Mecheri, Christian Larue, André Plamondon

Études primaires

Portable inertial measurement units (IMUs) are suitable for motion analysis outside the laboratory. However, IMUs depend on the calibration of each body segment to measure human movement. Different calibration approaches have been developed for simplicity of use or similarity to laboratory motion analysis, but they have not been extensively examined. The main objective of the study was to determine the accuracy and repeatability of two common single-pose calibrations (N-pose and T-pose) under different conditions of placement (self-placement and passive placement), as well as their similarity to laboratory analysis based on anatomical landmarks. A further aim of the study was to …

Respiratory Prediction And Image Quality Improvement Of 4d Cone Beam Ct And Mri For Lung Tumor Treatments, Seonyeong Park

Theses and Dissertations

Identification of accurate tumor location and shape is highly important in lung cancer radiotherapy, to improve the treatment quality by reducing dose delivery errors. Because a lung tumor moves with the patient's respiration, breathing motion should be correctly analyzed and predicted during the treatment for prevention of tumor miss or undesirable treatment toxicity. Besides, in Image-Guided Radiation Therapy (IGRT), the tumor motion causes difficulties not only in delivering accurate dose, but also in assuring superior quality of imaging techniques such as four-dimensional (4D) Cone Beam Computed Tomography (CBCT) and 4D Magnetic Resonance Imaging (MRI). Specifically, 4D CBCT used in CBCT …

Accurate Acoustic Ranging System Using Android Smartphones, Mohammadbagher Fotouhi

Theses and Dissertations

ACCURATE ACOUSTIC RANGING SYSTEM USING ANDROID SMARTPHONES

By Mohammadbagher Fotouhi, Master of Science

A thesis submitted in partial fulfillment of the requirements for the degree of Master of Science at Virginia Commonwealth University

Virginia Commonwealth University 2017

Major Director: Dr. Ruixin Niu, Associate Professor of Department of Electrical and Computer Engineering

In this thesis, we present the design, implementation, and evaluation of an android ranging system, a high-accuracy acoustic-based ranging system which allows two android mobile phones to learn their physical distance from each other.

In this system we propose a practical solution for accurate ranging based on acoustic communication …

Sensor Characterization And Signal Fusion For Instanteye, Wyman T. Smith

Honors Theses and Capstones

The practicality and effectiveness of using a TerraRanger Duo—a parallel sonar and infrared time-of-flight distance sensor—payload for obstacle detection is investigated for use with Physical Science Inc.’s InstantEye drone. A Python program was developed to interface with the serial data output before comparing the sensor’s empirical performance against its data sheet. The two signals from the distinct sensor modules, each with their characterized strengths and weaknesses, were then fused with a Kalman filter. This was further refined by imposing conditional weighting based on the known sensor characteristics. The filter output, with conditional corrections, was able to accurately track a single …

Detection Of Fatigue Damage In Shear Connections Using Acoustic Wave Propagation, Zichao Wang

Dissertations, Master's Theses and Master's Reports

Fatigue damage is an important concern in structural steel connections where frequent load reversals are expected. Detection of fatigue damage is typically done with infrequent visual inspections that are subjective and limited to surface features. A permanent embedded structural health monitoring (SHM) system could be helpful in detecting damage as it occurs. Current methods for detecting fatigue damage include inference of fatigue life expended through cycle counting from long-term strain measurement campaigns, and through short-term impedance measurements. The first approach has the advantage that it is relatively simple from an algorithmic point of view, but it is an indirect measure …

Performance Simulation And Optimization Of A Simultaneous Transmit And Receive Phased Antenna Array Using Adaptive Beamforming And Genetic Algorithm Techniques, Ian Thomas Cummings

Dissertations, Master's Theses and Master's Reports

The development of simultaneous transmit and receive capabilities is on the cutting-edge of research in phased array technology [1, 2, 3]. The large disparity in power between the transmitted and received signals in antenna systems has traditionally prevented operation in a simultaneous mode. However, simultaneous transmit and receive offers great opportunities for increased capabilities and performance in communications, radar, and electronic warfare applications [3]. This technology will be made feasible by realizing a high level of isolation between the transmitted and received signals through a variety of techniques. This work explores the feasibility of choosing non-standard array partitions that--when paired …

Stringless Guitar, Kue Z. Yang, Anthony Batey, Dominic Mercorelli, Nathaniel Hawk

Williams Honors College, Honors Research Projects

The aim of this project is to improve the design of a typical guitar by designing a digital stringless guitar. Due to the nonlinearities inherent in a guitar, it would be difficult to reproduce guitar tones by summing harmonic components; therefore, digital samples of guitar tones were taken in order to preserve these unique and wonderfully sounding tones. These digital samples were stored in the guitar and used to produce its tones when played. The digital guitar includes fingerboard position sensors as well as strum sensors for each string. The fingerboard position sensors detect the player’s fingers at discrete positions. …

System For Workout Information Management, Mark Archual, Ethan E. Schweinsberg

Williams Honors College, Honors Research Projects

Power racks are a weight machine used by swimmers to provide resistance while they swim away from a wall toward the center of the pool. The objective of this project is to build a modular data system that can be added to these machines to record and log quantitative information during their use. This information will be stored on a web server, and made available to the user for analysis and visualization through a web application. Workout data can also be downloaded and interpreted at a later time, independent of the web application. The data system should be water resistant, …

Constant False Alarm Rate Performance Of Sound Source Detection With Time Delay Of Arrival Algorithm, Xipeng Wang

Theses and Dissertations--Electrical and Computer Engineering

Time Delay of Arrival (TDOA) based algorithms and Steered Response Power (SRP) based algorithms are two most commonly used methods for sound source detection and localization. SRP is more robust under high reverberation and multi-target conditions, while TDOA is less computationally intensive. This thesis introduces a modified TDOA algorithm, TDOA delay table search (TDOA-DTS), that has more stable performance than the original TDOA, and requires only 4% of the SRP computation load for a 3-dimensional space of a typical room. A 2-step adaptive thresholding procedure based on a Weibull noise peak distributions for the cross-correlations and a binomial distribution for …

Audio-Based Productivity Forecasting Of Construction Cyclic Activities, Chris A. Sabillon

College of Graduate Studies: Theses & Dissertations

Due to its high cost, project managers must be able to monitor the performance of construction heavy equipment promptly. This cannot be achieved through traditional management techniques, which are based on direct observation or on estimations from historical data. Some manufacturers have started to integrate their proprietary technologies, but construction contractors are unlikely to have a fleet of entirely new and single manufacturer equipment for this to represent a solution. Third party automated approaches include the use of active sensors such as accelerometers and gyroscopes, passive technologies such as computer vision and image processing, and audio signal processing. Hitherto, most …