Signal Processing Commons^™

A Sindy Hardware Accelerator For Efficient System Identification On Edge Devices, Michael Sean Gallagher

Master's Theses

The SINDy (Sparse Identification of Non-linear Dynamics) algorithm is a method of turning a set of data representing non-linear dynamics into a much smaller set of equations comprised of non-linear functions summed together. This provides a human readable system model the represents the dynamic system analyzed. The SINDy algorithm is important for a variety of applications, including high precision industrial and robotic applications. A Hardware Accelerator was designed to decrease the time spent doing calculations. This thesis proposes an efficient hardware accelerator approach for a broad range of applications that use SINDy and similar system identification algorithms. The accelerator is …

Evaluating Eeg–Emg Fusion-Based Classification As A Method For Improving Control Of Wearable Robotic Devices For Upper-Limb Rehabilitation, Jacob G. Tryon

Electronic Thesis and Dissertation Repository

Musculoskeletal disorders are the biggest cause of disability worldwide, and wearable mechatronic rehabilitation devices have been proposed for treatment. However, before widespread adoption, improvements in user control and system adaptability are required. User intention should be detected intuitively, and user-induced changes in system dynamics should be unobtrusively identified and corrected. Developments often focus on model-dependent nonlinear control theory, which is challenging to implement for wearable devices.

One alternative is to incorporate bioelectrical signal-based machine learning into the system, allowing for simpler controller designs to be augmented by supplemental brain (electroencephalography/EEG) and muscle (electromyography/EMG) information. To extract user intention better, sensor …

Improved Vehicle-Bridge Interaction Modeling And Automation Of Bridge System Identification Techniques, Omar Abuodeh

All Dissertations

The Federal Highway Administration (FHWA) recognizes the necessity for cost-effective and practical system identification (SI) techniques within structural health monitoring (SHM) frameworks for asset management applications. Indirect health monitoring (IHM), a promising SHM approach, utilizes accelerometer-equipped vehicles to measure bridge modal properties (e.g., natural frequencies, damping ratios, mode shapes) through bridge vibration data to assess the bridge's condition. However, engineers and researchers often encounter noise from road roughness, environmental factors, and vehicular components in collected vehicle signals. This noise contaminates the vehicle signal with spurious modes corresponding to stochastic frequencies, impacting damage monitoring assessments. Thus, an efficient and reliable SI …

Programmable Vibration Table Retrofit With Eagle Medical, Jonathan Ilagan, Madhav Asok, Max Lewter

Biomedical Engineering

This project aimed to repair and upgrade a vibration table used for package testing for the sponsor, Eagle Medical - a medical packaging and sterilization company based in Paso Robles, California. The current vibration table is not programmable and lacks circuit diagrams, making it difficult to repair. In addition, it is not functional due to internal circuitry issues and power requirements. To address these issues, the team will implement several upgrades to improve the product and allow for better random cyclic vibration testing. A full assessment of the existing vibration table will be conducted to ensure the viability of these …

Instrumented Control Column For Optionally Piloted Aircraft, Andrew J. Klein

Electrical Engineering

Natilus, an aerospace company that is rapid-prototyping optionally piloted aircraft (OPA) for the shipping industry, needs a system that retrieves control column position data in order to manipulate flight simulator parameters in software. At present, a universally compatible system for all aircraft does not exist. Typically, established aerospace companies will sink significant time and money into developing proprietary systems for control column data retrieval as every aircraft is unique in its layout and linkage design. However, as a startup developing their first aircraft, Natilus does not have the privilege of modifying an existing sensor system to work with their HIL …

Chatgpt As Metamorphosis Designer For The Future Of Artificial Intelligence (Ai): A Conceptual Investigation, Amarjit Kumar Singh (Library Assistant), Dr. Pankaj Mathur (Deputy Librarian)

Library Philosophy and Practice (e-journal)

Abstract

Purpose: The purpose of this research paper is to explore ChatGPT’s potential as an innovative designer tool for the future development of artificial intelligence. Specifically, this conceptual investigation aims to analyze ChatGPT’s capabilities as a tool for designing and developing near about human intelligent systems for futuristic used and developed in the field of Artificial Intelligence (AI). Also with the helps of this paper, researchers are analyzed the strengths and weaknesses of ChatGPT as a tool, and identify possible areas for improvement in its development and implementation. This investigation focused on the various features and functions of ChatGPT that …

Research Of Three-Phases Current’S Transducers Of Filter-Compensation Devices For Control Reactive Power’S Consumption Of Asynchronous Motor, Ilkhomjon Khakimovich Siddikov, Dilyorbek Karimjonov Doniyorbek O'G'Li -, Abdumutal Abdikarimovich Abdigapirov

Chemical Technology, Control and Management

In the article given materials of developing of three-phase electromagnetic current transducers of reactive power, using with asynchronous motor, methods connecting of two sensing element, series, parallel and differential and loops suitable for each phase, dynamic characteristics of output signals of three-phase electromagnetic current transducers asynchronous motor.

On the basis of modern calculation and design complexes are of great importance in the research variable sizes of three-phase current electromagnetic transducers of filter-compensation devices of reactive power of asynchronous motors. Presented mathematical model of research of electrical, electromagnetic and magnetic elements of electromagnetic current transducers in the …

Enhancing Traffic Safety In Unpredicted Environments With Integration Of Adas Features With Sensor Fusion In Intelligent Electric Vehicle Platform With Implementation Of Environmental Mapping Technology, David S. Obando Ortegon

Electronic Theses and Dissertations

A major objective on society is to reduce the number of accidents and fatalities on the road for drivers, and pedestrians. Therefore, the automotive engineering field is working on this problem through the development and integration of safety technologies such as advanced driving assistance systems. For this reason, this work was intended to develop and evaluate the performance of different ADAS features and IV technologies under unexpected scenarios. This by the development of safety algorithms applied to the intelligent electric vehicle designed and built in this work, through the use of ADAS sensors based on sensor fusion. Evaluation of AEB, …

Diy Cell Incubator, Hayden James Jeanor

Electrical Engineering

The purpose of creating a cell Incubator is for the development of cell and tissue production in laboratory settings. Large scale research projects and the medical community grow cells for various reasons, including experiments and creating tissue for patients. However, they cannot simply depend on growing cells in a petri dish that sit on a rack at room temperature. To grow heathy cells in the fastest way possible, they use cell incubators. Cell incubators create an atmosphere within the incubation bay that is designed to promote cell growth. The three main components that need to be constantly regulated, using a …

Hybrid Smart Transformer For Enhanced Power System Protection Against Dc With Advanced Grid Support, Moazzam Nazir

All Dissertations

The traditional grid is rapidly transforming into smart substations and grid assets incorporating advanced control equipment with enhanced functionalities and rapid self-healing features. The most important and strategic equipment in the substation is the transformer and is expected to perform a variety of functions beyond mere voltage conversion and isolation. While the concept of smart solid-state transformers (SSTs) is being widely recognized, their respective lifetime and reliability raise concerns, thus hampering the complete replacement of traditional transformers with SSTs. Under this scenario, introducing smart features in conventional transformers utilizing simple, cost-effective, and easy to install modules is a highly desired …

Closed-Loop Brain-Computer Interfaces For Memory Restoration Using Deep Brain Stimulation, David Xiaoliang Wang

Electrical Engineering Theses and Dissertations

The past two decades have witnessed the rapid growth of therapeutic brain-computer interfaces (BCI) targeting a diversity of brain dysfunctions. Among many neurosurgical procedures, deep brain stimulation (DBS) with neuromodulation technique has emerged as a fruitful treatment for neurodegenerative disorders such as epilepsy, Parkinson's disease, post-traumatic amnesia, and Alzheimer's disease, as well as neuropsychiatric disorders such as depression, obsessive-compulsive disorder, and schizophrenia. In parallel to the open-loop neuromodulation strategies for neuromotor disorders, recent investigations have demonstrated the superior performance of closed-loop neuromodulation systems for memory-relevant disorders due to the more sophisticated underlying brain circuitry during cognitive processes. Our efforts are …

System Design And Control Optimization For Neurorehabilitation Exoskeleton, Rodrigo N. Ramon

FIU Electronic Theses and Dissertations

Neurorehabilitation is a comprehensive approach aimed at helping patients regain motor control after a neural injury, including spinal cord injury, stroke, or other ischemic events. Early-stage neurorehabilitation is particularly delicate due to voluntary muscular weakness and lack of motor control, presenting in the form of spasticity. Unfortunately, this period of elevated weakness is when most neural control improvement can be made through a phenomenon called brain plasticity. Early rehabilitation traditionally requires a human therapist due to the adaptive and dynamic interpretation of undesired neuromuscular events. While efforts have been made to develop devices to aid in neurorehabilitation, the considerations that …

Real-Time Parkinsonian Tremor Signal Identifier Based On Internal Model Principle, Jian Dong

Electronic Thesis and Dissertation Repository

Parkinsonian tremor is one of the clinical hallmarks of Parkinson's disease. Since the traditional medical treatments are not effective, many wearable devices are developed to help suppress the tremor. In order to suppress the tremor, a well-designed tremor estimator is needed. Previous tremor estimators treat a 3-D tremor signal as three independent 1-D signals. Moreover, they did not consider the real-life characteristics of tremor signals. For instance, the tremor does not always exist in the postural tremor signal, and the patient's voluntary motion can be included in the kinetic tremor signal. This paper presents a real-time adaptive parkinsonian tremor signal …

Direct Torque Control For Silicon Carbide Motor Drives, Mohammad Hazzaz Mahmud

Graduate Theses and Dissertations

Direct torque control (DTC) is an extensively used control method for motor drives due to its unique advantages, e.g., the fast dynamic response and the robustness against motor parameters variations, uncertainties, and external disturbances. Using higher switching frequency is generally required by DTC to reduce the torque ripples and decrease stator current total harmonic distortion (THD), which however can lower the drive efficiency. Through the use of the emerging silicon carbide (SiC) devices, which have lower switching losses compared to their silicon counterparts, it is feasible to achieve high efficiency and low torque ripple simultaneously for DTC drives.

To overcome …

Development Of A Wearable Haptic Feedback Device For Upper Limb Prosthetics Through Sensory Substitution, Marco B.S. Gallone

Electronic Thesis and Dissertation Repository

Haptics can enable a direct communication pipeline between the artificial limb and the brain; adding haptic sensory feedback for prosthesis wearers is believed to improve operation without drawing too much of the user's attention. Through neuroplasticity, the brain can become more cognizant of the information delivered through the skin and may eventually interpret it as inherently as other natural senses. In this thesis, a wearable haptic feedback device (WHFD) is developed to communicate prosthesis sensory information. A 14-week, 6-stage, between subjects study was created to investigate the learning trajectory as participants were stimulated with haptic patterns conveying joint proprioception. 37 …

Data Forgery Detection In Automatic Generation Control: Exploration Of Automated Parameter Generation And Low-Rate Attacks, Yatish R. Dubasi

Computer Science and Computer Engineering Undergraduate Honors Theses

Automatic Generation Control (AGC) is a key control system utilized in electric power systems. AGC uses frequency and tie-line power flow measurements to determine the Area Control Error (ACE). ACE is then used by the AGC to adjust power generation and maintain an acceptable power system frequency. Attackers might inject false frequency and/or tie-line power flow measurements to mislead AGC into falsely adjusting power generation, which can harm power system operations. Various data forgery detection models are studied in this thesis. First, to make the use of predictive detection models easier for users, we propose a method for automated generation …

Design And Control Of A Peristaltic Pump To Simulate Left Atrial Pressure In A Conductive Silicone Model, Jeremy Collins

Mechanical Engineering Undergraduate Honors Theses

According to the CDC, atrial fibrillation is responsible for more than 454,000 hospitalizations and approximately 158,000 deaths per year. A common treatment for atrial fibrillation is catheter ablation, a process in which a long flexible tube is guided through the femoral artery and to the source of arrhythmia in the heart, where it measures the electrical potential at various locations and converts problematic heart tissue to scar tissue via ablation. This paper details the design and control of a low-cost ($400) peristaltic pump system using repetitive control to replicate blood pressure in the left atrium in a conductive silicone model …

Distance-Based Formation Control Using Decentralized Sensing With Infrared Photodiodes, Steven Williams

LSU Master's Theses

This study presents an onboard sensor system for determining the relative positions of mobile robots, which is used in decentralized distance-based formation controllers for multi-agent systems. This sensor system uses infrared photodiodes and LEDs; its effective use requires coordination between the emitting and detecting robots. A technique is introduced for calculating the relative positions based on photodiode readings, and an automated calibration system is designed for future maintenance. By measuring the relative positions of their neighbors, each robot is capable of running an onboard formation controller, which is independent of both a centralized controller and a global positioning-like system (e.g., …

Light Loaded Automated Guided Vehicle, Marcus Radtka, Nazar Paramashchuk, Lawrence Shevock

Williams Honors College, Honors Research Projects

The objective of the locomotion system was to design and implement the mechanical, electrical, and software related functions to ensure the LLAGV had the capability of maneuvering its surroundings. The LLAGV’s motors were represented in an open loop transfer function to utilize RPM feedback and a compensator when needed. The modeled compensator helped control the LLAGV’s speed and acceleration, enabling further control of the LLAGV. The internal circuitry has the means to properly distributed power to all components and allowed the user to control the LLAGV to their desire. The application software within the LLAGV locomotion system (LLAGV-LS) had consideration …

An Exploratory Study Of Pulse Width And Delta Sigma Modulators, Logan B. Penrod

Master's Theses

This paper explores the noise shaping and noise producing qualities of Delta-Sigma Modulators (DSM) and Pulse-Width Modulators (PWM). DSM has long been dominant in the Delta Sigma Analog-to-Digital Converter (DSADC) as a noise-shaped quantizer and time discretizer, while PWM, with a similar self oscillating structure, has seen use in Class D Power Amplifiers, performing a similar function. It has been shown that the PWM in Class D Amplifiers outperforms the DSM [1], but could this advantage be used in DSADC use-cases? LTSpice simulation and printed circuit board implementation and test are used to present data on four variations of these …

A Study Of Static And Dynamic Characteristics Of Multifunctional Signal Converters, Akmal Abdumalikov

Chemical Technology, Control and Management

The issues of continuity, accuracy, speed and reliability of signal conversion, which are the main problems of quality control and management of production processes, remain relevant. Research shows that in practice there are different signal variables, the study of which is highly formalized in a number of modeling tasks and basic classification studies, in particular transients in converters, its sources and elements requires a unified mathematical approach, that is, visual, highly formalized modeling and research based on it. The paper presents a graph model of multifunctional signal converters that provide microprocessor and electronic devices with signals in the form of …

Robust Control Of Burst Suppression Amid Physical And Neurological Uncertainty, Stephen Ampleman, Shinung Ching

McKelvey School of Engineering Theses & Dissertations

Burst suppression is a clinical term describing a phenomenon in which the electroencephalogram (EEG) of a sedated patient produces behavior that switches between higher frequency and amplitude bursting to lower frequency and lower amplitude suppression. This phenomenon can be observed during general anesthesia, hypothermia, or in an otherwise induced coma state. In a clinical setting, this phenomenon is typically induced by sedation from a drug such as propofol (2,6-diisopropylphenol). The level of sedation can be quantified by something called the burst suppression ratio (BSR), which is defined as the amount of time that a patient’s EEG is in a suppressed …

Digital, Automated Reactive Target System, Nicholas Haas, Saipranay Vellala, Trandon Ware, Thomas Martin

Williams Honors College, Honors Research Projects

In this era, technology is woven into almost every facet of our leisure activities. Although technology has innovated hobbies ranging from chess to soccer, the art of shooting has been neglected. Unnecessary insufficiency such as bullet ricochets off of mechanical steel targets, ineffective progress tracking, and general inaccessibility to outdoor training facilities are all improvable areas of this sport. The Dynamic Automated Reactive Target (D.A.R.T) System aims to fill some of these gaps and help modernize recreational marksmanship. Modeling the system after a dueling tree will optimize the use of the system and allow for different training models to challenge …

A Wearable Mechatronic Device For Hand Tremor Monitoring And Suppression: Development And Evaluation, Yue Zhou

Electronic Thesis and Dissertation Repository

Tremor, one of the most disabling symptoms of Parkinson's disease (PD), significantly affects the quality of life of the individuals who suffer from it. These people live with difficulties with fine motor tasks, such as eating and writing, and suffer from social embarrassment. Traditional medicines are often ineffective, and surgery is highly invasive and risky. The emergence of wearable technology facilitates an externally worn mechatronic tremor suppression device as a potential alternative approach for tremor management. However, no device has been developed for the suppression of finger tremor that has been validated on a human.

It has been reported in …

Sensor-Based Adaptive Control And Optimization Of Lower-Limb Prosthesis., Roozbeh Atri

FIU Electronic Theses and Dissertations

Recent developments in prosthetics have enabled the development of powered prosthetic ankles (PPA). The advent of such technologies drastically improved impaired gait by increasing balance and reducing metabolic energy consumption by providing net positive power. However, control challenges limit performance and feasibility of today’s devices. With addition of sensors and motors, PPA systems should continuously make control decisions and adapt the system by manipulating control parameters of the prostheses. There are multiple challenges in optimization and control of PPAs. A prominent challenge is the objective setup of the system and calibration parameters to fit each subject. Another is whether it …

Underwater Remotely Operated Vehicle Controller With Pid Stability Regulation, Christian E. Aguirre

Electrical Engineering

The earth’s oceans and rivers remain widely unexplored. Hobbyists and companies across the globe invest money and resources into remotely operated vehicles (ROV) to further expand underwater knowledge. Each ROV includes a controller that operates motors and monitors other crucial system vitals. The ROV Controller project makes the process of designing an ROV simpler and more affordable by providing a multi-purpose programmable controller.

The ROV controller features programmable digital inputs/outputs and analog inputs. The controller processes control signals from analog joysticks, digital signals from a gyroscope and utilizes a MUX to expand the analog input capabilities of the Arduino. The …

Torch Mounted Wire Nipper, Steven D. Patrick, Matt Montgomery, Ben Rouse, Garrett D. Foust

Chancellor’s Honors Program Projects

No abstract provided.

Physical Layer Discrimination Of Electronic Control Units Using Wired Signal Distinct Native Attribute (Ws-Dnda), Rahn M. Lassiter

Theses and Dissertations

The Controller Area Network (CAN) bus is a communication system used in automobiles to connect the electronic components required for critical vehicle operations. These components are called Electronic Control Units (ECU) and each one exercises one or more functions within the vehicle. ECUs can provide autonomous safety features and increased comfort to drivers but these advancements may come at the expense of vehicle security. Researchers have shown that the CAN bus can be hacked by compromising authorized ECUs or by physically connecting unauthorized devices to the bus. Physical layer (PHY) device fingerprinting has emerged as one of the accepted approaches …

Online Learning Of The Spatial-Temporal Channel Variation In Underwater Acoustic Communication Networks, Wensheng Sun

Dissertations, Master's Theses and Master's Reports

Influenced by environmental conditions, underwater acoustic (UWA) communication channels exhibit spatial and temporal variations, posing significant challenges for UWA networking and applications. This dissertation develops statistical signal processing approaches to model and predict variations of the channel and relevant environmental factors. Firstly, extensive field experiments are conducted in the Great Lakes region. Three types of the freshwater river/lake acoustic channels are characterized in the aspects of statistical channel variations and sound propagation loss, including stationary, mobile and under-ice acoustic channels. Statistical data analysis shows that relative to oceanic channels, freshwater river/lake channels have larger temporal coherence, higher correlation among densely …

Estimation And Prediction Of The Human Gait Dynamics For The Control Of An Ankle-Foot Prosthesis, Guilherme Aramizo Ribeiro

Dissertations, Master's Theses and Master's Reports

With the growing population of amputees, powered prostheses can be a solution to improve the quality of life for many people. Powered ankle-foot prostheses can be made to behave similar to the lost limb via controllers that emulate the mechanical impedance of the human ankle. Therefore, the understanding of human ankle dynamics is of major significance. First, this work reports the modulation of the mechanical impedance via two mechanisms: the co-contraction of the calf muscles and a change of mean ankle torque and angle. Then, the mechanical impedance of the ankle was determined, for the first time, as a multivariable …