Power and Energy Commons^™

Perovskite Solar Cells Fabricated Via Scalable Dip Coating Methods, Joseph F. Iannello

Theses and Dissertations

Perovskite solar cells present the possibility for less expensive electricity generation, through the use of low cost materials and fabrication methods relative to current silicon-based technology. Many current methods of fabricating thin film perovskite solar cells focus on spin-coating, which inherently lacks scalability due to particle conglomeration, poor uniformity over a larger area, and safety concerns. Dip-coating, an alternative to spin-coating, which is explored here addresses these issues which limit scalability. Each individual layer can be separately synthesized, deposited, and characterized, which leads towards scalability. Choosing only the best results from each independent layer allowed progress to the creation of …

Applications Of Artificial Intelligence In Power Systems, Samin Rastgoufard

LSU New Orleans Theses and Dissertations

Artificial intelligence tools, which are fast, robust and adaptive can overcome the drawbacks of traditional solutions for several power systems problems. In this work, applications of AI techniques have been studied for solving two important problems in power systems.

The first problem is static security evaluation (SSE). The objective of SSE is to identify the contingencies in planning and operations of power systems. Numerical conventional solutions are time-consuming, computationally expensive, and are not suitable for online applications. SSE may be considered as a binary-classification, multi-classification or regression problem. In this work, multi-support vector machine is combined with several evolutionary computation …

Tolerance Sensitivity Analysis And Robust Optimal Design Method Of A Surface-Mounted Permanent Magnet Motor By Using A Hybrid Response Surface Method Considering Manufacturing Tolerances, Cha-Seung Jun, Byung-Il Kwon, Ohbong Kwon

Publications and Research

This paper presents a robust optimal design method using a hybrid response surface method (H-RSM) which directly finds an optimal point satisfying a target Z-value or a probability of failure. Through three steps, this paper achieves the goal that is to increase the open-circuit airgap flux (OCAF) in a surface-mounted permanent magnet motor and decrease its variation caused by variations of the airgap lengths including an additional one between permanent magnets and rotor back yoke. First, the OCAF equation is derived from the magnetic equivalent circuit (MEC) considering the additional airgap. Then, the equation is validated by comparing its results …

Comparison Of Data Transfer Alternatives In Asynchronous Circuits, Mark Howard

Computer Science and Computer Engineering Undergraduate Honors Theses

Digital integrated circuits (ICs) have become progressively complex in their functionality. This has sped up the demand for asynchronous architectures, which operate without any clocking scheme, considering new challenges in the timing of synchronous systems. Asynchronous ICs have less stringent environmental constraints and are capable of maintaining reliable operation in extreme environments, while also enjoying potential benefits such as low power consumption, high modularity, and improved performance. However, when the traditional bus architecture of synchronous systems is applied to asynchronous designs, handshaking protocols required for asynchronous circuit operation result in significantly increased power consumption, offsetting the low power benefit of …

Scada And Plc Systems Configuration For The Ncrept Test Facility, Arman Ahmed

Electrical Engineering Undergraduate Honors Theses

This thesis details the project to update the control and interface system of the National Center for Reliable Electric Power Transmission (NCREPT) testing facility. The need for this project arose from the 2017-2018 expansion of the facility, which included some modifications in the layout of electrical equipment used for testing purposes. These modifications necessitated the update of the control and interface system. Additionally, the old system was implemented a decade ago and is nearing obsolescence, so the facility’s expansion served as an opportune time for an upgrade.

There were two main parts to the scope of this project, which were …

A Human Powered Micro-Generator For Charging Electronic Devices, John Adam

Senior Theses

A hand-pulled generator has been designed and tested. A preliminary result has been obtained and discussed. This device was created to provide outlet-free charging. Electronic devices are useful when going out into the wilderness. A portable power supply is necessary to keep an electronic device alive. This project created a device that converts human energy into electricity to charge electronic devices. This thesis overviews the device’s design, build, and tests. Two different tests were run to determine that the device is capable of charging the storage battery. The device presented can provide 14 minutes of charging time with one hour …

Increasing The Longevity Of Tungsten Filaments In A Zone Refiner, Byron D. Greenlee

Senior Theses

Zone refining is used for its ability to purify material and grow single crystals. To produce these single crystals, a suspended molten zone, generated by electron bombardment, passes along the polycrystalline stock. During a zone refining run, the filaments that produce the electron bombardment can fail. In this project, the longevity of tungsten filaments in a zone refiner was investigated. A new bombardment geometry was constructed to attempt to increase the longevity of the filaments. The new geometry had a shield machined into it to prevent line-of-sight impurities originating in the molten zone from striking the filaments. It was found …

Measuring The Double Layer Capacitance Of Electrolyte Solutions Using A Graphene Field Effect Transistor, Agatha Ulibarri

Senior Theses

When operating graphene field effect transistors (GFETs) in fluid, a double layer capacitance (C_dl) is formed at the surface. In the literature, the C_dl is estimated using values obtained using metal electrode experiments. Due to the distinctive electronic and surface properties of graphene, there is reason to believe these estimates are inadequate. This work seeks to directly characterize the double layer capacitance of a GFET. A unique method for determining the C_dl has been implemented, and data has been obtained for three electrolytes and one ionic fluid. The results yield dramatically lower C_dl values than …

Measuring The Double Layer Capacitance Of Electrolytes With Varied Concentrations, Geoffrey Rath

Senior Theses

When electric potentials are applied from an electrolytic fluid to a metal, a double layer capacitor, C_dl, develops at the interface. The layer directly at the interface is called the Stern layer and has a thickness equal to roughly the size of the ions in the fluid. The next layer, the diffuse layer, arises from the gathering of like charges in the Stern layer. This layer is the distance needed for ionic charges to return to equilibrium. This distance, called the Debye length, λ, depends on the square root of the electrolyte concentration. To study the properties of …

Lithium And The Foreseeable Future, Paolo Vargas

Mechanical Engineering Undergraduate Honors Theses

This paper aims to clarify the uncertainties regarding worldwide lithium resource availability in the years to come. Previous studies made on the subject are presented with some ambiguity and this work intends to fill the gaps. The information and data presented throughout this script with respect to global lithium resources and reserves are mostly based on data released by the United States Geological Survey (USGS). Lithium resource availability in the future is a point of paramount significance primarily for the automotive, portable electronics, and the power generation industry. Since, a change of supply would ultimately affect the price of lithium, …

Microgrids: Resilience, Reliability, And Market Structure, Saeed Dehghan Manshadi

Electrical Engineering Theses and Dissertations

This dissertation addresses several challenges corresponding to the operation and planning of microgrids in distribution networks including the formation, energy supply resilience, the contribution of microgrids in the short-term and mid-term operation of bulk power networks and the computational challenges in operation of interdependent infrastructure systems.

An approach to transforming the active distribution network with distributed energy resources into multiple autonomous microgrids is presented in the first section. The distribution network consists of several generation resources and demand entities that could be clustered into autonomous microgrids. Eigen decomposition in the graph spectra of the distribution network is leveraged to determine …

Grid-Connected Photovoltaic Systems Based On Nonlinear Control., Pablo R. Rivera

Electronic Theses and Dissertations

Nowadays, due to the high-scale penetration of photovoltaic systems, reliable and efficient grid-connected photovoltaic (PV) systems utilizing the advances of power electronics and control system technology are desirable. Thus, single-stage grid-connected photovoltaic systems, have gained attention, especially in low voltage applications. However, PV systems exhibit nonlinear behavior that could negatively affect the performance of the system if they are not adequately compensated for. In this dissertation, using the general structure for the synchronous dq0 frame, a single-stage three-phase grid-connected photovoltaic system, and a single-stage single-phase grid-connected PV system, both with a nonlinear control strategy, are developed to track the maximum …

Improving Operator Situation Awareness By Phasor Measurement Unit (Pmu) Data Visualization, Esa M. Rantanen, Ernest Fokoue, Jacob Haut, Chandini Ramesh, Kathleen Gegner, Thomas Overbye, Komal Shetye

Articles

The application of phasor measurement unit (PMU) data in the power industry is currently an area of intense interest. The key driver for PMU technology is to use the precise time sources provided by Global Positioning System (GPS) satellites to accurately measure the relative voltage and current phase angles at buses across an interconnect at a very high sampling rate. Presenting PMU data to power system operators in a format that is truly useful for them and that affords improved situation awareness (SA) and fast and accurate decision making is a particular challenge to display design. This report describes development …

Fabrication And Characterization Of Graphene Based 2d Materials For Supercapacitors, Anishkumar Manoharan

Graduate Theses and Dissertations

Supercapacitors have attracted a lot attention due to their efficient energy storage. In comparison to batteries, supercapacitors have high capacitance, energy, and power densities per unit mass than conventional capacitors. Carbon based materials are most promising in supercapacitor application due to their outstanding physical and electrochemical behavior. In this work, a facile method to synthesize a nanocomposite electrode consisting of annealed carbon from carbon ink and MoS2 was demonstrated. Effects of various aqueous and solid electrolytes were studied. It was found that the nanocomposite electrode with 10% MoS2 and 1M Na2SO4 as the aqueous electrolyte tested using the three electrode …

Gating Methods For High-Voltage Silicon Carbide Power Mosfets, Audrey Dearien

Graduate Theses and Dissertations

The objective of this thesis is to assess the challenges associated with driving Silicon Carbide (SiC) power devices, and to compare the potential gate drive methods for these devices which address those challenges. SiC power devices present many benefits that make them suitable for next generation automotive, power utility grid, and energy management applications. High efficiency, increased power density, and reliability at high-temperatures are some of the main benefits of SiC technology. However, the many challenges associated with these devices have prevented their adoption into industry applications. The argument is made in this thesis that the gate driver is a …

Protection, Automation, And Frequency Stability Analysis Of A Laboratory Microgrid System, Christopher Eric Osborn

Master's Theses

Due to increasing changes in the power industry, Cal Poly San Luis Obispo's electrical engineering department introduced a set of initiatives to adequately equip students with the skills and knowledge to interact with new technologies. Specifically, the department proposed a microgrid and power systems protection and automation laboratory to strengthen students' knowledge of microprocessor-based relays. This paper outlines a microgrid laboratory system that fulfills the initiative's goal and proposes a collection of laboratory experiments for inclusion in a new laboratory course at Cal Poly. The experiments provide students with practical experience using Schweitzer Engineering Laboratory (SEL) relays and teach fundamental …

Protection Against Ungrounded Single Phase Open Circuit Faults In 3-Phase Distribution Transformers, Higinio Ariel Montoya

Master's Theses

This thesis explores the impacts and behavior of 3-phase distribution transformers when subject to ungrounded single phase open circuit faults. A simple 3-phase system is modeled using MATLAB Simulink and operation under fault conditions are simulated and studied. Simulation results are confirmed via lab experimentation. Finally, a robust detection and protection method using neutral current injection (as proposed in industry literature) is built and demonstrated.

Electric utility operating experience has demonstrated that all too often, loads on 3-phase distribution transformers are not adequately protected against an ungrounded single phase open circuit fault (commonly called “single phasing”). This type of fault …

Synthesis And Electrochemical Properties Of Li3V2(Bo3)3/C Anode Materials For Lithium-Ion Batteries, You Wang, Yi-Wen Zeng, Xing Zhong, Xing Liu, Quan Tang

Journal of Electrochemistry

The Li₃V₂(BO₃)₃/C (LVB/C) composite materials were successfully synthesized in two steps:Firstly, a stoichiomertric mixture of Li₂C₂O₄, V₂O₅, H₃BO₃, H₂C₂O₄•H₂O and ethanol was thoroughly ball-milled to get the precursors. Secondly, the precursors were post-calcinated to get the ultimate products. The calcination temperatures of 750 ℃, 800 ℃ and 850 ℃ were selected based on TG-DTA analyses. The crystal structures, surface morphologies and carbon contents of the samples calcinated at five conditions, …

Preparation Of Ni(Dpim)2Cl2 Complex For The Electrocatalytic Reduction Of Co2, Li-Pu Zhang, Dong-Fang Niu, Xin-Sheng Zhang

Journal of Electrochemistry

A new Ni(dpim)₂Cl₂complex using 2-(diphenylphosphino)-1-methylimidazole (dpim) as ligand was prepared and served as a catalyst for the electrochemical reduction of CO₂. The electrochemical redox behavior of Ni(dpim)₂Cl₂ in CH₃CN/TPABF₄ solution under nitrogen atmosphere showed the two-electron irreversible reduction at -0.7 V and one-electron quasi-reversible reduction at -1.3 V. After bubbling CO₂ into the electrolyte, the reduction peak appeared at -1.3 V became irreversible and the peak current increased from 0.48 mA·cm^-2 to 0.55 mA·cm^-2. Moreover, the peak current at -1.3 V could further increase …

Preparation Of Co3O4/Ti Electrocatalytic Membrane Electrode For Catalytic Oxidation Of Benzyl Alcohol, Yu-Mei Zheng, Zhen Yin, Hong Wang, Jian-Xin Li

Journal of Electrochemistry

The cobalt oxide(Co₃O₄) nanoparticles were loaded on microporous Ti membrane to prepare Co₃O₄/Ti electrocatalytic membrane electrode by dip-coating method. The microstructures and electrochemical properties of Co₃O₄/Ti electrocatalytic membrane were investigated. The Co₃O₄/Ti electrocatalytic membrane reactor (ECMR) assembled by using the Co₃O₄/Ti electrocatalytic membrane as an anode was adopted for catalytic oxidation of benzyl alcohol to produce benzaldehyde and benzoic acid.The effects of different operation parameters on benzyl alcohol conversion, and selectivity to benzaldehyde and benzoic acid of ECMR were studied. …

Electrochemical Oxidation Of P-Chlorophenol On Porous Ti/Bdd Electrode Cooperated With Cathode Dechlorination, Rong-Ling Chen, Wei-Min Huang, Ya-Peng He, Jun Shi, Hai-Bo Lin

Journal of Electrochemistry

The electrochemical oxidation of p-chlorophenol on porous Ti/BDD electrode cooperated with synergistic effect of cathode dechlorination was studied. Electrochemical degradation tests of p-chlorophenol were conducted in single and double compartment electrolytic cells separately, and the results showed that the mineralization happened mainly in the anode region. The product of chloride ions produced from the cathodic reduction of 4-chlorophenol in the single cell migrated to the anode region and further generated active chlorine toward electro-catalytic oxidation. At the same time, the chloride ion produced from the cathode of the double cell was difficult to be migrated to the anode region, which …

Preparation And Properties Of Manganese Oxide And Polyaniline-Carbon Composite Electrode, Tian-Tian Zhou, Bing Wu, Chao Deng, Ying Gao

Journal of Electrochemistry

The polyaniline-carbon (PAnC) electrode was prepared by the polymerization of aniline monomer and activated carbon in ice water bath, and followed by chemical deposition of manganese dioxide MnO₂-PAnC composite material. The specific capacitance of MnO₂-PAnC reached 459 F•g^-1. The cyclic voltammetric results showed a small deformation in the voltammogram curve obtained with the MnO₂-PAnC electrode at high scan rate, indicating good reversibility and capacitive properties. The AC impedance results revealed that the MnO₂-PAnC electrode displayed the smallest charge transfer resistance and the fastest diffusion
rate of surface ions than other …

Simulation Analysis In Dynamic Performance Of Proton Exchange Membrane Fuel Cell Under Starting Condition, Yan Xiao, Ying-Jie Chang, Wei Zhang, Qiu-Hong Jia

Journal of Electrochemistry

Based on the equivalent circuit model, by considering both the dynamic gas pressure model and the dynamic heat transfer model, a lumped parameter model is developed. The start process of the fuel cell is simulated by using SIMULINK software. The undershoot of the voltage is observed from the simulation results, and the response time of the voltage is basically the same as that of the fuel cell temperature, which indicates that the temperature has great influence on the dynamic performance of the fuel cell. From the perspective of the temperature, the dynamic responses of the thermodynamic potential, the activation overvoltage, …

Interaction Between Energy And Electrocatalysis —— A Review On The 1st Young Scientist Forum On Energy Electrocatalysis, Hong Li, Wen-Bin Cai

Journal of Electrochemistry

No abstract provided.

Effects Of Rotating Magnetic Fields On Pem Fuel Cell Performance, Mao-Liang Wu, En-Ze Wang, Guang-De Pan, Zhong-Jun Liu, Fei Xie

Journal of Electrochemistry

Proton Exchange Membrane (PEM) fuel cell performance may be improved by application of additional magnetic fields. In this work, one square permanent magnet, made of either 16 combination cylinder magnets with homopolarity or 16 combination cylinder magnets with heteropolarity, was exerted on the fuel cell surface to produce additional magnetic field affecting PEM fuel cell performance. The influences of magnetic field status (rotating, static and none) on polarization and power density curves measured in a PEM fuel cell were investigated. The results verified the benefit of magnetic field, proving that the magnetic field distribution could improve the fuel cell output. …

Analysis Of Photovoltaic Energy In The Eastern Kentucky Region And The Residential Financial Feasibility, Joshua A. Johnson

Morehead State Theses and Dissertations

A thesis proposal presented to the Faculty of the College of Business and Technology Morehead State University in partial fulfillment of the requirements for the Degree Master of Science by Joshua A. Johnson on April 25, 2018.

Solid State Light Conversion, Jumana Turkistani

Honors Theses

Demand for innovative and energy-efficient technology has increased as an environmentally sustainable society has become priority. Technological development of solid-state light plays a part in meeting that demand. Our research has revealed that LED (Light Emitting Diode) lighting uses less energy and is a more cost effective and environmentally responsible choice than incandescent and fluorescent lighting. Converting from incandescent and fluorescent dominated lighting to LED lighting may be cumbersome but can result in a classroom milieu that is attractive, cost/energy effective, easy to manipulate as well as facilitative to learning. For this project, a small-scale mockup of the light fixtures …

Human Behavior Modeling For Residential Energy Consumption, Mesfer Alrizq

Research and Creative Activities Poster Day

Electric utility companies are interested in load profile (electricity consumption) data for expansion planning. Conventional methods of collecting the load profile data, such as surveys and metering, are tedious and time consuming activities. Cumbersome data collection processes also pose barriers. We present an innovative behavior model for generating electricity consumption load profiles. The model, based on fuzzy logic and activity graphs, requires minimum consumer data and can be easily updated to adapt to changes in technology. We demonstrate the accuracy of our model against real world data.

Advanced Modeling, Design, And Control Of Ac-Dc Microgrids, Hossein Saberi Khorzoughi

LSU Doctoral Dissertations

An interconnected dc grid that comprises resistive and constant-power loads (CPLs) that is fed by Photovoltaic (PV) units is studied first. All the sources and CPLs are connected to the grid via dc-dc buck converters. Nonlinear behavior of PV units in addition to the effect of the negative-resistance CPLs can destabilize the dc grid. A decentralized nonlinear model and control are proposed where an adaptive output-feedback controller is employed to stabilize the dc grid with assured stability through Lyapunov stability method while each converter employs only local measurements. Adaptive Neural Networks (NNs) are utilized to overcome the unknown dynamics of …

Considerations On Direct Balancing Of Ultra-High Power Ac Arc Furnaces In Uneasy State, Ikenna Louis Ezeonwumelu

LSU Master's Theses

During the operation of ultra-high-power ac arc furnace the negative effects of unbalance mostly occur in the secondary terminals of the transformer connected to the load. Hence balancing and compensating the furnace at this terminal will not only improve the transformer efficiency but also reduce energy losses that do occur. In this thesis a computer modeling of a reference ac arc furnace in both balanced and unbalanced states were simulated, and the effects of a reactive balancing compensator installed on the secondary side of the furnace transformer was evaluated to see how much delivered energy improvement can be obtained. The …