Power and Energy Commons^™

Optimal Sensing And Transmission In Energy Harvesting Sensor Networks, Xianwen Wu

Graduate Theses and Dissertations

Sensor networks equipped with energy harvesting (EH) devices have attracted great attentions recently. Compared with conventional sensor networks powered by batteries, the energy harvesting abilities of the sensor nodes make sustainable and environment-friendly sensor networks possible. However, the random, scarce and non-uniform energy supply features also necessitate a completely different approach to energy management.

A typical EH wireless sensor node consists of an EH module that converts ambient energy to electrical energy, which is stored in a rechargeable battery, and will be used to power the sensing and transmission operations of the sensor. Therefore, both sensing and transmission are subject …

High Step-Up/Down Transformerless Multilevel Converter For Renewable Energy Applications, Haider Ghazi Mhiesan

Graduate Theses and Dissertations

This thesis focuses on a high step-up/down transformerless dc-dc modular multilevel converter (MMC) that would be applicable to dc power systems. The design achieves high voltage ratios for interfacing renewable energy sources such as photovoltaic and line interactive Uninterruptible Power System (UPS) systems. The circuit topology provides for high step-up/down dc-dc conversion ratios using an MMC approach operating in resonant mode in order to improve overall efficiency. This topology operates to step-up the input voltage with 1:10 or larger conversion ratio. As a bidirectional converter, it also provides step-down capability at the same voltage ratio (10:1 or greater). The MMC …

Control Design Of A Single-Phase Dc/Ac Inverter For Pv Applications, Haoyan Liu

Graduate Theses and Dissertations

This thesis presents controller designs of a 2 kVA single-phase inverter for photovoltaic (PV) applications. The demand for better controller designs is constantly rising as the renewable energy market continues to rapidly grow. Some background research has been done on solar energy, PV inverter configurations, inverter control design, and hardware component selection. Controllers are designed both for stand-alone and grid-connected modes of operation. For stand-alone inverter control, the outer control loop regulates the filter capacitor voltage. Combining the synchronous frame outer control loop with the capacitor current feedback inner control loop, the system can achieve both zero steady-state error and …

Swat Model Simulation Of Bioenergy Crop Impacts On Water Quality In Cache River Watershed, Eeshan Kumar

Graduate Theses and Dissertations

Energy security through increased biofuel production is one of the components of the Energy Independence and Security Act (EISA) 2007. As per EISA 2007 mandate, appropriate independent research institutes are required to assess concerns to natural biodiversity due to biofuel production and report it to the Congress through the Environment Protection Agency (EPA). Planners, researchers, and agencies concerned with environmental regulations, ideally, would like to have location-specific information about the impacts for developing appropriate management interventions. This study examines long-term impacts on water quality in response to targeted (i.e. marginal lands) production of biofuel crops by setting up two SWAT …

Model Development And Validation For Wind Generation Transmission Systems, Mahmood Shihadeh Saadeh

Graduate Theses and Dissertations

In this research a new benchmark system is proposed for wind energy transmission systems. New model development, validation, and calibration methods for power transmission systems are proposed and implemented as well. First, a model reduction criteria is chosen based on electrical interconnection and geographical information. Model development is then done using reduction techniques on an operation model provided by a transmission operator based on the chosen criteria. Then model validation is performed using actual PMU synchrophasor measurements provided by a utility company. The model development and validation process ensures the accuracy of the developed model and makes for a realistic …

High-Frequency Transformer Design For Solid-State Transformers In Electric Power Distribution Systems, Roderick Javier Garcia Montoya

Graduate Theses and Dissertations

The objective of this thesis is to present a high- or medium-frequency transformer design methodology for Solid-State Transformer (SST) applications. SSTs have been proposed as a replacement of the traditional 50/60 Hz transformer in applications demanding high-power density. Moreover, due to the high penetration of distributed generation, DC grids, energy storage systems, and sensitive loads, SSTs have been considered as an enabling technology for envisioned future energy systems. These applications demand additional functionalities that may not be achieved with traditional transformers. For example, active power flow control, harmonic suppression, voltage regulation, voltage sag compensation, and reduced size and volume.

In …

High Temperature Silicon Carbide Mixed-Signal Circuits For Integrated Control And Data Acquisition, Ashfaqur Rahman

Graduate Theses and Dissertations

Wide bandgap semiconductor materials such as gallium nitride (GaN) and silicon carbide have grown in popularity as a substrate for power devices for high temperature and high voltage applications over the last two decades. Recent research has been focused on the design of integrated circuits for protection and control in these wide bandgap materials. The ICs developed in SiC and GaN can not only complement the power devices in high voltage and high frequency applications, but can also be used for standalone high temperature control and data acquisition circuitry.

This dissertation work aims to explore the possibilities in high temperature …

Broadband High Efficiency Fractal-Like And Diverse Geometry Silicon Nanowire Arrays For Photovoltaic Applications, Omar Hassan Al-Zoubi

Graduate Theses and Dissertations

Solar energy has many advantages over conventional sources of energy. It is abundant, clean and sustainable. One way to convert solar energy directly into electrical energy is by using the photovoltaic solar cells (PVSC). Despite PVSC are becoming economically competitive, they still have high cost and low light to electricity conversion efficiency. Therefore, increasing the efficiency and reducing the cost are key elements for producing economically more competitive PVSC that would have significant impact on energy market and saving environment. A significant percentage of the PVSC cost is due to the materials cost. For that, thin films PVSC have been …

Top-Down Aluminum Induced Crystallization For Photovoltaics, Seth Daniel Shumate

Graduate Theses and Dissertations

Passivating silicon solar cell surfaces is critical to fabricating very high efficiency and low cost photovoltaic devices. The sun-facing surface of the solar cell, known as the emitter, is particularly important when designing a solar cell. This work focused first on an alternative method of forming the emitter of silicon solar cells, and secondly on a method for improving the surface passivation of both these non-traditional and standard n-type solar cells.

Top-down aluminum induced crystallization (TAIC) was used for forming a polycrystalline silicon layer from amorphous silicon using aluminum to catalyze the crystallization at much lower temperatures than otherwise possible. …

Experimental Verification And Integration Of A Next Generation Smart Power Management System, Tavis Clemmer

Graduate Theses and Dissertations

With the increase in energy demand by the residential community in this country and the diminishing fossil fuel resources being used for electric energy production there is a need for a system to efficiently manage power within a residence. The Smart Green Power Node (SGPN) is a next generation energy management system that automates on-site energy production, storage, consumption, and grid usage to yield the most savings for both the utility and the consumer. Such a system automatically manages on-site distributed generation sources such as a PhotoVoltaic (PV) input and battery storage to curtail grid energy usage when the price …

Indirect Matrix Converter As Standard Power Electronic Interface, Andrés Escobar-Mejía

Graduate Theses and Dissertations

The increase in the penetration levels of distributed generation in the modern power grid and its importance in future energy systems have accelerated the interest of developing new power electronic interfaces for the energy conversion process. The feasibility of applying the indirect matrix converter as the standard power electronic interface for applications with power ratings from several kW to few MW is addressed in this dissertation. Special attention is given to those applications where space dominates the power electronic requirements. The main motivation for using the indirect matrix converter is that eliminates the energy storage component in the way of …

The Role Of Quantum Dot Size On The Performance Of Intermediate Band Solar Cells, Najla Alnami

Graduate Theses and Dissertations

The goal of this thesis is to understand possible mechanisms for the reported decrease of the open circuit voltage and solar cell efficiency in quantum dot (QD) intermediate band solar cells (IBSCs). More specifically, the effect of indium arsenide (InAs) QD height on the open circuit voltage and solar cell efficiency was studied in a systematic way. To explore this effect in QD solar cells, several solar cells (SCs) were grown with varying InAs QD heights. All experimental characteristics of the QD solar cells were compared to a reference structure without QDs. All samples were grown by Molecular Beam Epitaxy …

Photoelectric Characterization Of Bacteriorhodopsin Reconstituted In Lipid Bilayer Membrane, Joel Kamwa

Graduate Theses and Dissertations

The objective of this work was to conduct basic research in biologically inspired energy conversion solutions. A photosynthetic protein (Bacteriorhodopsin) was reconstituted in a bi-layer membrane. Then, when a laser beam was shined on the membrane, the photon energy was used by the protein to pump protons across the membrane. The translocation of protons across the membrane was measured as photocurrent. For this purpose, a system was built to characterize the lipid bilayer membranes and to measure the photocurrent. The lipid bilayer membrane was characterized by its capacitance and resistance. A picoampere photocurrent was observed when Bacteriorhodopsin protein was present …

Metal Assisted Nanowire Growth For Silicon Nanowire/Amorphous Silicon Composite Solar Cell, Asmaa Ali Sadoon

Graduate Theses and Dissertations

Solar cells are photovoltaic devices that convert the energy of light to electricity by the photovoltaic effect. Crystalline silicon-based solar cells are the most dominant solar cells in the market today due to the high efficiency and relatively low cost. However, the cost of such solar cell is still high due to the large amount of material that is consumed in fabricating such a device. Polycrystalline/amorphous thin films and nanomaterial technologies have emerged to reduce the high cost of c-Si based solar cells and increase the efficiency. In this research, we combined these two technologies to propose and fabricate silicon …

Life Cycle Assessment Projection Of Photovoltaic Cells: A Case Study On Energy Demand Of Quantum Wire Based Photovoltaic Technology Research, Shilpi Mukherjee

Graduate Theses and Dissertations

With increasing clean-energy demand, photovoltaic (PV) technologies have gained attention as potential long-term alternative to fossil fuel energy. However, PV research and manufacture still utilize fossil fuel-powered grid electricity. With continuous enhancement of solar conversion efficiency, it is imperative to assess whether overall life cycle efficiency is also being enhanced. Many new-material PV technologies are still in their research phase, and life cycle analyses of these technologies have not yet been performed. For best results, grid dependency must be minimized for PV research, and this can be accomplished by an analytical instrument called Life Cycle Assessment (LCA).

LCA is the …

Thermal Analysis, Parasitic Extraction, And Wirebond Reliability Studies Of Power Electronic Modules, Shilpa Prabhudeva

Graduate Theses and Dissertations

This thesis research investigates thermal performance, parasitic extraction and wirebond/encapsulation reliability of power electronic modules. Thermal performance is critical to the power electronic modules. As such, thermal analysis is an important part of the power electronic module design process. Several cases are studied on generalized power modules with a full bridge layout. A database is built based on these results. The studies are performed using SolidWorks thermal simulation tool. The database involves several parameters such as power dissipation, maximum junction temperature, ambient temperature, convection coefficient required to cool the module, size of the baseplate, heat-sink size, substrate size, spacing between …

Design Of System Level Control For A Residential Power Router, Fahad Hossain

Graduate Theses and Dissertations

This thesis presents the overall power flow and load management system for a 2 kW residential power router. The objective is to satisfy the residential load demand with cost savings by managing the energy sources including PV, battery, generator, and grid. The power flow management system algorithm is developed both for grid-connected mode and island mode. This algorithm involves the battery state of charge estimation, available PV power, load demand and electricity grid pricing. The residential load management algorithm is also developed using PV power prediction and load power prediction acquired for a day.¬ A Labview GUI is also developed …

Integration Of Energy Storage Into A Future Energy System With A High Penetration Of Distributed Photovoltaic Generation, Arthur K. Barnes

Graduate Theses and Dissertations

Energy storage units (ESU) are increasingly used in electrical distribution systems because they can perform many functions compared with traditional equipment. These include peak shaving, voltage regulation, frequency regulation, provision of spinning reserve, and aiding integration of renewable generation by mitigating the effects of intermittency.

As is the case with other equipment on electric distribution systems, it is necessary to follow appropriate methodologies in order to ensure that ESU are installed in a cost-effective manner and their benefits are realized. However, the necessary methodologies for integration of ESU have not kept pace with developments in both ESU and distribution systems. …

Unbalanced Current Static Compensator, Manuel Antonio Sanchez Tejada

Graduate Theses and Dissertations

The objective of this thesis is to present and evaluate a solution to the unbalanced current issue that can be found in three-phase electrical power grids. The solution is named unbalanced current static compensator (UCSC) and has the goal of balancing the currents at the source in order to mitigate adverse issues such as of negative- and zero-sequence currents that are generated by three-phase current unbalances.

The solution topology consists of three single-phase H-bridge converters that are controlled through an algorithm working in the d-q frame of reference. The algorithm is divided in three different stages: the phase synchronization and …

Broadband Nanostructured Antireflection Coating For Enhancing Inas/Gaas Quantum Dots Solar Cells Performance, Jony C. Sarker

Graduate Theses and Dissertations

The broadband suppression in reflection is one of the primary focuses in high efficiency solar cell research. In this thesis, a moth-eye inspired nanostructure antireflection coating is fabricated on InAs/GaAs quantum dots solar cell in order to enhance the power conversion efficiency. The abrupt refractive index transition between air and GaAs surface is replaced by a tapering zinc oxide nanoneedle on planar tantalum pentoxide coating. The antireflection structure provides gradual reduction of refractive index away from the solar cell top surface.

The nanostructured antireflection coating is fabricated by utilizing chemical bath deposition of tapered zinc oxide nanoneedles on planar tantalum …

Design, Fabrication And Characterization Of Plasmonic Fishnet Structures For The Enhancement Of Absorption In Thin Film Solar Cells, Sayan Seal

Graduate Theses and Dissertations

Incorporating plasmonic structures into the back spacer layer of thin film solar cells (TFSCs) is an efficient way to improve their performance. The fishnet structure; which is a tunable, plasmonic light scatterer is used to enhance light absorption. Unlike other plasmonic particles that have been previously suggested, the fishnet is an electrically connected wire mesh and does not result in electric field localization, hence it results in greater absorption in the intrinsic Si layer. Unlike other designs, the fishnet structure is placed in the back spacer layer of the TFSC, so it does not block any incident light. There is …

Electrical Design Considerations And Packaging Of Power Electronic Modules, Shijie Wang

Graduate Theses and Dissertations

A modern power electronic module can save significant energy usage in the power electronic systems by improving their switching efficiencies. One way to improve the efficiency of the power electronic module is to reduce its parasitic circuit elements. The purpose of this thesis is to investigate the mitigation of parasitic circuit elements in power electronic modules. General methods of mitigating parasitic inductances were analyzed by the Q3D Extractor and verified by the time-domain reflectometry (TDR) measurements. In most cases, the TDR measurement results closely matched those predicted by the Q3D Extractor. These methods were applied to design and analyze a …

Intermediate Band Solar Cells Based On Inas Quantum Dots Embedded In Ingaas Quantum Well, Ramesh Vasan

Graduate Theses and Dissertations

Intermediate band solar cells based on quantum dots and quantum wells with anti-reflection coating are investigated in this thesis. The demand for high efficient solar cells as an alternate source of energy is the main motivation for this research project. Intermediate band solar cells based on quantum dots were the subject of intensive research in recent years. High power conversion efficiency was predicted from InAs/GaAs intermediate band solar cells as the presence of InAs quantum dots increased the absorption below the band gap of the host material.

In this thesis, an attempt has been made to further increase the absorption …

Design, Layout, And Testing Of A Silicon Carbide-Based Under Voltage Lock-Out Circuit, Michael Dalan Glover

Graduate Theses and Dissertations

Silicon carbide-based power devices play an increasingly important role in modern power conversion systems. Finding a means to reduce the size and complexity of these systems by even incremental amounts can have a significant impact on cost and reliability. One approach to achieving this goal is the die-level integration of gate driver circuitry with the SiC power devices. Aside from cost reductions, there are significant advantages to the integration of the gate driver circuits with the power devices. By integrating the gate driver circuitry with the power devices, the parasitic inductances traditionally seen between the gate driver and the switching …

Synthesis Of Optimized Inp/Zns Core/Shell Nanocrystals And Tio2 Nanotubes For Quantum Dot Sensitized Solar Cells, Seungyong Lee

Graduate Theses and Dissertations

Synthesis of InP/ZnS core/shell nanocrystals and TiO₂ nanotubes and the optimization study to couple them together were explored for quantum dot sensitized solar cells. Its intrinsic nontoxicity makes the direct band gap InP/ZnS core/shell be one of the most promising semiconductor nanocrystals for optoelectric applications, with the advantage of tuning the optical absorption range in the desired solar spectrum region. Highly luminescent and monodisperse InP/ZnS nanocrystals were synthesized in a non-coordinating solvent. By varying the synthesis scheme, different size InP/ZnS nanocrystals with emission peaks ranging from 520 nm to 620 nm were grown. For the purpose of ensuring air …

Performance And Cost Analysis Of A Structured Concrete Thermocline Thermal Energy Storage System, Matt Nicholas Strasser

Graduate Theses and Dissertations

Increasing global energy demands and diminishing fossil fuel resources have raised increased interest in harvesting renewable energy resources. Solar energy is a promising candidate, as sufficient irradiance is incident to the Earth to supply the energy demands of all of its inhabitants. At the utility scale, concentrating solar power (CSP) plants provide the most cost-efficient method of harnessing solar energy for conversion to electrical energy. A major roadblock to the large-scale implementation of CSP plants is the lack of thermal energy storage (TES) that would allow the continued production of electricity during the absence of constant irradiance. Sensible heat TES …

Thermal And Electrical Parasitic Modeling For Multi-Chip Power Module Layout Synthesis, Zihao Gong

Graduate Theses and Dissertations

This thesis presents thermal and electrical parasitic modeling approaches for layout synthesis of Multi-Chip Power Modules (MCPMs). MCPMs integrate power semiconductor devices and drive electronics into a single package. As the switching frequency of power devices increases, the size of the passive components are greatly reduced leading to gains in efficiency and cost reduction. In order to increase switching frequency, electrical parasitics in MCPMs need to be reduced through tighter electronic integrations and smaller packages. As package size is decreased, temperature increases due to less heat dissipation capability. Thus, it is crucial to consider both thermal and electrical parasitics in …

Optimization Of Nonlinear Switch Cells For Switching Converters, Bradley Alan Reese

Graduate Theses and Dissertations

Switch cells consist of an array of power switches and passive components which can replace the main switches alone in many power topologies, allowing reduced switching loss without altering the power topology directly. This thesis discusses the development of a switch cell topology that utilizes a saturable resonant inductor to reduce the size and power loss of the cell. Additionally, the cell transfers energy stored in the inductor into a capacitor for efficient energy storage during the cell's conduction region. This energy is then transferred back to the system when the cell turns off, thus reducing the total switching energy.

Fabrication Of Composite Nanomaterials For Thin Film Amorphous Silicon Solar Cells, Benjamin Seth Newton

Graduate Theses and Dissertations

A material with the precise combination of amorphous silicon and polycrystalline silicon would be able to take advantage of the high absorption capabilities of amorphous silicon and the electron transport capabilities of polycrystalline silicon. Polycrystalline nanostructures in the form of wires can also take advantage of other properties of light absorption, trapping and scattering inherent in nanowire structures. These properties of high absorption and electron transport in one device would lead to advances in the search for highly efficient low cost solar cells and sensors. In this work a thin film material composed of an array of polycrystalline silicon nanostructures …