Power and Energy Commons^™

A Double-Sided Stack Low-Inductance Wire-Bondless Sic Power Module With A Ceramic Interposer, Si Huang

Graduate Theses and Dissertations

The objective of this dissertation research is to develop a novel three-dimensional (3-D) wire bondless power module package for silicon carbide (SiC) power devices to achieve a low parasitic inductance and an improved thermal performance. A half-bridge module consisting of 900-V SiC MOSFETs is realized to minimize stray parasitic inductance as well as to provide both vertical and horizontal cooling paths to maximize heat dissipation. The proposed 3-D power module package was designed, simulated, fabricated and tested. In this module, low temperature co-fired ceramic (LTCC) substrate with vias is utilized as an interposer of which both top and bottom sides …

Use Of The Igbt Module In The Active Region To Design A High Current Active Filter, Jorge F. Galarraga

Graduate Theses and Dissertations

Particle accelerators require high-precision magnetic fields on the order or 100ppm or less. This implies that the precision of the associated electrical current in the electromagnet that generates these fields should be smaller than 100ppm. However, conventional switching power supplies cannot offer this precision due to the frequency limitation of the switches. This research considers the use of power electronics devices operating in a linear as an alternative solution to meet the requirements of particle accelerator electromagnets.

This thesis presents the study of an insulated-gate bipolar transistor (IGBT) driver using a new control method that linearizes the IGBT’s collector-emitter voltage …

Design And Validation Of A High-Power, High Density All Silicon Carbide Three-Level Inverter, Zhongjing Wang

Graduate Theses and Dissertations

Transportation electrification is clearly the road toward the future. Compared to internal combustion engine, the electrified vehicle has less carbon-dioxide emission, less maintenance costs and less operation costs. It also offers higher efficiency and safety margin. More importantly, it relieves human’s dependence on conventional fossil energy. In the electrification progress, the revolution of electric traction drive systems is one of the most important milestone. The traction system should keep high efficiency to avoid performance reduction. Moreover, the motor drive should be designed within limited space without sacrificing output power rating. Based on the road map from US Drive Electrical and …

Direct Torque Control For Silicon Carbide Motor Drives, Mohammad Hazzaz Mahmud

Graduate Theses and Dissertations

Direct torque control (DTC) is an extensively used control method for motor drives due to its unique advantages, e.g., the fast dynamic response and the robustness against motor parameters variations, uncertainties, and external disturbances. Using higher switching frequency is generally required by DTC to reduce the torque ripples and decrease stator current total harmonic distortion (THD), which however can lower the drive efficiency. Through the use of the emerging silicon carbide (SiC) devices, which have lower switching losses compared to their silicon counterparts, it is feasible to achieve high efficiency and low torque ripple simultaneously for DTC drives.

To overcome …

Si-Based Germanium Tin Photodetectors For Infrared Imaging And High-Speed Detection, Huong Tran

Graduate Theses and Dissertations

Infrared (IR) radiation spans the wavelengths of the windows: (1) near-IR region ranging from 0.8 to 1.0 μm, (2) shortwave IR (SWIR) ranging from 1.0 to 3.0 μm, (3) mid-wave IR (MWIR) region covering from 3.0 to 5.0 μm, (4) longwave IR (LWIR) spanning from 8.0 to 12.0 μm, and (5) very longwave IR extending beyond 12.0 μm. The MWIR and LWIR regions are important for night vision in the military, and since the atmosphere does not absorb at these wavelengths, they are also used for free-space communications and astronomy. Automotive and defect detection in the food industry and electronic …

An Accurate And Efficient Electro-Thermal Compact Model Of Sic Power Mosfet Including Third Quadrant Behavior, Arman Ur Rashid

Graduate Theses and Dissertations

Due to narrower bandgap and lower critical electric field, silicon (Si) power devices have reached their limit in terms of the maximum blocking voltage capability. Exploiting this limitation, wide bandgap devices, namely silicon carbide (SiC) and gallium nitride (GaN) devices, are increasingly encroaching on the lucrative power electronics market. Unlike GaN, SiC devices can exploit most of the established fabrication techniques of Si power devices. Having substrate of the same material, vertical device structures with higher breakdown capabilities are feasible in SiC, unlike their GaN counterpart. Also, the excellent thermal conductivity of SiC, compared to GaN and Si, let SiC …

Design Of A 350 Kw Silicon Carbide Based 3-Phase Inverter With Ultra-Low Parasitic Inductance, Matthew Feurtado

Graduate Theses and Dissertations

The objective of this thesis is to present a design for a low parasitic inductance, high power density 3-phase inverter using silicon-carbide power modules for traction application in the electric vehicles with a power rating of 350 kW. With the market share of electric vehicles continuing to grow, there is a great opportunity for wide bandgap semiconductors such as silicon carbide (SiC) to improve the efficiency and size of the motor drives in these applications. In order to accomplish this goal, careful design and selection of each component in the system for optimum performance from an electrical, mechanical, and thermal …

High-Temperature Optoelectronic Device Characterization And Integration Towards Optical Isolation For High-Density Power Modules, Syam Madhusoodhanan

Graduate Theses and Dissertations

Power modules based on wide bandgap (WBG) materials enhance reliability and considerably reduce cooling requirements that lead to a significant reduction in total system cost and weight. Although these innovative properties lead power modules to higher power density, some concerns still need to be addressed to take full advantage of WBG-based modules. For example, the use of bulky transformers as a galvanic isolation system to float the high voltage gate driver limits further size reduction of the high-temperature power modules. Bulky transformers can be replaced by integrating high-temperature optocouplers to scale down power modules further and achieve disrupting performance in …

Growth And Characterization Of Semiconductor Materials And Devices For Extreme Environments Applications, Abbas Sabbar

Graduate Theses and Dissertations

Numerous industries require electronics to operate reliably in harsh environments, such as extreme high temperatures (HTs), low temperature (LT), radiation rich environments, multi-extreme, etc. This dissertation is focused on two harsh environments: HT and multi-extreme.

The first study is on HT optoelectronics for future high-density power module applications. In the power modules design, galvanic isolation is required to pass through the gate control signal, reject the transient noise, and break the ground loops. The optocoupler, which consists of a lighting emitting diode (LED) and photodetector (PD), is commonly used as the solution of galvanic isolation at room temperatures. There is …

High Frequency Ltcc Based Planar Transformer, Adithya Venkatanarayanan

Graduate Theses and Dissertations

As we move towards high power and higher frequency related technology, conventional wire-wound magnetics have their own limitations which has led path to the development of planar based magnetic materials. Nowadays more planar magnetic technology has been employed because it is easier to fabricate them. The planar magnetic is a transformer or an inductor that replaces the wire-wound transformer or inductors which generally uses copper wires. One of the main reasons why we move to planar magnetic technology is its operation at higher frequency which provides higher power density. This study explains in detail about the design and fabrication of …

Design And Optimization Of A High Power Density Silicon Carbide Traction Inverter, Tyler Adamson

Graduate Theses and Dissertations

This project was initiated with the goal of demonstrating a 3-phase silicon carbide based 150-kW 25 kW/L DC-AC power conversion unit capable of operation with coolant temperatures up to 90°C. The project goals were met and exceeded by first analyzing the established inverter topologies to find which one would yield the highest power density while still meeting electrical performance needs in the 150-kW range. Following topology selection, the smallest silicon carbide power module that met the electrical requirements of the system was found through experimental testing and simulation. After a power module selection was finalized, a DC link capacitor bank …

Five-Level Flying Capacitor Converter Used As A Static Compensator For Current Unbalances In Three-Phase Distribution Systems, Rafael Franceschi

Graduate Theses and Dissertations

This thesis presents and evaluates a solution for unbalanced current loading in three-phase distribution systems. The proposed solution uses the flying capacitor multilevel converter as its main topology for an application known as Unbalanced Current Static Compensator. The fundamental theory, controller design and prototype construction will be presented along with the experimental results. The Unbalanced Current Static Compensator main objective is the balancing of the up-stream currents from the installation point to eliminate the negative- and zero-sequence currents originated by unbalanced single-phase loads.

Three separate single-phase flying capacitor converters are controlled independently using a d-q rotating reference frame algorithm to …

Synchrophasor-Based Fault Location Detection And Classification, In Power Systems, Using Artificial Intelligence, Hemal Falak

Graduate Theses and Dissertations

With the introduction of sophisticated electronic gadgets which cannot sustain interruption in the provision of electricity, the need to supply uninterrupted and reliable power supply, to the consumers, has become a crucial factor in the present-day world. Therefore, it is customary to correctly identify fault locations in an electrical power network, in order to rectify faults and restore power supply in the minimum possible time. Many automated fault location detection algorithms have been proposed, however, prior art requires topological and physical information of the electrical power network. This thesis presents a new method of detecting fault locations, in transmission as …

A Silicon Germanium Cmos Linear Voltage Regulator For Wireless Agricultural Applications, Aminta Naidili Castillo Robles

Graduate Theses and Dissertations

This thesis presents the design, simulation and test results of a silicon germanium (SiGe) complementary metal-oxide-semiconductor (CMOS) linear regulator. The objective of the circuit is to power other analog devices regardless of the load current and input voltage changes. The application of this regulator is to be part of a project developing a miniaturized semiconductor platform that can be inserted into stems of crops in order to measure data inside the plant and then send it wirelessly to the user. The linear regulator was designed on a BiCMOS SiGe 0.13µm which is a GlobalFoundries process. It has been tested at …

Model Development And Assessment Of The Gate Network In A High-Performance Sic Power Module, William Austin Curbow

Graduate Theses and Dissertations

The main objective of this effort is to determine points of weakness in the gate network of a high-performance SiC power module and to offer remedies to these issues to increase the overall performance, robustness, and reliability of the technology. In order to accomplish this goal, a highly accurate model of the gate network is developed through three methods of parameter extraction: calculation, simulation, and measurement. A SPICE model of the gate network is developed to analyze four electrical issues in a high-speed, SiC-based power module including the necessary internal gate resistance for damping under-voltage and over-voltage transients, the disparity …

Comparative Study Of Power Semiconductor Devices In A Multilevel Cascaded H-Bridge Inverter, Kenneth Mordi

Graduate Theses and Dissertations

This thesis compares the performance of a nine-level transformerless cascaded H-bridge (CHB) inverter with integrated battery energy storage system (BESS) using SiC power MOSFETs and Si IGBTs. Two crucial performance drivers for inverter applications are power loss and efficiency. Both of these are investigated in this thesis. Power devices with similar voltage and current ratings are used in the same inverter topology, and the performance of each device is analyzed with respect to switching frequency and operating temperature. The loss measurements and characteristics within the inverter are discussed. The Saber® simulation software was used for the comparisons. The power MOSFET …

Investigation Of A Gan-Based Power Supply Topology Utilizing Solid State Transformer For Low Power Applications, Akrem Mohamed Elrajoubi

Graduate Theses and Dissertations

Gallium nitride (GaN) power devices exhibit a much lower gate capacitance for a similar on-resistance than its silicon counterparts, making it highly desirable for high-frequency operation in switching converters, which leads to their significant benefits on power density, cost, and system volume. High-density switching converters are being realized with GaN power devices due to their high switching speeds that reduce the size of energy-storage circuit components. The purpose of this dissertation research is to investigate a new isolated GaN AC/DC switching converter based on solid-state transformer configuration with a totem-pole power factor corrector (PFC) front-end, a half-bridge series-resonant converter (SRC) …

The Development Of Novel Interconnection Technologies For 3d Packaging Of Wire Bondless Silicon Carbide Power Modules, Sayan Seal

Graduate Theses and Dissertations

This dissertation advances the cause for the 3D packaging and integration of silicon carbide power modules. 3D wire bondless approaches adopted for enhancing the performance of silicon power modules were surveyed, and their merits were assessed to serve as a vision for the future of SiC power packaging. Current efforts pursuing 3D wire bondless SiC power modules were investigated, and the concept for a novel SiC power module was discussed. This highly-integrated SiC power module was assessed for feasibility, with a focus on achieving ultralow parasitic inductances in the critical switching loops. This will enable higher switching frequencies, leading to …

Reduction In Recombination Current Density In Boron Doped Silicon Using Atomic Hydrogen, Matthew Garett Young

Graduate Theses and Dissertations

The solar industry has grown immensely in recent years and has reached a point where solar energy has now become inexpensive enough that it is starting to emerge as a mainstream electrical generation source. However, recent economic analysis has suggested that for solar to become a truly wide spread source of electricity, the costs still need to plummet by a factor of 8x. This demands new and innovative concepts to help lower such cost. In pursuit of this goal, this dissertation examines the use of atomic hydrogen to lessen the recombination current density in the boron doped region of n-type …

High Temperature Silicon Carbide Mixed-Signal Circuits For Integrated Control And Data Acquisition, Ashfaqur Rahman

Graduate Theses and Dissertations

Wide bandgap semiconductor materials such as gallium nitride (GaN) and silicon carbide have grown in popularity as a substrate for power devices for high temperature and high voltage applications over the last two decades. Recent research has been focused on the design of integrated circuits for protection and control in these wide bandgap materials. The ICs developed in SiC and GaN can not only complement the power devices in high voltage and high frequency applications, but can also be used for standalone high temperature control and data acquisition circuitry.

This dissertation work aims to explore the possibilities in high temperature …

Indirect Matrix Converter As Standard Power Electronic Interface, Andrés Escobar-Mejía

Graduate Theses and Dissertations

The increase in the penetration levels of distributed generation in the modern power grid and its importance in future energy systems have accelerated the interest of developing new power electronic interfaces for the energy conversion process. The feasibility of applying the indirect matrix converter as the standard power electronic interface for applications with power ratings from several kW to few MW is addressed in this dissertation. Special attention is given to those applications where space dominates the power electronic requirements. The main motivation for using the indirect matrix converter is that eliminates the energy storage component in the way of …

Design, Fabrication And Characterization Of Plasmonic Fishnet Structures For The Enhancement Of Absorption In Thin Film Solar Cells, Sayan Seal

Graduate Theses and Dissertations

Incorporating plasmonic structures into the back spacer layer of thin film solar cells (TFSCs) is an efficient way to improve their performance. The fishnet structure; which is a tunable, plasmonic light scatterer is used to enhance light absorption. Unlike other plasmonic particles that have been previously suggested, the fishnet is an electrically connected wire mesh and does not result in electric field localization, hence it results in greater absorption in the intrinsic Si layer. Unlike other designs, the fishnet structure is placed in the back spacer layer of the TFSC, so it does not block any incident light. There is …

Electrical Design Considerations And Packaging Of Power Electronic Modules, Shijie Wang

Graduate Theses and Dissertations

A modern power electronic module can save significant energy usage in the power electronic systems by improving their switching efficiencies. One way to improve the efficiency of the power electronic module is to reduce its parasitic circuit elements. The purpose of this thesis is to investigate the mitigation of parasitic circuit elements in power electronic modules. General methods of mitigating parasitic inductances were analyzed by the Q3D Extractor and verified by the time-domain reflectometry (TDR) measurements. In most cases, the TDR measurement results closely matched those predicted by the Q3D Extractor. These methods were applied to design and analyze a …

Fabrication Of Composite Nanomaterials For Thin Film Amorphous Silicon Solar Cells, Benjamin Seth Newton

Graduate Theses and Dissertations

A material with the precise combination of amorphous silicon and polycrystalline silicon would be able to take advantage of the high absorption capabilities of amorphous silicon and the electron transport capabilities of polycrystalline silicon. Polycrystalline nanostructures in the form of wires can also take advantage of other properties of light absorption, trapping and scattering inherent in nanowire structures. These properties of high absorption and electron transport in one device would lead to advances in the search for highly efficient low cost solar cells and sensors. In this work a thin film material composed of an array of polycrystalline silicon nanostructures …