Power and Energy Commons^™

Design And Optimization To Advance Silicon Carbide Modules For Medium Voltage High Power Applications, Ahmed Ismail

Graduate Theses and Dissertations

The commercial availability of the first 10 kV silicon carbide (SiC) MOSFET removes the principal semiconductor barrier to medium-voltage power conversion, enabling converter topologies that are structurally inaccessible to silicon IGBT solutions at this voltage class. This dissertation presents the characterization infrastructure, device-level data, and preliminary system-level validation needed to advance the deployment of the third-generation 10 kV SiC MOSFET in converter applications. A custom-built 10 kV double-pulse test platform is developed with a fully documented component-sizing methodology, custom medium-voltage magnetics, and a measurement infrastructure capable of high bandwidth waveform capture at kilovolt common-mode potentials. On this platform, the third-generation …

Study And Simulation Of Model-Reference Adaptive Control Via The Heffron-Philips Model For Enhanced Power System Stability, Laila Ayman Dallol

Graduate Theses and Dissertations

Improving power transmission and quality has been an area of research interest over the past decades and was improved using renewable energy resources, mainly wind, and solar generation. Renewable energy penetration into power grids aims to replace some traditional synchronous generators, affecting the overall power system with reduced gas emissions that help with climate change and pollution issues. However, renewable generation in power systems ranging from microgrids to national grids is subjected to large disturbances that affect its transient stability, which is measured by its critical clearing time. As increased amounts of renewable generation connected to power systems have resulted …

Implementation Of A Three-Port Solar Converter With A Battery Energy Storage System, Maison Christopher Phipps

Graduate Theses and Dissertations

The increasing deployment of distributed solar and energy storage systems has created the need for integrated power converters that can efficiently manage photovoltaic (PV) generation, battery energy storage, and grid-tied AC output. This thesis presents the implementation and validation of a 5kW non-isolated Three-Port Converter (TPC) adapted for residential solar applications. The converter consolidates three power stage into a high-frequency, compact architecture: a unidirectional boost converter for PV input, a bidirectional interleaved buck-boost converter for battery energy storage, and a configurable DC/AC inverter for 120Vac single-phase output. The system is controlled using a central controller implemented on a TI C2000™ …

Design And Optimization Of High-Frequency Medium-Voltage Dual Active Bridge Dc/Dc Converter Using Sic Device, Hui Cao

Graduate Theses and Dissertations

High frequency Dual Active Bridge (DAB) converters have become a key enabling technology in medium- and high-power applications such as renewable energy integration, electric vehicle fast charging, and emerging DC power distribution systems. However, when operating at high power and high frequency, DAB converters face critical challenges including limited soft-switching range, uneven semiconductor loss distribution, deadtime-induced resonance, switching-frequency constraints of wide-bandgap (WBG) devices, and transformer DC bias during dynamic transitions. This dissertation addresses these challenges through advancements in modulation strategies and converter architecture. First, an enhanced triple-phase-shift (E-TPS) modulation scheme is proposed to achieve balanced switching and conduction losses across …

Solar Powered Conservation: The Effects Of Solar Photovoltaic Facilities On Avian Community Composition, Michael Christopher Ferrara

Graduate Theses and Dissertations

The expansion of solar photovoltaic energy infrastructure is transforming landscapes worldwide. Increasingly, facilities are planted with native vegetation, yet how vegetation characteristics and landscape variables shape wildlife communities in solar facilities remains poorly understood. Because avian populations have been in decline and are sensitive to habitat changes, understanding how solar facilities influence avian communities is important. In Chapter 1, we used autonomous recording units, local vegetation measurements, and land use and land cover data to quantify how avian community occupancy is influenced by solar cover in solar facilities and comparable reference sites. We used a Bayesian multi-species occupancy model to …

High-Power Power Conditioning Systems For Medium-Voltage Applications, Ahmed Rahouma Fares Rahouma

Graduate Theses and Dissertations

The purpose of this dissertation is to address the background, theoretical analyses, design methodologies, and evaluation techniques relevant to high-power power conditioning systems (PCSs) tailored for medium-voltage (MV) applications. Conventional PCSs, reliant on line-frequency transformers (LFTs), suffer from many problems including low power densities, inflexible designs, and scalability constraints. Employing multilevel converters (MLCs), particularly cascaded H-bridge topology, eliminates the need for these LFTs. A key focus lies in minimizing the number of cascaded building blocks by harnessing MV power switching modules. The dissertation makes two primary contributions: firstly, it offers a design methodology for MV-PCS, facilitating the selection of the …

Evaluation, Modeling And Application Of Gallium Nitride Field Effect Transistor, Geno Guillaume

Graduate Theses and Dissertations

Gallium Nitride (GaN) has emerged as one of the leading materials for power devices due to its wide band gap and high electron mobility. The band gap is the minimum energy required to excite an electron up to a state in the conduction band where it can participate in conduction. Because of this, wide band gap (WBG) materials are favorable for various electrical applications. The market for GaN high-electron-mobility transistor (HEMT) is projected to exceed $1.25 billion by 2027. With the increase of market interest, modern technologies emerge that aim to push the boundaries of efficiency for GaN power devices. …

A 10 Kv Sic Mosfet Power Module With Optimized System Interface And Electric Field Distribution, Xiaoling Li

Graduate Theses and Dissertations

This dissertation introduces a holistic and systematic design methodology tailored to the 10 kV silicon carbide (SiC) MOSFET power modules to achieve multi-objective optimization with enhanced electric-field (E-field) distribution, minimized common-mode (CM) parasitic capacitance, and reduced system-level parasitic inductances. The proposed approach encompasses two innovative techniques: 1) an electric-potential-oriented module-system interface to reduce system-level parasitic inductance while maximizing insulation capability; 2) stacked substrates with patterned middle layer copper to alleviate the E-field concentration at the triple-point and reduce the maximum E-field without compromising on thermal resistance. The effectiveness of these innovative approaches is substantiated through the development of a 10 …

High Bandwidth Hybrid Current Sensor Readout Interface For Power Applications, Asma Mahar

Graduate Theses and Dissertations

High-density and power-efficient circuits have become realizable with the advent of wide bandgap semiconductor devices due to their high switching speed and lower conduction/switching losses. The operation of these circuits requires current information for protection, monitoring, and control. For the realization and a further boost in the efficiency of such power circuits, small size, non-invasive, high bandwidth current sensors with noise immunity, accuracy, and linearity are required. Various hybrid sensors have been reported to meet the requirements of emerging power circuits. A combination of a magneto resistor or Hall sensor and a coil is used to cover a wide frequency …

High Performance Silicon Carbide Based Converters For Powertrain Electrification, Nan Lin

Graduate Theses and Dissertations

With the increasing concern towards environment protection, electric vehicles (EVs) and hybrid electric vehicles (HEVs) have become popular in recent years. They not only help reduce carbon emissions, but also come with other benefits such higher efficiency and better user experience. Many countries and vehicle manufactures have made their plans to keep up with this trend in vehicle electrification. Powertrain is an assembly of components in a vehicle that pushes it forward. As for EVs and HEVs, their powertrains are composed of one or more power electronics converters, which are significant to the system. Silicon carbide MOSFETs have shown superior …

Design And Implementation Of High-Frequency Dc-Dc Converters For Ev Applications, Rahul Biswash

Graduate Theses and Dissertations

The power electronics industry has been revolutionized by introducing wide bandgap semiconductor devices, such as Silicon Carbide (SiC) and Gallium Nitride (GaN). Due to their high frequency, high temperature, and high voltage operating capabilities, wide bandgap devices boast significant improvements in power density, efficiency, and reliability, as evidenced by their ability to decrease the size of power converters by operating at higher frequencies, temperatures and voltages, use of smaller and less passive components, such as transformers, inductors and capacitors, which makes power converters more compact and light-weight, ideal for space and weight-constrained applications, and compatibility with a wide range of …

High-Power Dc-Dc Transformer For Medium-Voltage Grids With High-Voltage Sic Technology, Roderick Gomez

Graduate Theses and Dissertations

The objective of this dissertation is to present the theoretical analysis, design process, application and manufacturing of a proposed solid-state transformer intended for medium-voltage applications with minimal high-frequency oscillations. Galvanic isolation on medium-voltage DC-DC converters tend to employ large number of turns in the high voltage side of the transformers leading to non-negligible parasitic stray capacitances which form resonance tanks with the transformer inductances. Therefore, it is critical to estimate these parasitic capacitances to avoid severe high frequency oscillations which can significantly impact the converter performance. The main contribution of this thesis is the extension of a proposed custom-core design …

Ism-Band Energy Harvesting Wireless Sensor Node, Fnu Naveed

Graduate Theses and Dissertations

In recent years, the interest in remote wireless sensor networks has grown significantly, particularly with the rapid advancements in Internet of Things (IoT) technology. These networks find diverse applications, from inventory tracking to environmental monitoring. In remote areas where grid access is unavailable, wireless sensors are commonly powered by batteries, which imposes a constraint on their lifespan. However, with the emergence of wireless energy harvesting technologies, there is a transformative potential in addressing the power challenges faced by these sensors. By harnessing energy from the surrounding environment, such as solar, thermal, vibrational, or RF sources, these sensors can potentially operate …

Multiple Output Power Supply Using Toroidal Transformers For Medium Voltage Active Gate Drivers, Samhitha Venkata Machireddy

Graduate Theses and Dissertations

When operating in high power applications, power devices dissipate tens or hundreds of watts of power in the form of heat. The ability of the power devices to withstand power and dissipation of heat across the power devices becomes a prominent requirement in designing the power converter. This challenge demands a power converter design to be more effective and consistent which factors in size, cost, weight, power density and reliability. This study aims to propose a gate driver isolated power supply design that can be used in medium voltage applications (e.g., up to 10 kV) while respecting the principle of …

Stream Processor Development Using Multi-Threshold Null Convention Logic Asynchronous Design Methodology, Wassim Khalil

Graduate Theses and Dissertations

Decreasing transistor feature size has led to an increase in the number of transistors in integrated circuits (IC), allowing for the implementation of more complex logic. However, such logic also requires more complex clock tree synthesis (CTS) to avoid timing violations as the clock must reach many more gates over larger areas. Thus, timing analysis requires significantly more computing power and designer involvement than in the past. For these reasons, IC designers have been pushed to nix conventional synchronous (SYNC) architecture and explore novel methodologies such as asynchronous, self-timed architecture. This dissertation evaluates the nominal active energy, voltage-scaled active energy, …

Design Approaches To Enhance Power Density In Power Converters For Traction Applications, Shamar Christian

Graduate Theses and Dissertations

This dissertation presents a design strategy to increase the power density for automotive Power Conversion Units (PCUs) consisting of DC-DC and DC-AC stages. The strategy significantly improves the volumetric power density, as evident by a proposed PCU constructed and tested having 55.6 kW/L, representing an 11.2 % improvement on the Department of Energy’s 2025 goal of 50 kW/L for the same power electronics architecture. The dissertation begins with a custom magnetic design procedure, based on optimization of a predetermined C-core geometrical relationship and custom Litz wire. It accounts for electrical and thermal tradeoffs to produce a magnetic structure to best …

Analysis Of An Isolated Bidirectional Ćuk Converter, Yeny Hau Chen

Graduate Theses and Dissertations

The objective of this thesis is to perform an analysis of the isolated bidirectional Ćuk dc-dc converter topology and demonstrate the advantages and operation of this configuration through simulations using MATLAB/SimulinkTM and measurements collected from a 1.5-kW prototype tested at the Engineering Research Center (ENRC) laboratory of the University of Arkansas. The idea of integrating an active-clamp snubber circuit on each side of the converter, proposed by Dr. Sudip Mazumder from the University of Illinois, Chicago, limits the additional voltage stresses on the components due to the energy from the transformer’s leakage inductance. This is studied in this thesis to …

Improved Compact Modeling Of High Voltage Gallium Nitride High Electron Mobility Transistors, Md Maksudul Hossain

Graduate Theses and Dissertations

Since power converters shape a wide range of power electronic applications, the 'heart' of these conversions, such as solid-state switches, is crucial for achieving higher power density, lower loss, and higher efficiency operations. Although the limitations imposed by silicon-based power devices have been reduced by introducing novel devices such as IGBTs and super junction MOSFETs to allow for broader applications, solutions beyond silicon have presented a continuous challenge to the device engineers. Driving these converters at a higher switching frequency allows for higher power density. However, to support a higher frequency and operating temperature, superior materials, e.g., wide bandgap materials, …

Electrical Modeling For Dynamic Performance Prediction And Optimization Of Mcpms Layout, Quang Minh Le

Graduate Theses and Dissertations

In recent years, the fast development of Multichip Power Modules (MCPM) packaging and Wide Bandgap (WBG) technology has enabled higher voltage and current ratings, better thermal performance, lower parasitic parameters, and higher mechanical reliability. However, the design of the MCPM layout is a multidisciplinary problem leading to many time-consuming analyses and tedious design processes. Because of these challenges, the design automation tool for MCPM layout has become an emerging research area and gained much attention from the power electronics community. The two critical objectives of a design automation tool for MCPM layout are fast and accurate models for design insights …

Evaluation Of Single Phase Smart Pv Inverter Functions In Unbalanced Residential Distribution Systems, Darren Symonette

Graduate Theses and Dissertations

In the United States, smart PV inverters integrated with residential distribution systems are becoming a more common occurrence. With integration of smart PV inverters, power utilities are experiencing an increase of number of operations with regards to switched capacitor banks, voltage regulators and on load tap changers. These increases can lead to excess wear and tear on the devices causing power utilities to perform unwanted replacement and maintenance. However, smart PV inverters when controlled under specific functions can enable these inverters to provide reactive power and voltage control which in turn lowers the number of operations for switched capacitor banks, …

Controller Platform Design And Demonstration For An Electric Aircraft Propulsion Driv, Rosten Sweeting

Graduate Theses and Dissertations

With the growth in the aerospace industry there has been a trend to optimize the performance of an aircraft by reducing fuel consumption and operational cost. Recent advancements in the field of power electronics have pushed towards the concepts of hybrid electric aircraft also known as more electrical aircrafts. In this work, a custom controller board for an electric aircraft propulsion drive was designed to drive a permanent magnet synchronous motor. Design of the controller board required knowledge of the topology selection and power module selections. Simulations of the system were performed using MATLAB/Simulink to analyze the overall performance of …

Constraint-Aware, Scalable, And Efficient Algorithms For Multi-Chip Power Module Layout Optimization, Imam Al Razi

Graduate Theses and Dissertations

Moving towards an electrified world requires ultra high-density power converters. Electric vehicles, electrified aerospace, data centers, etc. are just a few fields among wide application areas of power electronic systems, where high-density power converters are essential. As a critical part of these power converters, power semiconductor modules and their layout optimization has been identified as a crucial step in achieving the maximum performance and density for wide bandgap technologies (i.e., GaN and SiC). New packaging technologies are also introduced to produce reliable and efficient multichip power module (MCPM) designs to push the current limits. The complexity of the emerging MCPM …

High Power Density And High Efficiency Converter Topologies For Renewable Energy Conversion And Ev Applications, Dereje Lemma Woldegiorgis

Graduate Theses and Dissertations

This dissertation work presents two novel converter topologies (a three-level ANPC inverter utilizing hybrid Si/SiC switches and an Asymmetric Alternate Arm Converter (AAAC) topology) that are suitable for high efficiency and high-power density energy conversion systems. The operation principle, modulation, and control strategy of these newly introduced converter topologies are presented in detail supported by simulation and experimental results. A thorough design optimization of these converter topologies (Si/SiC current rating ratio optimization and gate control strategies for the three-level ANPC inverter topology and component sizing for the asymmetric alternate arm converter topology) are also presented.

Performance comparison of the proposed …

Analysis And Optimization Of The Two-Phase Series Capacitor Buck Dc-Dc Converter, Salahaldein Ali Aboajila Ahmed

Graduate Theses and Dissertations

Current sharing schemes for conventional multi-phase converters are based on sensing each phase current to deliver the current information to their controllers. In conventional buck converters, this fact may require a preset current sharing ratio at the expense of efficiency, which eventually requires a larger sensing circuit to achieve the sensing accuracy of each phase. Introducing the concept of automatic current sharing is one of the solutions to tackle this issue. Automatic current sharing (Current Sharing Mechanism CSM) is an advanced way to distribute heat generation in multi-phase switching topologies at full load. A two-phase series capacitor buck converter (2-pscB) …

Junction Temperature Estimation Of Silicon Carbide Power Module Using Internal Gate Resistance As Temperature Sensitive Electrical Parameter, Michael Sykes

Graduate Theses and Dissertations

The junction temperature of a power module is measured non-intrusively and uninterrupted in its application by analyzing the dependency of gate resistance to temperature. The circuit configuration proposed consists of altering the gate loop path and adding a basic peak detection circuit with an added low-pass filter to accurately measure the small differences seen during a temperature change on the internal gate resistance. The testing on this Silicon Carbide power module shows that the internal gate resistance has a positive temperature coefficient. This causes the current and the voltage drop on the gate loop sensing resistance to reduce as the …

Nonmetallic Jet Impingement Thermal Management For Power Electronics Via Additive Manufacturing, Reece Whitt

Graduate Theses and Dissertations

The increase in energy demanded by transportation and energy sectors has necessitated highly efficient thermal management for reliable power electronics operations. Conventional cooling techniques are limited by their inability to target switching location hot spot temperatures, leading to non-uniform thermal gradients. These devices, such as cold plates and heat sinks, also utilize heavy metallic structures that can accentuate electromagnetic interferences generated by high voltage switching processes. This work proposes a non-metallic jet impingement cooler for more customized thermal management, while simultaneously reducing the harmful effects of electromagnetic interferences. Additive manufacturing is utilized to enable jet impingement zones to target individual …

Mission Profile Effects On Automotive Drivetrain Electronics Reliability: Modeling And Mitigation, Bakhtiyar Mohammad Nafis

Graduate Theses and Dissertations

The reliability of electronic devices is dependent upon the conditions to which they are subject. Temperature variations coupled with differences in thermal expansion between bonded materials results in thermomechanical stresses to build up, which can instigate failure in the interconnects or other critical regions. With the move towards electrification in the automotive industry, there is the increasingly important consideration of powertrain electronics reliability, the pertinent conditions being governed by the drive cycle or mission profile of the vehicle. The mission profile determines the power dissipated by the electronic devices, which determines the peak and mean temperature, temperature swing and the …

A Double-Sided Stack Low-Inductance Wire-Bondless Sic Power Module With A Ceramic Interposer, Si Huang

Graduate Theses and Dissertations

The objective of this dissertation research is to develop a novel three-dimensional (3-D) wire bondless power module package for silicon carbide (SiC) power devices to achieve a low parasitic inductance and an improved thermal performance. A half-bridge module consisting of 900-V SiC MOSFETs is realized to minimize stray parasitic inductance as well as to provide both vertical and horizontal cooling paths to maximize heat dissipation. The proposed 3-D power module package was designed, simulated, fabricated and tested. In this module, low temperature co-fired ceramic (LTCC) substrate with vias is utilized as an interposer of which both top and bottom sides …

Grid Strength Assessment Trough Q-V Modal Analysis And Maximum Loadability Of A Wind-Dominated Power System Using P-Q Regions, Pierre Obed Dorile

Graduate Theses and Dissertations

Climate change is a menace to the existence of the world and policymakers are trying totackle this phenomenon by deploying large-scale wind farms into their grids. Among them, wind energy shows a promising future to substitute the traditional power plants. However, the deployment of these wind farms into the grid is not a panacea that does not pose any challenges to the grid operators. Keeping the power system voltage stable while considering the strength of the transmission grid is among the major challenges facing by the transmission system operators. Amid normal operation and fault conditions, wind farms should help the …

Electrochemical Deposition In Energy Storage Devices, Witness Atutala Martin

Graduate Theses and Dissertations

Metals, whether in a solid or soluble ion form, are a vital part of any electrochemical storage system. More so, Li metal is widely considered as the ideal anode because of its low density and low electrochemical potential (-3.04 V vs. the standard hydrogen electrode – SHE). However, just like most metals, it does not plate or strip evenly during cycling which can lead to cycling performance issues, short cycling lifespans, and even safety concerns brought about by dendrites that can cause internal short-circuiting within cells. This research focused on investigating the electroplating of metals in both aqueous and non-aqueous …