Power and Energy Commons^™

Fault Location In Transmission Systems Using Synchronized Measurements, Xiangqing Jiao

Theses and Dissertations--Electrical and Computer Engineering

Compared with conventional measurements from supervisory control and data acquisition (SCADA) system, phasor measurement units (PMUs) provide time-synchronized and direct measurements of phasors. The availability of synchronized phasor measurements can significantly improve power system protection and analysis. This dissertation is specifically committed to using synchronized measurements for estimation of fault locations in transmission systems.

Transmission lines are prone to various short-circuit faults. Accurate fault location is critical for rapid power recovery. Chapter 2 proposes a new fault location method based on sparse wide area measurements. One distinguishing feature of this method is its applicability to both transposed and untransposed transmission …

Analysis And Simulation Of Photovoltaic Systems Incorporating Battery Energy Storage, Oluwaseun M. Akeyo

Theses and Dissertations--Electrical and Computer Engineering

Solar energy is an abundant renewable source, which is expected to play an increasing role in the grid's future infrastructure for distributed generation. The research described in the thesis focuses on the analysis of integrating multi-megawatt photovoltaics (PV) systems with battery energy storage into the existing grid and on the theory supporting the electrical operation of components and systems. The PV system is divided into several sections, each having its own DC-DC converter for maximum power point tracking and a two-level grid connected inverter with different control strategies. The functions of the battery are explored by connecting it to the …

Improvements In Inverter Modeling And Control, Xiao Liu

Theses and Dissertations--Electrical and Computer Engineering

In this dissertation, the generalized averaging method models for inverters, reactive power control methods for photovoltaic inverters, and a noise immunity improvement for hybrid position observers for brushless dc motor drives are studied.

Models of inverters and other converters based on averaging have been widely used in numerous simulation applications. Generalized averaging can be applied to model both average and switching behavior of converters while retaining the faster run times associated with average-value models. Herein, generalized average models for single- and three-phase pulse width modulation inverters are proposed. The modulation signal for the proposed model could be either a sinusoidal …

Modeling Of A Multi-Megawatt Grid Connected Pv System With Integrated Batteries, Vandana Rallabandi, Oluwaseun M. Akeyo, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

The multi-megawatt grid connected photovoltaic (PV) system studied in the paper includes parallel arrays and power electronic units, each with their own DC-DC and DC-AC converters. In one configuration, the DC-AC converters of adjacent parallel sections are connected in cascade, in order to effectively operate as a multilevel inverter, thereby reducing the filtering requirements. Grid voltage oriented control is employed for inverters and a battery is incorporated for energy storage and performance improvement. Modeling is performed with the PSCAD/EMTDC software, such that both the power electronics components, controls and subsystem aspects, and the electric grid power system issues, can be …

On The Feasibility Of Carbon Nanotube Windings For Electrical Machines — Case Study For A Coreless Axial Flux Motor, Vandana Rallabandi, Narges Taran, Dan M. Ionel, John F. Eastham

Power and Energy Institute of Kentucky Faculty Publications

The latest developments in carbon nanotube (CNT) wires and yarns attract great interest for potential application to electromagnetic devices, such as electrical machines and transformers. The CNT material properties are largely different from copper and aluminum in terms of electrical conductivity, mass density, and thermal transfer, creating a new design paradigm for which the traditional rules and device topologies no longer apply. This paper proposes a brushless permanent magnet multidisc axial flux construction with coreless stator and special windings and minimal rotor back iron, as a suitable topology for CNT winding application. Specific analytical closed-form sizing equations, as a function …

Capture And Recycle Of Industrial Co2 Emissions Using Mircoalgae, Michael H. Wilson, Daniel T. Mohler, John G. Groppo, Thomas E. Grubbs, Stephanie Kesner, E. Molly Frazar, Aubrey Shea, Czarena L. Crofcheck, Mark Crocker

Center for Applied Energy Research Faculty and Staff Publications

A novel cyclic flow photobioreactor (PBR) for the capture and recycle of CO₂ using microalgae was designed and deployed at a coal-fired power plant (Duke Energy’s East Bend Station). The PBR was operated continuously during the period May–September 2015, during which algae productivity of typically 0.1–0.2 g/(L day) was obtained. Maximum CO₂ capture efficiency was achieved during peak sunlight hours, the largest recorded CO₂ emission reduction corresponding to a value of 81 % (using a sparge time of 5 s/min). On average, CO₂ capture efficiency during daylight hours was 44 %. The PBR at East Bend …

Large-Scale Optimization Of Synchronous Reluctance Machines Using Ce-Fea And Differential Evolution, Yi Wang, Dan M. Ionel, Vandana Rallabandi, Minjie Jiang, Steven Stretz

Power and Energy Institute of Kentucky Faculty Publications

A novel automated design optimization procedure based on the application of an ultrafast computationally efficient finite-element analysis (CE-FEA) for current-regulated synchronous reluctance machines supplied from power electronic converters is proposed. The CE-FEA uses only a minimum number of magnetostatic solutions in order to comprehensively evaluate performance, including ripple torque and core losses. The optimization algorithm is based on differential evolution, and uses as independent variables the torque angle and ratios for a generic rotor topology with four flux barriers. Two problems, one with two and the other with three objectives, are studied and results are compared. Global performance indices and …

Cable Sizing And Its Effect On Thermal And Ampacity Values In Underground Power Distribution, Obinna E. Igwe

Theses and Dissertations--Electrical and Computer Engineering

Over the past decade, underground power distribution has become increasingly popular due to its reliability, safety, aesthetic characteristics, as well as the ever increasing focus on the environmental impacts of the various stages of power generation and distribution. With the technological advances in this area, the process of running these cables have become more economical and efficient.

This thesis explores the practice of grouping multiple three phase cables in a common conduit, using the duct bank process, and analyzes the thermal and ampacity consequences on the individual lines. This analysis is done in an effort to better define and understand …

Hybrid Diesel-Electric Drivetrain For Small Agricultural Field Machines, Joseph Jackson, Joseph S. Dvorak

Biosystems and Agricultural Engineering Faculty Publications

In this project, a series electric drivetrain sized for small agricultural machinery was developed and tested. Electric drives have noted benefits in simplicity, controllability, integration with other electronics such as those that provide autonomous action, and in efficiency over a wide operating range. Their biggest drawback for agricultural use is the limited capacity of electrical energy storage. A series hybrid drivetrain provides a method to overcome these capacity constraints through the use of chemical energy storage. The series hybrid drivetrain in this research was designed using well-established components. It consisted of a diesel-electric generator, a lead acid battery pack, a …

Market Based Control Of Pv Inverters In A Distribution System, Kumar Rishikesh

Theses and Dissertations--Electrical and Computer Engineering

A growing energy crisis, a rapid climate change, and a constant depletion of fossil fuel necessitates the role of renewable energy resources like PV (Photovoltaics) and wind energy to form a group of distributed sources of generation. These circumstances promote the use of renewable resources meeting the environmental commitments in terms of checking pollution and toxic footprints. A group of PV and wind energy generation units may work together as micro players to form smart grid systems and participate in an existing distribution system to meet a portion of the daily energy demand. This will help in minimizing the network …

Genetic Algorithms In Stochastic Optimization And Applications In Power Electronics, Mengmei Liu

Theses and Dissertations--Electrical and Computer Engineering

Genetic Algorithms (GAs) are widely used in multiple fields, ranging from mathematics, physics, to engineering fields, computational science, bioinformatics, manufacturing, economics, etc. The stochastic optimization problems are important in power electronics and control systems, and most designs require choosing optimum parameters to ensure maximum control effect or minimum noise impact; however, they are difficult to solve using the exhaustive searching method, especially when the search domain conveys a large area or is infinite. Instead, GAs can be applied to solve those problems. And efficient computing budget allocation technique for allocating the samples in GAs is necessary because the real-life problems …

Mathematical Model For Current Transformer Based On Jiles-Atherton Theory And Saturation Detection Method, Xiang Li

Theses and Dissertations--Electrical and Computer Engineering

Current transformer saturation will cause the secondary current distortion. When saturation occurs, the secondary current will not be linearly proportional to the primary current, which may lead to maloperation of protection devices. This thesis researches and tests two detecting methods: Fast Fourier Transform (FFT) and Wavelet Transform based methods. Comparing these two methods, FFT has a better performance in steady state saturation, and Wavelet Transform can determine singularity to provide the moment of distortion.

The Jiles-Atherton (J-A) theory of ferromagnetic hysteresis is one approach used in electromagnetics transient modeling. With decades of development, the J-A model has evolved into different …

An Organic Mixed Ion-Electron Conductor For Power Electronics, Abdellah Malti, Jesper Edberg, Hjalmar Granberg, Zia Ullah Khan, Jens W. Andreasen, Xianjie Liu, Dan Zhao, Hao Zhang, Yulong Yao, Joseph W. Brill, Isak Engquist, Mats Fahlman, Lars Wågberg, Xavier Crispin, Magnus Berggren

Physics and Astronomy Faculty Publications

A mixed ionic–electronic conductor based on nanofibrillated cellulose composited with poly(3,4-ethylene-dioxythio­phene):­poly(styrene-sulfonate) along with high boiling point solvents is demonstrated in bulky electrochemical devices. The high electronic and ionic conductivities of the resulting nanopaper are exploited in devices which exhibit record values for the charge storage capacitance (1F) in supercapacitors and transconductance (1S) in electrochemical transistors.

Single Phase Multilevel Inverter For Grid-Tied Photovoltaic Systems, Martin Edward Prichard

Theses and Dissertations--Electrical and Computer Engineering

Multilevel inverters offer many well-known advantages for use in high-voltage and high-power applications, but they are also well suited for low-power applications. A single phase inverter is developed in this paper to deliver power from a residential-scale system of Photovoltaic panels to the utility grid. The single-stage inverter implements a novel control technique for the reversing voltage topology to produce a stepped output waveform. This approach increases the granularity of control over the PV systems, modularizing key components of the inverter and allowing the inverter to extract the maximum power from the systems. The adaptive controller minimizes harmonic distortion in …

Design Of Energy Storage Controls Using Genetic Algorithms For Stochastic Problems, Si Chen

Theses and Dissertations--Electrical and Computer Engineering

A successful power system in military applications (warship, aircraft, armored vehicle etc.) must operate acceptably under a wide range of conditions involving different loading configurations; it must maintain war fighting ability and recover quickly and stably after being damaged. The introduction of energy storage for the power system of an electric warship integrated engineering plant (IEP) may increase the availability and survivability of the electrical power under these conditions. Herein, the problem of energy storage control is addressed in terms of maximizing the average performance. A notional medium-voltage dc system is used as the system model in the study. A …

Stargrazer One: A New Architecture For Distributed Maximum Power Point Tracking Of Solar Photovoltaic Sources, Edgard Munoz-Coreas

Theses and Dissertations--Electrical and Computer Engineering

The yield from a solar photovoltaic (PV) source is dependent on factors such as light and temperature. A control system called a maximum power point tracker (MPPT) ensures that the yield from a solar PV source is maximized in spite of these factors. This thesis presents a novel implementation of a perturb and observe (PO) MPPT.

The implementation uses a switched capacitor step down converter and a custom digital circuit implementation of the PO algorithm. Working in tandem, the switched capacitor step down converter and the custom digital circuit implementation were able to successfully track the maximum power point of …

Nanostructured Semiconductor Device Design In Solar Cells, Hongmei Dang

Theses and Dissertations--Electrical and Computer Engineering

We demonstrate the use of embedded CdS nanowires in improving spectral transmission loss and the low mechanical and electrical robustness of planar CdS window layer and thus enhancing the quantum efficiency and the reliability of the CdS-CdTe solar cells. CdS nanowire window layer enables light transmission gain at 300nm-550nm. A nearly ideal spectral response of quantum efficiency at a wide spectrum range provides an evidence for improving light transmission in the window layer and enhancing absorption and carrier generation in absorber. Nanowire CdS/CdTe solar cells with Cu/graphite/silver paste as back contacts, on SnO₂/ITO-soda lime glass substrates, yield the …

A New Islanding Detection Method Based On Wavelet-Transform And Ann For Inverter Assisted Distributed Generator, Zhengyuan Guan

Theses and Dissertations--Electrical and Computer Engineering

Nowadays islanding has become a big issue with the increasing use of distributed generators in power system. In order to effectively detect islanding after DG disconnects from main source, author first studied two passive islanding methods in this thesis: THD&VU method and wavelet-transform method. Compared with other passive methods, each of them has small non-detection zone, but both of them are based on the threshold limit, which is very hard to set. What’s more, when these two methods were applied to practical signals distorted with noise, they performed worse than anticipated.

Thus, a new composite intelligent based method is presented …

Average-Value Modeling Of Hysteresis Current Control In Power Electronics, Hanling Chen

Theses and Dissertations--Electrical and Computer Engineering

Hysteresis current control has been widely used in power electronics with the advantages of fast dynamic response under parameter, line and load variation and ensured stability. However, a main disadvantage of hysteresis current control is the uncertain and varying switching frequency which makes it difficult to form an average-value model. The changing switching frequency and unspecified switching duty cycle make conventional average-value models based on PWM control difficult to apply directly to converters that are controlled by hysteresis current control.

In this work, a new method for average-value modeling of hysteresis current control in boost converters, three-phase inverters, and brushless …

Compensation Methods For Demand Response, Zhaofeng Wang

Theses and Dissertations--Electrical and Computer Engineering

Recently, more and more disputations about how demand response should be compensated have arisen. Moreover, the court is about to rehear the Order 745. It probably will have significant impact on the whole working system used to be built for demand response before. Nowadays, some power companies and utilities think that they will endure profits leakage while demand response resources still are compensated.

In this research, knowledge of demand response, local marginal price, Order 745 and other related concept will be explained in detail in case of misunderstanding. Associated with all these knowledge, a possible compensation method will be proposed. …

Co2 Recycling Using Microalgae For The Production Of Fuels, Michael H. Wilson, John Groppo, Andrew Placido, S. Graham, S. A. Morton Iii, Eduardo Santillan-Jimenez, Aubrey Shea, Mark Crocker, Czarena Crofcheck, Rodney Andrews

Center for Applied Energy Research Faculty and Staff Publications

CO₂ capture and recycle using microalgae was demonstrated at a coal-fired power plant (Duke Energy’s East Bend Station, Kentucky). Using an in-house designed closed loop, vertical tube photobioreactor, Scenedesmus acutus was cultured using flue gas as the CO₂ source. Algae productivity of 39 g/(m² day) in June–July was achieved at significant scale (18,000 L), while average daily productivity slightly in excess of 10 g/(m² day) was demonstrated in the month of December. A protocol for low-cost algae harvesting and dewatering was developed, and the conversion of algal lipids—extracted from the harvested biomass—to diesel-range hydrocarbons via catalytic …

Influence Of Reduction Promoters On Stability Of Cobalt/Γ-Alumina Fischer-Tropsch Synthesis Catalysts, Gary Jacobs, Wenping Ma, Burtron H. Davis

Center for Applied Energy Research Faculty and Staff Publications

This focused review article underscores how metal reduction promoters can impact deactivation phenomena associated with cobalt Fischer-Tropsch synthesis catalysts. Promoters can exacerbate sintering if the additional cobalt metal clusters, formed as a result of the promoting effect, are in close proximity at the nanoscale to other cobalt particles on the surface. Recent efforts have shown that when promoters are used to facilitate the reduction of small crystallites with the aim of increasing surface Co⁰ site densities (e.g., in research catalysts), ultra-small crystallites (e.g., < 2–4.4 nm) formed are more susceptible to oxidation at high conversion relative to larger ones. The choice of promoter is important, as certain metals (e.g., Au) that promote cobalt oxide reduction can separate from cobalt during oxidation-reduction (regeneration) cycles. Finally, some elements have been identified to promote reduction but either poison the surface of Co⁰ (e.g., Cu), or produce excessive light gas selectivity (e.g., Cu and Pd, or Au at …

Fault Location Algorithms, Observability And Optimality For Power Distribution Systems, Wanjing Xiu

Theses and Dissertations--Electrical and Computer Engineering

Power outages usually lead to customer complaints and revenue losses. Consequently, fast and accurate fault location on electric lines is needed so that repair work can be carried out as fast as possible.

Chapter 2 describes novel fault location algorithms for radial and non-radial ungrounded power distribution systems. For both types of systems, fault location approaches using line to neutral or line to line measurements are presented. It’s assumed that network structure and parameters are known, so that during-fault bus impedance matrix of the system can be derived. Functions of bus impedance matrix and available measurements at substation are formulated, …

Prediction Model To Estimate The Zero Crossing Point For Faulted Waveforms, Md. Shakawat Hossan

Theses and Dissertations--Electrical and Computer Engineering

In any power system, fault means abnormal flow of current. Insulation breakdown is the cause of fault generation. Different factors can cause the breakdown: Wires drifting together in the wind, Lightning ionizing air, wires with contacts of animals and plants, Salt spray or pollution on insulators. The common type of faults on a three phase system are single line-to-ground (SLG), Line-to-line faults (LL), double line-to-ground (DLG) faults, and balanced three phase faults. And these faults can be symmetrical (balanced) or Unsymmetrical (imbalanced).In this Study, a technique to predict the zero crossing point has been discussed and simulated. Zero crossing point …

Modeling And Validation Of A Synchronous-Machine/Controlled-Rectifier System, Kyle A. Hord

Theses and Dissertations--Electrical and Computer Engineering

The hardware validation of a novel average-value model (AVM) for the simulation of a synchronous-generator/controlled rectifier system is presented herein. The generator is characterized using genetic algorithm techniques to fit standstill frequency response (SSFR) measurements to q and d-axis equivalent circuits representing the generator in the rotor reference frame. The generator parameters form the basis of a detailed model of the system, from which algebraic functions defining the parametric AVM are derived. The average-value model is compared to the physical system for a variety of loading and operating conditions including step load change, change in delay angle, and external closed-loop …

Investigation Of Protection Issues And Method For The Distribution System With Distributed Generations, Ke Xu

Theses and Dissertations--Electrical and Computer Engineering

Because DGs are introduced into distribution systems, the coordination of fuses and reclosers doesn’t work well. It means the original protection schemes are not available for the distribution systems with DGs. This thesis paper presents the study on the impacts of DGs on the fault current and voltage in the distribution system by the simulation of a model distribution system. After we study the impacts of DG on distribution systems, there is an introduction of current several current protection schemes and fault locations methods. At last, an adaptive protection scheme with a more efficient fault location method for the distribution …

Multifrequency Averaging In Power Electronic Systems, Fei Pan

Theses and Dissertations--Electrical and Computer Engineering

Power electronic systems have been widely used in the electrical power processing for applications with power levels ranging from less than one watt in battery-operated portable devices to more than megawatts in the converters, inverters and rectifiers of the utility power systems. These systems typically involve the passive elements such as inductors, capacitors, and resistors, the switching electronic components such as IGBTs, MOSFETS, and diodes, and other electronic circuits. Multifrequency averaging is one of the widely used modeling and simulation techniques today for the analysis and design of power electronic systems. This technique is capable of providing the average behavior …

A New Design Of Dc-Dc Converter For Capacitive Deionization Process, Zhiao Li

Theses and Dissertations--Electrical and Computer Engineering

The shortage of clean water has become a significant global problem, and capacitive deionization (CDI) is a technology that can be used to help relieve the problem. A Ćuk converter system that can recover energy from CDI cells is described. This converter transfers energy between two CDI cells when a cell is in its desorption period, allowing energy that would otherwise be lost to be recovered and improving overall system efficiency. In order to control the states of the MOSFET switches in the converter, a self boost charge pump is used. In this way, the microcontroller can control system duty …

Coordinated Voltage And Reactive Power Control Of Power Distribution Systems With Distributed Generation, Esa A. Paaso

Theses and Dissertations--Electrical and Computer Engineering

Distribution system voltage and VAR control (VVC) is a technique that combines conservation voltage reduction and reactive power compensation to operate a distribution system at its optimal conditions. Coordinated VVC can provide major economic benefits for distribution utilities. Incorporating distributed generation (DG) to VVC can improve the system efficiency and reliability. The first part of this dissertation introduces a direct optimization formulation for VVC with DG. The control is formulated as a mixed integer non-linear programming (MINLP) problem. The formulation is based on a three-phase power flow with accurate component models. The VVC problem is solved with a state of …

Influence Of Media Composition On The Growth Rate Of Chlorella Vulgaris And Scenedesmus Acutus Utilized For Co2 Mitigation, Czarena L. Crofcheck, Xinyi E, Aubrey Shea, Michael D. Montross, Mark Crocker, Rodney Andrews

Biosystems and Agricultural Engineering Faculty Publications

Atmospheric carbon dioxide levels have increased since the industrial revolution due to increasing combustion of fossil fuels. One possible CO₂ mitigation strategy is the use of microalgae for mitigation of CO₂. This paper focuses on the influence of media composition on the growth rate of two microalgae strains, Chlorella vulgaris and Scenedesmus actus. A KNO₃ based medium was found to work better for Chlorella, while a urea based equivalent worked better for Scenedesmus. The urea based media investigated here resulted in growth similar to that found with previously reported KNO₃ based media. …