Power and Energy Commons^™

Performance Loss Rate And Temperature Modeling In Predictive Energy Yield Programs For Utility-Scale Solar Power Plants, Katelynn M. Dinius

Master's Theses

The Gold Tree Solar Farm, designed by REC Solar, has a rated output power of 4.5 MW and began operation in 2018 to provide electricity to Cal Poly’s campus. Gold Tree Solar Farm site terrain consists of rolling hills and uneven slopes. The uneven typography results in interrow shading, requiring a modified tracking control algorithm to maximize power production. Predicting a utility solar field’s lifetime energy yield is a critical step in assessing project feasibility and calculating project revenue. The MATLAB-based predictive power model developed for this field overpredicted power in the middle of the day. The purpose of this …

Design And Analysis Of A Single-Stage Inverter Using Parallel Dc-Dc Converters For Solar Cell Application, Gabriel Leonides

Master's Theses

This thesis introduces the design and analysis of a single-stage inverter. A circuit was designed and simulated as a proof of concept to investigate the possibility of using boost and buck-boost converters to provide an AC output. The proposed circuit utilizes non-synchronous boost and buck-boost converters due to their simplicity in control signals as opposed to synchronous converters. The application of the proposed inverter is for use with individual solar cells. The aim of the inverter for a single cell is to improve the efficiency of a solar panel, whose performance is limited to the performance of the least efficient …

High Voltage Dc-Dc Converter Design For Submarine Application, Oscar Ambriz

Master's Theses

In this work a proof of concept for a step-down DC-DC converter used in a high voltage submarine application is presented. The purpose of the converter is to step down a 5000V-6000V input to a 24V output which can serve as an input to a submarine sensor. The completed system consists of two stages where the first stage is an unregulated switched capacitor converter to step down the initial input to a voltage range more appropriate for the selected second stage. The second stage is a regulated flyback converter topology which regulates the final output to the desired 24V. Performance …

Zero Voltage Switching Hybrid Voltage Divider Converter, Timothy Jeong

Master's Theses

This project proposes a new hybrid voltage divider DC-DC converter that utilizes switching capacitors and inductors to produce zero voltage switching (ZVS) at the turn on state of its switches. By achieving ZVS, the switching losses are significantly reduced; thus, increasing the overall efficiency of the converter at various loads. The goal for this thesis is to perform analysis of the operation of the converter, derive equations for sizing the main components, and demonstrate its functionality through computer simulation and hardware prototype. Results of the simulation and hardware testing show that the proposed converter produces the desired output voltage while …

Power Line Coupling Power Supply Design, Janine Gian Christii C. Darato, Jeni K. Kawate, Nicholas A. Marta

Electrical Engineering

In this project, a power supply was designed for a startup company, Perch Sensing, to detect wildfires with the use of distributed sensors across power lines. The purpose of the power supply is to provide 15W of power to a microcontroller, which controls the sensor nodes. The power supply hangs from power lines and draws energy by inductively coupling to these lines. Our design starts with a current transformer that steps down the current from the power line, which is fed into a shunting mechanism as a safety precaution when the load is absent, then to the power supply itself. …

Buck Converter With Voltage Foldback Protection, Fabian Aaron Enriquez, Pedro Rincon Rosales

Electrical Engineering

In this work, we implemented the idea of current foldback protection onto a buck converter. Current foldback protection essentially helps reduce the power dissipation which may be caused by a short circuit or overload scenario. To achieve the goal of this project, we used a combination of comparators, operational amplifiers and MOSFETs to create a current foldback sub controller. This controller would then serve as a feedback device between the output of the converter and the main controller to detect if a fault condition has occurred. Following the design, we performed simulation of the current foldback controller using PSpice and …

Solar Pv Emulator, Tristan Studer, Cody Kremer

Electrical Engineering

The implementation of a solar PV emulator. Creating a controllable testing environment which sufficiently recreates realistic conditions a photovoltaic cell would experience in real world use. The project aims to accurately show the efficiency and reliability of a solar PV cell, opposed to an ideal model which creates unrealistic expectations. The PV emulator implements conditions such as: irradiance, soiling and temperate changes. It gives feedback on a displayed IV curve and/or PV curve so the user may graphically analyze the output their PV cell produces given various conditions. It allows the user selectable conditions the solar cell may experience this …

Solar Photovoltaic Iv Curve Tracer, Jonathan W. Skelly

Electrical Engineering

The Solar Photovoltaic Current-Voltage (IV) Curve Tracer, sponsored by Cal Poly Professor Dale Dolan, characterizes solar array current vs. voltage curves for any given temperature and irradiance. The curve tracer is battery powered, and functions autonomously across loading conditions from short circuit to open load on any sub-450-watt solar array. The curve tracer supports separate data logging modes for both single cells and single modules to maximize data accuracy for each. For testing full strings of solar panels, up to 10 IV curves may be stored in persistent EEPROM memory. Stored data may be recalled later for output to a …

Optimization Of Single Axis Tracker Settings In The Cal Poly Goldtree Solar Farm, Charles A. Studdard, Liliana Reyes

Electrical Engineering

Solar farms use direct sunlight when operating; additionally, solar modules produce the most energy aligned perpendicular to the sun. Single axis solar tracking systems allow the rotation tilted photovoltaic panels to rotate during the day, maintaining the panels at the utmost efficiency angle. Achieving maximum power generation and reducing shade on the panels, make it crucial to have constant optimum positioning. Larger farms contain multiple rows and columns leading the panels to cast shadows on one another. Backtracking happens when you eliminate or reduce shadow casted on panels from adjacent modules. Panels positioned equidistantly and on even terrain allows backtracking …

2021 Department Of Energy Collegiate Wind Competition Electrical System, Grayson Capers, Shane Alayvilla, Justin Rodrigues

Electrical Engineering

In this work, the implementation of the electrical system for Cal Poly’s 2021 Department of Energy Collegiate Wind Competition turbine is described. The mission of this project was to complete the turbine testing tasks to the best of the team’s ability. This system includes an off the shelf slotless permanent magnet synchronous generator and rectifier to produce a DC voltage. To maximize the power output at below-rated wind speeds, current sensors, voltage sensors, and a dynamic load with variable resistance were designed and tested. To curtail the power and rotor speed in high wind events, the turbine was equipped with …

Hybrid Ac/Dc House, Vinh Q. Tran, Casey Winans, Erin O'Rourke

Electrical Engineering

The Hybrid AC/DC house is a proof of concept implementing a DC bus in residential power systems. The implementation of the DC bus is motivated by efficiency through a direct path for DC sources and loads. The avoidance of DC-to-AC and AC-to-DC conversions used in typical residential systems especially those with DC sources such as solar panels could experience higher efficiencies through only DC-to-DC conversions between the sources and the loads.

Dc-Dc Buck Boost Converter Using The Lt8390 Controller And Gan High Electron Mobility Transistors, Juan Manuel Urbano Jr, Brian Thongchai Keokot

Electrical Engineering

California Polytechnic State University, San Luis Obispo’s ongoing Energy Harvesting from Exercise Machines (EHFEM) project creates a sustainable energy source by converting physical exercise from exercise machines into renewable electricity. Implementing energy harvesting technology into the Recreation Center’s exercise machines helps Cal Poly make progress on its goal of carbon neutrality by 2050 [1]. An improvement to the system with new technology increases Cal Poly Recreation Center’s ability to save money and improve sustainability.

The focus of this project improves the design of Nicholas Serres, who used the LT8390 controller in his buck boost DC-DC converter [2]. This project improves …

Wildfire Early Detection System (Weds), Mason Mciver, Vincent Liang, Jeanreno Racines

Electrical Engineering

With climate change causing an increase in temperature over the past several decades, wildfires have been burning hotter and moving quicker leaving a trail of destruction in their path. Detecting a wildfire early allows firefighters to respond efficiently and effectively to ensure containment. With the rise of advanced computer vision and algorithms, autonomous systems can be used to monitor and report any fire activity. Having multiple devices spread out across a large area will allow first responders to map out the fire location and track the fire. By utilizing smart technologies, property damage can be minimized and residents living in …

Miniaturized Ultraviolet Imager High Voltage Power Supply, Nicholas Palmer, Jason Thomas Heil

Electrical Engineering

Sending satellites into orbit becomes exponentially more expensive with weight and size, so designing high-voltage DC-DC converters that can achieve kilovolt level outputs in a small form factor is crucial to reducing costs. The Miniaturized Ultraviolet Imager (MUVI) aims to monitor Earth’s ionosphere and report weather patterns to climate scientists within a 2U cube satellite footprint. The imaging equipment consists of a microchannel plate and phosphor screen that require 2.5kV and 5.5kV respectively at microamp level currents. This report explains the implementation of a high voltage boost cascaded flyback converter to meet all of the MUVI satellite output voltage requirements. …

Automation, Annunciation, And Emergency Safety Shutdown Of A Laboratory Microgrid Using A Real-Time Automation Controller (Rtac), Do Vo

Master's Theses

Over the last decade, microgrid deployments throughout the world have increased. In 2019, a record number of 546 microgrids were installed in the United States [1]. This trend continues upward to combat extreme weather conditions and power shortages throughout the country. To better equip students with the necessary skillsets and knowledge to advance in the microgrid field, Cal Poly San Luis Obispo's Electrical Engineering Department and the Power Energy Institute have invested resources to develop a laboratory microgrid.

This thesis sets to improve the laboratory microgrid's existing automation using the Schweitzer Engineering Laboratory SEL-3530 Real-time Automation Controller (RTAC). The improved …

Solar Soiling Mitigation, Claire Desmith

Electrical Engineering

This senior project aims to mitigate performance losses that occur in Photovoltaic (PV) systems due to soiling of the panels. Soiling is the natural occurrence of debris accumulation on panels, depending on local climate conditions. Soiling loss refers to efficiency lost due to dirt and dust accumulation on the panels. The debris reduces system output by shading on a smaller scale. In addition to uniform soiling, corner soiling is observed in framed modules as debris collects in the corners of the modules. While solutions currently exist to clean modules to mitigate soiling losses, these solutions are often expensive and time …

Early Wildfire Detection With Line Sensors, Virginia Yan

Master's Theses

Over the last few years, wildfires have become more devastating to communities as the fires are inevitably destructive to many homes, businesses, and ecosystems. Frequent wildfires also pose a significant threat to power grids and nearby residents as they can damage transmission lines and other electrical equipment, which in turn can cause major power shutdowns. Especially in western U.S., severe drought conditions and weather variability cause residents to become more vulnerable to wildfire disasters as their safety is threatened. We are incompetent to control the wildfires effectively despite existing advanced technologies. Hence, an algorithm based on energy conservation and heat …

Field Testing The Effects Of Low Reynolds Number On The Power Performance Of The Cal Poly Wind Power Research Center Small Wind Turbine, John B. Cunningham

Master's Theses

This thesis report investigates the effects of low Reynolds number on the power performance of a 3.74 m diameter horizontal axis wind turbine. The small wind turbine was field tested at the Cal Poly Wind Power Research Center to acquire its coefficient of performance, C­_p, vs. tip speed ratio, λ, characteristics. A description of both the wind turbine and test setup are provided. Data filtration and processing techniques were developed to ensure a valid method to analyze and characterize wind power measurements taken in a highly variable environment. The test results demonstrated a significant drop in the …

Dc-Dc Buck-Boost Converter Design For Energy Harvesting From Exercise Equipment, Nicholas Serres

Electrical Engineering

This project aims to improve energy harvesting efficiency from an exercise machine. Exercise machine energy harvesting has a small immediate impact but can eventually have an immense impact. An elliptical exercise machine energy converter outputs 5V-60V whereas the microinverters require approximately 36V. The buck boost DC-DC converter bridges the gap between the microinverter and the elliptical machine. Increasing the buck-boost controller efficiency increases power production. Greater power efficiency gives the whole system more financial viability, and additionally makes it a greater sustainable energy source.

Dc House Network Design And Modeling, Timmy Huu Nguyen, Joseph Shafie

Electrical Engineering

Although electricity is a necessity for nearly everything in daily life, many developing countries are unable to provide easy access to this utility. Often times within these developing countries, many renewable energy sources exist that are readily accessible to these same people that don’t have access to electricity within their homes, such as solar energy. However, the nature of renewable energy is that most renewable energy lacks consistency in power delivery throughout the day. An example of this is that solar energy isn’t available during the night. These small communities are often comprised of people that are familiar with each …

Smart Solar Charge Controller, Aria Pegah, Miclaine Emtman

Electrical Engineering

The technology of photovoltaics has been quickly evolving as we move toward a future with more clean energy. Energy conversion efficiency is key to making these systems the viable option amongst other sources of power. This project proposes a way to increase the power yield from a solar system by implementing smarter algorithms in the maximum power point tracking (MPPT) component of the system. MPPT is critical because environmental conditions may vary significantly for any given system due to irradiance and shading. The proposed method for MPPT utilizes a controller that uses swarm intelligence to do the power tracking.. This …

Iot Camera System For Monitoring Strawberry Fields, Simon Schoennauer

Master's Theses

A wireless imaging system for monitoring strawberry fields provides enough quality image data for computer vision algorithms to make meaningful yield predictions. This report contains a design for a wireless sensor network modified with mesh networking techniques to extend coverage range and a solar energy harvesting system to improve sensor node lifetime. A two hop system with six nodes is implemented in a laboratory environment validating the communication systems integrity over an 800’ range. Moving from a primary battery system to solar energy harvesting increases the module lifetime indefinitely.

Boost Converter Inductor Sizing Effects On The Performance Of Mppt Algorithms, Alan Nonaka

Master's Theses

With solar power and other renewables set to take over the market in the coming decades, maximum power point tracking will be essential to optimizing power output. One underserved topic of research is the effect of inductor current ripple on performance of Maximum Power Point Tracking (MPPT) algorithms. Many new topologies are focused on decreasing the ripple from PV source to increase efficiency and power output. However, not much has been done to show ripple degrading performance of MPPT algorithms. This study uses a boost converter topology to test the performance of constant duty cycle step Perturb and Observe (PO), …

Rf Power Amplifier, Angel De Jesus Delgado, Rachanon Wajanakunakorn, Andrew John Ferguson

Electrical Engineering

Wireless devices are part of everyday life, cellphones and radio receivers impact more people than any piece of technology. Thus, the respective building blocks continue to advance and achieve better performance. A primary component of all wireless communication systems is the power amplifier that drives the antenna. The Institute of Electrical and Electronics Engineers (IEEE) holds the International Microwave Symposium (IMS) every year where teams compete internationally for the most efficient RF Power Amplifier (PA). Power amplifier technologies strive to maximize efficiency and linearity. Topologies to consider are D, E, F, F-1 and Doherty since they have a maximum theoretical …

Distribution Line Multi-Tool, Michael Andrew Garcia, Drew Miller, Sukhdeep Singh, Ritwik Kesavath

Electrical Engineering

Power companies are always interested in the best possible monitoring equipment for their grid. The power line multi-tool developed would aid in the monitoring of the power system’s distribution network. This device assesses the current conditions of distribution power lines. The device is able to measure current, detect downed power lines, as well as recognize fire starting conditions, and have wireless communication for ease of access and installation. Overall this device greatly aids in helping utilities monitor their grid in more detail.

With the increase of dry climates yearly, several utility companies are taking measures to aid in the prevention …

Wind/Hydro Power Generation Simulator, Justin Shaun Otus, Nicholas Joseph Steele, Patrick Daniel Murphy

Electrical Engineering

This project aims to design a wind or hydro power generation simulator. The original scope of this project was to construct a physical simulation apparatus in which wind/water speed data is fed to a microcontroller that adjusts the control voltage of a motor drive. The spinning DC motor would generate power via a coupled generator whose power output would be a scaled down version of wind/hydroelectric generator power output given the same wind/water speed input. Due to Covid-19, the project was altered to be entirely virtual and was made through Simulink in MATLAB. The virtual simulator attempts to mimic physical …

Single Axis Solar Panel Tracking Mount Using Stepper Motor And Accelerometer Positional Control, Ezra Pramono

Electrical Engineering

Optimal solar panel systems rotate to track the sun, as solar panels operate at their maximum potential when the panel plane is completely normal to the sun’s rays. These tracking systems often using two axes of movement. This project is to design a system that will allow a solar panel to track the sun using only one rotational axis, which saves energy and uses fewer parts. The system tracks the entire range of the sun's motion and has positional feedback to allow control of the solar panel's angle. The position of the tracking system is controllable via an external computer. …

Conducted And Radiated Emi Measurements Of Parallel Buck Converters Under Varying Spread Spectrum Parameters, Elena Postupalskaya, Nathan Wang

Electrical Engineering

The Conducted and Radiated EMI Measurements with Parallel Buck Converters Under Varying Spread Spectrum Parameters research senior project aims to explore the effects from Spread Spectrum Frequency Modulation (SSFM) on the input electromagnetic interference (EMI) or noise of a switching power supply, specifically with LM53601MAEVM hardware. The input EMI is important as the main input bus needs to be clean to provide a reliable source for other sensitive devices connected to it. SSFM can replace a conventional EMI filter and save weight, space, and cost. This project provides a basis in terms of the impacts of variable SSFM in simulation …

Pulsed Electric Field System Development For Algae Biofuel Extraction, Juan David Gonzalez Aguayo, Aspyn Bessler

Electrical Engineering

The search for sustainable alternatives to fossil fuels proves necessary due to the effects fossil fuels have on Earth’s environment. These alternatives must have a minimum ecological footprint and cause no long-term harm to the environment. An environmentally friendly fuel is necessary to usher in a generation of renewable green energy.

The production of algae refined biofuels becomes a possible solution to this growing issue. Algae absorb CO2from the atmosphere during their reproduction and growth cycles, yielding a positive environmental impact. As the biofuel is refined and becomes suitable for use, the combustion of the finished fuel generates an equal …

Energy And Economic Losses Due To Soiling On Utility Scale Pv Systems To Guide Timing Of Cost Effective Cleaning, Sophia Mcmillin Stockburger, Vicente Jesus Rios

Electrical Engineering

The purpose of this senior project is to develop and recommend a cleaning schedule for Goldtree Solar Farm that is both economically beneficial and an efficient use of cleaning for the client. Solar farms can have various factors that influence the cleaning schedule such as weather behavior, time of the year, soiling, and other factors. Through this senior project, the goal is to assess these factors effect on the solar farm to produce a cleaning schedule that will maximize energy production, maximize profits, and prevent insignificant cleaning

This analysis is motivated by defining and promoting the benefits of regular maintenance …