Power and Energy Commons^™

Series Reports From Professor Wei’S Group Of Chongqing University: Advancements In Electrochemical Energy Conversions (2/4): Report 2: High-Performance Water Splitting Electrocatalysts, Ling Zhang, Wang-Yang Wu, Qiu-Yue Hu, Shi-Dan Yang, Li Li, Rui-Jin Liao, Zi-Dong Wei

Journal of Electrochemistry

The unavailability of high-performance and cost-effective electrocatalysts has impeded the large-scale deployment of alkaline water electrolyzers. Professor Zidong Wei’s group has focused on resolving critical challenges in industrial alkaline electrolysis, particularly elucidating hydrogen and oxygen evolution reaction (HER/OER) mechanisms while addressing the persistent activity-stability trade-off. This review summarizes their decade-long progress in developing advanced electrodes, analyzing the origins of sluggish alkaline HER kinetics and OER stability limitations. Professor Wei proposes a unifying “12345 Principle” as an optimization framework. For HER electrocatalysts, they have identified that metal/metal oxide interfaces create synergistic “chimney effect” and “local electric field enhancement effect”, enhancing selective …

Local Electric Fields Coupled With Cl− Fixation Strategy For Improving Seawater Oxygen Reduction Reaction Performance, Yu-Rong Liu, Miao Zhang, Yan-Hui Yu, Ya-Lin Liu, Jing Li, Xiao-Dong Shi, Zhen-Ye Kang, Dao-Xiong Wu, Peng Rao, Ying Liang, Xin-Long Tian

Journal of Electrochemistry

Development of robust electrocatalyst for oxygen reduction reaction (ORR) in a seawater electrolyte is the key to realize seawater electrolyte-based zinc-air batteries (SZABs). Herein, constructing a local electric field coupled with chloride ions (Cl⁻) fixation strategy in dual single-atom catalysts (DSACs) was proposed, and the resultant catalyst delivered considerable ORR performance in a seawater electrolyte, with a high half-wave potential (E_1/2) of 0.868 V and a good maximum power density (Pmax) of 182 mW·cm⁻² in the assembled SZABs, much higher than those of the Pt/C catalyst (E_1/2: 0.846 V; Pmax: 150 mW·cm^{−2 …}

Bridging Materials And Energy Storage Mechanisms In Zn-I2 Batteries, Rong-Qi Liu, Wen-Shuo Shang, Jin-Tao Zhang

Journal of Electrochemistry

Zinc-iodine (Zn-I₂) batteries have emerged as a compelling candidate for large-scale energy storage, driven by the growing demand for safe, cost-effective, and sustainable alternatives to conventional systems. Benefiting from the inherent advantages of aqueous electrolytes and zinc metal anodes, including high ionic conductivity, low flammability, natural abundance, and high volumetric capacity, Zn-I₂ batteries offer significant potential for grid-level deployment. This review provides a comprehensive overview of recent progress in three critical domains: positive-electrode engineering, zinc anode stabilization, and in situ characterization methods. On the cathode side, anchoring iodine to conductive matrices effectively mitigates polyiodide shuttling and enhances …

Design And Optimization Of Anode Catalysts For Direct Ethanol Fuel Cells: Advances And Challenges In C-C Bond Activation And Selective Modulation Of The C1 Pathway, Kai-Chi Qin, Meng-Tian Huo, Yu Liang, Si-Yuan Zhu, Zi-Hao Xing, Jin-Fa Chang

Journal of Electrochemistry

Direct ethanol fuel cells (DEFCs) are a promising alternative to conventional energy sources, offering high energy density, environmental sustainability, and operational safety. Compared to methanol fuel cells, DEFCs exhibit lower toxicity and a more mature preparation process. Unlike hydrogen fuel cells, DEFCs provide superior storage and transport feasibility, as well as cost-effectiveness, significantly enhancing their commercial viability. However, the stable C–C bond in ethanol creates a high activation energy barrier, often resulting in incomplete electrooxidation. Current commercial platinum (Pt)- and palladium (Pd)-based catalysts demonstrate low C–C bond cleavage efficiency (

Superhydrophilic Porous Coooh Nano-Architecture With Abundant Oxygen Vacancies For Enhanced Urea Electrooxidation At Ampere-Level Current Densities, Wen-Jing Lv, Xiao-Man Tang, Xue-Tong Wang, Wen-Cai Liu, Jian-Wen Zhu, Guo-Jing Wang, Yuan-Zhi Zhu

Journal of Electrochemistry

The conversion of urea-containing wastewater into clean hydrogen energy has gained increasing attention. However, challenges remain, particularly with sluggish catalytic kinetics and limited long-term stability of urea oxidation reaction (UOR). Herein, we report the loosely porous CoOOH nano-architecture (CoOOH LPNAs) with hydrophilic surface and abundant oxygen vacancies (O_v) on carbon fiber paper (CFP) by electrochemical reconstruction of the CoP nanoneedles precursor. The resulting three-dimensional electrode exhibited an impressively low potential of 1.38 V at 1000 mA·cm⁻² and excellent durability for UOR. Furthermore, when tested in an anion exchange membrane (AEM) electrolyzer, it required only 1.53 V at …

Structure Regulation Engineering For Biomass-Derived Carbon Anodes Enabling High-Rate Dual-Ion Batteries, Rui Zhou, Rui Liu, Yun-Nuo Li, Si-Jie Jiang, Tian-Tian Jing, Yan-Song Xu, Fei-Fei Cao

Journal of Electrochemistry

Dual-ion batteries (DIBs) usually use carbon-based materials as electrodes, showing advantages in high operating voltage, potential low cost, and environmental friendliness. Different from conventional “rocking chair” type secondary batteries, DIBs perform a unique working mechanism, which employ both cation and anion taking part in capacity contribution at an anode and a cathode, respectively, during electrochemical reactions. Graphite has been identified as a suitable cathode material for anion intercalation at high voltages (> 4.8 V) with fast reaction kinetics. However, the development of DIBs is being hindered by dynamic mismatch between a cathode and an anode due to sluggish Li^{+ …}

Assessing Solar Radiation Patterns In Sarawak Using Measured Data And The Hargreaves-Samani Model For Photovoltaic Systems Application, Chun Yong Soo, Xian Hwa Chan, Wan Mohamad Husni Wan Mokhtar, Ahmad Rujhan Mohd Rais

Makara Journal of Technology

This study evaluates the Hargreaves-Samani model for estimating solar radiation in five locations in Sarawak: Bintulu, Kapit, Sri Aman, Kuching, and Miri (Subis), using minimum and maximum temperatures as key inputs. Analysis reveals stable minimum temperatures (19.7 °C to 28.8 °C), supporting consistent solar radiation patterns favorable for Photovoltaic (PV) performance. Miri (Subis) recorded the highest daily maximum temperature of 44.8 °C, while Kuching had the lowest at 24.7 °C, highlighting significant regional climatic variability. Analysis also indicates strong solar potential in Bintulu, Kapit, Sri Aman, Kuching, and Miri, with radiation peaking at 7.5 kWh/m², though seasonal variations impact PV …

Techno-Enviro-Economic Approach For Electrification Of Rural And Shrimp Farming Regional Development Of An Isolated Island In Indonesia By Utilizing Hybrid Renewable Energy Systems, Fiqih Akbar Wijaya, Mohammad Akita Indianto

Journal of Materials Exploration and Findings

One of the challenges in developing and archipelagic countries such as Indonesia is maintaining energy demand in rural and isolated areas due to difficulties in electrical distribution. For instance, in areas like Bawean Island, no additional electricity capacity has been introduced in the past year, leading to an unmet potential customer demand. One of the possible options is by utilizing Hybrid Renewable Energy Systems (HRES) that are integrated with existing fossil fuel-based energy systems to support the growing energy demand in the remote island. A case study in Bawean Island is conducted with the projected energy demand covers the energy …

Research Progress On Thermal Management Of Lithium-Ion Batteries, Hong-Da Li, Qiu-Wan Shen, Zhao-Yang Zhang, Xin-Yue Zhao, Yuan Wei, Shi-An Li

Journal of Electrochemistry

Nowadays, new energy technologies are developing rapidly, energy storage systems are widely used, and lithium-ion batteries occupy a dominant position among them. Therefore, it is also very important to ensure their performance, safety and service life through thermal management technology. In this paper, the causes of thermal runaway of lithium batteries are reviewed firstly, and three commonly used thermal management technologies, namely, air cooling, liquid cooling and phase change material cooling, are compared according to relevant literature in recent years. Air cooling technology has been widely studied because of its simple structure and low cost, but its temperature control effect …

Regulating The Amount Of Graphene Oxide For Enhanced Capacitive Energy Storage Of Mof Derived Materials, Yong-Ji Qin, Jing-Quan Yang, Hao Wang, Mei-Ling Lian, Pei-Pei Jia, Jun Luo, Xi-Jun Liu, Jun-Feng Liu

Journal of Electrochemistry

In pursuit of more efficient and stable electrochemical energy storage materials, composite materials consisting of metal oxides and graphene oxide have garnered significant attention due to their unique structures and exceptional properties. Graphene oxide (GO), a two-dimensional material with an extremely high specific surface area and excellent conductivity, offers new possibilities for enhancing the electrochemical performance of metal oxides. In this work, we synthesized metal- organic framework (MOF) and GO composites by regulating the amount of GO, and successfully prepared composites of metal oxides supported by nitrogen-doped carbon frameworks and GO through a simple one-step calcination process. Based on the …

Analysis Of An Improved Reliability Dual-Buck Structured Three-Level Flying Capacitor Inverter, Almachius Kahwa Dr.

Tanzania Journal of Engineering and Technology (TJET)

With the increased demand for high-reliability power converters in the electric drive-train and propulsion systems, the efforts to design and analyze converters with high fault tolerance have become apparent. Among the emerging trends to improve the reliability of power converters is the incorporation of dual-buck (DB) structures in traditional converter topologies. Thus, this paper studies a single-phase dual-buck structured three-level flying capacitor (FC) inverter. The dual-buck flying capacitor (DBFC) inverter was constructed in such a way as to suppress the shoot-through problems that may occur because of the switching mismatch and gate driver delay, as exhibited in the traditional FC …

Review On Gas-To-Liquids Conversion Technology: Lessons From Case Studies And Potential Strategies For Implementation In Tanzania, Joseph H. Kihedu

Tanzania Journal of Engineering and Technology (TJET)

This review paper explores the transformative potential of Gas-to- Liquids (GTL) technology for harnessing Tanzania's vast natural gas resources. With significant discoveries of natural gas reserves totalling up to 57 Tcf in fields such as Songosongo, Mnazi Bay, Block 1, 2, 3 and 4. Tanzania is positioned to leverage GTL technology to convert these resources into high-value liquid fuels like gasoline, diesel and naphtha. Review of GTL process, its products and applications has been done. By analysing successful GTL projects globally and drawing lessons applicable to Tanzania, this paper provides strategic recommendations for policymakers and stakeholders to foster GTL development. …

Assessment Of Maintenance Performance Level Of Selected Hydropower Plants In Tanzania, Mahamudu H. Mtebwa

Tanzania Journal of Engineering and Technology (TJET)

Despite significant progress in increasing electricity access to over 78%, electricity reliability in Tanzania remains a concern, with frequent power outages reported. Maintenance issues in hydropower plants have been identified as a critical factor contributing to this problem. However, the specific maintenance performance levels have not been fully assessed. This study conducts a comprehensive evaluation of the maintenance performance of four key hydropower plants: Kidatu (204 MW), Kihansi (180 MW), Mtera (80 MW), and New Pangani Falls (68 MW). Data collected from staff surveys and maintenance records between 2018 and 2022 were used in the study. Although staff demonstrated a …

Redox-Active Monolayers On Ito Prepared By Post-Amidation And Direct Esterification And Their Spectroelectrochemical Characterization, Takamasa Sagara, Sae Nakai, Ryusuke Yofu, Shota Kojin

Journal of Electrochemistry

A redox-active monolayer on an optically transparent electrode constitutes a typical platform for spectroelectrochemical sensing. The necessity for its sophistication arises from the availability of multi-dimensional sensing signals. Simultaneous monitoring of the redox current and color change synchronized with the oxidation state change significantly enhances sensitivity and selectivity. This study aimed to elucidate the modification of an indium tin oxide (ITO) electrode with a viologen monolayer with an ordered orientation. Novel methods were developed to immobilize a viologen molecule bearing a carboxyl group to form assembled monolayers through a condensation reaction using 1-ethyl-3-(3-dimethylaminopropyl)-carbodiimide with N-hydroxy-succinimide (EDC/NHS). In the two methods …

Ambient Co2 Capture And Valorization Enabled By Tandem Electrolysis Using Solid-State Electrolyte Reactor, Yan-Bo Hua, Bao-Xin Ni, Kun Jiang

Journal of Electrochemistry

Electrocatalytic carbon dioxide reduction is a promising technology for addressing global energy and environmental crises. However, its practical application faces two critical challenges: the complex and energy-intensive process of separating mixed reduction products and the economic viability of the carbon sources (reactants) used. To tackle these challenges simultaneously, solid-state electrolyte (SSE) reactors are emerging as a promising solution. In this review, we focus on the feasibility of applying SSE for tandem electrochemical CO₂ capture and conversion. The configurations and fundamental principles of SSE reactors are first discussed, followed by an introduction to its applications in these two specific areas, …

Understanding The Morphology And Mass Transport Resistance Of Mesoporous Carbon-Supported Pemfc Based On Modeling Analysis, Hao Deng, Jia Liu, Zhong-Jun Hou

Journal of Electrochemistry

Mesoporous carbon supports mitigate Pt sulfonic poisoning through nanopore-confined Pt deposition, yet their morphological impacts on oxygen transport remain unclear. This study integrates carbon support morphology simulation with an enhanced agglomerate model to establish a mathematical framework elucidating pore evolution, Pt utilization, and oxygen transport in catalyst layers. Results demonstrate dominant local mass transport resistance governed by three factors: (1) active site density dictating oxygen flux; (2) ionomer film thickness defining shortest transport path; (3) ionomer-to-Pt surface area ratio modulating practical pathway length. At low ionomer-to-carbon (I/C) ratios, limited active sites elevate resistance (Factor 1 dominant). Higher I/C ratios improve …

Preparation And Modification Of Mxene Composites For Application In Electrochemical Energy Storage, Zhang-Hai You, Ding-Ze Lu, Kiran Kumar Kondamareddy, Wen-Ju Gu, Peng-Fei Cheng, Jing-Xuan Yang, Rui Zheng, Hong-Mei Wang

Journal of Electrochemistry

With the acceleration of advanced industrialization and urbanization, the environment is deteriorating rapidly, and non-renewable energy resources are depleted. The gradual advent of potential clean energy storage technologies is particularly urgent. Electrochemical energy storage technologies have been widely used in multiple fields, especially supercapacitors and rechargeable batteries, as vital elements of storing renewable energy. In recent years, two-dimensional material MXene has shown great potential in energy and multiple application fields thanks to its excellent electrical properties, large specific surface area, and tunability. Based on the layered materials of MXene, researchers have successfully achieved the dual functions of energy storage and …

Optimization Of Renewable Energy Systems: Comparative Analysis Of Advanced Algorithms And Photovoltaic-Electrolyzer Performance For Cost Reduction And Efficiency Enhancement, Mohamed-Amine Babay, Mustapha Adar, Ahmed Chebak, Mustapha Mabroukia

Journal of Electrochemistry

The increasing demand for cost-effective and efficient renewable energy solutions presents significant optimization challenges in hybrid energy systems. This paper addresses these challenges by conducting a comparative analysis of three advanced optimization algorithms—Lévy Flight Optimization (LFO), Archimedean Optimization (AO), and Quantum Gorilla Optimization (QGO)—to minimize the Total Net Present Cost (TNPC) and Levelized Cost of Energy (LCOE) in hybrid renewable energy systems. The study integrates critical cost parameters such as Capital Expenditure (CAPEX), Operational Expenditure (OPEX), replacement costs, and salvage values into an advanced optimization framework. Three system configurations are evaluated: Wind Turbines and Fuel Cells (WT/FC), Photovoltaic Systems and …

Theoretical Insights Into The Atomic And Electronic Structures Of Polyperyleneimide: On The Origin Of Photocatalytic Oxygen Evolution Activity, Yi-Qing Wang, Zhi Lin, Ming-Tao Li, Shao-Hua Shen

Journal of Electrochemistry

Polymeric perylene diimide (PDI) has been evidenced as a good candidate for photocatalytic water oxidation, yet the origin of the photocatalytic oxygen evolution activity remains unclear and needs further exploration. Herein, with crystal and atomic structures of the self-assembled PDI revealed from the X-ray diffraction pattern, the electronic structure is theoretically illustrated by the first-principles density functional theory calculations, suggesting the suitable band structure and the direct electronic transition for efficient photocatalytic oxygen evolution over PDI. It is confirmed that the carbonyl O atoms on the conjugation structure serve as the active sites for oxygen evolution reaction by the crystal …

Three-Dimensional Melamine Carbon Sponge/Nai As Cathode Materials For Sodium-Ion Batteries, Qian-Ying Huang, Yue Liu, Zi-Xin Lin, Shu-Yi Zheng, Ting-Ting Mei, Yu-Ting Tang, Ying-He Zhang, Jun Liu

Journal of Electrochemistry

The sodium-iodine (Na-I) battery exhibits significant potential as an alternative energy storage device to the lithium-ion battery. However, its development is hindered by inadequate electrical and thermal stability, as well as the dissolution and shuttling of polyiodide. In this study, we report a preparation method for melamine carbon sponge (MC) via carbonizing a commercially available kitchen sponge. It was revealed that the as-prepared MC, composed of unique self-growing carbon nanotubes, could provide both physical and chemical adsorption capabilities for intermediate polyiodides to improve the electrochemical performance of NaI. Consequently, the NaI/MC electrode effectively minimized polyiodide dissolution and reduced the electrochemical …

Who Owns The Wind: The Absence Of Community Wind Farms In California, Sky Berry-Weiss

Master's Projects and Capstones

Community ownership structures for wind farms have been around for decades, particularly in European countries, due to high socioeconomic benefits. Given these significant benefits, one might expect community wind to thrive in the United States—especially in a state like California, which prides itself on progressive climate policy and renewable energy leadership. Yet utility-scale community wind remains largely absent from research on California’s energy system, raising questions about its existence in the state. To pinpoint how many utility-scale community owned wind farms are in California, this study surveys every operational wind turbine in the state. After classifying each wind farm by …

Artificial Intelligence Applications For Grid-Connected Solar Inverters, Utkirjon Ubaydullaev, Sarvinoz Mirzaeva, Hasan Mustafoev

Chemical Technology, Control and Management

The increasing global demand for renewable energy has highlighted the importance of grid-connected solar inverters in ensuring efficient and stable power conversion. However, challenges such as fluctuations in solar energy generation, grid disturbances, and power quality issues necessitate advanced control strategies. The integration of artificial intelligence (AI) into solar inverters presents a transformative solution, enhancing performance, adaptability, and reliability in real-world applications.

This review explores the role of AI techniques, including machine learning (ML), deep learning (DL), fuzzy logic, and reinforcement learning (RL), in optimizing key inverter functionalities such as maximum power point tracking (MPPT), fault detection, power quality enhancement, …

Synthetic Inertia Provision For Load Frequency Control In Networks With High Penetration Of Renewable Energy Sources, Paulina Mkoi

Tanzania Journal of Engineering and Technology (TJET)

The integration of renewable energy sources (RESs) such as solar photovoltaic (PV) and wind energy has become a promising solution as the world shifts toward clean energy. Solar PV and wind resources are increasingly replacing conventional synchronous generators, leading to reduced system inertia and increased vulnerability to frequency instability during disturbances. To address this challenge, this study proposes a novel synthetic inertia provision strategy using a battery energy storage system (BESS) integrated alongside solar PV. The proposed method dynamically compensates for the loss of inertia by considering the variability of solar PV output due to changes in irradiance and temperature. …

Power-Beaming: Wireless Energy Transfer Using Lasers, Spencer L. Barnett

ATU Scholars Symposium

The objective of the project is to implement a wireless energy transfer system utilizing laser technology. This system involves modulating the laser’s beam profile and spatial distribution through precise optical manipulation. The energy transmitted by the laser is captured by a photovoltaic array, commonly referred to as a solar panel, which is engineered to convert incident photons into direct current (DC) electrical power. The current challenge is to develop a reliable wireless energy transfer mechanism capable of operating over extended distances, thereby overcoming the constraints imposed by wired connections, particularly in environments where wiring is impractical, such as in space. …

Variation Of Membrane Electrode Assembly Catalyst Layer In Unitized Regenerative Fuel Cell, Yollanda Nurcholifah, Dedi Rohendi, Edy Herianto Majlan, Nirwan Syarif, Addy Rachmat, Dwi Hawa Yulianti, Nyimas Febrika S

Journal of Electrochemistry

A unitized regenerative fuel cell (URFC) is a device that may function reversibly as either a fuel cell (FC) or water electrolysis (WE). An important component of this device is the Membrane electrode assembly (MEA). Therefore, this study aimed to compare the performance outcomes of MEA using electrodes with single and three catalyst layers. This study measured Electrochemical Surface Area (ECSA), Electrochemical Impedance Spectroscopy (EIS), X-ray Diffraction analysis (XRD), and X-ray Fluorescence (XRF). Furthermore, the round-trip efficiency (RTE) of the MEA, as well as the performance in FC and WE mode, was measured. In comparison, The ECSA values of Pt-Ru/C …

Electrocatalytic Nitric Oxide Reduction To Yield Ammonia Over Fe3C Nanocrystals, Sen Lin, Lang Zhang, Tong Hou, Jun-Yang Ding, Zi-Mo Peng, Yi-Fan Liu, Xi-Jun Liu

Journal of Electrochemistry

Nitric oxide (NO), which generally originates from vehicle exhaust and industrial flue gases, is one of the most serious air pollutants. In this case, the electrochemical NO reduction reaction (NORR) not only removes the atmospheric pollutant NO but also produces valuable NH₃. Hence, through the synthesis and modification of Fe₃C nanocrystal catalysts, the as-obtained optimal sample of Fe₃C/C-900 was adopted as NORR catalyst at ambient conditions. As a result, the Fe₃C/C-900 catalyst showed an NH₃ Faraday efficiency of 76.5% and an NH₃ yield rate of 177.5 μmol·h^–1·cm^{–2 …}

Ordering Degree Regulation Of Pt2Nico Intermetallics For Efficient Oxygen Reduction Reaction, Chen-Hao Zhang, Han-Yu Hua, Jun-Hao Yang, Qian Zhang, Chang Yang, De-Li Wang

Journal of Electrochemistry

Alloying transition metals with Pt is an effective strategy for optimizing Pt-based catalysts toward the oxygen reduction reaction (ORR). Atomic ordered intermetallic compounds (IMC) provide unique electronic and geometrical effects as well as stronger intermetallic interactions due to the ordered arrangement of metal atoms, thus exhibiting superior electrocatalytic activity and durability. However, quantitatively analyzing the ordering degree of IMC and exploring the correlation between the ordering degree and ORR activity remains extremely challenging. Herein, a series of ternary Pt₂NiCo intermetallic catalysts (o-Pt₂NiCo) with different ordering degree were synthesized by annealing temperature modulation. Among them, the o-Pt …

Performance Of Co2/H2O Co-Electrolysis In A Flat-Tube Solid Oxide Electrolysis Cell Stack Under Air-Free Environment, Xiao-Hui Zhong, Fei Wang, An-Qi Wu, Bei-Bei Han, Jian-Xin Wang, Wan-Bing Guan

Journal of Electrochemistry

This work investigates the transient performance and stability of CO₂/H₂O co-electrolysis in an air-free environment using a flat-tube solid oxide electrolysis cell (SOEC) stack. The results show that the transient behavior of the stack with and without blowing gas in the air electrode is almost the same. With a current density of 0.67 A·cm⁻²@750 °C, the stack operated for over 200 h under co-electrolysis conditions with no air blowing, and the voltage drop rate of the stack was approximately 0.203%/100 hours. Microstructure analysis reveals significant loss of Ni particles and formation of an insulating …

Metal Nitrides As Cathode Hosts For Lithium-Sulfur Batteries, Hai-Ji Xiong, Cheng-Wei Zhu, Ding-Rong Deng, Qi-Hui Wu

Journal of Electrochemistry

Lithium-sulfur batteries are considered as one of the potential solutions as integrating renewable energy systems for large-scale energy storage because of their high theoretical energy density (2600 Wh·kg^–1) and specific capacity (1675 mAh·g^–1). Currently, various strategies have been proposed to overcome the technical barriers, e.g., “shuttle effect”, capacity decay and volumetric change, which impede the successful commercialization of lithium-sulfur batteries. This paper reviews the applications of metal nitrides as the cathode hosts for high-performance lithium-sulfur batteries, summarizes the design strategies of different host materials, and discusses the relationship between the properties of metal nitrides and their …

Enhancing Cycle Life Of Graphite ‖ Lifepo4 Batteries Via Copper Substituted Li2Ni1-XCuXO2 Cathode Prelithiation Additive, Jian-Ming Zheng, Jing-Wen Zhang, Tian-Peng Jiao

Journal of Electrochemistry

Lithium nickel oxide (Li₂NiO₂), as a sacrificial cathode prelithiation additive, has been used to compensate for the lithium loss for improving the lifespan of lithium-ion batteries (LIBs). However, high-cost Li₂NiO₂ suffers from inferior delithiation kinetics during the first cycle. Herein, we investigate the effects of the cost-effective Cu substitution of Li₂Ni_1-xCu_xO₂ (x = 0, 0.2, 0.3, 0.5, 0.7) synthesized by high-temperature solid-phase method on the structure, morphology, electrochemical performance of graphite‖LiFePO₄ battery. The X-ray Diffraction (XRD) refinement result demonstrates that Cu substitution strategy is favorable …