Power and Energy Commons^™

Electrocatalytic Performance Of Pt/C And Pt/Wo3/C Catalysts For Methanol Oxidation, Yuan-Yuan Chu, Bing Wu, Ya-Wen Tang, Tian-Hong Lu, Ying Gao

Journal of Electrochemistry

The catalysts of Carbon supported Pt(Pt/C) and carbon supported Pt/WO₃(Pt/WO₃/C) were prepared with liquid phase reduction method.It was found that the catalytic activity and stability of the Pt/WO₃/C catalysts were increased with the addition of WO₃.When the atomic ratio of Pt and W was 1∶1,the best electrocatalytic performance of the Pt/WO₃/C catalyst for the methanol oxidation was obtained.This is attributed to the larger electrochemical surface area of Pt/WO₃/C and the weeker adsorption of CO towards the catalyst.

Preparation And Electrochemical Capacitance Of Spherical-Like Polypyrrole Doped With Heparin Sodium, Hong-Yu Mi, Xiao-Gang Zhang, Su-Dong Yang, Xiang-Guo Ye

Journal of Electrochemistry

Spherical-like polypyrrole with an average diameter of 100 nm as the electrode material for supercapacitor was prepared by a self-assembly process with heparin sodium salt as the dopant at-10 ℃.The morphology and electrochemical properties were characterized by transmission electron microscopy(TEM),cyclic voltammetry(CV),galvanostatic charge/discharge and electrochemical impedance spectroscopy(EIS) measurements.The results showed that the polypyrrole doped with heparin sodium salt exhibited good capacitive behavior.The specific capacitance of single electrode was up to 338 F/g at 3 mA/cm².

Synthesis Of Agv3O8 As High-Capacity Of Cathode Materials For Lithium Secondary Batteries Via A Soft Chemistry Technique, Xiao-Yu Cao, Tao Li, Ling-Ling Xie, Xiang-Yang Yan, Chi-Wei Wang

Journal of Electrochemistry

The layered cathode material of AgV₃O₈ has been prepared for the lithium secondary batteries via the soft chemistry technique. The so-synthesized powders were characterized by XRD(powder X-ray diffraction), SEM(scanning electron microscope) and LPSA(laser particle size analysis). The electrochemical property was investigated by the galvanostatic discharge-charge technique. The results indicated that the particale sizes of AgV₃O₈ prepared were small in the distribution of narrow range, which leads to high discharge capacity. Among them, the material synthesized at 400 ℃ displayed the first discharge capacity of 760.5 mAh/g.

The Effect Of Annealed Temperature On Properties Of Ru-Ir-Sn Oxide Anode Coatings, Lei Ji, Jun-Tao Wang, Li-Kun Xu, Wen-Bin Liu, Gui-Lin Xue

Journal of Electrochemistry

The anode coatings of Ru-Ir-Sn oxide were prepared by sol-gel method with different annealed temperatures.The influences of annealed temperature in properties of anode coatings were characterized by scanning electron microscope(SEM),energy dispersive X-ray detector(EDX),X-ray diffraction(XRD),potential of chlorine evolution,accelerated life,cyclic voltammetry and electrochemical impedance spectroscopy(EIS) tests.The results showed that the annealed temperature affected the morphology of coatings,while the electric quantities of cyclic voltammetry and double layer capacitances of anode coatings had a tendency to fall down and the potential of chlorine evolution and accelerated life had a tendency to increase as the annealed temperature increased.

Preparation And Photoelectrochemical Properties Of Fe-Doped Tio2 Nanotube Arrays, Jing Li, Lan Sun, Hui-Fang Zhuang, Cheng-Lin Wang, Rong-Gui Du, Chang-Jian Lin

Journal of Electrochemistry

The Fe-doped TiO₂ nanotube arrays were fabricated in Fe(NO₃)₃-HF mixing solutions by electrochemical anodic oxidation method,and characterized by FESEM,Raman,XPS and DRS.The effect of Fe concentratiions on photoelectrochemical property of the arrays was also investigated.The diameters and lengths of Fe-doped TiO₂ nanotube arrays were 50~90 nm and about 200 nm,respectively.Compared with the undoped TiO₂ nanotube arrays,the absorption edge of Fe-doped TiO₂ nanotube arrays appeared red shifting.The more Fe content,the larger red shifting,in addition,the photocurrent of Fe-doped TiO₂ nanotube arrays increased obviously.

Synthesis And Electrochemical Characteristics Of Li[Li(0.167)Mn(0.583)Ni(0.25)]O2 Cathode Material, Ling-Yan Yu, Wei-Hua Qiu, Fang Lian, Jia-Yuan Huang, Xao-Li Kang, Wei Liu

Journal of Electrochemistry

The cathode material of Li[Li_0.167Mn_0.583Ni_0.25]O₂ was synthesized by low-heat solid state reaction.The results of XRD and FESEM indicated that the powders of the material were well crystallized with the uniform diameters ranging from 60 nm to 100 nm and could be indexed as α-NaFeO₂ structure(R3-m space). Galvanostatic charge-discharge tests showed that the electrode delivered the capacity of about 120 mAh/g with good cyclability when cycled in 2.5~4.4V at 0.5C. When the cut-off potential was set up to 4.6V, the cathode delivered much larger capacities with the maximum of 234 mAh/g. It was …

Nuclear Energy, Steve Kraft

Native American Forum on Nuclear Issues

Abstract:

-Why Nuclear Energy?

-The lesson of the last 20 years in U.S. electricity policy:

– Diversified fuel and technology portfolio is essential

– All fuels and technologies (nuclear, coal, natural gas, renewables, efficiency) have a legitimate role

-The challenge for the future:

– Preserving/restoring diversified portfolio

– Ensuring resource adequacy, particularly in competitive markets

-Expanded use of nuclear energy is part of the answer

– Integrated used fuel management supports nuclear competitiveness

Cu Doping Lifepo4 And Its Electrochemical Performance, Ming-Sen Zheng, Shan-Ke Liu, Shi-Gang Sun, Quan-Feng Dong

Journal of Electrochemistry

LiFePO₄ and LiFePO₄ doped with Cu²⁺ ions were synthesized by solid-state reactions.The structure of LiFePO₄ and the Fe valence were analyzed by the XRD(X-ray diffraction) and XPS(X-ray photoelectron spectroscopy) respectively.The Cu doping position in LiFePO₄ is discussed.It has found that the volume of LiFePO₄ by doping Cu²⁺ ions is reduced.The minim Cu²⁺ ions doping does not almost change the binding energy of Fe₂p_1/2 in LiFePO_4.According to the experiment results,we conclude that most of the Cu²⁺ ions substitute the Fe²⁺ ions in LiFePO₄ when a …

A Study On Supercapacitor Based On Aligned Carbon Nanotubes, Xiao-Yan Ye, Yan-Zhi Wang, Hai-Yan Song, Zhuo Sun, Pin-Gang He, Yu-Zhi Fang

Journal of Electrochemistry

Large scale vertically aligned carbon nanotubes(ACNTs) with uniform length and diameter were prepared by the pyrolysis of iron(Ⅱ) phthalocyanine at low pressure.The ACNTs were activated by electrolyte-activation,acid-activation or electrochemical activation.The performance of the capacitor based on activated ACNTs was characterized by cyclic voltammograms which was of rectangular shape,impedence spectroscopy in which the phase is above 80° and the result specific capacitance was 16～32 F/g,which suggest that the ACNTs are the promising material for the supercapacitor.

Preparation And Electrochemical Performance Of Ordered Mesoporous Titanium Phosphate As Cathode Material For Li-Ion Battery, Qiong Wang, Attia Adel, Zhi-Cong Shi, Yong Yang

Journal of Electrochemistry

Ordered porous titanium phosphate materials were prepared by using the surfactant template combined with the sol-gel method. The samples were characterized by small angle X-ray diffraction(SA-XRD) method, N₂ adsorption/desorption techniques,high resolution transmission electron microscopy(HRTEM) and element analysis. It is found that the calcination temperature is a big influence on the porous structure, and electrochemical performance of the titanium phosphate materials, and the mesoporous titanium phosphate showed good performance in the electrochemical test, the first discharge capacity is 94 mAh/g at the current density of 150 mA/g. On the other hand, the no porous material with a low capacity of …

Synthesis Of Adipic Acid From Cyclohexanol By Electrochemical Oxidation Using Cr2O72-/Cr3+ As Indirect Oxidant, Zhen-Hai Liang, Yu-Qing Cui, Hong-Yan Sun

Journal of Electrochemistry

Adipic acid was synthesized by electro-oxidation of cyclohexanol taking Cr₂O₇^2-/Cr³⁺ as indirect oxidant.The best technological conditions were optimized by orthogonal experiment.The optimum condition are as follows: the temperature is 35 ℃,ratio of crude material is n(cyclohexanol)∶n(Cr₂O₇^2-)=0.4∶1 and concentration of H₂SO₄ is 4 mol·L^-1.Under these conditions,the yield of adipic acid can reach 70.29%.Moreover,The effects of concentration of Ag₂SO₄,(NH₄)₂SO₄,H₂SO₄and current density on the formation of Cr₂O₇^2-were also …

Mechanism Of The Cathode Reduction Of Ti(Ⅳ) In Molten Na3Alf6-Alf3, Hai-Bin Sun, Xiu-Rong Zuo, Zhi-Guo Zhong, Xue-Hui Hu

Journal of Electrochemistry

The mechanism of TiO₂ electrode process has been investigated by cyclic voltammetry and chronopotentiometry on the tungsten filament in molten Na₃AlF₆-AlF₃ salts at 990 ℃.The experimental results showed that electrochemical reduction of Ti(Ⅳ) precede were two steps,firstly Ti(Ⅳ) was reduced to Ti(Ⅱ),then Ti(Ⅱ) was reduced to Ti,namely: Ti(Ⅳ)→Ti(Ⅱ)→Ti.

Effects Of Oxidation Methods On The Stability Of Coooh Conductive Network In Foam Nickel Electrodes, Xiao-Feng Li, Yan-Wei Wei, Hui-Chao Dong

Journal of Electrochemistry

Two kinds of the cobalt oxyhydroxide conductive networks in foam nickel electrodes were prepared by different methods i.e.the electrochemical-oxidation(EO) and chemical-oxidation(CO) and which redox behaviors were studied by using cyclic voltammetry and X-ray diffraction measurements.The results show that the CoOOH(CO) has better redox reversibility than CoOOH(EO) and the structure of the former can be kept when nickel electrodes are subjected to a negative potential.Thus,98.7% capacity retention is demonstrated on nickel/metal-hydride batteries with CoOOH(CO) conductive network after being imposed over-discharge state storage;on the contrary,only 83.3% capacity retention is found on the batteries with CoOOH(EO) conductive network.

The Influence Of The Sputtering Power On The Structural And Electrochemical Properties Of Tin Oxide Films, Min-Zhen Cai, Jie Song, Ming-Sen Zheng, Qi-Hui Wu, Sun-Tao Wu, Quan-Feng Dong

Journal of Electrochemistry

Tin oxide films were deposited on silicon substrates at room temperature using the radio frequency(RF) magnetron sputtering with different sputtering power.The influence of sputtering power upon the crystal structure,surface morphology and electrochemical properties of tin oxide films were then investigated.The XRD and SEM results illustrate that the phase of tin oxide thin films changed from amorphous to crystalline and the grain size augments with the increase of the sputtering power.The constant current charge and discharge cycle tests imply that the initial irreversible capacity loss of Li/tin oxide batteries increase and which capacity decrease as the sputtering power increases.The sputtering power …

Molten Salt Treatment Of Mno2 And Investigation On Supercapacitor Properties, Ye Chen, Zun-Bo Zhang, Wei Zhang, Liang Liu, Zhi-Min Liu

Journal of Electrochemistry

The MnO₂ prepared by solid phase method is treated by KCl-NaCl-LiCl molten salt system.The XRD patterns indicated that the crystal structures of MnO₂ sample have had the α-MnO₂ and γ-MnO₂ phase,the crystallinity of sample is increased after treated by molten salt.The electrochemical properties were tested by cyclic voltammetry,constant current charge/discharge and AC impedance.The result shows that the supercapacitor performance of the treated material has improved.The specific discharge capacitance of the treated sample are 129.07 F·g^-1,increased by 27.88% compared to 100.94 F·g^-1 of untreated sample.Long cycle life and high coulombic efficiency were also demonstrated …

Potentiometric Response Of Glucose On Mno2-GoX Carbon Paste Electrode, Cai-Juan Wang, Xiao-Ya Hu

Journal of Electrochemistry

A novel carbon paste electrode(CPE) modified with MnO₂ and glucose oxidase(GO_x), is reported. Different factors, such as the effect of supporting electrolyte, pH of solutions,various paste glues, the amount of MnO₂ and temperature, which may influence the determination of H₂O₂ and glucose were tested to optimize. Based on above, potentiometric determination of glucose was achieved in neutral solution and at 35 ℃, the electrode gave a response of 36.12～34.62 mV/pG lucose between 2.0×10^-5 mol·L-1 and 5.2×10^-3 mol·L^-1 with a detection limit of 3.3×10^-6 mol·L^-1. Moreover, this kind …

Square Wave Stripping Voltammetric Behaviors Of Rutin On Glassy Carbon Electrode And Its Application, Jun Hua, Xiao-Ying He, Fang Liao, Qing-Tao Zhu

Journal of Electrochemistry

The electrochemical behaviors of rutin(Rt) at glassy carbon electrode were studied by square wave stripping voltammeter in the presence of 0.1mol·L^-1HAc-NaAc buffer solution(pH=3.0).The sensitive oxidation peak of rutin was observed and which potential peak is 0.46V(vs.SCE).The experimental parameters,such as pH value,deposition potential and deposition time were investigated and selected.The peak currents were proportional to the concentration of rutin in range of 5.0×10^-8 mol·L^-1~1.0×10^-6mol·L^-1,and the linear regression coefficient equaled 0.99799,the detection limit was 1.1×10-8 mol·L^-1.This method was applied to the determination of rutin content in tablet with satisfactory results.

The Determination Of Vitamin C By Bromophenol Blue Modified Glassy Carbon Electrode, Shu-Lin Zhang, Min-Jiao Li, Yi Luo, Xiao-Bo Wang

Journal of Electrochemistry

The content of ascorbic acid of(vitamin C) was analyzed by using fast cyclic voltamment with bromophenol blue(BPB) modififed GC-electrode,and which experimental conditions were optimiged.The results showed that the BPB modified GC-electrode had the good stability and anti-jamming faculty for analysing the content of ascorbic acid.A linear relationship between the peak current and concentration of vitamin C in the range of 0.0050~0.1500 g·L^-1 was obtained,which related coefficient and the detection limit are-0.9991 and 0.0010 g·L^-1,respeclively.The method has satisfactory results.

Effect Of Au At Different States On Electrocatalytic Performance Of Pd Catalyst For Oxidation Of Formic Acid, Xin Wang, Ya-Wen Tang, Tian-Hong Lu

Journal of Electrochemistry

Using liquid-reduction or complex-redution method,four catalysts,i.e,the Au/C,Pd/C,Pd-Au/C-T and Pd-Au/C-H were preparated and which electroanalytic activities and stabilities for the oxidation of formic acid were compares.It was found that the Au/C catalyst has no electrocatalytic activity,and the Pd/C catalyst possesses the good electrocatalytic performance for the oxidation of formic acid.The addition of Au into the Pd/C catalyst can increase the electrocatalytic activity and stability.Especially,the electrocatalytic activity and stability of the Pd-Au/C-T catalyst with the alloy of Pd and Au are better than that of the of the Pd-Au/C-H catalyst,in which,Pd and Au do not form the alloy.The investigation of its reason …

Synthesis Of 2,2′-Dichlorohydrazobenzene Using An Ion Exchange Membrane, Chao Zhang, Pei-Jin Li

Journal of Electrochemistry

Using an ion exchange membrane as a separator,the 2,2′-Dichlorohydrazobenzene is synthesized by the electrolytic reduction of o-chloronetrobenzene.The effects of electrode activation condition,current density,electrolyte temperature on electrolytic reduction are discussed.It was found that the optimum reaction temperature is 80 ℃.When the electrolyte concentration was 30% NaOH at the anode and 10% NaOH at the cathode,current density is 4.2A/dm²,the current efficiency reached 73% and yield is 83%.

New Method For Approximating Vague Sets To Fuzzy Sets Based On Voting Model, Jian Liu, Zhizhan Liu, Shunxiang Wu, Yongjian Zhang

Electrical and Computer Engineering Faculty Research & Creative Works

By analyzing Vague Sets voting model, we bring forth a new method for approximating Vague Sets to Fuzzy Sets, and its general process is presented in the article. In a voting model, firstly, we suppose that the abstainers must vote for once more, and the results are close studied. Then the randomicity, uncertainty, and conformity of voting are found. As we know, an abstainer may favor somebody, oppose somebody, or just abstain. In this article, we suppose the distribution of results is consistent with a normal distribution. So, we advance the new approximation method based on Gauss Distribution. © 2008 …

Electrochemical Oxidization Of Herring Sperm Dna And Its Interaction With Histone, Juan Xu, Gui-Ping Huang, Hong Li, Wei Zhu

Journal of Electrochemistry

The voltammetric behavior of herring sperm DNA at glassy carbon electrode and its interaction with histone have been investigated by using cyclic voltammetry,differential pulse voltammetry,and fluorescence measurement.In the potential range of 0.20 V to 1.25 V,it is found that an irreversible oxidative peak is exhibited in acid solution,but in the neutral or alkaline solution two oxidative peaks are observed.Oxidative peak potential values show a negative shift with increasing pH via a slope of-57 mV·pH-1 and a linear relation with DNA concentration in the range of 0.45 to 8.20 mmol·L^-1.In the presence of histone,the oxidative peak current of DNA …

Eiectro-Oxidation Of Methanol On Pdnio/C Catalyst In Alkaline Medium, Mei-Li Wang, Lin Sang, Cheng-De Huang

Journal of Electrochemistry

The electro-oxidation of methanol in alkaline electrolyte at in-house synthesized PdNiO/C and Pd/C catalysts and the effect of heat treatment on the structure and performance of catalysts were studied by cyclic voltammetry,chronoamperometry,chronopotentiometry and X-ray diffraction methods.It is shown that when the reduction temperature is 70℃ and the ratio between Pd and Ni is 8∶2,The PdNiO/C catalyst presents a highest activity for methanol electrooxidation.Calcining can increase the particle size and crystallinity of catalysts,but decrease the dispersion and activity of catalysts, too.Besides,the NiO is disengaged from Pd lattice by heat-treatment.The optimal PdNiO/C catalyst shows higher catalytic activity and much better poisoning resistance …

Preparation And Properties Of High Capacity Lifepo4, Jun Li, Gui-Tang Lai, Hui-Min Huang, Da-Guang Li, Xin-De Xia

Journal of Electrochemistry

Carbon-doped LiFePO₄/C and pure phase LiFePO₄ cathode materials were prepared by liquid-state precipitation reaction. The results of XRD, SEM, elemental analysis,FTIR and A.C.impedance tests show that the samples have had olivine structure and a 3.4V discharge platform.The tapped density of LiFePO₄/C sample could reach 1.46g/cm³, the initiate discharge capacity is 144.6mAh/g at 0.1C,which remained capacity is 93.2% after 20 cycles. The first discharge capacity is 133.5mAh/g at 1C and the capacity decreased 8.76% after 20 cycles.

Determination Of Malathion Based On Carbon Nanotubes Modified Electrode Incorporating Acetylcholinesterase, Lu Zhang, Yao-Dong Zhang, Hong-Lan Qi

Journal of Electrochemistry

A biosensor for determination of organophosphorus pesticide based on the acetylcholinesterase and multi-wall carbon nanotubes modified electrode is fabricated.Under the optimal conditions,the chronoamperometric current at +0.70V(vs.SCE) increased linearly with the concentration of malathion in the range from 6.0×10^-10 to 6.0×10^-9 mol·L^-1 with a detection limit of 1.0×10^-10 mol·L^-1.The recoveries of malathion in lake water is 97% to 105% determinated by this method.

Ion-Implanting Modification Of Layered Manganese Dioxide And Its Electrochemical Performance, He-Ning Huang, Dong-Ping Lv, Xing-Kang Huang, Qi-Wei Zhang, Yong Yang

Journal of Electrochemistry

Layered MnO₂(δ-MnO₂) was prepared by thermal decomposition of potassium permanganate.Ti was ion-implanted into such δ-MnO₂ by physical techniques,forming a composite(δ-MnO₂-Ti).These materials were characterized by XRD,SEM,XPS techniques and their electrochemical proprieties were investigated.The results showed that the layered structure of δ-MnO₂ did not been destroyed after Ti ion implantation,and the implanted Ti element was mainly Ti⁴⁺ as indicated by XPS.Both of the first and the highest discharge specific capacities of the ion-implanted layered MnO₂(δ-MnO₂-Ti),compared to those of δ-MnO₂,were improved significantly.

Electrochemical Behavior And Determination Of Luteolin At A Glassy Carbon Electrode, Ai-Lin Liu, Shao-Bo Zhang, Xiao-Sha Wu, Li-Ping Li, Yang-Yuan Cao, Li-Ying Huang, Xin-Hua Lin

Journal of Electrochemistry

The electrochemical behavior of luteolin was studied by voltammetry at a glassy carbon electrode in phosphate buffer solution.The results exhibited that the well-defined redox peak of luteolin is observed and the electrode process is adsorption-controlled.The charge transfer coefficient(α) was calculated as 0.66 in phosphate buffer solution(pH 4.0).The relationships between oxidation peak current and the concentration of luteolin are linear in the range of 1.0×10^-8 ～ 5.0×10^-6 mol·L^-1 by differential pulse voltammetric method.The detection limit had been estimated as 1.0×10^-8 molL^-1.This method can be used for the determination of luteolin with satisfactory results.

Selection Of Additions In The Process Of Electrochemical Synthesizing Of K2Feo4, Wei-Hua Yang, Dong-Qin Bi, Yan Zhou, Hong-Hui Wang, Xin-Ren Lan

Journal of Electrochemistry

Some of different additions including KIO₄ was added to the anodic electrolyte for electrochemical synthesizing of K₂FeO₄,the effects of these additions on current yield were investigated.XRD and SEM were used to characterize the structure and image of K₂FeO₄.The results show that KIO₄ is a preferable addition.When the mass dosage of KIO₄ is 0.02%,electrolysis time is 1 h,the current yield is enhanced by 31.6% and the corresponding purity of the product is improved by 3.85 %.

Study On Electrochemical Impedance Spectroscopy Of Carbon Steel Eroded In Methyldiethanolamine Solution, Dong-Ping Wei, Rong-Zong Hu, Dan-Mei Pan, Wei-Xiong Huang, Rui Dong

Journal of Electrochemistry

Corrosion behavior of carbon steel in methyldiethanolamine(MDEA) solution was investigated by Electrochemical Impedance Spectroscopy(EIS).The results were showed that the corrosion rate of carbon steel in solution containing dissolved oxygen is higher than that in solution removed of dissolved oxygen before cathodic activation.They were reversed after cathodic activation.The corrosion rate is increased at first and then decreased when the concentration of MDEA is increased in the blank solutions.In the simulated solutions containing quantities of!heat-stable salts(HSS),the corrosion rate is decreased monotonously with increase of the MDEA concentration.As anodic polarization potential is increased,the EIS of carbon steel in HSS simulated solution showed characteristics …

Oxygen Enrichment Effect Of Mno2-Pt/C Compound Catalyst To The Cathode Of Pemfc, Hong-Feng Xu, Mao-Feng Zhang, Quan-Quan Gan, Cai-Sheng Huang

Journal of Electrochemistry

TO study of the oxygen storage material of air cathode is crucial for increasing performance of proton exchange membrane fuel cell.Using the MnO₂ as oxygen storage materials,a MnO₂-Pt/C catalysts were prepared and is used to replace the conventional Pt/C in air cathode.The electrochemical performance of air cathode composed of MnO₂ supported on Pt/C and the properties of fuel cell composed of MnO₂-Pt/C were investigated by using the CV,galvanostatic dischange method and TEM.