Power and Energy Commons^™

Photoelectrochemical Properties Of Tio2 Nanoparticles, Jie Qu, Ying Li, Qi-Wei Jiang, Xue-Ping Gao

Journal of Electrochemistry

The protonated titanate nanoparticles were obtained at room temperature and subsequently calcined at different temperatures(300 ℃,400 ℃,500 ℃,600 ℃ and 700 ℃) in air.The obtained products were characterized by XRD,TEM and UV-Vis.It is found that the grain sizes of TiO₂ nanoparticles calcined at 300 ℃ were about 20 nm,and increased gradually with the temperature rise.Photoelectric performance was measured with I～V curve and electrochemical impedance spectroscopy(EIS).The TiO₂ nanoparticles obtained at 500 ℃ showed the best photoelectrochemical properties with a photovoltaic conversion efficiency of 6.39%,which is much higher than those at other temperatures.In addition,it is also demonstrated that the charge …

Synthesis,Characteristics And Electrochemical Performance Of Nano-Sized Snco/Graphite Composites As Anode For Lithium Ion Batteries, Jin-Shu Cai, Ling Huang, Fu-Sheng Ke, Shi-Gang Sun

Journal of Electrochemistry

The nano-structural Sn-Co/graphite composites were prepared by chemical reduction of the alloy electroless deposition solution in graphite suspensions, and the composites were annealed at 500 ℃. The phase structure and surface morphology of the composites were measured by XRD, SEM and Raman. The results indicate that there were high dispersions and high loadings of Sn-Co nanoparticles on graphite by thermal treatment. Electrochemical lithium storage performance was studied preliminarily on the obtained samples. The graphite modified with the Sn-Co nanoparticles possessed a higher electrochemical reversible capacity than that of graphite during the charge and discharge process. The appetency between the Sn-Co …

Spectroscopic Investigation Of Palladium-Copper Bimetallic Systems For Pem Fuel Cell Catalysts, Timo Hofmann

UNLV Theses, Dissertations, Professional Papers, and Capstones

One of the main barriers to commercialization of polymer electrolyte membrane fuel cells systems is cost, which is largely due to the need of platinum (Pt)-containing catalysts. In this thesis we investigate bimetallic systems consisting of a base metal (copper) and a noble metal (palladium) that, as an alloy on the nanoscale, mimic the electronic properties that make Pt desirable as a catalyst.

We present a detailed investigation of the electronic structure of carbon-supported Pd/Cu nanoparticle catalysts, model bilayer thin film systems, alloys, and various metal reference samples. We have investigated the valence band structure of the catalysts using a …

Voltammetric Determination Of Iodate Ion In Table Salt By Carboxylic Carbon Nanotubes Modified Carbon Paste Electrode, Jun-Hua Li, Fu-Xing Zhang, Jian-Qiu Wang, Zhi-Feng Xu, Rong-Ying Zeng, Yan Yu

Journal of Electrochemistry

A highly-sensitive and mercury-free method of determining iodate ion in table salt was established based on carboxylic carbon nanotubes modified carbon paste electrode.In 0.1 mol/L NaOH solution,there was a sensitive cathodic stripping peak on voltammograms.The stripping peak potential was-0.52 V when accumulation time of IO-3 at the modified electrode was 60 s and the potential scan rate was 300 mV/s.There was a good liner relationship between the peak current and IO-3 concentration in the range of 8.0×10^-10 ～ 5.0×10^-8 mol/L and 1.0×10^-7 ～ 3.0×10^-6 mol/L with the correlation coefficient of 0.999 and 0.998,respectively.The detection limit was …

The Hydrothemal Synthesis Of Nanoscale Lifepo4 And Its Electrochemical Performance, Si-Min Wang, Ming-Sen Zheng, Quan-Feng Dong

Journal of Electrochemistry

The cathode materials of LiFePO₄ were prepared via a hydrothermal reduction method using FeCl₃ as Fe source and iron as a reducing agent.The results showed that ferric salt could be reduced to ferrous salt completely under the hydrothermal condition and pure-phase LiFePO₄ was obtained based on the test results of XRD and FTIR. Carbon-coated LiFePO₄ was synthesized by pyrolysisng glucose at high temperature. The morphologies of pure LiFePO₄ displayed cluster-like while the LiFePO₄/C displayed sphere-like particles. The electrochemical test showed that the LiFePO₄/C had good rate performance,while LiFePO₄ delivered much …

Electrochemical Synthesis, Characterization And Fluorescence Property Of Nano Na2Sif6, Guo-Xu Qin, Xin-Jun Wan, Xi-Mei Yuan, Dao-Bao Chu

Journal of Electrochemistry

The nano TiO₂ film was prepared by sol-gel process and characterized with X-ray diffraction(XRD) and scanning electron microscope(SEM).It was found that the average size of pore diameter was about 80 nm for the nano TiO₂ film.The Nano Na₂SiF₆ was synthesized by electrochemical deposition on the nanoporous film electrode and characterized with XRD and transmission electron microscope(TEM).The result showed that the average size of nanoparticle was 20 nm for the nano Na₂SiF₆.The fluorescence property of nano Na₂SiF₆ was also studied briefly.The result indicated that the nano Na₂SiF …

Design And Fabrication Of The High Efficient Platinum-Nanoporous Gold Catalysts, Zhao-Na Liu, Jin-Tao Zhang, Fang Tian, Peng-Peng Liu, Hou-Yi Ma, Yi Ding

Journal of Electrochemistry

The nanoporous gold(NPG) electrodes with uniform pore sizes and ligaments were prepared by using a simple dealloying method.The as-prepared NPG showed high catalytic activity towards the oxidation of formic acid and formaldehyde.After tiny amount of platinum was deposited onto the NPG substrate,not only the structure stability of NPG was greatly improved,but also the Pt-Au bimetallic catalysts displayed the better catalytic activity and the stronger poison resistance towards the electrooxidation of small organic molecules than the bulk platinum due to synergistic effect between Au and Pt compositions.

Study On Electrocatalytic Oxidation Of Salbutamol At Carbon Nanotubes Modified Electrode, Ying-Liang Wei, Lu-Ping Zhang, Chen Shao, Hui Feng, Xian-Li Li

Journal of Electrochemistry

The multi-wall carbon nanotubes(MWNT) were dispersed successfully into water in the presence of dihexadecyl hydrogen phosphate(DHP) and a stable well-distributed suspension.A was formed sensor based on the multi-carbon nanotubes film coated glassy carbon electrode was developed.The electrochemical response of salbutamol was studied by square wave voltammetry.The oxidation peak potential of salbutamol at the modified electrode was observed at 0.604 V,which shifted about 40 mV negatively.The peak current increased 4.5 folds,in contrast to that at a bare electrode.Under optimal measurement conditions,there was a good linear relationship between the peak current(Ipa) and salbutamol concentration(C) in the range from 8.3 × 1 0 …

Electrocatalytic Oxidation Of Salicylic Acid At Novel Gold Nanoparticle-Modified Glassy Carbon Electrode, Yan-Ping Cui, Chang-Zhu Yang, Jian Huang, Wen-Hong Pu, Jing-Dong Zhang

Journal of Electrochemistry

A gold nano-particles modified glassy carbon electrode(GNP/GCE) was prepared by the"seed-mediated gold nano-particles growth method".Field emission scanning electron microscopy,ultraviolet-visible(UV-vis) spectroscopy analysis and electroalaylsis were employed to study the morphology and electrochemical performances.The resulting electrode showed excellent electro-catalytic activity toward the oxidation of salicylic acid and the response sensitivity was 1.8 fold than that obtained on GCE.Good linear relationship was obtained between response current and salicylic acid concentration in the range of 5.0 × 10^-7 ~8.0 × 10^-5 mol/L,which could be used in the detection of trace salicylic acid.

Structure And Property Of Molecular Self-Assembled Membrane With Zirconium Ion, Tian-De Wang, Rong Wang, Xia-Qin Wu, Zhi-Gang Guo, Wei-Wei Ji

Journal of Electrochemistry

According to the complex interaction between dodecyl phosphonate and stainless steel surface as well as the zirconium ion,the self-assembled monolayer and double-layer dodecyl phosphonate modified 304 type stainless steel electrode were prepared.The electrodes were characteristiced by static contact angles and electrochemical polarization methods.The results suggested that the double-layer modified stainless steel electrode had better corrosion inhibition effect than the monolayer modified electrode.

Carbon Nanotube Array Electrodes Based Supercapacitors With 3.5v Working Voltage, Hao Zhang, Gao-Ping Cao, Yu-Sheng Yang, Zhen-Nan Gu, Bin Xu, Wen-Feng Zhang

Journal of Electrochemistry

The carbon nanotube arrays(CNTA) were grown directly on the substrates of Ta and stainless steel by chemical vapor deposition.The button-like supercapacitors were fabricated based the CNTA electrodes.The electrochemical performance of CNTA based supercapacitors presentsed high working voltage(3.5 V),long cycle life,and good rate capability.The power and energy densities are were 928 kW·kg^-1 and 19 Wh·kg^-1,respectively(based on the mass of CNTA).

Preparation And Photoelectrochemical Properties Of Fe-Doped Tio2 Nanotube Arrays, Jing Li, Lan Sun, Hui-Fang Zhuang, Cheng-Lin Wang, Rong-Gui Du, Chang-Jian Lin

Journal of Electrochemistry

The Fe-doped TiO₂ nanotube arrays were fabricated in Fe(NO₃)₃-HF mixing solutions by electrochemical anodic oxidation method,and characterized by FESEM,Raman,XPS and DRS.The effect of Fe concentratiions on photoelectrochemical property of the arrays was also investigated.The diameters and lengths of Fe-doped TiO₂ nanotube arrays were 50~90 nm and about 200 nm,respectively.Compared with the undoped TiO₂ nanotube arrays,the absorption edge of Fe-doped TiO₂ nanotube arrays appeared red shifting.The more Fe content,the larger red shifting,in addition,the photocurrent of Fe-doped TiO₂ nanotube arrays increased obviously.

A Study On Supercapacitor Based On Aligned Carbon Nanotubes, Xiao-Yan Ye, Yan-Zhi Wang, Hai-Yan Song, Zhuo Sun, Pin-Gang He, Yu-Zhi Fang

Journal of Electrochemistry

Large scale vertically aligned carbon nanotubes(ACNTs) with uniform length and diameter were prepared by the pyrolysis of iron(Ⅱ) phthalocyanine at low pressure.The ACNTs were activated by electrolyte-activation,acid-activation or electrochemical activation.The performance of the capacitor based on activated ACNTs was characterized by cyclic voltammograms which was of rectangular shape,impedence spectroscopy in which the phase is above 80° and the result specific capacitance was 16～32 F/g,which suggest that the ACNTs are the promising material for the supercapacitor.

Determination Of Malathion Based On Carbon Nanotubes Modified Electrode Incorporating Acetylcholinesterase, Lu Zhang, Yao-Dong Zhang, Hong-Lan Qi

Journal of Electrochemistry

A biosensor for determination of organophosphorus pesticide based on the acetylcholinesterase and multi-wall carbon nanotubes modified electrode is fabricated.Under the optimal conditions,the chronoamperometric current at +0.70V(vs.SCE) increased linearly with the concentration of malathion in the range from 6.0×10^-10 to 6.0×10^-9 mol·L^-1 with a detection limit of 1.0×10^-10 mol·L^-1.The recoveries of malathion in lake water is 97% to 105% determinated by this method.

Study On Electrochemical Impedance Spectroscopy Of Carbon Steel Eroded In Methyldiethanolamine Solution, Dong-Ping Wei, Rong-Zong Hu, Dan-Mei Pan, Wei-Xiong Huang, Rui Dong

Journal of Electrochemistry

Corrosion behavior of carbon steel in methyldiethanolamine(MDEA) solution was investigated by Electrochemical Impedance Spectroscopy(EIS).The results were showed that the corrosion rate of carbon steel in solution containing dissolved oxygen is higher than that in solution removed of dissolved oxygen before cathodic activation.They were reversed after cathodic activation.The corrosion rate is increased at first and then decreased when the concentration of MDEA is increased in the blank solutions.In the simulated solutions containing quantities of!heat-stable salts(HSS),the corrosion rate is decreased monotonously with increase of the MDEA concentration.As anodic polarization potential is increased,the EIS of carbon steel in HSS simulated solution showed characteristics …

Fabrication And Charaterization Of Nitrogen-Doped Tio2 Nanotube Array And Its Visible Light Activity, Hui-Fang Zhuang, Yue-Kun Lai, Jing Li, Lan Sun, Chang-Jian Lin

Journal of Electrochemistry

Nitrogen-doped TiO₂ nanotube array was fabricated by an electrochemical anodic oxidation followed a wet process.XPS result indicates that the nitrogen atoms were doped into lattice of TiO₂ nanotubes.The UV-Vis spectra show that the photoabsorption of N-doped TiO₂ nanotube array film is enhanced in the visible light region.Compared with the TiO₂ nanotube array film,the N-doped TiO₂ nanotubes exhibite a higher photocatalytic activity which is evaluated by the decomposition rate of methyl orange using the tungsten-halogen lamp as light source.

Electrocatalytic Oxidation Of Methanol At The Nano Ni-B Amorphous Alloy Powdermicroelectrode, Yi-Xiong Zheng, Shi-Bing Yao, Shao-Min Zhou

Journal of Electrochemistry

Electrocatalytic oxidation of methanol at the nano Ni-B amorphous alloy powder-microelectrode in alkaline media was studied by using cyclic voltammetry.Compared to the highly preferred orientation(220) nickel electrode,The onset potential of methanol electrooxidation at the nano Ni-B microelectrode is negatively shifted about 0.04V,and the current density is increased approximately by 2 orders of magnitude.Thus,the nano Ni-B microelectrode has very strong electrocatalytic activity for the oxidation of methanol.The kinetic parameters were determined with the steady polarization curves.The results show that the rate constants for both the oxidation of Ni(Ⅱ) to Ni(Ⅲ) and the reduction of Ni(Ⅲ) to Ni(Ⅱ) at the nano Ni-B …

The Syntheses And Electrochemical Performance Of Nano-Mno2 For Supercapacitor, Jun Ma, Ming-Sen Zheng, Quan-Feng Dong

Journal of Electrochemistry

Nano-manganese dioxide were prepared by two different methods which are low temperature solid reaction and chemical deposition.The products were characterized by XRD,SEM,BET and constant current charge-discharge tests.The result shows that there is a close relationship between specific capacitance and BET surface areas.Meanwhile the specific capacitance was impacted little by the structure of the nano-manganese dioxides.However,the product performance of high rates,was influenced by structure,the higher rate can be obtained with the more perfect crystal structure.

Catalysis Of Nano Tio2 For Horseradish Peroxidase, Ya-Qi Zhu, Hai Wu, Hiu Liu, Jie Ma

Journal of Electrochemistry

Horseradish peroxidase immobilized on the surface of titanium dioxide nanoparticles and nanotube modified glassy carbon electrode.The HRP direct electron transfer reaction was compared between TiO₂ nanoparticles and nanotube GC electrode.The results demonstrated that the HRP on TiO₂ nanotube /GC electrode could catalyze electron exchange reaction between electroactivity center of HRP and electrode.And the research of antibody labeled HRP provides a selected signal for antibody-antigen immunoassay.

Template Synthesis And Electrochemical Studies Of Ag(Core)Au(Shell) Nanowires, Li Ling, Ya-Xian Yuan, Min-Min Xu, Jian-Lin Yao, Ren-Ao Gu

Journal of Electrochemistry

Agcore Aushell nanowires with different thicknesses were prepared by combining template synthesis and chemical reduction method,and characterized by SEM and cyclic voltammetry(CV).The CV results revealed that the AgcoreAushell nanowires with pinhole were transferred to pinhole free structure after several potential scans.By using thiophenol(TP)and p-aminothiophenol(PATP)as probe,the surface enhanced Raman scattering(SERS)effect was investigated on the core-shell nanowires.The results indicated that AgcoreAushell nanowires could be served as a potential SERS substrate,and the difference in the spectral feature of PATP adsorbed onto Au and Ag nanowires enable us to diagnose the pinhole effect of core-shell nanowires by SERS.

Study On The Electrogeneration And Properties Of Superoxide Ion In Aprotic Media By Using Carbon Nanotubes Powder Microelectrode, Ying-Liang Wei, Chen Shao, Hui Feng

Journal of Electrochemistry

Multi-wall carbon nanotubes are filled in the cavity at the tip of a microelectrode to form a carbon nanotubes powder microelectrode(CNTs-PME).The CNTs-PME is used to study the electrochemical reduction of oxygen in aprotic media.It is a nearly reversible redox process of the O₂/O₂^- couple at the CNTs-PME in the dimethyl sulfoxide(DMSO)solution.The heterogeneous electron transfer rate constant(ks)can be measured by steady-state voltammogram and the result is 9.8 10^-3cm /s.As a weak oxidant,the reaction of O₂^- with epinephrine was studied by cyclic voltammetry.Additionally,the reaction of O₂^- with benzoic acid was also discussed …

Preparation And Lithium Storage Performance Of Nano-Structural Sno2/Carbon Nanotubes Composite Electrodes, Hong-Bing Wei, Ling Huang, Xiao-Bin Wu, Fu-Sheng Ke, Jin-Shu Cai, Xiao-Yong Fan, Fang-Zu Yang, Shi-Gang Sun

Journal of Electrochemistry

The Nano-structural SnO₂/Carbon Nanotubes Composites were prepared in a solution of SnCl₂,ethylene glycol(EG),purified MWCNTs and sodium dodecyl sulfate(SDS) at 160 ℃.The phase structure and surface morphology of the composites were measured by XRD HRTEM and SEM.The results indicate that there are high dispersions and high loadings of SnO₂ nanoparticles on MWCNTs.Electrochemical lithium storage performance was studied preliminarily on the obtained samples.MWCNTs modified with SnO₂ nanoparicles were shown to have a higher electrochemical reversible capacity than that of MWCNTs during the charge and discharge process.MWCNTs can accommodate the larger structure strain of the active materials …

Comparison Of The Electrochemical Reactivity Of Electrodes Modified By Carbon Nanotubes With Different Sizes, Guo-Feng Yang, Neng-Qin Jia, Zhi-Yong Wang

Journal of Electrochemistry

The electrochemical activity of multi-walled carbon nanotubes(MWNTs) with different sizes,including four different MWNTs with the same length and different diameter,two different MWNTs with the same diameter and different length has been assessed and compared.The various MWNTs modified electrodes were prepared by immobilizing the suitable amount of MWNTs onto a glassy carbon electrode,and their voltammetric responses to ferricyanide,uric acid and dopamine were examined.The corresponding cyclic voltammetric data was showed that the electrochemical and electrocatalytic activities are depended on the nanotube length.The electrochemical reactivity of short MWNT(S-MWNT) is better than that of long MWNT(L-MWNT),which may be mainly attributed to the existence of …

Novel Electrochemical Method For Synthesis Of Nanostructured Materials Of Noble Metals Based On Poly(N-Vinylpyrrolidone) (Pvp), Wei Pan, Xiao-Kai Zhang, Ming-Hu Huang, Shao-Xin Huang, Xing-Li Feng, Hou-Yi Ma

Journal of Electrochemistry

Gold nanocrystals with controllable size were synthesized through a simple electroreduction method using poly(N-vinylpyrrolidone)(PVP) of different polymerization degree as both stabilizer and shape-controller for gold nanoclusters.Individual gold nanoparticles spontaneously assembled into the wire-and ring-shaped nanoparticle aggregates depending on the PVP's dynamic stretching and curling,and precursor nanoparticles grew into flat,single-crystalline nanoprisms with thickness of dozens of nanometers based on the oriented aggregation between particles.Besides,core-shell Au/Ag nanoparticles were conveniently synthesized through two-step electroreduction of noble metal ions in the presence of PVPK30.The electrochemical synthetic method based on PVP provides a new path for preparation of noble metal nanostructured materials with different shape …

Electrochemical Properties Of The Modified Carbon Nanotubes, Chun-An Ma

Journal of Electrochemistry

Powder micro-electrodes were prepared from raw carbon nanotubes and carbon nanotubes modified by carboxyl.The electro-reduction properties of both the raw and open-ended carbon nanotubes in p-Nitrophenol solution were investigated.The FTIR spectrum result indicated that the functional groups are successfully fixed on the surface of the carbon nanotubes after nitric acid treatment.The cyclic voltammetry results show that the electrochemical activity of carboxyl-modified carbon nanotubes was improved.The mechanism of electro-(reduction) for the carbon nanotubes after acid treatment was discussed.

Immobilization Of Cytochrome C On The Surface Of Single-Wall Carbon Nanotube And Its Direct Electron Transfer And Electrocatalysis, Ya-Jing Yin, Ya-Fen Lv, Ping Wu, Pan Du, Yan-Mao Shi, Chen-Xin Cai

Journal of Electrochemistry

Cytochrome c(Cyto c) was immobilized on the surface of the single-wall carbon nanotube(SWNT) by using the method of adsorption.Infrared spectroscopy indicated that the Cyto c remained in its original structure and did not undergo structural change after its immobilization on the SWNT.The direct electrochemistry of cyto c,which was adsorbed on the surface of the SWNT,was studied by cyclic voltammetry.The voltammetric results demonstrated that the SWNT had promoting effects on the direct electron transfer of Cyto c and also indicated that the immobilized Cyto c retained its bioelectrocatalytic activity to the reduction of H₂O₂.This modified electrode might …

Pre-Oxidative Amperometric Glucose Biosensor Incorporated With Carbon Nanotube And Pbo2, Hong-Lan Qi, Cheng-Xiao Zhang

Journal of Electrochemistry

A pre-oxidative amperometric glucose biosensor incorporated with carbon nanotube,ferrocenemonocarboxylic acid and PbO₂ was designed.The interferences coming from reduced substances,such as ascoribic acid and urine acid were eliminated by PbO₂.The oxidative current is linear at the potential of +0.40 V(vs.SCE) to the concentration of glucose in the range from 0.50 to 20 mmol·L^-1,and the detection limit of glucose is 0.1 mol L^-1.The relative standard deviation is 3.3% for seven successive assays at 5.0 mmol·L^-1glucose.This biosensors have been applied to determination of the glucose in serum with satisfying results.

Investigation On The Resistance To Electrochemical Oxidation Of Carbon Nanotubes With Various Diameters, Yu-Yan Shao, Ge-Ping Yin, Yun-Zhi Gao, Peng-Fei Shi

Journal of Electrochemistry

The resistance to electrochemical oxidation of multi-wall carbon nanotubes(CNT) with various diameters is investigated by applying a fixed potential of 1.2 V(RHE) for 120 h in 0.5 mol L^-1 H₂SO₄.The oxidation current of CNTs decreases with their diameters,but CNTs between 10~20 nm in diameter(D1020) shows the lowest oxidation current.XPS analysis shows that,after oxidation,the increase in surface oxygen for D1020 is the smallest,implying that the oxidation degree for D1020 is the lowest.The conclusion can be reached that CNTs between 10~20 nm in diameter are the most resistant to electrochemical oxidation.The difference in electrochemical stability of CNTs …

Electrochemical Studies On Electrocatalytic Activity Of AuCore PtShell Nanoparticles To Methanol Oxidation, Fang Bao, Jian-Lin Yao, Ren-Ao Gu

Journal of Electrochemistry

Au_corePt_shell nanoparticles with different thicknesses were prepared by using chemical reduction method,and characterized by ultraviolet-visible spectroscopy(UV-Vis),transmission electron microscopy(TEM) and cyclic voltammetry(CV).The electrocatalytic activity of Au_corePt_shell nanoparticles with the mean diameter of 70~80 nm to methanol oxidation was investigated by cyclic voltammetry in the acid solution.The results revealed that the prepared core-shell nanoparticles were covered by Pt shell and exhibited the similar optical property and electrocatalytic activity with the normal Pt surface.Moreover,the electrocatalytic activity increased with the electrochemical sweep in the certain potential range.It might be contributed by the special loose structure of Pt shell …

Electroless Nickel Plating On Carbon Nanotube With Non-Palladium Activation Procedure, Guang-Hui Hu, Hui-Huang Wu, Fang-Zu Yang

Journal of Electrochemistry

A new procedure of surface activation without using palladium salt was proposed for electroless nickel plating on carbon nanotubes.In the procedure,carbon nanotubes were oxidized by nitric acid and then neutralized with NaOH to create carboxyl surface groups which were used to adsorb Ni²⁺ ions,thereafter the adsorbed Ni²⁺ ions were chemically reduced into Ni nano-particles as a catalytic center for electroless nickel deposition,all these were further confirmed by infrared absorption spectra and electron microscopic observations.The results indicate that the procedure is feasible to electroless nickel plating on carbon nanotubes.The different morphology of deposits obtained from electroless plating was also …