Power and Energy Commons^™

Assessment Of Energy Efficiency In Beverage Industry, Mahamudu H. Mtebwa

Tanzania Journal of Engineering and Technology (TJET)

The brewery industry has a significant contribution to the national income. However, it is also associated with energy intensive processes and pollution. In this work, the energy efficiency assessment of the largest brewery in Tanzania i.e., Tanzania Breweries Limited has been conducted. Energy consumption analysis was conducted according to IEEE SA 739 1995. Important parameters used to assess brewery energy efficiency were boiler efficiency and losses, equipment energy productivity as well as load factor. It was found that the main energy consumers are packaging (54.63%), brewing (29.30%) and utilities (15.17%). More importantly, it was found that about 68% of the …

A Model For Sustainable Adoption Of Solar Photovoltaic Technology In Tanzania, Joseph Kihedu

Tanzania Journal of Engineering and Technology (TJET)

The aim of the study was to develop a sustainable model for enhancement of the solar PV technology adoption in Tanzania. The model was developed based on the identified barriers that hinder the adoption of solar PV technology and adopted the best strategies from successful projects. Further, the drivers and activities were developed based on selected best strategies from successful projects. The identified barriers to the adoption of solar PV technology, which are grouped into five associated categories and their significances, are lack of access to finance (32%), non-enforcement of policy and regulation (31%), technical (18%), lack of awareness (9%) …

An Experimental Approach Towards Pv-Based Solar System Sizing For An Engineering Laboratory, Muyideen O. Lawal

Tanzania Journal of Engineering and Technology (TJET)

This study aims at providing an experimental sizing procedure for a rooftop PV-based solar power system for an engineering laboratory. This was achieved by monitoring the peak power and energy delivered by an installed 20W solar panel into an 18 Ah battery. Knowledge of the average daily peak power and energy was used to determine the percentage rated capacity available for use and the sun hour. A load consumption comparison was also carried out with and without the connection of a load to inverter. In addition to this, the monitoring of the no-load consumption of the inverter was carried out. …

Viability Analysis Of Ubungo Ii Gas Power Plant Efficiency Improvement Using Co-Generation System, Aviti Thadei Mushi

Tanzania Journal of Engineering and Technology (TJET)

The power utility, Tanzania Electric Supply Company Limited (TANESCO) is faced with challenges of supplying adequate power to the ever-increasing demand. To this end, this paper explores the installed Ubungo Gas Power Plant (UGP II) located in Dar es Salaam to find means of utilizing it in co-generation method. The study embarked on detailed modelling of the system and run simulations which indicated that the co-generation can result to power generation efficiency increase between 10.42 to 50.92%. It is recommended to change the UGP II to exploit this co-generation method. Further, the study could be improved by including more parameters …

Sunsation’S Solar Powered Picnic Table, Michelle M. Barnett, Christopher Barber, Casey Durham, David Mason

Mechanical Engineering

Team SunSation is an interdisciplinary senior design project group that was tasked with developing a semi-permanent seating area for Cal Poly's electrical engineering courtyard. The EE courtyard is populated with plastic folding tables and chairs that are slowly falling apart. Dale Dolan, the head of the EE department, requested that a table design be developed that incorporates the use of solar panels. The addition of the solar panels to the table would help promote clean renewable energy as well as provide shade to those sitting in the courtyard.

The solution that SunSation arrived at is broken up into mechanical/structural, electrical, …

Developing A Miniature Smart Boat For Marine Research, Michael Isaac Eirinberg

Computer Engineering

This project examines the development of a smart boat which could serve as a possible marine research apparatus. The smart boat consists of a miniature vessel containing a low-cost microcontroller to live stream a camera feed, GPS telemetry, and compass data through its own WiFi access point. The smart boat also has the potential for autonomous navigation. My project captivated the interest of several members of California Polytechnic State University, San Luis Obispo’s (Cal Poly SLO) Marine Science Department faculty, who proposed a variety of fascinating and valuable smart boat applications.

Solar Solution For Mini-Rover, Michaella Ochotorena, Derick Louie, Jonathan Cederquist, Collin Petersen, Cole Korchek

Mechanical Engineering

This project focuses on designing, building, and testing a functional prototype of a collapsible solar array on the mini Mars rover being developed by client and sponsor, Mr. Rich Murray. Although many previous collapsible solar arrays have been deployed for space missions, the previous solar-powered Mars rovers only deployed their arrays once upon landing. This solar array will be able to collapse and deploy multiple times to allow for greater rover mobility and stability when the rover is not charging. This system is critical to the success of the rover project because it provides power without which the rover cannot …

Total Sky Imager Project, Ryan D. Maier, Benjamin Jack Forest, Kyle X. Mcgrath

Mechanical Engineering

Solar farms like the Gold Tree Solar Farm at Cal Poly San Luis Obispo have difficulty delivering a consistent level of power output. Cloudy days can trigger a significant drop in the utility of a farm’s solar panels, and an unexpected loss of power from the farm could potentially unbalance the electrical grid. Being able to predict these power output drops in advance could provide valuable time to prepare a grid and keep it stable. Furthermore, with modern data analysis methods such as machine learning, these predictions are becoming more and more accurate – given a sufficient data set. The …

Multifamily Complex Smart Locks For Property Management And Tenant Security, April Mills, Allen Chen, Dana Kumamoto, Michael Cook

Mechanical Engineering

Maintaining and managing hundreds of locks and physical keys for an apartment complex can be time consuming and costly, especially when the apartments turn over to new tenants. Our goal was to develop a smart door lock that is compatible with Obodo’s management app for apartment complexes to make accessing apartments secure and simpler for tenants and easier to manage for owners.

We designed and manufactured one smart door lock that is powered with four AA batteries and utilizes a dynamic NFC device and Bluetooth technology. The board can enter a sleep mode which reduces power consumption. The dynamic NFC …

Baker/Koob Final Report: Solar Solution For Mini Mars Rover, Jonathan Cederquist, Cole Korchek, Derick Louie, Michaella Ochotorena, Collin Petersen

Mechanical Engineering

This project focused on designing, building, and testing a functional prototype of a collapsible solar array on the mini Mars rover being developed by client and sponsor, Mr. Rich Murray. Although many previous collapsible solar arrays have been deployed for space missions, the previous solar-powered Mars rovers only deployed their arrays once upon landing. This solar array will be able to collapse and deploy multiple times to allow for greater rover mobility and stability when the rover is not charging. This system is critical to the success of the rover project because it provides power without which the rover cannot …

Dc Microgrid Fault Detection Using Multiresolution Analysis Of Traveling Waves, Rudy Montoya

Mechanical Engineering ETDs

Fast detection and isolation of faults in a DC microgrid is of particular importance. Fast tripping protection (i) increases the lifetime of power electronics (PE) switches by avoiding high fault current magnitudes and (ii) enhances the controllability of PE converters. This thesis proposes a traveling wave (TW) based scheme for fast tripping protection of DC microgrids. The proposed scheme utilizes a discrete wavelet transform (DWT) to calculate the high-frequency components of DC fault currents. Multiresolution analysis (MRA) using DWT is utilized to detect TW components for different frequency ranges. The Parseval energy calculated from the MRA coefficients are then used …

Dc Microgrid Fault Detection Using Multiresolution Analysis Of Traveling Waves, Rudy Montoya

Mechanical Engineering ETDs

Fast detection and isolation of faults in a DC microgrid is of particular importance. Fast tripping protection (i) increases the lifetime of power electronics (PE) switches by avoiding high fault current magnitudes and (ii) enhances the controllability of PE converters. This thesis proposes a traveling wave (TW) based scheme for fast tripping protection of DC microgrids. The proposed scheme utilizes a discrete wavelet transform (DWT) to calculate the high-frequency components of DC fault currents. Multiresolution analysis (MRA) using DWT is utilized to detect TW components for different frequency ranges. The Parseval energy calculated from the MRA coefficients are then used …

Zero-Power Ac Current Sensor, Omar Aragonez

Mechanical Engineering ETDs

In this study, a magnetic piezoelectric cantilever powered AC current and frequency sensor is proposed. This paper covers the configuration of the experimental setup, finite element modeling of the magnetic coupling, and the optimal spatial location of the magnetic proof mass in relation to the wire for smart grid applications. Solid and stranded copper wires of various gauges were used and carried current up to 30A. The magnets act as a proof mass to lower the frequency while also coupling to the magnetic field generated by the current carrying wire. The frequency of the AC current produces a sinusoidal force …

Economic Analysis Of Islanded Microgrid: A Case Study Of Kisiju Village - Coastal Region, Jackson Justo

Tanzania Journal of Engineering and Technology (TJET)

The concept of Microgrid (MG) has gained significant attention of researchers and projects on the business side of electrical power generation and utilization, particularly in electrification of islanded areas such as villages. Most of these microgrids are powered by renewable energy resources (RERs) and they distribute power in low voltage distribution networks. Hence, these systems are faced with reliability problems due to the intermittency nature of RERs which affect the technical as well as the return on Investment of specific projects. In the latter context, reliability and economic analysis of the MG systems is an inevitable choice. This paper presents …

Evaluation Of The Accuracy Of Different Pv Estimation Models And The Effect Of Dust Cleaning: Case Study A 103 Mw Pv Plant In Jordan, Loiy Al-Ghussain, Moath Abu Subaih, Andres Annuk

Mechanical Engineering Graduate Research

The estimation of PV production has been widely investigated previously, where many empirical models have been proposed to account for wind and soiling effects for specific locations. However, the performance of these models varies among the investigated sites. Hence, it is vital to assess and evaluate the performance of these models and benchmark them against the common PV estimation model that accounts only for the ambient temperature. Therefore, this study aims to evaluate the accuracy and performance of four empirical wind models considering the soiling effect, and compare them to the standard model for a 103 MW PV plant in …

Empirical Comparison Of Machine Learning Methods For Wind Power Predictions, Sidny M. Stewart

EWU Masters Thesis Collection

No abstract provided.

Wireless Power Transfer In Autonomous Mobile Microgrids, Carl Greene

Dissertations, Master's Theses and Master's Reports

The ability to autonomously dock unmanned ground vehicles plays a key role in mobile micro-grids, where efficient power transfer is paramount. The approach utilized in this work allows for near-field wireless power transfer in remote locations with minimal support. Establishing a micro-grid power system connection autonomously using wireless power eliminates the arduous task of designing a complex, multiple degrees of freedom (MDOF) robotic arm. The work presented in this thesis focuses on both the hardware and software within the micro-grid system. This particular near-field wireless system consists of a primary and secondary set of modules, comprised of Litz wire coils, …

The Capabilities And Limitations Of Flywheel-Based Energy Storage System Pertaining To Subways In The Event Of A Power Outage, Jaskaran Singh

Dissertations and Theses

In the city that never sleeps, power outages or blackouts can be a shock, especially if you are on a train amid one. For example, during the infamous 2003 blackout, thousands of people were left stuck and stranded in parts of Northeastern United States. In particular, with no trains or buses in service throughout the 5 boroughs of NYC, those stranded essentially had no way to go back home. Hotels, terminals, and airports alike became places of camping as the city seemed to come to a halt. For the sake of public safety and transit efficiency, this study explores a …

Torque Vectoring To Maximize Straight-Line Efficiency In An All-Electric Vehicle With Independent Rear Motor Control, William Blake Brown

Theses and Dissertations

BEVs are a critical pathway towards achieving energy independence and meeting greenhouse and pollutant gas reduction goals in the current and future transportation sector [1]. Automotive manufacturers are increasingly investing in the refinement of electric vehicles as they are becoming an increasingly popular response to the global need for reduced transportation emissions. Therefore, there is a desire to extract the most fuel economy from a vehicle as possible. Some areas that manufacturers spend much effort on include minimizing the vehicle’s mass, body drag coefficient, and drag within the powertrain. When these values are defined or unchangeable, interest is driven to …

Nonmetallic Jet Impingement Thermal Management For Power Electronics Via Additive Manufacturing, Reece Whitt

Graduate Theses and Dissertations

The increase in energy demanded by transportation and energy sectors has necessitated highly efficient thermal management for reliable power electronics operations. Conventional cooling techniques are limited by their inability to target switching location hot spot temperatures, leading to non-uniform thermal gradients. These devices, such as cold plates and heat sinks, also utilize heavy metallic structures that can accentuate electromagnetic interferences generated by high voltage switching processes. This work proposes a non-metallic jet impingement cooler for more customized thermal management, while simultaneously reducing the harmful effects of electromagnetic interferences. Additive manufacturing is utilized to enable jet impingement zones to target individual …

Mission Profile Effects On Automotive Drivetrain Electronics Reliability: Modeling And Mitigation, Bakhtiyar Mohammad Nafis

Graduate Theses and Dissertations

The reliability of electronic devices is dependent upon the conditions to which they are subject. Temperature variations coupled with differences in thermal expansion between bonded materials results in thermomechanical stresses to build up, which can instigate failure in the interconnects or other critical regions. With the move towards electrification in the automotive industry, there is the increasingly important consideration of powertrain electronics reliability, the pertinent conditions being governed by the drive cycle or mission profile of the vehicle. The mission profile determines the power dissipated by the electronic devices, which determines the peak and mean temperature, temperature swing and the …

Performance Loss Rate And Temperature Modeling In Predictive Energy Yield Programs For Utility-Scale Solar Power Plants, Katelynn M. Dinius

Master's Theses

The Gold Tree Solar Farm, designed by REC Solar, has a rated output power of 4.5 MW and began operation in 2018 to provide electricity to Cal Poly’s campus. Gold Tree Solar Farm site terrain consists of rolling hills and uneven slopes. The uneven typography results in interrow shading, requiring a modified tracking control algorithm to maximize power production. Predicting a utility solar field’s lifetime energy yield is a critical step in assessing project feasibility and calculating project revenue. The MATLAB-based predictive power model developed for this field overpredicted power in the middle of the day. The purpose of this …

Effect Of Deposition Conditions On Properties Of Molybdenum Back Electrode For Cu(In,Ga)Se2 Solar Cell And Cu(In,Ga)Se2 Performance Analysis Through Numerical Simulation, Meah Imtiaz Zulkarnain

Theses and Dissertations

In the first part of this research, the effect of the deposition conditions on properties of molybdenum thin-film were investigated to achieve desired characteristics for its application as the back electrode of Cu(In,Ga)Se2 solar cell. DC and RF magnetron sputtering modes were employed and two sputtering parameters namely, working pressure and sputtering power, were varied to determine the sputtering mode and the sputtering conditions best suited for Mo thin-films having required properties. Sputtered Mo samples were characterized to determine their structural and mechanical properties such as preferred growth orientation, crystallinity, grain size, dislocation density, adhesion, and micro strain, and electrical …

Assessment Of The Impacts Of Climate Variability On Hydropower Generation: A Case Study Of The New Pangani Falls, Tanzania, Dativa Byarufu

Tanzania Journal of Engineering and Technology (TJET)

Climate change poses potential impacts on hydropower generation either positively by increasing or negatively by decreasing river flow. This study assessed the impacts of climate variability on hydropower with a focus on the New Pangani Falls in Tanzania. Rainfall and temperature time series data from 1980-2014 were analyzed in relation to river discharge and associated impacts to hydropower generation. The Man-Kendall test was used to detect trend in both annual and seasonal time series. The results showed a negative trend in annual rainfall with Z= -2.41 at α = 0.05 and the slope Q = -0.964. Seasonal trend analysis showed …

An Improved Earned Value Management Method Integrating Quality And Safety, Brian Briggs

LSU Doctoral Dissertations

The construction industry invests significant time and money to improve quality and safety while reducing cost and schedule impacts. The industry has a sincere desire to improve construction project management methods to improve efficiency. Historically, quality and safety underperformances result from undermanaged quality control and safety activities. The cost and schedule impacts associated with poor quality work have always had an impact on construction operations. The unprecedented challenges and uncertainties of COVID-19 highlighted the need to improve the Earned Value Management (EVM) method within construction to reflect these quality and safety activities. The central goal of this dissertation is to …

Performance And Economics Of Solar Inverters And Module Level Power Electronics In A 1 Mw Photovoltaic System, Maxwell Criswell

Biological and Agricultural Engineering Undergraduate Honors Theses

Photovoltaic solar panels convert sunlight to electricity in the form of direct current; therefore, a necessary component of every photovoltaic system is an inverter to convert the electricity to usable alternating current. There are various commercially available inverter technologies manufactured today such as microinverters, string inverters, and central inverters, as well as module level power electronic devices such as DC optimizers that are capable of improving system performance in string and central inverter systems. This thesis compares the performance and economics of five different inverter and module level power electronic systems through model simulation using Helioscope software. The five alternatives …

Enercon Station Vacuum Pump Replacement, Clint Hembree, Jared D'Amico, Connor Moore, Paul Jeffrey Fontenot, Sydnee Castello, J.J. Clements

Senior Design Project For Engineers

This details the progress of the ENERCON pump replacement project as completed by the Kennesaw State University interdisciplinary senior design group. This project is a two-semester capstone effort for the engineering program at Southern Polytechnic School of Engineering, overseen by Dr. McFall during Fall 2020 and Dr. Khalid during Spring 2021 semesters. The 2020-2021 KSU Interdisciplinary Senior Design team was tasked with completing an Engineering Change Package (ECP) for existing vacuum pumps at ENERCON Station. The mechanical, electrical, and civil students worked together, performing evaluations on existing plant systems to ensure the plant could support the new vacuum pumps. By …

A Demand-Supply Matching-Based Approach For Mapping Renewable Resources Towards 100% Renewable Grids In 2050, Loiy Al-Ghussain, Adnan Darwish Ahmad, Ahmad M. Abubaker, Mohammad Abujubbeh, Abdulaziz Almalaq, Mohamed A. Mohamed

Mechanical Engineering Graduate Research

Recently, many renewable energy (RE) initiatives around the world are based on general frameworks that accommodate the regional assessment taking into account the mismatch of supply and demand with pre-set goals to reduce energy costs and harmful emissions. Hence, relying entirely on individual assessment and RE deployment scenarios may not be effective. Instead, developing a multi-faceted RE assessment framework is vital to achieving these goals. In this study, a regional RE assessment approach is presented taking into account the mismatch of supply and demand with an emphasis on Photovoltaic (PV) and wind turbine systems. The study incorporates mapping of renewable …

Design Of Smart Trashcan, Haoran Song

Senior Theses

A smart trashcan has been designed which can bring convenience to people for throwing their garbage away during the COVID-19 pandemic. A prototype is made from cardboard to demonstrate its function. This trashcan can sense people who are coming and leaving, and it can open and close automatically. The trashcan is powered by solar energy. A solar panel is mounted on top of the trashcan supporter. This design is specifically for use in China.

Pore Microstructure Impacts On Lithium Ion Transport And Rate Capability Of Thick Sintered Electrodes, Ziyang Nie, Rohan Parai, Chen Cai, Charles Michaelis, Jacob M. Lamanna, Daniel S. Hussey, David L. Jacobson, Dipankar Ghosh, Gary M. Koenig Jr.

Mechanical & Aerospace Engineering Faculty Publications

Increasing electrode thickness is one route to improve the energy density of lithium-ion battery cells. However, restricted Li⁺ transport in the electrolyte phase through the porous microstructure of thick electrodes limits the ability to achieve high current densities and rates of charge/discharge with these high energy cells. In this work, processing routes to mitigate transport restrictions were pursued. The electrodes used were comprised of only active material sintered together into a porous pellet. For one of the electrodes, comparisons were done between using ice-templating to provide directional porosity and using sacrificial particles during processing to match the geometric density …