Power and Energy Commons^™

Design Of High Efficiency Doherty Power Amplifier, Kobi G. Kelly, Severin Pindell

Electrical Engineering

The project includes design and fabrication of a high efficiency power amplifier for a student design competition held at International Microwave Symposium (IMS) 2023. Efficient power amplifiers are critical for base station communication requiring efficient use of available power. The final design optimizes power added efficiency (PAE) and linearity. The amplifier will operate at 2.45 GHz. Competitive PAE above 50%, and C/I above 30 dB is achieved by leveraging a Doherty class amplifier using accurate discrete CGH4006P transistor models to simulate an efficient and linear design. Unique design features include optimal transistor bias point selection and power split ratios between …

Fourier Analysis And Optimization Of Inductive Wireless Power Transfer For Electric Vehicle Charging, Andrew P. Foote

Doctoral Dissertations

With the growth of electric vehicle (EV) popularity, different charging options to increase user convenience and reduce charging time such as high power wireless charging are increasingly being developed and researched. Inductive wireless power transfer (WPT) systems for EVs must meet specifications such as stray field, battery power and voltage operating range, efficiency, and ground clearance. The coil geometry and design have a large impact in meeting these constraints. Typical design approaches include iterative analysis of predetermined coil geometries to identify candidates that meet these constraints.

This work instead directly generates WPT coil shapes and magnetic fields to meet specifications …

Gpu Based Monte Carlo Estimation Of Eddy Current Losses In Electromagnetic Coil-Core System, Adwaith Ravichandran

Theses and Dissertations

A novel parallelizable probabilistic approach to model eddy currents in AC electromagnets is presented in this research. Consequently, power loss associated with the formation of these eddy currents is estimated and validated using experimental data. Furthermore, predicting the effect of ferromagnetic alternating field enhancement on power loss in the source excitation winding has been an active area of research. Unlike a stationary field, an alternating sinusoidal field diffuses partially into the ferromagnetic material leading to a predictably sub-optimal field enhancement. To model these physics, finite element techniques employ nonlinear iterative solvers which are time consuming. A novel method is developed …

Design, Modeling, And Testing Of A Novel Inductor For Electric Vehicles: Iron Nitride Soft Magnetic Composites, Sydney F. Fultz-Waters, Jacob Krynock

Materials Engineering

New technology for electric vehicles (EVs) must meet the requirements of higher energy usage, lower costs, and more sustainable source materials. One promising material for EV power system components is iron nitride (IN) soft magnetic composites (SMCs) because of their competitive magnetic properties and high abundance of the source materials. As part of an ongoing program at Sandia National Laboratories, this project focused on using computer modeling to optimize the prototyping process for an iron nitride SMC toroidal inductor to reach a target inductance of 600 μH. Four inductors with different combinations of wiring (26 AWG and 20 AWG) and …

Wireless Energy Harvesting System, Matthew Palma, Audrey Toop, Andrew Fahey

Electrical Engineering

The modern world is built upon wireless transmission of data. The signals that carry this data travel through the air, an untapped source of power. Unreceived transmissions are dissipated into useless forms of energy when they should be reclaimed. Wireless electronics can theoretically be powered by harvesting energy from the electromagnetic signals in the wireless internet frequency band. The aim of this project is to develop a system to capture ambient energy, convert it into DC power, and store the power for later use. The product will consist of three subsystems: an antenna receiver, a rectifier and voltage-multiplier, and a …

Multiple Objective Co-Optimization Of Switched Reluctance Machine Design And Control, Timothy Burress

Doctoral Dissertations

This dissertation includes a review of various motor types, a motivation for selecting the switched reluctance motor (SRM) as a focus of this work, a review of SRM design and control optimization methods in literature, a proposed co-optimization approach, and empirical evaluations to validate the models and proposed co-optimization methods.

The switched reluctance motor (SRM) was chosen as a focus of research based on its low cost, easy manufacturability, moderate performance and efficiency, and its potential for improvement through advanced design and control optimization. After a review of SRM design and control optimization methods in the literature, it was found …

Multiple Output Power Supply Using Toroidal Transformers For Medium Voltage Active Gate Drivers, Samhitha Venkata Machireddy

Graduate Theses and Dissertations

When operating in high power applications, power devices dissipate tens or hundreds of watts of power in the form of heat. The ability of the power devices to withstand power and dissipation of heat across the power devices becomes a prominent requirement in designing the power converter. This challenge demands a power converter design to be more effective and consistent which factors in size, cost, weight, power density and reliability. This study aims to propose a gate driver isolated power supply design that can be used in medium voltage applications (e.g., up to 10 kV) while respecting the principle of …

Classification Of Electrical Current Used In Electroplastic Forming, Tyler Grimm

All Dissertations

Electrically assisted manufacturing (EAM) is the direct application of an electric current to a workpiece during manufacturing. This advanced manufacturing process has been shown to produce anomalous effects which extend beyond the current state of modeling of thermal influences. These purported non-thermal effects have collectively been termed electroplastic effects (EPEs).

While there is a distinct difference in results between steady-state (ideal DC) testing and pulsed current testing, the very definition of these two EAM methods has not been well established. A "long" pulse may be considered DC current; a "short" pulse may produce electroplastic effects; and even "steady-state" current shapes …

Wireless Power Transfer In Autonomous Mobile Microgrids, Carl Greene

Dissertations, Master's Theses and Master's Reports

The ability to autonomously dock unmanned ground vehicles plays a key role in mobile micro-grids, where efficient power transfer is paramount. The approach utilized in this work allows for near-field wireless power transfer in remote locations with minimal support. Establishing a micro-grid power system connection autonomously using wireless power eliminates the arduous task of designing a complex, multiple degrees of freedom (MDOF) robotic arm. The work presented in this thesis focuses on both the hardware and software within the micro-grid system. This particular near-field wireless system consists of a primary and secondary set of modules, comprised of Litz wire coils, …

The Effect Of A Ferrite-Core Relay Vs. An Air-Core Relay On The Output Power Characteristics Of A Three-Coil Wireless Power Transfer System, Jakob L. White

University Honors Theses

The purpose of this thesis is to determine the effect of using a ferrite-core relay on the output power characteristics of a three-coil, parallel-tuned, domino-resonator wireless power transfer (WPT) system in comparison to the effect of using an air-core relay in such a system. First, a general mathematical model is presented to describe both the ferrite-core-relay system and the air-core-relay system and to calculate their output power characteristics for seven different resistive loads at each of five different distance configurations between the coils. Next, experimental results are analyzed and compared to the mathematical results to confirm model accuracy. Finally, the …

Use Of The Igbt Module In The Active Region To Design A High Current Active Filter, Jorge F. Galarraga

Graduate Theses and Dissertations

Particle accelerators require high-precision magnetic fields on the order or 100ppm or less. This implies that the precision of the associated electrical current in the electromagnet that generates these fields should be smaller than 100ppm. However, conventional switching power supplies cannot offer this precision due to the frequency limitation of the switches. This research considers the use of power electronics devices operating in a linear as an alternative solution to meet the requirements of particle accelerator electromagnets.

This thesis presents the study of an insulated-gate bipolar transistor (IGBT) driver using a new control method that linearizes the IGBT’s collector-emitter voltage …

Si-Based Germanium Tin Photodetectors For Infrared Imaging And High-Speed Detection, Huong Tran

Graduate Theses and Dissertations

Infrared (IR) radiation spans the wavelengths of the windows: (1) near-IR region ranging from 0.8 to 1.0 μm, (2) shortwave IR (SWIR) ranging from 1.0 to 3.0 μm, (3) mid-wave IR (MWIR) region covering from 3.0 to 5.0 μm, (4) longwave IR (LWIR) spanning from 8.0 to 12.0 μm, and (5) very longwave IR extending beyond 12.0 μm. The MWIR and LWIR regions are important for night vision in the military, and since the atmosphere does not absorb at these wavelengths, they are also used for free-space communications and astronomy. Automotive and defect detection in the food industry and electronic …

A Magneto-Mechanical Piezoelectric Energy Harvester Designed To Scavenge Ac Magnetic Field From Thermal Power Plant With Power-Line Cables, Quan Wang, Kyung-Bum Kim, Sang-Bum Woo, Yooseob Song, Tae-Hyun Sang

Civil Engineering Faculty Publications and Presentations

Piezoelectric energy harvesters have attracted much attention because they are crucial in portable industrial applications. Here, we report on a high-power device based on a magneto-mechanical piezoelectric energy harvester to scavenge the AC magnetic field from a power-line cable for industrial applications. The electrical output performance of the harvester (×4 layers) reached an output voltage of 60.8 V_max, an output power of 215 mW_max (98 mW_rms), and a power density of 94.5 mW_max/cm³ (43.5 mW_rms/cm³) at an impedance matching of 5 kΩ under a magnetic field of 80 …

Specification, Control, And Applications Of Z-Source Circuit Breakers For The Protection Of Dc Power Networks, Sagar Bhatta

Electrical & Computer Engineering Theses & Dissertations

There is a highly-increasing demand for the DC power transmission and distribution in modern power systems for the integration of newly-installed renewable energy resources and storage systems to the existing utilities. Application of DC power systems in electric ships, battery energy devices, high-voltage DC networks, smart grids, electric vehicles, microgrids, and wind farms is a recent trend that is being highly investigated. The fault protection of DC systems is an essential but challenging issue that needs careful attention to maintain system operation reliability and device safety. In this research, the specification, control, and application of Z-source breakers (ZCBs) are investigated …

Ultrafast Thermal Modification Of Strong Coupling In An Organic Microcavity, Bin Liu, Vinod M. Menon, Matthew Y. Sfeir

Publications and Research

There is growing interest in using strongly coupled organic microcavities to tune molecular dynamics, including the electronic and vibrational properties of molecules. However, very little attention has been paid to the utility of cavity polaritons as sensors for out-of-equilibrium phenomena, including thermal excitations. Here, we demonstrate that non-resonant infrared excitation of an organic microcavity system induces a transient response in the visible spectral range near the cavity polariton resonances. We show how these optical responses can be understood in terms of ultrafast heating of electrons in the metal cavity mirror, which modifies the effective refractive index and subsequently the strong …

On-Chip Nonreciprocal Components For Full-Duplex Communications And Gaussian Regulated Gate Driver For Electromagnetic Interference Reduction, Chang Yang

Electrical Engineering Theses and Dissertations

This dissertation is comprised of two unrelated design endeavors. The first one is about two CMOS nonreciprocal components: 1) an isolator and 2) a circulator. To make the components compact enough for the next generation communication systems with wide bandwidth, both components operate at 100 GHz band for full-duplex transceivers for ultra-high-data-rate millimeter-wave wireless communication. The proposed nonreciprocal structures are based on a time-domain modulation by signals at around 1/6 of the RF frequencies and spatial duplexing over the RF signal paths, demonstrating over 45 dB isolation in a bandwidth of 1.5 GHz over the tuning range of 85-110 GHz. …

Conducted Emi Mitigation In Power Converters Using Active Emi Filters, Balaji Narayanasamy

Graduate Theses and Dissertations

Wide bandgap devices enable high power density power converters. Despite the advantages of increased switching frequency, the passive components are still a major bottleneck towards enabling high power density. Among the passive components in the converter, the passive EMI filters are unavoidable to ensure compliance with conducted EMI standards. Active EMI filters help reduce the volume of the passive components and have been around for three decades now. Firstly, this work presents a summary of all the different active EMI filters based on the type of noise-sensing, noise-processing, the type of active circuits used and the type of control methods. …

Evaluating The Effects Of Electric And Magnetic Loading On The Performance Of Single And Double Rotor Axial Flux Pm Machines, Narges Taran, Greg Heins, Vandana Rallabandi, Dean Patterson, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

Axial flux PM (AFPM) machines are used particularly in applications requiring a compact structure. Their disc shape topology and axial air-gap have led to a variety of configurations including two popular ones: the yokeless and segmented armature (YASA), and the single-stator single rotor or single sided machine. In this study, a comprehensive comparative analysis of these configurations is conducted at different magnetic and electric loadings. It is found that at lower loadings, typically employed for air-cooled machines, the torque/ampere characteristics of the YASA machine are almost identical to those of a single sided machine constructed with half the magnet volume. …

Performance Enhancement And Characterization Of An Electromagnetic Railgun, Paul M. Gilles

Master's Theses

Collision with orbital debris poses a serious threat to spacecraft and astronauts. Hypervelocity impacts resulting from collisions mean that objects with a mass less than 1g can cause mission-ending damage to spacecraft. A means of shielding spacecraft against collisions is necessary. A means of testing candidate shielding methods for their efficacy in mitigating hypervelocity impacts is therefore also necessary. Cal Poly’s Electromagnetic Railgun was designed with the goal of creating a laboratory system capable of simulating hypervelocity (≥ 3 km/s) impacts. Due to several factors, the system was not previously capable of high-velocity (≥ 1 km/s) tests. A deficient projectile …

High Frequency Ltcc Based Planar Transformer, Adithya Venkatanarayanan

Graduate Theses and Dissertations

As we move towards high power and higher frequency related technology, conventional wire-wound magnetics have their own limitations which has led path to the development of planar based magnetic materials. Nowadays more planar magnetic technology has been employed because it is easier to fabricate them. The planar magnetic is a transformer or an inductor that replaces the wire-wound transformer or inductors which generally uses copper wires. One of the main reasons why we move to planar magnetic technology is its operation at higher frequency which provides higher power density. This study explains in detail about the design and fabrication of …

Design And Analysis Of Modular Axial Flux Switched Reluctance Motor, Rochak Shiwakoti

University of New Orleans Theses and Dissertations

This thesis presents a new modular structure of the axial flux Switched Reluctance Motor (SRM). The design consists of four stator disks with each adjacent disk rotated 30 degrees apart and four rotor disks connected to a common shaft. The proposed design aims to reduce the unwanted radial force, mitigate the torque ripple, and improve the efficiency. The modular structure distributes the radial force and torque strokes along the axial length of the motor, potentially damping the torque pulsation. In addition, the modular structure would deliver the rating power at a lower current level, reducing the overall ohmic loss. Moreover, …

Triple-Junction Solar Cells : In Parallel., Levi C Mays

Electronic Theses and Dissertations

This paper looks into the current inefficiency of solar cells and attempts a few alternative solar cell structures in order to provide a more effective source of renewable energy. Currently, multi-junction solar cells are being developed to capture the sun’s light more efficiently. One of the ideas in this paper is to add a window to see if the addition of such a layer into a junction will increase the voltage while maintaining nearly the same current output. Central to this paper is the rearranging of the conducting layers of the multi-junction cell so that the junctions can be connected …

Dc-Dc Converter For Electric Vehicle, Jason Y. Zhou, Nicholas James Mah

Electrical Engineering

In this work, a DC-DC converter is designed for an electric vehicle. The DC-DC converter is designed to provide 500W with a 200-400V input and a 12-15V adjustable output. Electric vehicle sales are beginning to increase in popularity and the need for DC-DC converters to siphon power from the tractive system is not yet fully satisfied, especially for single-seater class vehicles. Additionally, improving performance in efficiency without sacrificing wide input voltage range can benefit future DC-DC converter designs. In the end, a forward active clamp DC-DC converter is designed and tested. Additionally, spreadsheet calculators, LTSpice simulations, and Matlab scripts were …

Optical And Electrical Analysis Of Zno/Znte Micropillar Solar Cells, Sadia Binte Sohid

Master’s Theses

The prime focus of the energy-research community in recent times has been replacing fossil fuels with renewable energy. Therefore, photovoltaic research areas are rapidly expanding in this era. The purpose of this work is to compare three different structural ZnO/ZnTe solar cell types (planar, axial micropillar and radial micropillar). The best optical and electrical performance has been obtained by the radial junction (core-shell) ZnO/ZnTe micropillar solar cell due to its pillar structure and radial junction. The unique advantage of the radial junction micropillar is that the angle of the incident light and the carrier collection is orthogonal. Therefore, the pillar …

Optimum Design Of Axial Flux Pm Machines Based On Electromagnetic 3d Fea, Narges Taran

Theses and Dissertations--Electrical and Computer Engineering

Axial flux permanent magnet (AFPM) machines have recently attracted significant attention due to several reasons, such as their specific form factor, potentially higher torque density and lower losses, feasibility of increasing the number of poles, and facilitating innovative machine structures for emerging applications. One such machine design, which has promising, high efficiency particularly at higher speeds, is of the coreless AFPM type and has been studied in the dissertation together with more conventional AFPM topologies that employ a ferromagnetic core.

A challenge in designing coreless AFPM machines is estimating the eddy current losses. This work proposes a new hybrid analytical …

Optimal Design Of A Switched Reluctance Motor With Magnetically Disconnected Rotor Modules Using A Design Of Experiments Differential Evolution Fea-Based Method, Vandana Rallabandi, Jie Wu, Ping Zhou, David G. Dorrell, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

Switched reluctance (SR) machines are attractive because they present relatively high efficiency and torque density in spite of lacking permanent magnets. This paper focuses on a two-objective optimization of an external rotor SR motor with a stator that has concentrated coils and a rotor with magnetically isolated modules. The objectives are minimum loss and mass, and 11 independent dimensionless geometric variables are considered as inputs that affect them. A combined design of experiments (DOE) and differential evolution (DE) approach is proposed. The DOE methodology is used to reduce the search space by eliminating from consideration input variable values, leading to …

Two-Level Surrogate-Assisted Differential Evolution Multi-Objective Optimization Of Electric Machines Using 3-D Fea, Narges Taran, Dan M. Ionel, David G. Dorrell

Power and Energy Institute of Kentucky Faculty Publications

A two-level surrogate-assisted optimization algorithm is proposed for electric machine design using 3-D finite-element analysis (FEA). The algorithm achieves the optima with much fewer FEA evaluations than conventional methods. It is composed of interior and exterior levels. The exploration is performed mainly in the interior level, which evaluates hundreds of designs employing affordable kriging models. Then, the most promising designs are evaluated in the exterior loop with expensive 3-D FEA models. The sample pool is constructed in a self-adjustable and dynamic way. A hybrid stopping criterion is used to avoid unnecessary expensive function evaluations.

Hybrid Perovskite Characterization And Device Applications., Kasun Fernando

Electronic Theses and Dissertations

Hybrid perovskites are a group of materials that has shown a great impact in the field of scientific research in the past decade due to the efficiency gain within a short period of time. Hot casting is one technique that has been producing high efficient and stable solar cells. Electrical transportation of lateral device structure by such film is explored to understand basic properties and predict possible device applications using it. Under dark, memristive ability of the film was explored using various experiments. Unique uni-polar memristor ability was observed. Using the experimental results, a model is hypothesized using the concepts …

Wind Turbine Design: Analysis And Experimentation Of Electro-Magnetic Alternator Design, Mark Hans Ewald Steinke

Honors Projects

This article explores the alternator designs for small scale wind turbines and the aspects that affect the performance of these alternators. It explores the design and testing process used to quantify, visualize, and understand the relationship between the wind turbine stator design and the performance. Additionally, the paper analyzes the data collection method using a test jig powered by a hydraulic motor set up by previous groups of students and the data intended to be collected using actual field tests on Whidbey Island located at Camp Casey. These tests were intended to identify favorable combinations of alternators and blades. However, …

Analysis Of Photovoltaic Energy In The Eastern Kentucky Region And The Residential Financial Feasibility, Joshua A. Johnson

Morehead State Theses and Dissertations

A thesis proposal presented to the Faculty of the College of Business and Technology Morehead State University in partial fulfillment of the requirements for the Degree Master of Science by Joshua A. Johnson on April 25, 2018.