Electronic Devices and Semiconductor Manufacturing Commons^™

Piezoelectric Actuator Driver System, Daniel Hoefer

Electrical Engineering

This work presents the design, fabrication, and testing of a high-voltage piezoelectric actuator driver system purposed for integration into defense and aerospace precision motion control applications, particularly those in laser optics. The core challenge addressed was the mismatch between the standardized 28V DC power bus used in military systems and the significantly higher voltage requirements of piezoelectric actuators. Existing commercial drivers were evaluated and found unsuitable for field deployment due to inadequate ruggedness, excessive complexity, or power limitations. Consequently, a modular system architecture was designed featuring four independent driver channels, each using a high-voltage, high-current linear amplifier topology to scale …

Void-Semiconductor Gaas Photonic Crystal Surface-Emitting Lasers By Epitaxial Regrowth And Single-Epitaxy Methods, Kevin James Reilly

Nanoscience and Microsystems ETDs

Monolithic semiconductor lasers including edge-emitting lasers (EELs) and vertical-cavity surface-emitting lasers (VCSELs) fail to realize simultaneous achievement of both high-power high-quality beams due to intrinsic limitations of their resonant cavity. Photonic crystal surface emitting lasers (PCSELs) address these structural limitations through employment of a two-dimensional photonic crystal (PC) cavity that creates feedback at a single wavelength for laterally scalable devices. This function of the PC allows PCSELs to power scale with area while maintaining single-mode emission required for diffraction-limited beams. In this way, PCSELs fulfill an industry demand for high-power high-quality lasing from a single chip.

Early PCSELs were fabricated …

Fourier Transform Infrared Spectroscopy For The Measurement Of Gesn/(Si)Gesn, Solomon Opeyemi Ojo

Graduate Theses and Dissertations

Photoluminescence (PL) and Electroluminescence (EL) characterization techniques are important tools for studying the optical and electrical properties of (Si)GeSn. Light emission from these PL and EL measurements provides relevant information on material quality, bandgap energy, current density, and device efficiency. Prior to this work, the in-house PL set-up of this lab which involves the use of a commercially-obtained dispersive spectrometer was used for characterizing both GeSn thin film and fabricated devices, but these measurements were limited by issues bordering on low spectral resolution, spectral artifacts, and poor signal-to-noise ratio (SNR) thereby resulting in the possible loss of vital information and …

The Photoluminescence Spectra Of Powders Of Zinc Oxide With Laser Excitation, Ilyos A. Rakhmatullaev, Vladimir S. Gorelik, Abdulla K. Kurbonov

Euroasian Journal of Semiconductors Science and Engineering

The original sensitive method of research of the nanopowders based on use of laser excitation and a multichannel spectrometer is offered. The developed method can be used for the analysis of quality of a wide class of the powders on the basis of laser spectroscopy of secondary radiation.

The Photoluminescence Spectra Of Powders Of Zinc Oxide With Laser Excitation, Ilyos A. Rakhmatullaev, Vladimir S. Gorelik, Abdulla K. Kurbonov

Euroasian Journal of Semiconductors Science and Engineering

The original sensitive method of research of the nanopowders based on use of laser excitation and a multichannel spectrometer is offered. The developed method can be used for the analysis of quality of a wide class of the powders on the basis of laser spectroscopy of secondary radiation.

Laser Cursor, Michael Liman

Electrical Engineering

A user controls a cursor on a computer screen using a laser pointer.  A camera picks up the laser pointer’s position and sends the data to the computer to move the cursor in the correct position.

Optimization Of Gan Laser Diodes Using 1d And 2d Optical Simulations, Sean Richard Keali'i Jobe

Master's Theses

This paper studies the optical properties of a GaN Laser Diode (LD). Through simulation, the GaN LD is optimized for the best optical confinement factor. It is found that there are optimal thicknesses of each layer in the diode that yield the highest optical confinement factor. There is a strong relationship between the optical confinement factor and lasing threshold—a higher optical confinement factor results in a lower lasing threshold. Increasing optical confinement improves lasing efficiency. Blue LDs are important to the future of lighting sources as they represent the final color in the RGB spectrum that does not have a …