Electronic Devices and Semiconductor Manufacturing Commons^™

Universality Of Non-Ohmic Shunt Leakage In Thin-Film Solar Cells, Sourabh Dongaonkar, Jonathan D. Servaites, Grayson M. Ford, Stephen Loser, James E. Moore, Ryan M. Gelfand, Hooman Mohseni, Hugh W. Hillhouse, Rakesh Agrawal, Mark A. Ratner, Tobin J. Marks, Mark Lundstrom, Muhammad A. Alam

Birck and NCN Publications

We compare the dark current-voltage (IV) characteristics of three different thin-film solar cell types: hydrogenated amorphous silicon (a-Si:H) p-i-n cells, organic bulk heterojunction (BHJ) cells, and Cu(In,Ga)Se₂ (CIGS) cells. All three device types exhibit a significant shunt leakage current at low forward bias (V< ∼ 0.4) and reverse bias, which cannot be explained by the classical solar cell diode model. This parasitic shunt current exhibits non-Ohmic behavior, as opposed to the traditional constant shunt resistance model for photovoltaics. We show here that this shunt leakage (I_sh), across all three solar cell types considered, is characterized by the following common phenomenological features: (a) voltage symmetry about V = 0, (b) nonlinear (power law) voltage dependence, and (c) extremely weak temperature dependence. Based on this analysis, we provide a simple method of subtracting this shunt current component from …

Modeling The Random Component Of Manufacturing Yield Of Integrated Circuits., David L. Farnsworth, Michael E. Long

Articles

A model is created for the number of integrated circuits that are good from each wafer on which they are fabricated. The goal is to separate the random or common cause loss from the systematic or special loss. The random loss from this type of process is modeled so that false alarms indicating systematic loss are less likely to occur and so that the structure of the systematic loss can be determined.

An Investigation Of Carrier Transport In Hafnium Oxide/Silicon Dioxide Mos Gate Dielectric Stacks From 5.6-400k, Richard G. Southwick Iii

Boise State University Theses and Dissertations

Hafnium oxide (HfO₂) is replacing silicon dioxide (SiO₂) as the gate dielectric in metal oxide semiconductor (MOS) structures driven mainly by need to reduce high leakage currents observed in sub-2nm SiO₂. The high dielectric constant of HfO₂ (~25) compared to SiO₂ (3.9 bulk) allows a thicker HfO₂ layer to be used in place of the thinner SiO₂ layer thereby reducing the gate leakage current in MOS devices while maintaining the same capacitive coupling provided by the thinner SiO₂. However, incorporating HfO₂ into MOS devices produces a SiO …

Mems-Based Pufs For Cryptographic Applications, Nicholas Shane Patrick

Honors Capstone Projects and Theses

No abstract provided.

Application Of Signal Advance Technology To Electrophysiology, Chris M. Hymel

Dissertations and Theses (Open Access)

Medical instrumentation used in diagnosis and treatment relies on the accurate detection and processing of various physiological events and signals. While signal detection technology has improved greatly in recent years, there remain inherent delays in signal detection/ processing. These delays may have significant negative clinical consequences during various pathophysiological events. Reducing or eliminating such delays would increase the ability to provide successful early intervention in certain disorders thereby increasing the efficacy of treatment.

In recent years, a physical phenomenon referred to as Negative Group Delay (NGD), demonstrated in simple electronic circuits, has been shown to temporally advance the detection of …

The Applications And Limitations Of Printable Batteries, Matthew Delmanowski

Graphic Communication

This study focuses on the potential applications for printed batteries and how they could affect the printing industry. It also analyzes the main problems associated with manufacturing this technology and what needs to be done to overcome these issues. To find the answers to these questions, two methods of research were used. The first was through the elite and specialized interviewing of Dr. Scott Williams of Rochester Institute of Technology and Professor Nancy Cullins from Cal Poly. The second form of research was a common, yet useful, method called secondary research. This entailed looking at recent written research papers about …

Enhanced Light Extraction Efficiency From Gan Light Emitting Diodes Using Photonic Crystal Grating Structures, Simeon S. Trieu

Master's Theses

Gallium nitride (GaN) light emitting diodes (LED) embody a large field of research that aims to replace inefficient, conventional light sources with LEDs that have lower power, higher luminosity, and longer lifetime. This thesis presents an international collaboration effort between the State Key Laboratory for Mesoscopic Physics in Peking University (PKU) of Beijing, China and the Electrical Engineering Department of California Polytechnic State University, San Luis Obispo. Over the course of 2 years, Cal Poly’s side has simulated GaN LEDs within the pure blue wavelength spectrum (460nm), focusing specifically on the effects of reflection gratings, transmission gratings, top and bottom …

Negative Conductance Load Modulation Rf Power Amplifier, Cody R. Neslen

Master's Theses

The number of mobile wireless devices on the market has increased substantially over the last decade. The frequency spectrum has become crowded due to the number of devices demanding radio traffic and new modulation schemes have been developed to accommodate the number of users. These new modulation schemes have caused very poor efficiencies in power amplifiers for wireless transmission systems due to high peak-to-average power ratios (PAPR). This thesis first presents the issue with classical power amplifiers in modern modulation systems. A brief overview of current attempts to mitigate this issue is provided. A new RF power amplifier topology is …

Production Of Multiwall Carbon Nanotuse For Alcohol Sensor Application., Ebtehal Saleh Alshaqaq

Student Works (2010-2019)

Multiwall carbon nanotube/polyethylene oxide (PEO), multiwall carbon nanoube/polyvinyl alcohol(PVA) and multiwall carbon nanotube/ polyvinyl alcohol(PVA)/zinc oxide(ZnO) have been tested as chemical sensors and detailed study on the effect of different gas concentration and material properties on gas sensitivity is presented. Initial composites were prepared by a simple solution casting and characterized by x-ray diffraction for ZnO, Fourier transform infra-red spectroscopy (FTIR) and scanning electron microscopy (SEM) to demonstrate crystallite size of ZnO, the morphology and surface area respectively. On the other hand, MWCNT/PEO , MWCNT/PVA , MWCNT/PVA/ZnO were prepared with different loading MWCNT and ZnO. The chemical sensing properties of …

Vibrational Frequencies Of Magnetic Random Access Memory Materials., Lee Li Ling

Student Works (2010-2019)

The advantages of MRAM are so overwhelming which acts as motivation for scientist in further investigation for better read and write operation. The types of materials used are closely related to the cell performance in forming the ferromagnetic layers. Thus,the vibrational frequencies of the MRAM materials are of interest. Clusters for the two types of combinations, FexNiy and FexCoyBz are built. Subsequently, vibrational frequencies of each cluster are calculated theoretically from the first principles. The secular determinant is large when the number of electrons in a cluster is large. For the simplest combination of Fe-Ni cluster, (atomic number of an …

Investigation Of Rf Curing Parameters In Resin Infusion Molding, Christopher K. Love

Theses and Dissertations

The purpose of this study is to investigate RF or Radio Frequency energy as a viable alternative to traditional heating methods for the purpose of curing resins used in resin infusion molding, a molding system for polymeric composites. Traditional heating/curing methods include technologies such as room temperature, oven, microwave, infrared, and ultraviolet. Although RF curing provides far more advantages than disadvantages, its implementation into a manufacturing process can be challenging. Specifically, three critical elements must be present in order for RF to function in a manner that is profitable to the manufacturer. Those elements are: (1) the proper generator (voltage …

High Power Microwave (Hpm) And Ionizing Radiation Effects On Cmos Devices, Nicholas A. Estep

Theses and Dissertations

Integrated circuits (ICs) are inherently complicated and made worse by increasing transistor quantity and density. This trend potentially enhances concomitant effects of high energy radiation and local or impressed electromagnetic interference (EMI). The reduced margin for signal error may counter any gain in radiation hardness from smaller device dimensions. Isolated EMI and ionizing radiation studies on circuits have been conducted extensively over the past 30 years. However, little focus has been placed on the combined effects. To investigate the effect of combined EMI and ionizing radiation, two complementary metal oxide semiconductor (CMOS) inverter technologies (CD4069 and SN74AUC1G04) were analyzed for …

Development And Demonstration Of A Field-Deployable Fast Chromotomographic Imager, Daniel C. O'Dell

Theses and Dissertations

A field deployable hyperspectral imager utilizing chromotomography (CT), with a direct vision prism (DVP) as the dispersive element, has been constructed at AFIT. This research is focused on the development and demonstration of the CT imager. An overview of hyperspectral imaging, chromotomography, a synopsis of reconstruction algorithms, and other CT instruments are given. The importance of component alignment, instrument calibration, and exact prism angular position data are discussed. A simplistic \shift and add" reconstruction algorithm was utilized for this research. Although limited in its ability to reconstruct a spatially and spectrally diverse scene, the algorithm was adequate for the testing …

Wi-Fi Evapotranspiration Irrigation Controller, Ryan Goodman

Electrical Engineering

This report discusses the applications of an Irrigation Controller with Wi-Fi connectivity, with focus on cost-effectiveness and usability. It addresses the amount to which traditional irrigation is wasteful, and proposes solutions to solve this problem. Methods for using online weather data resources to increase efficiency of residential landscaping are discussed in depth. Included is the procedural development of an irrigation controller using the Microchip Explorer 16 Development Board and TCP/IP Stack. Also discussed is web hosting and use of the scripting language PHP, and database MySQL. This project found inexpensive means for providing HTTP and FTP services. Results indicate an …

Theory Of ‘Selectivity’ Of Label-Free Nanobiosensors – A Geometro-Physical Perspective, Pradeep R. Nair, Muhammad A. Alam

Birck and NCN Publications

Modern label-free biosensors are generally far more sensitive and require orders of magnitude less incubation time compared to their classical counterparts. However, a more important characteristic regarding the viability of this technology for applications in Genomics/Proteomics is defined by the ‘Selectivity’, i.e., the ability to concurrently and uniquely detect multiple target biomolecules in the presence of interfering species. Currently, there is no theory of Selectivity that allows optimization of competing factors and there are few experiments to probe this problem systematically. In this article, we use the elementary considerations of surface exclusion, diffusion limited transport, and void distribution function to …

Nano-Scaled Fet Device For Cmos Technology, Prabhat Ranjan Pathak

Dissertations

In this work the 3-D structure of the Accumulation mode (ACM) and Enhance mode (ECM) FinFET was developed by the Taurus-Device Editor. The design of both ACM and ECM FinFET was optimized for high-performance IC applications to meet ITRS specification for I_off current, for 9nm gate length. The design of ACM and ECM FinFET is optimized, analyzed and compared against each other with respect to Darin Induced Barrier Lower (DIBL), Sub-threshold Swing(SS), operation and performance characteristics with varying electrical and physical parameters Silicon thickness (T_si), Source/Drain doping gradient (σ_sd), electrical channel length (L_eff ), …

Production Of Multiwall Carbon Nanotube For Alcohol Sensor Application., Ebtehal Saleh Alshaqaq

Student Works (2010-2019)

Multiwall carbon nanotube/polyethylene oxide (PEO), multiwall carbon nanoube/polyvinyl alcohol(PVA) and multiwall carbon nanotube/ polyvinyl alcohol(PVA)/zinc oxide(ZnO) have been tested as chemical sensors and detailed study on the effect of different gas concentration and material properties on gas sensitivity is presented. Initial composites were prepared by a simple solution casting and characterized by x-ray diffraction for ZnO, Fourier transform infra-red spectroscopy (FTIR) and scanning electron microscopy (SEM) to demonstrate crystallite size of ZnO, the morphology and surface area respectively. On the other hand, MWCNT/PEO , MWCNT/PVA , MWCNT/PVA/ZnO were prepared with different loading MWCNT and ZnO. The chemical sensing properties of …

Inductively Coupled Plasma Dry Etching Process On Planar Lightwave Circuit Fabrication., Chuah Khoon Seah

Student Works (2010-2019)

The main objective of this project is to master state-of-the-art techniques and knowledge in silica etching in order to achieve high quality waveguide circuit on Planar Lightwave Circuit devices. Another objective is to optimize the clean room research strength, surface characterization, microscopy techniques and similar semiconductor manufacturing processes.Initially, these processes were conducted with wet etching method that utilized diluted hydrofluoric acid (HF) and buffered oxide etch (BOE). Several problems arising such as mask peel-off, poor sidewall profile and defect waveguide channel during the pattern transfer process due to its’ isotropic nature. Alternatively, dry etching method was conducted via Inductively Coupled …

Excitation-Induced Germanium Quantum Dot Formation On Si (100)-(2×1), Ali Oguz Er, Hani E. Elsayed-Ali

Physics Faculty Publications

The effect of nanosecond pulsed laser excitation on the self-assembly of Ge quantum dots grown by pulsed laser deposition on Si (100)-(2×1) was studied. In situ reflection high-energy electron diffraction and ex situ atomic force microscopy were used to probe the quantum dot structure and morphology. At room temperature, applying the excitation laser decreased the surface roughness of the grown Ge film. With surface electronic excitation, crystalline Ge quantum dots were formed at 250 °C, a temperature too low for their formation without excitation. At a substrate temperature of 390 °C, electronic excitation during growth was found to improve the …

Optimization Of Inductively Coupled Plasma Dry Etching For Planar Waveguide Fabrication., Lim Weng Hong

Student Works (2010-2019)

Optimization of the Inductively Coupled Plasma (ICP) dry etching process parameters has been carried out. Seven main etching characteristics were considered in order to produce good etching quality. These characteristics are glass etching rates, selectivity of chromium to glass etching rate, channel side wall roughness, channel side wall vertical profile, channel cleanliness, critical dimension and resolution. Several ICP parameters that are affecting the etching characteristic were optimized in this work. These optimised ICP parameters obtained from this work are ICP power (880 W), bias power (45 W), operating chamber pressure (10 mtorr), reactant gas composition, reactant gas flow rate (35sccm …

Giant Raman Enhancement On Nanoporous Gold Film By Conjugating With Nanoparticles For Single-Molecule Detection, Lihua Qian, Biswajit Das, Yan Li, Zhilin Yang

Electrical & Computer Engineering Faculty Research

Hot spots have the contradictively geometrical requirements for both the narrowest interstices to provide strong near-field coupling, and sufficient space to allow entrance of the analytes. Herein, a two-step method is employed to create hot spots within hybrid nanostructures, which consist of self-supported nanoporous gold films with the absorbed probes and subsequent nanoparticle conjugates without surface agents or mechanical motion. The molecules confined into 1 nm interstice exhibit 2.9 × 10⁷ times enhancement in Raman scattering compared to pure nanoporous gold. Giant enhancement primarily results from strong near-field coupling between nanopore and nanoparticle, which is theoretically confirmed by finite-difference …

Growth And Characterization Of Silicon Carbide Thin Films Using A Nontraditional Hollow Cathode Sputtering Technique, James Huguenin-Love

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Silicon carbide (SiC) is considered a suitable candidate for high-power, high-frequency devices due to its wide bandgap, high breakdown field, and high electron mobility. It also has the unique ability to synthesize graphene on its surface by subliming Si during an annealing stage. The deposition of SiC is most often carried out using chemical vapor deposition (CVD) techniques, but little research has been explored with respect to the sputtering of SiC.

Investigations of the thin film depositions of SiC from pulse sputtering a hollow cathode SiC target are presented. Although there are many different polytypes of SiC, techniques are discussed …