Electromagnetics and Photonics Commons^™

A Tunable Electromagnetic Band-Gap Microstrip Filter, Greg A. Lancaster

Master's Theses

In high frequency design, harmonic suppression is a persistent struggle. Non-linear devices such as switches and amplifiers produce unwanted harmonics which may interfere with other frequency bands. Filtering is a widely accepted solution, however there are various shortcomings involved. Suppressing multiple harmonics, if desired, with traditional lumped element and distributed component band-stop filters requires using multiple filters. These topologies are not easily made tunable either. A new filter topology is investigated called Electromagnetic Band-Gap (EBG) structures.

EBG structures have recently gained the interest of microwave designers due to their periodic nature which prohibits the propagation of certain frequency bands. EBG …

The Effect Of Polarization And Ingan Quantum Well Shape In Multiple Quantum Well Light Emitting Diode Heterostructures, Patrick M. Mcbride

Master's Theses

Previous research in InGaN/GaN light emitting diodes (LEDs) employing semi-classical drift-diffusion models has used reduced polarization constants without much physical explanantion. This paper investigates possible physical explanations for this effective polarization reduction in InGaN LEDs through the use of the simulation software SiLENSe. One major problem of current LED simulations is the assumption of perfectly discrete transitions between the quantum well (QW) and blocking layers when experiments have shown this to not be the case. The In concentration profile within InGaN multiple quantum well (MQW) devices shows much smoother and delayed transitions indicative of indium diffusion and drift during …

3d Electromagnetic Simulation Tool Exposure For Undergraduate Electrical Engineers: Incorporation Into An Analog Filters Course, Bobby B. Pheng

Master's Theses

With the growth of wireless communications, comes the need for engineers knowledgeable in 3D electromagnetic (EM) simulation of high-frequency circuits. To give electrical engineering students a better understanding of the behavior of electromagnetic fields, experiments including the use of 3D EM simulation software were proposed. Most students get lost in differential equations, curls, and divergences; this thesis aims to remedy that by exposing them to 3D EM simulation, which may motivate them toward further study in electromagnetics. Also, experience using EMPro is very beneficial for future RF/microwave/antenna engineers, as use of 3D EM simulation is becoming a requirement for this …

Light Extraction Enhancement Of Gan Based Leds Using Top Gratings, Patterned Sapphire Substrates, And Reflective Surfaces, Greg Chavoor

Master's Theses

In the last 15 years, an immense amount of research has gone into developing high efficiency Gallium Nitride based light emitting diodes (LED). These devices have become increasingly popular in LED displays and solid state lighting. Due to the large difference in refractive index between GaN and Air, a significant amount of light reflects at the boundary and does not escape the device. This drawback decreases external quantum efficiency (EQE) by minimizing light extraction. Scientists and engineers continue to develop creative solutions to enhance light extraction. Some solutions include surface roughening, patterned sapphire substrates, and reflective layers.

This study proposes …

Polar Field Oriented Control With 3rd Harmonic Injection, Martin Todd Hess

Master's Theses

Abstract

POLAR FIELD-ORIENTED CONTROL

with

3^RD HARMONIC INJECTION

Martin Todd Hess

Field Oriented Control (FOC), also known as vector control, is a widely used and well documented method for controlling Permanent-Magnet Synchronous Motors (PMSM) and induction motors. Almost invariably the orientation of the stator and rotor (field) fluxes are described in rectangular coordinates. In this thesis we explore the practicality of using polar coordinates.

Third harmonic injection is also a well-known technique that allows full utilization of the bus (DC-link), thus allowing the motor to run to full base speed without the use of field weakening. This technique potentially …

902–928mhz Uhf Rfid Tag Antenna Design, Fabrication And Test, Chiweng Kam

Master's Theses

Radio Frequency Identification (RFID) uses RF radiation to identify physical objects. With decreasing integrated circuit (IC) cost and size, RFID applications are becoming economically feasible and gaining popularity. Researchers at MIT suggest that RFID tags operating in the 900 MHz band (ultrahigh frequency, UHF) represent the best compromise of cost, read range, and capabilities [1]. Passive RFID tags, which exclude radio transmitters and internal power sources, are popular due to their small size and low cost [1].

This project produced Cal Poly’s first ever on-campus printed, assembled, and operational UHF (902 to 928 MHz) passive RFID tag. Project goals include …

Enhanced Light Extraction Efficiency From Gan Light Emitting Diodes Using Photonic Crystal Grating Structures, Simeon S. Trieu

Master's Theses

Gallium nitride (GaN) light emitting diodes (LED) embody a large field of research that aims to replace inefficient, conventional light sources with LEDs that have lower power, higher luminosity, and longer lifetime. This thesis presents an international collaboration effort between the State Key Laboratory for Mesoscopic Physics in Peking University (PKU) of Beijing, China and the Electrical Engineering Department of California Polytechnic State University, San Luis Obispo. Over the course of 2 years, Cal Poly’s side has simulated GaN LEDs within the pure blue wavelength spectrum (460nm), focusing specifically on the effects of reflection gratings, transmission gratings, top and bottom …

Aperture Coupled Microstrip Antenna Design And Analysis, Michael Paul Civerolo

Master's Theses

A linearly-polarized aperture coupled patch antenna design is characterized and optimized using HFSS antenna simulation software. This thesis focuses on the aperture coupled patch antenna due to the lack of fabrication and tuning documentation for the design of this antenna and its usefulness in arrays and orthogonally polarized communications. The goal of this thesis is to explore dimension effects on aperture coupled antenna performance, to develop a design and tuning procedure, and to describe performance effects through electromagnetic principles.

Antenna parameters examined in this study include the dimensions and locations of the substrates, feed line, ground plane coupling slot, and …

Improved Rf Power Extraction From 1.55um Ge-On-Soi Pin Photodiodes With Load Impedance Optimization, Andrew L. Huard

Master's Theses

VLSI miniaturization has created the need for high-density, low-cost, monolithically-integrated optical interconnects. High output power photodetectors are needed to directly drive load circuitry, which improves the noise performance and dynamic range of optical communications links by eliminating a post amplifier stage. Elimination of the post amplifier also reduces circuit cost and complexity. A new Si-Ge PIN waveguide photodiode with 31GHz bandwidth and 93% quantum efficiency at 1550nm has been developed by Yin et al., which was fabricated using standard CMOS processes on a Silicon substrate. This thesis demonstrates a method for improving the RF power extraction from these photodiodes by …

Standalone Antenna Demonstration System, Alexander James Hempy

Master's Theses

Antenna systems play a significant role in today’s electronic communications. They are essential for cell phones, satellites, radio, and radar among many other important applications. This paper describes the design, assembly, and operation of an antenna demonstration system designed to instill interest in the field of antenna design among high school and undergraduate college students. The system is portable, supplied solely by DC power supplies, easily reproducible, and includes rotational axes to illustrate antenna performance limitations and requirements. It provides a visual indication of wireless signal strength and demonstrates several antenna performance characteristics including polarization, gain and directivity, radiation patterns …

Swept-Frequency Sampled Grating Distributed Bragg Reflector Lasers Optimized For Optical Coherence Tomography Applications, Brandon J. George

Master's Theses

Swept Frequency Source Optical Coherence Tomography (OCT) requires high repetition rate and wide spectral width wavelength tunable sources at a low cost. The sampled grating distributed Bragg reflector (SG-DBR) laser provides wide wavelength tuning range while exhibiting a wavelength switching speed that is among the fastest currently available. The SG-DBR laser is used to generate linear frequency ramps with high repetition rates. Since the SG-DBR laser is currently used for the telecommunications industry in high volume, the price of the system is much lower than current OCT sources. Therefore the SG-DBR laser provides a practical solution for Swept Source OCT. …

Synthetic Aperture Radar Imaging Simulated In Matlab, Matthew Schlutz

Master's Theses

This thesis further develops a method from ongoing thesis projects with the goal of generating images using synthetic aperture radar (SAR) simulations coded in MATLAB. The project is supervised by Dr. John Saghri and sponsored by Raytheon Space and Airborne Systems. SAR is a type of imaging radar in which the relative movement of the antenna with respect to the target is utilized. Through the simultaneous processing of the radar reflections over the movement of the antenna via the range Doppler algorithm (RDA), the superior resolution of a theoretical wider antenna, termed synthetic aperture, is obtained. The long term goal …

Shielding Effectiveness Of Superalloy, Aluminum, And Mumetal Shielding Tapes, Cindy Suit Cheung

Master's Theses

Using MIL-HDBK-419A, MATLAB and Nomographs, Shielding Effectiveness for the Magnetic Field, Electric Field, and Plane Wave were calculated over a frequency range from 10 Hz to 1 GHz. The three shielding tapes used included superalloy, aluminum, and mumetal. Calculations for Shielding Effectiveness involve the computation of Absorption Loss, Reflection Loss, and Re-Reflection Correction Factor. From the outcome of the calculations, it was suitable to conclude that all three metals fulfill the 40 dB Shielding Effectiveness requirements for SGEMP fields for frequencies greater or equal to 1 MHz. Accordingly, all three shielding tapes provide at least 40 dB of shielding to …

High Speed Wavelength Tuning Of Sgdbr Lasers For Optical Coherence Tomography Applications, Benjamin Maher

Master's Theses

The application of Sample Grated Distributed Bragg Reflector (SGDBR) wavelength tunable lasers for swept-wavelength Optical Coherence Tomography (OCT) is explored. OCT is a method of measuring reflectivity versus distance into samples under test with a focused infrared light source. Swept wavelength OCT requires a laser light source that is capable of sweeping its wavelength quickly over the entire wavelength range of the tunable laser. Fast sweeping of the laser's wavelength enables real-time imaging of a wide surface area of the surface under test. This thesis will show that SGDBR lasers can be designed to meet the fast wavelength ramp speeds …