Electromagnetics and Photonics Commons^™

Characterization Of The Nonlinear Refractive Index Of Carbon Disulfide Over An Extended Spectral And Temporal Range, Marcus Seidel

Electronic Theses and Dissertations

The intensity dependent refractive index change of a medium is frequently described in terms of the product n₂ · I where n₂ is the nonlinear refractive index and I the light intensity. The nonlinear refractive index is often treated as constant which is a reasonable assumption if the light interacts only with bound electrons. In the case of carbon disulfide (CS₂) however, nuclear motions contribute to n₂. These motions occur on the sub picosecond time scale and thus become especially relevant for ultrashort laser pulses. The neat liquid CS₂ is studied because it exhibits a large nonlinear refractive index in …

Low Noise And Low Repetition Rate Semiconductor-Based Mode-Locked Lasers, Dimitrios Mandridis

Electronic Theses and Dissertations

The topic of this dissertation is the development of low repetition rate and low noise semiconductor-based laser sources with a focus on linearly chirped pulse laser sources. In the past decade chirped optical pulses have found a plethora of applications such as photonic analogto-digital conversion, optical coherence tomography, laser ranging, etc. This dissertation analyzes the aforementioned applications of linearly chirped pulses and their technical requirements, as well as the performance of previously demonstrated chirped pulse laser sources. Moreover, the focus is shifted to a specific application of the linearly chirped pulses, timestretched photonic analog-to-digital conversion (TS ADC). The challenges of …

Design, Fabrication, And Testing Of High-Transparency Deep Ultra-Violet Contacts Using Surface Plasmon Coupling In Subwavelength Aluminum Meshes, Clarisse Mazuir

Electronic Theses and Dissertations

The present work aims at enhancing the external quantum efficiencies of ultra-violet (UV) sensitive photodetectors (PDs) and light emitting diodes (LEDs)for any light polarization. Deep UV solid state devices are made out of AlGaN or MgZnO and their performances suffer from the high resistivity of their p-doped regions. They require transparent p-contacts; yet the most commonly used transparent contacts have low transmission in the UV: indium tin oxide (ITO) and nickel-gold (Ni/Au 5/5 nms) transmit less than 50% and 30% respectively at 300 nm. Here we investigate the use of surface plasmons (SPs) to design transparent p-contacts for AlGaN devices …

Performance Measures In Acousto-Optic Chaotic Signal Encryption System Subject To Parametric Variations And Additive Noise, Monish Ranjan Chatterjee, Anjan K. Ghosh, Mohammed A. Al-Saedi

Electrical and Computer Engineering Faculty Publications

Signal encryption and recovery using chaotic optical waves has been a subject of active research in the past 10 years. Since an acousto-optic Bragg cell with zeroth- and first-order feedback exhibits chaotic behavior past the threshold for bistability, such a system was recently examined for possible chaotic encryption using a low-amplitude sinusoidal signal applied via the bias input of the sound cell driver.

Subsequent recovery of the message signal was carried out via a heterodyne strategy employing a locally generated chaotic carrier, with threshold parameters matched to the transmitting Bragg cell. The simulation results, though encouraging, were limited to relatively …

Consideration Of Dispersion And Group Velocity Dispersion In The Determination Of Velocities Of Electromagnetic Propagation, Monish Ranjan Chatterjee, Partha P. Banerjee

Electrical and Computer Engineering Faculty Publications

Electromagnetic (EM) propagation velocities play an important role in the determination of power and energy flow in materials and interfaces. It is well known that group and phase velocities need to be in opposition in order to achieve negative refractive index.

Recently, we have shown that considerable differences may exist in phase, group and signal/energy velocities for normal and anomalous dispersion, especially near dielectric resonances. This paper examines the phase and group velocities in the presence of normal and anomalous dispersion, and group velocity dispersion (GVD), which requires introduction of the second order coefficient in the permittivity and permeability models.

Response-Calibration Techniques For Antenna-Coupled Infrared Sensors, Peter Krenz

Electronic Theses and Dissertations

Infrared antennas are employed in sensing applications requiring specific spectral, polarization, and directional properties. Because of their inherently small dimensions, there is significant interaction, both thermal and electromagnetic, between the antenna, the antenna-coupled sensor, and the low-frequency readout structures necessary for signal extraction at the baseband modulation frequency. Validation of design models against measurements requires separation of these effects so that the response of the antenna-coupled sensor alone can be measured in a calibrated manner. Such validations will allow confident extension of design techniques to more complex infrared-antenna configurations. Two general techniques are explored to accomplish this goal. The extraneous …

Fast-Response Liquid Crystal Displays, Meizi Jiao

Electronic Theses and Dissertations

After about five decades of extensive material research and device development, followed by massive investment in manufacturing technology, thin-film-transistor liquid-crystaldisplay (TFT-LCD) has finally become the dominant flat panel display technology. Nowadays, LCD performances, such as viewing angle, contrast ratio, and resolution, have reached acceptable levels. The remaining major technical challenges are response time, light efficiency, and sunlight readability. Fast response time is desired to reduce motion blur and to enable field sequential color displays using red (R), green (G), and blue (B) LEDs (light emitting diodes) without noticeable color breakup. Sequential RGB colors would eliminate the commonly used spatial color …

Long Cavity Quantum Dot Laser Diode And Monolithic Passively Mode-Locked Operation, K Shavitranuruk

Electronic Theses and Dissertations

Advantage of the single QD active layer is its potential for very low threshold current density, which in turn can produce low internal optical loss. The low threshold current density and low internal loss thus enable a significant increase in laser diode cavity length. Because of the importance of the threshold current density in heatsinking, future technology of broad-area monolithic laser diodes can be implemented. The dissertation describes the development and the unique characteristics of single QD active layer laser with long cavity. The data are presented on single layer QD laser diodes that reach threshold current densities values of …

Fabrication Of Integrated Optofluidic Circuits In Chalcogenide Glass Using Femtosecond Laser Direct Writing, Troy P. Anderson

Electronic Theses and Dissertations

Femtosecond laser direct writing (FLDW) is a versatile process that uses focused femtosecond pulses to modify the physical structure of a material, which can result in a shift of optical properties such as the linear and nonlinear refractive index. If the photon energy of the femtosecond pulses lies below the material bandgap, nonlinear absorption rather than linear absorption becomes the dominant mechanism of energy transfer to the material. In this manner, a focused femtosecond pulse train can be used to fabricate functional features such as optical waveguides, diffractive optical elements, or micro-fluidic elements within the volume of a transparent medium. …

Nonlinear Absorption And Free Carrier Recombination In Direct Gap Semiconductors, Peter D. Olszak

Electronic Theses and Dissertations

Nonlinear absorption of Indium Antimonide (InSb) has been studied for many years, yet due to the complexity of absorption mechanisms and experimental difficulties in the infrared, this is still a subject of research. Although measurements have been made in the past, a consistent model that worked for both picosecond and nanosecond pulse widths had not been demonstrated. In this project, temperature dependent two-photon (2PA) and free carrier absorption (FCA) spectra of InSb are measured using femtosecond, picosecond, and nanosecond IR sources. The 2PA spectrum is measured at room temperature with femtosecond pulses, and the temperature dependence of 2PA and FCA …

Plasmon Enhanced Near-Field Interactions In Surface Coupled Nanoparticle Arrays For Integrated Nanophotonic Devices, Amitabh Ghoshal

Electronic Theses and Dissertations

The current thrust towards developing silicon compatible integrated nanophotonic devices is driven by need to overcome critical challenges in electronic circuit technology related to information bandwidth and thermal management. Surface plasmon nanophotonics represents a hybrid technology at the interface of optics and electronics that could address several of the existing challenges. Surface plasmons are electronic charge density waves that can occur at a metal-dielectric interface at optical and infrared frequencies. Numerous plasmon based integrated optical devices such as waveguides, splitters, resonators and multimode interference devices have been developed, however no standard integrated device for coupling light into nanoscale optical circuits …

New Laser Technologies Analysis Of Quantum Dot And Lithographic Laser Diodes, Abdullah Demir

Electronic Theses and Dissertations

The first part of this dissertation presents a comprehensive study of quantum dot (QD) lasers threshold characteristics. The threshold temperature dependence of a QD laser diode is studied in different limits of p-doping, hole level spacing and inhomogeneous broadening. Theoretical analysis shows that the threshold current of a QD laser in the limit of uniform QDs is not temperature independent and actually more temperature sensitive than the quantum well laser. The results also explain the experimental trends of negative characteristic temperature observed in QD lasers and clarify how the carrier distribution mechanisms inside and among the QDs affect the threshold …

Application Of Antenna Synthesis And Digital Signal Processing Techniques For Active Millimeter-Wave Imaging Systems, Wilson Ariel Caba

Electronic Theses and Dissertations

Millimeter-wave imaging has gathered attention in recent years for its ability to penetrate clothing, thin layers of soils, and certain construction materials. However, image quality remains a challenge that needs to be addressed. One way of improving image quality is by increasing the dimensions of the collecting aperture. A sparse array can be used to synthesize a larger aperture with a limited set of relatively small detectors. In this research we design, build, and test a test-bed having an active source at 94 GHz and an array of coherent detectors, mounted on arms that extend radially on a rotary table. …

Modeling And Design Of A Photonic Crystal Chip Hosting A Quantum Network Made Of Single Spins In Quantum Dots That Interact Via Single Photons, Hubert P. Seigneur

Electronic Theses and Dissertations

In this dissertation, the prospect of a quantum technology based on a photonic crystal chip hosting a quantum network made of quantum dot spins interacting via single photons is investigated. The mathematical procedure to deal with the Liouville-Von Neumann equation, which describes the time-evolution of the density matrix, was derived for an arbitrary system, giving general equations. Using this theoretical groundwork, a numerical model was then developed to study the spatiotemporal dynamics of entanglement between various qubits produced in a controlled way over the entire quantum network. As a result, an efficient quantum interface was engineered allowing for storage qubits …

Design And Simulation Of Silica-On-Silicon Pump/Signal Multiplexer For Hybrid Passive-Active Optical Devices., Alvin Law Wen Pin

Student Works (2010-2019)

This dissertation describes the design and simulation of silica-on-silicon pump/signal multiplexer for hybrid passive-active optical devices. Uniform symmetric directional couplers and planar Bragg gratings were utilized in this work, forming the essential building blocks in a waveguide amplifier. Several designs in relation to the multiplexers are presented in this work, with the simplest application for the directional coupler as a pump/signal multiplexer. A 980/1550 nm and an 800/1310 nm pump/signal multiplexers for erbium doped and bismuth doped waveguide amplifier, respectively were modeled. These couplers were designed and simulated in Rsoft BeamPROP environment, utilizing 3D Finite Difference Beam Propagation Method (FD-BPM) …

Nonlinear Fiber Lasers Using Bismuth Based Erbium Doper Fiber Amplifier., Sharifeh Shahi

Student Works (2010-2019)

A thorough study on Bismuth-based Erbium-doped fiber (Bi-EDF) is presented for wide-band amplifiers and multi-wavelength fiber laser applications. This fiber allows high Erbium ions concentration to be doped without a significant concentration quenching effect. The high refractive index characteristic in the Bi-EDF has broadened the emission spectrum of Erbium ions to achieve a broader gain spectrum up to extended L-band region compared to normal silica-based Erbium-doped fiber (EDF). The Bi-EDFA performances have been investigated in terms of power conversion efficiency (PCE), quantum conversion efficiency (QCE), gain and noise figure. The highest QCE and PCE for a 215 cm long of …

Reflective And Beam-Through Types Of Fiber Optic Sensor For Displacement Measurement., Walaa Fawzi Al–Masri

Student Works (2010-2019)

This dissertation proposes and demonstrates fiber-optic displacement sensor (FODS) theoretically and experimentally using the intensity modulation technique to measure a displacement from a probe and target. The sensor uses a multimode plastic bundled fiber as a probe and He-Ne laser as a source. The performance of the sensor is compared for different type of probe and target. For a pair type bundled fiber, both the experimental and theoretical results exhibit the same type of characteristic features. The front slope sensitivities are obtained at 1.71 and 1.0 mW/μm for the theoretical and experimental approaches respectively, while the back slope sensitivities are …

Harvesting Single Ferroelectric Domain Stressed Nanoparticles For Optical And Ferroic Applications, Gary Cook, J. L. Barnes, S. A. Basun, Dean R. Evans, Ron F. Ziolo, Arturo Ponce, Victor Yu. Reshetnyak, Anatoliy Glushchenko, Partha P. Banerjee

Electrical and Computer Engineering Faculty Publications

We describe techniques to selectively harvest single ferroelectric domain nanoparticles of BaTiO3 as small as 9 nm from a plethora of nanoparticles produced by mechanical grinding. High resolution transmission electron microscopy imaging shows the unidomain atomic structure of the nanoparticles and reveals compressive and tensile surface strains which are attributed to the preservation of ferroelectric behavior in these particles.

We demonstrate the positive benefits of using harvested nanoparticles in disparate liquid crystal systems.

Characterization Of Atmospheric Turbulence Effects Over 149 Km Propagation Path Using Multi-Wavelength Laser Beacons, Mikhail Vorontsov, Gary W. Carhart, Venkata S. Rao Gudimetla, Thomas Weyrauch, Eric Stevenson, Svetlana Lachinova, Leonid A. Beresnev, Jony Jiang Liu, Karl Rehder, Jim F. Riker

Electrical and Computer Engineering Faculty Publications

We describe preliminary results of a set of laser beam propagation experiments performed over a long (149 km) near-horizontal propagation path between Mauna Loa (Hawaii Island) and Haleakala (Island of Maui) mountains in February 2010. The distinctive feature of the experimental campaign referred to here as the Coherent Multi-Beam Atmospheric Transceiver (COMBAT) experiments is that the measurements of the atmospheric-turbulence induced laser beam intensity scintillations at the receiver telescope aperture were obtained simultaneously using three laser sources (laser beacons) with different wavelengths (λ1 = 0.53 μm, λ2 = 1.06 μm, and λ3 = 1.55 μm). The presented experimental results on …

Development Of Optical Coherence Tomography For Tissue Diagnostics, Panomsak Meemon

Electronic Theses and Dissertations

Microvasculature can be found in almost every part of the human body, including the internal organs. Importantly, abnormal changes in microvasculature are usually related to pathological development of the tissue cells. Monitoring of changes in blood flow properties in microvasculature, therefore, provides useful diagnostic information about pathological conditions in biological tissues as exemplified in glaucoma, diabetes, age related macular degeneration, port wine stains, burn-depth, and potentially skin cancer. However, the capillary network is typically only one cell in wall thickness with 5 to 10 microns in diameter and located in the dermis region of skin. Therefore, a non-invasive flow imaging …

The Development Of Scalable Pump Techniques For Gg Iag Fiber Lasers And Passive Athermalization Techniques For Solid State Laser, William Hageman

Electronic Theses and Dissertations

This dissertation consists of two parts: research pertaining to the development of scalable pump techniques for gain guided index-antiguided fiber lasers and research relating to the development of passive athermalization schemes for solid state lasers. The first section primarily details the development of a side pump scheme that allows for power scaling of gain-guided index anti-guided fibers. While these fibers have been demonstrated in past research, none have used a pump technology capable of pumping with the efficiencies, uniformity, and necessary length to allow for scaling of the fiber lasers to high output powers. The side pumped scheme developed in …

Freeform Reflector Design With Extended Sources, Florian Fournier

Electronic Theses and Dissertations

Reflector design stemmed from the need to shape the light emitted by candles or lamps. Over 2,000 years ago people realized that a mirror shaped as a parabola can concentrate light, and thus significantly boosts its intensity, to the point where objects can be set afire. Nowadays many applications require an accurate control of light, such as automotive headlights, streetlights, projection displays, and medical illuminators. In all cases light emitted from a light source can be shaped into a desired target distribution with a reflective surface. Design methods for systems with rotational and translational symmetry were devised in the 1930s. …

Quantum Dot Based Mode-Locked Semiconductor Lasers And Applications, Jimyung Kim

Electronic Theses and Dissertations

In this dissertation, self-assembled InAs/InGaAs quantum dot Fabry-Perot lasers and mode-locked lasers are investigated. The mode-locked lasers investigated include monolithic and curved two-section devices, and colliding pulse mode-locked diode lasers. Ridge waveguide semiconductor lasers have been designed and fabricated by wet etching processes. Electroluminescence of the quantum dot lasers is studied. Cavity length dependent lasing via ground state and/or excited state transitions is observed from quantum dot lasers and the optical gain from both transitions is measured. Stable optical pulse trains via ground and excited state transitions are generated using a grating coupled external cavity with a curved two-section device. …

Electro-Optical And All-Optical Switching In Multimode Interference Waveguides Incorporating Semiconductor Nanostructures, Nathan Bickel

Electronic Theses and Dissertations

The application of epitaxially grown, III-V semiconductor-based nanostructures to the development of electro-optical and all-optical switches is investigated through the fabrication and testing of integrated photonic devices designed using multimode interference (MMI) waveguides. The properties and limitations of the materials are explored with respect to the operation of those devices through electrical carrier injection and optical pumping. MMI waveguide geometry was employed as it offered advantages such as a very compact device footprint, low polarization sensitivity, large bandwidth and relaxed fabrication tolerances when compared with conventional single-mode waveguide formats. The first portion of this dissertation focuses on the characterization of …

Accelerating Optical Airy Beams, Georgios Siviloglou

Electronic Theses and Dissertations

Over the years, non-spreading or non-diffracting wave configurations have been systematically investigated in optics. Perhaps the best known example of a diffraction-free optical wave is the so-called Bessel beam, first suggested and observed by Durnin et al. This work sparked considerable theoretical and experimental activity and paved the way toward the discovery of other interesting non-diffracting solutions. In 1979 Berry and Balazs made an important observation within the context of quantum mechanics: they theoretically demonstrated that the Schrodinger equation describing a free particle can exhibit a non-spreading Airy wavepacket solution. This work remained largely unnoticed in the literature-partly because such …

Misalignment Induced Nodal Aberration Fields And Their Use In The Alignment Of Astronomical Telescopes, Tobias Schmid

Electronic Theses and Dissertations

Following the foundation of aberration theory for rotationally symmetric optical systems established by Seidel, Schwarzschild, Burch, Conrady, Buchdahl, and in its most useful form H.H. Hopkins, Shack, Buchroeder, Thompson, and Rogers developed a vectorial form of the wave aberration theory that enables addressing optical systems without symmetry. In this research, a vectorial theory is utilized and extended for the alignment of two- and three-mirror astronomical telescopes, including the effects of pointing changes and astigmatic figure errors. Importantly, it is demonstrated that the vectorial form of aberration theory, also referred to as nodal aberration theory, not only provides valuable insights but …

Near-Field Optical Interactions And Applications, David Haefner

Electronic Theses and Dissertations

The propagation symmetry of electromagnetic fields is affected by encounters with material systems. The effects of such interactions, for example, modifications of intensity, phase, polarization, angular spectrum, frequency, etc. can be used to obtain information about the material system. However, the propagation of electromagnetic waves imposes a fundamental limit to the length scales over which the material properties can be observed. In the realm of near-field optics, this limitation is overcome only through a secondary interaction that couples the high-spatial-frequency (but non-propagating) field components to propagating waves that can be detected. The available information depends intrinsically on this secondary interaction, …

Epitaxial Growth, Characterization And Application Of Novel Wide Bandgap Oxide Semiconductors, Jeremy Mares

Electronic Theses and Dissertations

In this work, a body of knowledge is presented which pertains to the growth, characterization and exploitation of high quality, novel II-IV oxide epitaxial films and structures grown by plasma-assisted molecular beam epitaxy. The two compounds of primary interest within this research are the ternary films NixMg1-xO and ZnxMg1-xO and the investigation focuses predominantly on the realization, assessment and implementation of these two oxides as optoelectronic materials. The functioning hypothesis for this largely experimental effort has been that these cubic ternary oxides can be exploited - and possibly even juxtaposed - to realize novel wide band gap optoelectronic technologies. The …

Micro-Electro-Mechanical Systems (Mems) And Agile Lensing-Based Modules For Communications, Sensing And Signal Processing., Syed Reza

Electronic Theses and Dissertations

This dissertation proposes the use of the emerging Micro-Electro-Mechanical Systems (MEMS) and agile lensing optical device technologies to design novel and powerful signal conditioning and sensing modules for advanced applications in optical communications, physical parameter sensing and RF/optical signal processing. For example, these new module designs have experimentally demonstrated exceptional features such as stable loss broadband operations and high > 60 dB optical dynamic range signal filtering capabilities. The first part of the dissertation describes the design and demonstration of digital MEMS-based signal processing modules for communication systems and sensor networks using the TI DLP (Digital Light Processing) technology. Examples of …

Fast Response Dual Frequency Liquid Crystal Materials, Qiong Song

Electronic Theses and Dissertations

Dual frequency liquid crystal (DFLC) exhibits a positive dielectric anisotropy at low frequencies and negative dielectric anisotropy at high frequencies. The frequency where dielectric anisotropy is zero is called crossover frequency. DFLC can achieve fast rise time and fast decay time with the assistance of applied voltage. However, one drawback of DFLC is that it has dielectric heating effect when driven at a high frequency. Thus, the first part of this dissertation is to develop low crossover frequency DFLC materials. The dielectric relaxation and physical properties of some single- and double-ester compounds were investigated. Experimental results indicate that the double-ester …