Electrical and Electronics Commons^™

Ironless, Axial Flux, Electric Bldc Motor For Aircraft Electric Propulsion, Kevin W. Hobbs

Electrical Engineering Undergraduate Honors Theses

3D printing has shown much promise as a method of rapidly manufacturing lightweight ironless motors to meet the growing demand that airlines have for more cost-effective products that reduce emissions and flight prices. 3D-printed ironless, axial flux, electric BLDC motors would meet these needs with both their high efficiency and power density.

A Halbach array motor was designed and 3D-printed for the analysis of its magnetic properties to gain more insight about it performance. Fusion 360 was used to design the 3D drawings of the motor parts. The rotor, stator, and stator mount were designed to accommodate the sizes of …

Automated Bottling Station - Packaging System, Lauren Nicole Zinzilieta

Honors College Theses

This report focuses on the packaging system used at the end of the FESTO bottling station that is located in EP 2355. The system will be made up of an x-y 300 mm x 300 mm gantry system, an Arduino, two micro-stepping stepper drivers, and two 152.4 mm (6 in) single acting cylinders with a 3D printed bracket attached to both. The gantry system will be located at the end of the conveyor belt and will be programmed to pick up three bottles at a time and then will move a specified number of steps in both the x and …

Effect Of Silicon Carbide On Electric Drivetrains Of Heavy-Duty Vehicles, Haley Solera

Electrical Engineering Undergraduate Honors Theses

The application of electro-mechanical motors in rigorous, high-temperature systems is constantly adapting to suit the growing needs of developers in the automotive, construction, and aerospace industries. With improved efficiency, torque, and environmental impact over conventional internal combustion engines, electric drive trains pose more than ample incentive for manufacturers to invest considerable resources toward the design of newer, better methods of electric propulsion. This paper discusses the motives behind the electrification of heavy-duty vehicles, the state-of-the-art technology currently available on the market, and the novel application of silicon carbide to electric drive trains as a means of increasing their heat tolerance, …

Direct Drive Solar Panel Control Circuit, Marcorios Bekheit

Physics

A control circuit is built for insulated solar electric cookers (ISEC). Power delivery and temperature safety are the focus. Using a maximum power point tracking (MPPT) algorithm, Arduino Nano, voltage and current sensors, and a buck converter, the solar panel’s output power was maximized for a direct load heat resistor with 3.5Ω for a range of solar intensities. Using a resistance temperature detector, a temperature sensor is built for safety shutoff.

Discrepancy-Based Analysis Of Measurement Sampling Points In Compressive Sensing, Felipe Batista Da Silva

Open Access Theses & Dissertations

Compressive sensing (CS) is a technique in signal processing that under certain conditions allows someone to reconstruct sparse signals from fewer linear measurements. A problem in CS is modeled in terms of an underdetermined linear system, whose associated matrix is previously designed. Then, it is of interest in CS to know what a good sampling defined by the sensing matrix is and how to measure it. In this work, we provided analytical proofs of properties of the metric discrepancy that allow us to propose a fast algorithm for discrepancy calculation. Such metric measures the quality of the sampling measurement points …

An Open-Baffle Motional Feedback Loudspeaker, Matthew Quinlivan, William Harvie

Honors Theses

A dynamic loudspeaker mounted in an open baffle has the same parameters as a loudspeaker in free space. A subwoofer mounted in an open baffle has a small total quality factor and therefore the frequency above which the driver has a significant output is too high despite the subwoofer's low resonant frequency. To address this issue, we implemented a motional feedback circuit with the goal of introducing both velocity feedback and acceleration feedback into the loudspeaker system and thus altering the resonant frequency and total quality factor of the system. After verifying the efficacy of our feedback circuit with computer …

An 8-Bit Analog-To-Digital Converter For Battery Operated Wireless Sensor Nodes, Marvin Wayne Suggs Jr.

Graduate Theses and Dissertations

Wireless sensing networks (WSNs) collect analog information transduced into the form of a voltage or current. This data is typically converted into a digital representation of the value and transmitted wirelessly using various modulation techniques. As the available power and size is limited for wireless sensor nodes in many applications, a medium resolution Analog-to-Digital Converter (ADC) is proposed to convert a sensed voltage with moderate speeds to lower power consumption. Specifications also include a rail-to-rail input range and minimized errors associated with offset, gain, differential nonlinearity, and integral nonlinearity. To achieve these specifications, an 8-bit successive approximation register ADC is …

A Comparison Of Medical Article Transport Approaches, Andrew White

Honors Scholar Theses

Our senior design project is to develop a product named the Smartbox - a container capable of safely carrying and monitoring medical articles and accommodate a UAV drone carrying the container. These medical articles include sensitive medicines and human organs for transplantation. Speed, safety, and reliability are a must in this field, as the stakes if a payload is lost or improperly maintained can be life threatening. This project aims to improve on the existing medical transport logistics chains in use today. Time is the most important factor in transportation: many organs simply cannot survive outside of the human body …

Memory Module Design For High-Temperature Applications In Sic Cmos Technology, Affan Abbasi

Graduate Theses and Dissertations

The wide bandgap (WBG) characteristics of SiC play a significant and disruptive role in the power electronics industry. The same characteristics make this material a viable choice for high-temperature electronics systems. Leveraging the high-temperature capability of SiC is crucial to automotive, space exploration, aerospace, deep well drilling, and gas turbines. A significant issue with the high-temperature operation is the exponential increase in leakage current. The lower intrinsic carrier concentration of SiC (10-9 cm-3) compared to Si (1010 cm-3) leads to lower leakage over temperature. Several researchers have demonstrated analog and digital circuits designed in SiC. However, a memory module is …

Design And Assembly Of High-Temperature Signal Conditioning System On Ltcc With Silicon Carbide Cmos Circuits, Sajib Roy

Graduate Theses and Dissertations

The objective of the work described in this dissertation paper is to develop a prototype electronic module on a low-temperature co-fired ceramic (LTCC) material. The electronic module would perform signal conditioning of sensor signals (thermocouples) operating under extreme conditions for applications like gas turbines to collect data on the health of the turbine blades during operation so that the turbines do not require shutdown for inspection to determine if maintenance is required. The collected data can indicate when such shutdowns, which cost $1M per day, should be scheduled and maintenance actually performed. The circuits for the signal conditioning system within …

Neural Network For Monitoring Infant Feeding Process In The Smartbottle Device, Jiajun Guan

Master's Theses

To research the relationship between Childhood obesity and infant feeding patterns, the Electrical Engineering Department at California Polytechnic State University has designed a SmartBottle device attaching to the bottom of a baby bottle to monitor the infant feeding process. This project mainly focuses on the software and firmware design, as well as the neural network design of the SmartBottle device. The SmartBottle device is designed to identify infant feeding activities and to record related data for overweight and obesity research on children. This device includes a 6-dimensional inertial sensor that contains a 3-axis digital accelerometer and a 3-axis digital gyroscope. …

Analog Spiking Neural Network Implementing Spike Timing-Dependent Plasticity On 65 Nm Cmos, Luke Vincent

Graduate Theses and Dissertations

Machine learning is a rapidly accelerating tool and technology used for countless applications in the modern world. There are many digital algorithms to deploy a machine learning program, but the most advanced and well-known algorithm is the artificial neural network (ANN). While ANNs demonstrate impressive reinforcement learning behaviors, they require large power consumption to operate. Therefore, an analog spiking neural network (SNN) implementing spike timing-dependent plasticity is proposed, developed, and tested to demonstrate equivalent learning abilities with fractional power consumption compared to its digital adversary.

Performance And Economics Of Solar Inverters And Module Level Power Electronics In A 1 Mw Photovoltaic System, Maxwell Criswell

Biological and Agricultural Engineering Undergraduate Honors Theses

Photovoltaic solar panels convert sunlight to electricity in the form of direct current; therefore, a necessary component of every photovoltaic system is an inverter to convert the electricity to usable alternating current. There are various commercially available inverter technologies manufactured today such as microinverters, string inverters, and central inverters, as well as module level power electronic devices such as DC optimizers that are capable of improving system performance in string and central inverter systems. This thesis compares the performance and economics of five different inverter and module level power electronic systems through model simulation using Helioscope software. The five alternatives …

Raw Depth Image Enhancement Using A Neural Network, Xuan Xie

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The term image is often used to denote a data format that records information about a scene’s color. This dissertation object focuses on a similar format for recording distance information about a scene, “depth images”. Depth images have been used extensively in consumer-level applications, such as Apple’s Face ID, based on depth images for face recognition.

However, depth images suffer from low precision and high errors, and some post-processing techniques need to be utilized to improve their quality. Deep learning, or neural networks, are frameworks that use a series of hierarchically arranged nonlinear networks to process input data. Although each …

Husky Hand: A Low-Cost Electro-Mechanical Prosthetic Arm For The Underprivileged, Adam Robert

Thinking Matters Symposium

A continuation of a low-cost prosthetic upper limb prototype design which was investigated in EGN 301. The prosthetic is specifically designed for the needs and requirements of under privileged individuals in the Dominican Republic with upper limb amputations. The project focuses on the creation of an open-source computer aided prosthetic hand/arm model. The design allows consumer-grade fused filament fabrication (FFF) 3-D printers to be used. The improved design allows for the integration of the PQ-12 linear actuator for grasp and finger control. This simplifies the assembly, while, also reducing the size and mass of the whole unit. Producing a low-cost …

App Development For Wearable Sensors, Connor Pittman, Christopher Chappie, Patrick A. Tetreault

Thinking Matters Symposium

The objective of this research project was to create a wearable device that monitors bodily functions for the user to view on their smartphone. Sensor data is processed using the Arduino Nano 33 BLE microcontroller. The sensors used in this project include: proximity, temperature, humidity, heart rate, pressure, and skin impedance. This project takes advantage of the Arduino's Bluetooth low energy (BLE) capabilities so that all the data can be transmitted to a smartphone. This presentation shows the challenges faced during the project and how they were overcome. Some of these challenges include: programming, how heart rate sensors work, and …

Mems Directional Acoustic Sensors, Colby Damren

Thinking Matters Symposium

The purpose of my project is to test and verify two Micro-Electro-Mechanical-System (MEMS) microphones. The two MEMS devices are biomimetic microphones that imitate the eardrums of the Ormia Ochracea, a parasitic fly that listens for host crickets to lay their eggs. The MEMS microphones mimic the eardrum spacing of the Ormia Ochracea with a spacing of 1000um. This is roughly twice the opening of the Ormia Ochracea. The microphones will be tested for directionality inside a wooden box. This box will be lined with beveled foam to prevent any echo or outside noise from interfering with the results. These results …

Nitinol Robotic Arm, Brandon Cousino, Connor Sweatt

Thinking Matters Symposium

The goal of our project is to create a remotely controlled robotic arm using a nickel-titanium alloy (Nitinol) that exhibits “shape memory” tendencies and a 9-lumen tube. The arm must be able to move in all for directions (forward, left, right, backwards) with the control of a joystick and return to an upright position upon halting user input (thus requiring a two-way shape memory ability). The final product must operate without any unwanted twisting of the arm, crosstalk between the different nitinol wires due to heating, and be easily manufacturable. Easy replacement of the arm from the main mechanism is …

Design, Simulation And Testing Of Biomimetic Directional Acoustic Sensors, Brendan Francis

Thinking Matters Symposium

The Ormia ochracea, a species of parasitic fly, has become the focal point in sound localization research because of its finely tuned hearing abilities. The female of this species uses its super highly directional hearing to pinpoint the call of a host cricket, with hypersensitivity of frequency and phase difference, to reach and dispose of its eggs on the host. The goal of this study was to further the research of a previous Project in Professor Guvench’s group which implemented MEMS (Micro Electro-Mechanical System) technology on a chip to replicate these abilities. In this iteration, however, some commercially available …

Project Blipper, Peter Jacobs, Preston Delaware, Ryan Foster

Senior Design Project For Engineers

This project was sponsored by Clorox to design and create an automatic bottle-unscrambling system for possible implementation at their bottling plant in Chile. The objective was to use a robotic arm to unscramble bottles from an incoming conveyor belt and place them upright on an outbound conveyor belt. Throughout the research, design, and testing of solutions for this project, several design alternatives were found for each discipline, and will be presented to Clorox so that they can make an informed decision for how and if they want to move forward with implementation of this project.

The project was split into …

Kennesaw State University And United Alloy Corporation Robotic Pick And Place Project, Kathryn Bharadwaj, Logan Spencer, Tharkun Hudlow

Senior Design Project For Engineers

United Alloy Corporation (UAC), a company specializing in unique aluminum parts for aeronautics, needed a fix to their error prone, labor-intensive billet press operation. The process has a problem of adding the wrong size or wrong alloy billet to the induction oven, which results in a waste of raw materials. The billets range from ten to thirty-seven inches in length and weigh up to three hundred pounds. Currently, an operator uses a gantry crane to check and lift the billets from a rack onto the magazine of an induction oven. The magazine can hold up to three billets safely and …

Enercon Station Vacuum Pump Replacement, Clint Hembree, Jared D'Amico, Connor Moore, Paul Jeffrey Fontenot, Sydnee Castello, J.J. Clements

Senior Design Project For Engineers

This details the progress of the ENERCON pump replacement project as completed by the Kennesaw State University interdisciplinary senior design group. This project is a two-semester capstone effort for the engineering program at Southern Polytechnic School of Engineering, overseen by Dr. McFall during Fall 2020 and Dr. Khalid during Spring 2021 semesters. The 2020-2021 KSU Interdisciplinary Senior Design team was tasked with completing an Engineering Change Package (ECP) for existing vacuum pumps at ENERCON Station. The mechanical, electrical, and civil students worked together, performing evaluations on existing plant systems to ensure the plant could support the new vacuum pumps. By …

A Magneto-Mechanical Piezoelectric Energy Harvester Designed To Scavenge Ac Magnetic Field From Thermal Power Plant With Power-Line Cables, Quan Wang, Kyung-Bum Kim, Sang-Bum Woo, Yooseob Song, Tae-Hyun Sang

Civil Engineering Faculty Publications

Piezoelectric energy harvesters have attracted much attention because they are crucial in portable industrial applications. Here, we report on a high-power device based on a magneto-mechanical piezoelectric energy harvester to scavenge the AC magnetic field from a power-line cable for industrial applications. The electrical output performance of the harvester (×4 layers) reached an output voltage of 60.8 V_max, an output power of 215 mW_max (98 mW_rms), and a power density of 94.5 mW_max/cm³ (43.5 mW_rms/cm³) at an impedance matching of 5 kΩ under a magnetic field of 80 …

Suppressing Bias Stress Degradation In High Performance Solution Processed Organic Transistors Operating In Air, Hamna F. Iqbal, Qianxiang Ai, Karl J. Thorley, Hu Chen, Iain Mcculloch, Chad Risko, John E. Anthony, Oana D. Jurchescu

Chemistry Faculty Publications

Solution processed organic field effect transistors can become ubiquitous in flexible optoelectronics. While progress in material and device design has been astonishing, low environmental and operational stabilities remain longstanding problems obstructing their immediate deployment in real world applications. Here, we introduce a strategy to identify the most probable and severe degradation pathways in organic transistors and then implement a method to eliminate the main sources of instabilities. Real time monitoring of the energetic distribution and transformation of electronic trap states during device operation, in conjunction with simulations, revealed the nature of traps responsible for performance degradation. With this information, we …

Developing A Multimedia Interface For Electrical Biosignal Interpretation, Christopher Cox

Undergraduate Research and Scholarship Symposium

In the last ten years, a great deal of interest has been generated around the practice of using plants’ electrical signals to create sound or music. In order to render biosignals capable of producing sound electronically, some kind of interface is necessary that converts a plant’s natural electrical signals into data that a computer can understand. Existing commercial interfaces cost at minimum $3001,2 . Worse yet, two popular off-the-shelf interfaces conform their output signals to stereotypical human notions of what a plant might “sound like”. In this project we fabricated a simple but high-performance interface for less than $5 in …

Side Channel Attack Counter Measure Using A Moving Target Architecture, Jithin Joseph

Electrical and Computer Engineering ETDs

A novel countermeasure to side-channel power analysis attacks called Side-channel Power analysis Resistance for Encryption Algorithms using DPR or SPREAD is investigated in this thesis. The countermeasure leverages a strategy that is best characterized as a moving target architecture. Modern field programmable gate arrays (FPGA) architectures provide support for dynamic partial reconfiguration (DPR), a feature that allows real-time reconfiguration of the programmable logic (PL). The moving target architecture proposed in this work leverages DPR to implement a power analysis countermeasure to side-channel attacks, the most common of which are referred to as differential power analysis (DPA) and correlation power analysis …

Computational_Electromagnetic Modeling (Cem) Of Foliage Penetration (Fopen), Monica R. Jaramillo

Electrical and Computer Engineering ETDs

Foliage penetration (FOPEN) radar at lower frequencies (UHF, VHF) is a well-studied area with a wide set of contributions. However, there is growing interest in using higher Ku-band frequencies (12-18 GHz frequency range) for FOPEN. In particular, the reduced wavelength sizes (centimeters range) provide some key saliencies for developing more optimized foliage detection solutions. The disadvantage is that exploiting Ku-band for FOPEN is complicated because higher frequencies have much more pronounced scattering effects due to their smaller wavelengths. Despite these challenges, certain foliage characteristics and signal parameters can help improve electromagnetic (EM) wave penetration in the Ku-band such as foliage …

Guest Editorial: Edge Intelligence For Beyond 5g Networks, Yan Zhang, Zhiyong Feng, Hassnaa Moustafa, Feng Ye, Usman Javaid, Chunfen Cui

Electrical and Computer Engineering Faculty Publications

Beyond fifth-generation (B5G) networks, or so-called "6G", is the next-generation wireless communications systems that will radically change how Society evolves. Edge intelligence is emerging as a new concept and has extremely high potential in addressing the new challenges in B5G networks by providing mobile edge computing and edge caching capabilities together with Artificial Intelligence (AI) to the proximity of end users. In edge intelligence empowered B5G networks, edge resources are managed by AI systems for offering powerful computational processing and massive data acquisition locally at edge networks. AI helps to obtain efficient resource scheduling strategies in a complex environment with …

Three-Dimensional (3d) Memory I/O Interface Design Using Quad-Band Interconnect (Qbi) And Eight-Level Pulse Amplitude Modulation (8-Pam), Xiaoyan Wang

Electrical Engineering Theses and Dissertations

The demand for high bandwidth, low latency, reconfigurable, and small form factor memory I/O interface design has significantly increased with the development of data-intensive applications, such as artificial neural networks and high-performance computing. However, the current memory I/O interface technologies have critical limitations, such as limited bandwidth, limited pin count, long latency, non-reconfigurable data access, and large form factor. Therefore, a novel memory I/O interface design is needed to overcome these limitations.

This dissertation presents two novel memory I/O interface designs using 3D integration, QBI, and 8-PAM technologies to improve bandwidth, latency, reconfigurability, and form factor for future mobile devices. …

Experimental Study Of Hollow-Core Slab Containing Waste Pet Bottles, Mulia Orientilize, Josia Irwan Rastandi, R. M. Dimas Aries C., Marsha Niken P., Krisna Adi S.S., Abimantrana Abimantrana

Makara Journal of Technology

This study investigated the utilization of plastic-waste concrete as an effort to reduce urban waste problems. The waste plastic bottles were utilized to form the hollows of the hollow-core slabs (HCSs). The bottles were made of polyethylene terephthalate (PET). As a part of green research to reuse waste material, shredded PET was also added to the concrete mixture to improve the HCS strength. The cast-in-site HCS could be constructed without any difficulties. Three parameters were investigated: the effects of void content, shredded PET content, and steel-fiber (SF) content on the HCS ultimate bending capacity (Mu). Fifteen specimens were tested under …