Electrical and Electronics Commons^™

Reflection Coefficients Of P- And S-Polarized Light By A Quarter-Wave Layer: Explicit Expressions And Application To Beam Splitters, R. M.A. Azzam, F. F. Sudradjat

Electrical Engineering Faculty Publications

The complex-amplitude reflection coefficients of p- and s-polarized light by a transparent freestanding, embedded, or deposited quarter-wave layer (QWL) are derived as explicit functions of the angle of incidence and layer refractive index. This provides the basis for the design of 50%-50% beam splitters for incident s-polarized or unpolarized light that use a high-index (e.g., TiO₂ or Ge) QWL embedded in a glass cube in the visible and near infrared spectral range. These simple devices have good angular and spectral response and are insensitive to small film thickness errors to the first order.

Efficiency Of Linear-To-Circular Polarization Conversion For Light Reflection At The Principal Angle By A Dielectric-Conductor Interface, R. M.A. Azzam, A. Alsamman

Electrical Engineering Faculty Publications

The efficiency ηLC of linear-to-circular polarization conversion when light is reflected at a dielectric–conductor interface is determined as a function of the principal angle ϕ¯ and principal azimuth ψ¯ . Constant- ηLC contours are presented in the ϕ¯ ,ψ¯ plane for values of ηLC from 0.5 to 1.0 in steps of 0.05, and the corresponding contours in the complex plane of the relative dielectric function ϵ are also determined. As specific examples, efficiencies ⩾88% are obtained for light reflection by a Ag mirror in the visible and near-IR (400–1200nm) spectral range, and ≥40% for the reflection of extreme ultraviolet (EUV) …

Increasing Combat Aircraft Survivability Through Coherent Self-Protection Jammers, Soner Ozer

Theses and Dissertations

When the battlefields were within the visual range, the objective of deception tactics in warfare was to deceive the human senses. In the battlefield of electromagnetic spectrum, the objective of deception is to deceive the sensors of the enemy weapon systems. The survivability of the aircraft operating in hostile environment is of prime importance to the mission planner. If the aircraft can deny its location information to the tracking radar of the radar guided threat missile system, this, in return, may increase its survivability. The deception, a tactic which stems from the wisdom of ancient battles, incarnated in the form …

Anti-Tamper Method For Field Programmable Gate Arrays Through Dynamic Reconfiguration And Decoy Circuits, Samuel J. Stone

Theses and Dissertations

As Field Programmable Gate Arrays (FPGAs) become more widely used, security concerns have been raised regarding FPGA use for cryptographic, sensitive, or proprietary data. Storing or implementing proprietary code and designs on FPGAs could result in the compromise of sensitive information if the FPGA device was physically relinquished or remotely accessible to adversaries seeking to obtain the information. Although multiple defensive measures have been implemented (and overcome), the possibility exists to create a secure design through the implementation of polymorphic Dynamically Reconfigurable FPGA (DRFPGA) circuits. Using polymorphic DRFPGAs removes the static attributes from their design; thus, substantially increasing the difficulty …

Improvement Of Ecm Techniques Through Implementation Of A Genetic Algorithm, James D. Townsend

Theses and Dissertations

This research effective effort develops the necessary interfaces between the radar signal processing components and an optimization routine, such as genetic algorithms, to develop Electronic Countermeasure (ECM) waveforms under a Hardware-in-the-Loop (HILS) architecture. The various ECM waveforms are stored in an ECM library, where an operator selects the desired function to use against a particular system. This optimization works with modular components, compared to previous research that embedded a genetic algorithm into the Range Gate Pull-off (RGPO) waveform optimization loop, which can be interchanged based upon the operator's desired hardware/ software testing setup. The ECM library's first entries contain the …

Tailoring Metallodielectric Structures For Superresolution And Superguiding Applications In The Visible And Near-Ir Ranges, Domenico De Ceglia, Maria Antonietta Vincenti, M. G. Cappeddu, Marco Centini, Neset Akozbek, Antonella D'Orazio, Joseph W. Haus, Mark J. Bloemer, Michael Scalora

Electrical and Computer Engineering Faculty Publications

We discuss propagation effects in realistic, transparent, metallodielectric photonic band gap structures in the context of negative refraction and super-resolution in the visible and near infrared ranges. In the resonance tunneling regime, we find that for transverse-magnetic incident polarization, field localization effects contribute to a waveguiding phenomenon that makes it possible for the light to remain confined within a small fraction of a wavelength, without any transverse boundaries, due to the suppression of diffraction. This effect is related to negative refraction of the Poynting vector inside each metal layer, balanced by normal refraction inside the adjacent dielectric layer: The degree …

Digital Fingerprinting Of Field Programmable Gate Arrays, James W. Crouch

Theses and Dissertations

Commercial off-the-shelf (COTS) component usage is becoming more prevalent in military applications due to current Department of Defense (DoD) policies. The easy accessibility of COTS will give reverse engineers a higher probability of successfully tampering, coping, or reverse engineering circuits that contain critical capabilities. To prevent this and verify the trustworthiness of hardware, circuit identification tags or serials numbers can be used. However, these values can be easily obtained and forged. To protect critical DoD technologies from possible exploitation, there is an urgent need for a reliable method to confirm a circuit’s identity using a set of unique unforgettable metrics. …

Design And Optimization Of Broadband High Impedance Ground Planes (Higp) For Surface Mount Antennas, Murat Dogrul

Theses and Dissertations

Gain and bandwidth metrics of broad-band low-profile antennas severely deteriorate when they are placed conformally onto the conductive skins of air, sea, and ground platforms. This detrimental effect is primarily due to out-of-phase reflections from the conductive body interfering with the antenna’s self radiation. Furthermore, lateral waves launched by the antenna couple into the thin substrate placed between the antenna and the platform, giving rise to surface waves resulting in significant diffraction from the edges of the substrate. To remedy these two major mechanisms degrading antenna performance, high impedance ground planes (HIGP) were designed. HIGPs made of a 2-dimensional periodic …

Characterization And Implementation Of A Real-World Target Tracking Algorithm On Field Programmable Gate Arrays With Kalman Filter Test Case, Benjamin D. Hancey

Theses and Dissertations

A one dimensional Kalman Filter algorithm provided in Matlab is used as the basis for a Very High Speed Integrated Circuit Hardware Description Language (VHDL) model. The JAVA programming language is used to create the VHDL code that describes the Kalman filter in hardware which allows for maximum flexibility. A one-dimensional behavioral model of the Kalman Filter is described, as well as a one-dimensional and synthesizable register transfer level (RTL) model with optimizations for speed, area, and power. These optimizations are achieved by a focus on parallelization as well as careful Kalman filter sub-module algorithm selection. Newton-Raphson reciprocal is the …

Electrically Steerable Diffraction Gratings For Hyperspectral Imaging: A Microelectromechanical System Design And Fabrication, Saban Atinc Delican

Theses and Dissertations

The current research is focused on the design and fabrication of an electrically programmable diffraction grating using standard micro electro mechanical systems (MEMS) technology. The goal is to design a beam steering element required to build very small hyperspectral imaging (HSI) sensors. The diffraction grating will be used to perform beam-dispersion - a critical step in the imaging process. The proposed transmissive diffraction grating based approach will minimize the overall size and the number of components in the physical design of the hyperspectral imagers, thereby enabling us to exploit the traditional advantages of MEMS such as increased reliability, smaller size, …

Design And Analysis Of Scalable Scheduling Schemes For High-Speed Input-Queued Packet Switches, Chuan-Bi Lin

Dissertations

Single-stage input-queued (IQ) switches are attractive for implementation of high performance routers because they require no speedup in the used memory. It has been shown that IQ switches can provide 100% throughput under admissible traffic when using either maximum-weight matching schemes or iterative maximal-weight matching schemes with a significant speedup. These different approaches require either high computation complexity or high memory costs that can make them infeasible. Therefore, there is a need for low-complexity and fast matching schemes that provide high throughput under several admissible traffic patterns, without recurring to speedup nor multiple iterations. In this thesis. the concept of …

Architecture Design And Performance Analysis Of Practical Buffered-Crossbar Packet Switches, Ziqian Dong

Dissertations

Combined input crosspoint buffered (CICB) packet switches were introduced to relax inputoutput arbitration timing and provide high throughput under admissible traffic. However, the amount of memory required in the crossbar of an N x N switch is N²x k x L, where k is the crosspoint buffer size and needs to be of size RTT in cells, L is the packet size. RTT is the round-trip time which is defined by the distance between line cards and switch fabric. When the switch size is large or RTT is not negligible, the memory amount required makes the implementation …

Propagation And Scattering Of Beam Waves In Vegetation Using Scalar Transport Theory, Michael Yu-Chi Wu

Dissertations

Vegetation is a very complex propagation medium, and multiple scattering effects play a significant role in the propagation of microwave and millimeter (mm)-wave signals through foliage. At frequencies above 1 GHz,both the coherent and incoherent field components have to be taken into account and vegetation has to be modeled as a random medium of discrete scatterers having a wide variety of sizes and shapes. Multiscattering can be studied effectively by using transport theory. In prior studies, theories have been developed for microwave and mm-wave propagation in vegetation using transport theory for continuous wave and pulsed signals. In this study, the …

Polarization Properties Of Retroreflecting Right-Angle Prisms, R. M.A. Azzam, H. K. Khanfar

Electrical Engineering Faculty Publications

The cumulative retardance Δ_t introduced between the p and the s orthogonal linear polarizations after two successive total internal reflections (TIRs) inside a right-angle prism at complementary angles Φ and 90°−Φ is calculated as a function of Φ and prism refractive index n. Quarter-wave retardation (QWR) is obtained on retroreflection with minimum angular sensitivity when n=(√2+1)^1/2=1.55377 and Φ=45°. A QWR prism made of N-BAK4 Schott glass (n=1.55377 at λ=1303.5 nm) has good spectral response (<5° retardance error) over the 0.5-2 μm visible and near-IR spectral range. A ZnS-coated right-angle Si prism achieves QWR with an error of <±2.5° in the 9-11 μm (CO₂ laser) IR spectral range. This device functions as a linear-to-circular polarization transformer and can be tuned to exact QWR at any …

Throughput Enhancement Through Combined Fragmentation And Rate Method In Ieee 802.11b Wlans, Marek Bykowski, Karol Kowalik, Brian Keegan, Mark Davis

Conference papers

IEEE 802.11 allows for fragmentation tuning and rate selection. Their combined usage is referred sometimes to link adaptation. However, the algorithms of link adaptation are beyond the 802.11 standards. In this paper we investigate the benefits arising from proper use of link adaptation. Particularly, we develop a mathematical model describing the fragmented transmission in 802.11b. We examine potential benefits of it over AWGN and fading channels. More significantly we combine fragmentation tuning with bit-rate selection to yield the highest achievable throughput performance for any given channel conditions. Finally, we propose an algorithm that performs the optimal link adaptation.

Color Filter Array Image Analysis For Joint Denoising And Demosaicking, Keigo Hirakawa

Electrical and Computer Engineering Faculty Publications

Noise is among the worst artifacts that affect the perceptual quality of the output from a digital camera. While cost-effective and popular, single-sensor solutions to camera architectures are not adept at noise suppression. In this scheme, data are typically obtained via a spatial subsampling procedure implemented as a color filter array (CFA), a physical construction whereby each pixel location measures the intensity of the light corresponding to only a single color. Aside from undersampling, observations made under noisy conditions typically deteriorate the estimates of the full-color image in the reconstruction process commonly referred to as demosaicking or CFA interpolation in …

Design Of Polynomial-Based Filters For Continuously Variable Sample Rate Conversion With Applications In Synthetic Instrumentati, Matthew Hunter

Electronic Theses and Dissertations

In this work, the design and application of Polynomial-Based Filters (PBF) for continuously variable Sample Rate Conversion (SRC) is studied. The major contributions of this work are summarized as follows. First, an explicit formula for the Fourier Transform of both a symmetrical and nonsymmetrical PBF impulse response with variable basis function coefficients is derived. In the literature only one explicit formula is given, and that for a symmetrical even length filter with fixed basis function coefficients. The frequency domain optimization of PBFs via linear programming has been proposed in the literature, however, the algorithm was not detailed nor were explicit …

Ultra-Wide Band In Communications: Performance Analysis And Enhancements, Burak Berksoy

Electronic Theses and Dissertations

Over the last ten years, Ultra-Wide Band (UWB) technology has attracted tremendous research attention. Frequency allocation of 3.1-10.6 GHz for UWB application by FCC made it apparent that UWB will be the technology for future wireless high speed communication applications. With the promise of high data rates (high channel capacity), UWB also offers advantages such as communication security, high multi-path resolution, good penetration capability, ability to coexist with other communication schemes in the same band, and finally, circuit simplicity. The theoretical advantages of UWB has made it a great candidate for short distance communications, however, UWB communications have many challenges, …

Reducing Eddy Currents In High Magnetic Field Environments, Russell Case

Electronic Theses and Dissertations

When an electrical conducting volume is placed into the bore of an MRI undergoing an image scan, time varying magnetic gradients induce eddy currents in this conducting material. These eddy currents in turn produce a mechanical torque on this volume. It is the goal of this thesis to produce a computer simulation of eddy currents produced by placing conducting materials inside an MRI bore. The first part of the thesis establishes the physics and principles behind an MRI system along with several applications. Next, this thesis presents an analysis of eddy current effects produced on a conductor placed into an …

Bi-Directional Dcm Dc-To-Dc Converter For Hybrid Electric Vehicles, Michael Pepper

Electronic Theses and Dissertations

With the recent revival of the hybrid vehicle much advancement in power management has been made. The most popular hybrid vehicle, the hybrid electric vehicle, has many topologies developed to realize this hybrid vehicle. From these topologies, as sub set was created to define a particular group of vehicles where the converter discussed in this thesis has the most advantage. This sub set is defined by two electric sources of power coupled together at a common bus. This set up presents many unique operating conditions which can be handled seamlessly by the DC-to-DC converter when designed properly. The DC-to-DC converter …

Homography Based Multiple Camera Detection Of Camouflaged Targets, Jesus Flores Guerra

Open Access Theses & Dissertations

This Thesis proposes an improvement on segmentation of camouflaged objects by combining information from multiple static cameras with overlapping views onto a common reference plane. Previous camouflage detection work relies on a single camera and focuses on pattern recognition, gray level co-occurrence matrix (GLCM) computation, convexity detection and operations such as connected components or morphology. These methods make real-time implementation computationally expensive. The proposed work diverges from these techniques, taking advantage of the added information from several viewpoints. Background subtraction is performed on each individual camera and then, the segmentation result is transformed onto a common plane using homography. A …

Zinc Telluride Deposition Using Close Space Sublimation, Luis Carlos Romo

Open Access Theses & Dissertations

This thesis presents the optimization process of the close space sublimation (CSS) technique to deposit zinc telluride (ZnTe) on thin-film cadmium telluride (CdTe) solar cells. Previous research has demonstrated that creating a heavily doped ZnTe intermediate layer between the absorber-CdTe and the back contacts produces low-resistive CdTe contacts that overcome the Schottky barrier created at the interface of a metal and a semiconductor [11]. ZnTe interlayer forms a tunnel barrier at the contact interface so the positive charges created at the p-CdTe/n-cadmium sulfide (CdS) junction can be easily collected at the back contact maximizing the current collection process. However, ZnTe …

Stochastic Gaussian And Non-Gaussian Signal Modeling, Madhu Kishore Yerramothu

Open Access Theses & Dissertations

This thesis introduces a methodology for modeling stochastic signals that have either Gaussian or approximately bell-shaped non-Gaussian distribution. The synthesized model can be used to generate stochastic signals that approximate both the power spectral density (PSD) and the probability density function (pdf) of the original stochastic signal. The new methodology is based on non-linear transformations, filter banks and autoregressive-moving average (ARMA) models. Because the stochastic signals modeled can have Gaussian distribution or approximately bell shaped non-Gaussian distribution, normality tests such as sample skewness, sample kurtosis, Kolmogorov-Smirnov test, and Shapiro-Wilk test are also used.

Many methods have been proposed in the …

Modeling And Analysis Of Power Mosfets For High Frequency Dc-Dc Converters, Yali Xiong

Electronic Theses and Dissertations

Evolutions in integrated circuit technology require the use of a high-frequency synchronous buck converter in order to achieve low cost, low profile, fast transient response and high power density. However, high frequency operation leads to increased power MOSFET switching losses. Optimization of the MOSFETs plays an important role in improving converter performance. This dissertation focuses on revealing the power loss mechanism of power MOSFETs and the relationship between power MOSFET structure and its power loss. The analytical device model, combined with circuit modeling, cannot reveal the relationship between device structure and its power loss due to the highly non-linear characteristics …

Transient Response Improvement For Multi-Phase Voltage Regulators, Shangyang Xiao

Electronic Theses and Dissertations

Next generation microprocessor (Vcore) requirements for high current slew rates and fast transient response together with low output voltage have posed great challenges on voltage regulator (VR) design . Since the debut of Intel 80X86 series, CPUs have greatly improved in performance with a dramatic increase on power consumption. According to the latest Intel VR11 design guidelines , the operational current may ramp up to 140A with typical voltages in the 1.1V to 1.4V range, while the slew rate of the transient current can be as high as 1.9A/ns [1, 2]. Meanwhile, the transient-response requirements are becoming stringer and stringer. …

Design, Characterization And Compact Modeling Of Novel Silicon Controlled Rectifier (Scr)-Based Devices For Electrostatic Discha, Lifang Lou

Electronic Theses and Dissertations

Electrostatic Discharge (ESD), an event of a sudden transfer of electrons between two bodies at different potentials, happens commonly throughout nature. When such even occurs on integrated circuits (ICs), ICs will be damaged and failures result. As the evolution of semiconductor technologies, increasing usage of automated equipments and the emerging of more and more complex circuit applications, ICs are more sensitive to ESD strikes. Main ESD events occurring in semiconductor industry have been standardized as human body model (HBM), machine model (MM), charged device model (CDM) and international electrotechnical commission model (IEC) for control, monitor and test. In additional to …

Management Framework For Hybrid Wireless Networks, Chong Shen

Theses

The objective of the Hybrid Wireless Network with dedicated Relay Nodes (HWN*) architecture is to interface the Base Station (BS) Oriented Mobile Network (BSON) and the 802.fix based Mobile Ad hoc Wireless Network (MANET) so that one system can be utilised as an alternative radio access network for data transmissions, while the incorporation of Relay Nodes (RN) is to extend the communication coverage, optimise medium resource sharing, increase spatial reuse opportunity, stabilise MANET link and create more micro-cells. The HWN* keeps the existing cellular infrastructure and a Mobile Terminal (MT) can borrow radio resources from other cells via secure multi-hop …

Container Management And Monitoring Using Sensor Networks, Daniel Rogóz

Theses

The purpose of this project was to develop a functional prototype of a container management and monitoring system, which allows identification and tracking of shipping containers in a port terminal from the moment they enter a port to when they depart for their final destination.

Such system can significantly reduce the labor and time costs associated with organizational mistakes that can occur when containers are being on/off-loaded, moved and stacked in tiers for transfer to the rail or road network. It can be used to streamline the container transport, optimize the order of container on/off-loading and placement, as well as …

Acceptor Levels In Gase:In Crystals Investigated By Deep-Level Transient Spectroscopy And Photoluminescence, Y. Cui, R. Dupere, A. Burger, D. Johnstone, K. C. Mandal, S. A. Payne

Faculty Publications

No abstract provided.

High Temperature Packaging For Wide Bandgap Semiconductor Devices, Brian Grummel

Electronic Theses and Dissertations

Currently, wide bandgap semiconductor devices feature increased efficiency, higher current handling capabilities, and higher reverse blocking voltages than silicon devices while recent fabrication advances have them drawing near to the marketplace. However these new semiconductors are in need of new packaging that will allow for their application in several important uses including hybrid electrical vehicles, new and existing energy sources, and increased efficiency in multiple new and existing technologies. Also, current power module designs for silicon devices are rife with problems that must be enhanced to improve reliability. This thesis introduces new packaging that is thermally resilient and has reduced …