Electrical and Electronics Commons^™

Uniformity Corrector And Signal Processing For A 160 X 244-Element Ir-Ccd Camera With Ptsi Schottky-Barrier Detectors, Paul D. Blume

Theses

An off-set-type, one point response uniformity corrector and the associated signal processing circuits was developed to be used for a 160 x 244-element IR-CCD camera with PtSi Schottky-barrier detectors. Image sensors with PtSi Schottky-barrier detectors exhibit two types of noise in the displayed video output, a temporal noise and a spatial fixed pattern noise. The performance of the image sensor, limited by the spatial noise which obscures low contrast detail and limits camera sensitivity, can be improved by a uniformity corrector. The uniformity corrector was constructed to substantially reduce the spatial noise in the output display by digitally subtracting a …

Infrared Tv Camera With Ptsi Schottky-Barrier Detectors, Steven J. Blume

Theses

An infrared TV camera was developed for operating various sizes of Schottky-barrier IR-CCD image sensor chips. A digitally programmable frequency synthesizer is used so that the camera has the flexibility of using a 160 x 244 or 320 x 244 image sensor developed at the David Sarnoff Research Center. The outputs of the camera are compatible with an XYZ monitor, a standard TV monitor, and a computer workstation. Operation of the camera was demonstrated with a 160 x 244 image sensor producing an output on a standard TV monitor. Performance of the IR-TV camera system was investigated by evaluating CCD …

Performance Analysis Of A Dynamic Reservation Multichannel Local Area Network, Abubakar A. Ibrahim

Theses

A reservation multiaccess protocol. is proposed to be used on multichannel local area networks. This protocol is advantageous for networks supporting integrated services. The delay and throughput performance for message transmission are obtained by analysist The delay performance of the protocol is similar to the M-CSMA/CD/IC multichannel network proposed by Marsan and Roffinella. It is found that the reservation protocol can provide better throughput-delay characteristics when the fraction of the total available bandwidth allocated to data is increased. It is also observed that the maximum throughput increases with the increase in the number of channels when the total bandwidth is …

Formation And Characterization Of Thin Superconducting Y-Ba-Cu-O Films, Gyusuk Kim

Theses

Thin Y-Ba-Cu-O superconducting films were fabricated reproducibly on MgO (100) substrates by two different processes ; (1) deposition at a low substrate temperature fiom a single sintered YBa₂Cu_3.3O_x target using RF diode reactive sputtering followed by a post-annealing at around 830 ° C ; (2) deposition at the crystallization temperature under oxidizing atmosphere. The superconducting properties of films deposited by process (1) and (2) were studied. The variation of film composition and thickness as a function of distance from the target gas pressure and distance between target and substrate was studied. The Dependence of the …

The Magnetotransport Analysis Of Hemt Structures At Low Fields, Naghmeh Nouri

Theses

On the basis of a study on numerous HEMT structures, a simple and useful technique was established for the characterization of 2DEG layers. This technique utilizes the magnetic field-dependence of the resistivity and Hall coefficient of the HEMT structure, to determine the values of the sheet density and mobility of 2DEG in the presence of other parallel conductive layers. This method of analysis was compared with previously used techniques such as Shubnikov-de Haas and the etch removal of the parallel conductive layers. Through this comparison and several measurements it was found that this procedure gives reproducible values for the 2DEG …

Sputter Deposition And Characterization Of High Tc Superconducting Thin Films, Vipulkumar Patel

Theses

Preparation of thin superconducting films by direct RF sputter deposition on Si, MgO, SrTiO₃ and quartz substrates and silver and Sl3N4 buffer layers (deposited on silicon substrates) was studied. To study resistance versus temperature characteristics of thin films and bulk materials, a computerized measurement system was developed. 1-1.5 pm thick YBaCuO films deposited on Si₃N₄/Si were found to be insulating with room temperature resistance higher than 236KΩ, while films with Ag as a buffer and/or a passivating layer exhibited metallic behavior with room temperature resistances lower than 700mΩ. The area directly under the 2.25 inches …

The Design Of Decentralized Optimal Regulator Systems Using Matrix Minimum Principle, Sunny Lai Yick

Theses

This research considers the design of linear, time-varying regulator systems using Matrix Minimum Principle in the frame work of decentralized control theory. The regulator system is modeled in terms of state equation with multiple controllers. Each controller works cooperatively to optimize a common quadratic performance index. An additional constraint is imposed such that the controllers are linear time-varying functions of the outputs.

Necessary and sufficient conditions for optimality of the system are provided by the Matrix Minimum Principle and Hamilton-Jacobi Theory.

Two examples are developed to illustrate the concept.

Simulation And Design Of Field Emission Diode, Yun Yuan

Theses

A new generation of microelectronic devices utilizing vacuum field emission cathodes becomes surging interest in recent years. This paper concentrates on the study of the field emission diode — a basic vacuum microelectronic device. The field emission efficiency, current spatial distribution and time dispersion of conical tips and wedges of various geometrical shapes are compared and calculated by analytical methods and computer simulations. Two field emitter heating effects, namely the Joule heating and Nottingham effect, are discussed theoretically. All the simulation results in this paper are performed on 386 based personal computer. The limiting memory space of PC induced simulation …

Fault Tolerant Benes Networks, Manoj Bhatnagar

Theses

A fairly large number of fault tolerant topologies have been proposed for the multistage interconnection networks in the recent years. However very few of these schemes have focused on the Benes network. This thesis presents two new fault tolerant architectures for the Benes network. The thesis includes algorithms to construct these fault tolerant networks from a Benes network and the reconfiguration procedure in the event of a fault. The hardware characteristics of both the fault tolerant networks have been analyzed and compared.

Evaluation Of Sorting Algorithm Performance On Single Instruction Multiple Data Machines, Dong Kuen Yang

Theses

Partitioning an application program into several tasks and executing them via parallel processing is one way to increase computation throughput and performance. But with a uniprocessor system, the performance increase will be minimal. Computer scientists have developed several multiprocessor systems to gain more speed in computation.

There are several computer architectures, such as pipeline machines, array processors and multiprocessor systems. They provide a parallel execution environment to increase the execution speed. But as the system becomes more complex, the communication traffic density between several processors increases more heavily. It has to provide some kind of control algorithm or routing function …

Reliability Prediction Of Vulcanized Fibre Using Electrical Noise As A Screening Parameter, George A. Donos

Theses

The main objective of this thesis was to find a correlation between the electrical noise generated within the body of Vulcanized Fibre in insulating service and the time of its breakdown under a synergy of electrical, thermal and mechanical stresses. Failure was defined as a material discontinuity, puncture, under accelerated life test conditions. Radio frequency measurements of the partial discharges occuring in the voids of the material were performed on 1240 samples of vulcanized fibre with 10 mil thickness. The level of electrical noise measured was used to classify the specimens into the three following categories: (a) Low Noise:0-2.8μV (0-9db), …

Manufacturing Workstation Model Using Petri Nets, Reni Alexander

Theses

Petri nets have become a powerful tool for modeling and analyzing asynchronous concurrent systems. In this thesis I apply Petri nets for analyzing and modeling a flexible manufacturing workstation (FMS). A manufacturing workstation is modeled by using Colored- Timed Petri nets, with the consideration of tool handling, raw materials, quality checking and the reuse of reworkable scraps. A simulation program for a simplified Petri net model of manufacturing workstation is described and the production throughput is computed.

Adaptive Transform Coding Of Video With Motion Compensation And Vector Quantization, Jung-Hui Chien

Theses

This thesis proposes an efficient transform coding scheme for the low bit rate video sequence. The redundancy within adjacent video frame is exploited by motion compensated interframe prediction using the efficient independent orthogonal search technique, and the motion compensated frame difference (MCFD) signal is transform coding by 1-D DCT, 1-D HDCT and 2-D DCT, the coefficients are zonal masked, and vector quantizatied adaptively. The encoded MCFD as well as the motion information and variance grouping (side informations) are transmitted to the receiver to reconstruct the frame. The transform MCFD signal is classified into the four groups according to the coefficient …

Robotic Arms With Flexible Links As The Links Approach Rigidity, George A. Downes

Theses

The dynamics of single link flexible robotic arms are modeled using the Bernoulli-Euler beam equation and Lagrange's equation. The Bernoulli-Euler beam equation derivation is reviewed and is studied in the limiting case as the flexiblity approaches zero. Using the Bernoulli-Euler beam equation, a procedure is developed to calculate the position of the endpoint of a link given the displacement, slope or curvature of any point on the link. Also a procedure is developed to calculate the minimum Young's modulus of elasticity, E, given a specified endpoint displacement tolerance.

A rigid link model based on Lagrange's equation and a flexible link …

Recursive System Identification Using Least Squares Method, Gholamreza Ghorbani Moghadam

Theses

Input and output sampling, in addition to computer simulations, are now an integral part of system identification. In this thesis, the concept of analyzing any time invariant continuous deterministic system will be developed by identifying a linear discrete - time system equivalent to the continuous one. In this method, two computer programs are written in pascal. The first program applies the Recursive Least Squares Method to discrete - time systems in order to estimate the system components. The second program estimates the future output of the system. Four systems have then identified using the programs.

In this process, system identification …

Design And Analysis Of An Intracranial Pressure And Temperature Sensor Telemetry System, Anshumat Parasar

Theses

This thesis presents a signal conditioning and telemetry system for an implantable pressure and temperature transducer. The initial target application is for measuring the epidural intracranial pressure in the range of 25-100 millitorr and temperature over the range 90 — 110° F. The implant, based on custom silicon IC design can be packaged within a volume of 2cm3 and will require surgical procedures for placement and removal. Effort has been made in this thesis to design the transducer, associated signal conditioning and telemetry circuits for useful operation over a wide range of power supply voltage. The implanted device is powered …

Effects Of N>M Clos Networks On Edge Coloring And Matrix Decomposition Algorithms, Ming-Hsing Lin

Theses

Considered in this thesis are n > m Clos networks on edge coloring and matrix decomposition algorithms. This work uses a two-fold approach to examine the effects of n > m Clos networks on edge coloring and matrix decomposition algorithms. First, edge coloring and matching on bipartite multigraphs are applied to routing on Clos networks. It is demonstrated that edge coloring algorithms which find a minimum edge coloring set up the routing for n > m Clos networks with redundancy. The results presented here indicate that the Euler coloring algorithm has applications on n > m Clos networks because it has fast time complexity …

Protocol Processing Delay Analysis On Ethernet By Simulation Of Njit Ethernet, Jagdish Gangrimal Rangwani

Theses

CSMA/CD based Local Area Networks account for about 75% of the installed LAN base today. As these networks are becoming available for high channel bandwidth, it is important to identify the bottlenecks in these networks. As channels are becoming high speed, bottleneck is shifting from channel to protocol processing. This delay depends on a particular implementation of the protocol and not the protocol standard itself.

This Thesis presents the analysis of delay on Ethernet. To achieve realistic results NJIT Ethernet, as it is configured, is modelled and simulated. Traffic on this network is measured and load on each segment is …

Semiconductor Pressure Sensor And Amplifier With Extended Temperature Range, Abhay Mahadeo Joshi

Theses

In this thesis work, a unique raicrosensor was designed for pressure measurements over the temperature range of -80 C to 125 C. The sensor has CMOS circuitry powered by a single voltage supply. It can be used for military and space applications including monitoring the pressure acting on the nose of the space shuttle.

The sensor consists of a thin silicon diaphragm, which is stressed by external pressure. Four resistors in a Wheatstone bridge configuration are diffused into the diaphragm. The temperature drift in the silicon sensors is dominated by the temperature dependence of the piezoresistive coefficients. The resistors are …

A Cad For Edif Pattern Generation, Mohammad Akram Khan

Theses

Generating a set of test vector for a digital circuit is the most critical step in design and test. It is very important to generate test sequence easily and efficiently. The importance is enhanced by the fact that the simulation database is being used to create test programs. A CAD tool ATPG (Automatic Test Pattern Generator) has been developed to specify and satisfy requirements of designers and test engineers. EDIF (Electronic Design Interchange Format) is followed closely. EDIF targets compatability among foundry services and CAD/CAE systems.

Optimization Of Throughput And Stability For Csma/Cd Channel, Liangshyng Jou

Theses

Multiple access technologies plays an important role in designing distributed computer communication system. Here, CSMA/CD has attracted researchers' attentions in the last ten years. In this paper, based on attributions of the slotted, nonpersistent CSMA/CD system, performance of CSMA/CD channel is analyzed. Adaptive Retransmission Technique is adopted to obtain the maximum throughput. Also, equilibrium contours are derived to discuss the stability of the system. And use FET to measure the stability of CSMA/CD channel that FET gives an approximate measure of the average uptime of an unstable channel.

Optimal Algorithmic Testing Of Re-Programmable Logic Arrays, Arvind Chopra

Theses

This research delineates a test strategy and detailed sequence of test vectors for a new class of programmable logic devices (PLDs). This new class of devices is based on architectures that contain programmable logic arrays (PLAs) programmed by on chip integrated static RAMs or EEPROMS. The new PLD architecture poses unique testing problems which require 100% nodal test coverage. Previous PLAs/PLDs did not require that 100% of the nodes be tested since their circuits utilized fuse link crosspoints and were not dynamically reprogrammable. Such devices could be tested by a unique personality pattern that combined the application and the test …

Design Of Robotic Lan Controller And Map Interface, Jayesh M. Joshi

Theses

An application specific integrated circuit has been designed for use as a gateway between two local area networks. This silicon chip provides the gateway function to link the NJIT robotics network and the MAP IEEE-standardized network. This IC utilizes the available Motorola MC 68824 Token Bus Controller for the MAP data path. A special IO design compatible with an optical communication link is used to interface into the NJIT RLAN network.

The gateway IC serves as an asynchronous buffer between the 5Mbps MAP link and the 500 bps local optical link. The control protocol provides the master function for polling …

Analysis On Dielectric Resonators, Xuan Tu

Theses

This dissertation deals with the studies and analysis of Dielectric Resonators (DR). A shielded dielectric iesonator structure, consisting of the substrate, the spacer, the dielectric resonator and the metallic shielding is modelled theoretically. The theoretical expressions for the resonance fields are derived by using radial-mode matching and axial mode-matching techniques. In these techniques, the structure is divided into partial regions and the fields in each pai tial region are represented in terms of a series of the appropriate modes with unknown coefficients. Matching the adjacent regions yields a system of linear or nonlinear equations — which then are solved. The …

Nonlinear Variants Of The Least Mean Square (Lms) Algorithm, John George Van Saders

Theses

Adaptive systems using the LMS algorithm or its variants usually require bilinear correlation multipliers with high dynamic range and large bandwidth. The class of LMS-type algorithms utilizing zero-memory limiters (on one or both correlation multiplier inputs) to reduce dynamic range are examined. The correlator limiters may be included to simplify the hardware implementation or may arise due to limited dynamic range of the loop components. The application of a theorem due to Price provides a technique for simplifying the analysis, which otherwise might be extremely difficult. The analysis provides closed-form expressions for the mean weight convergence behavior, permitting examination of …

Arithmetic Pipeline Analysis Package Ii, Sai K. Vedantam

Theses

This work describes the implementation of arithmetic pipeline scheduling algorithms, to enhance an existing simulation package. The user need only specify the arithmetic equations to be processed and the required stage configuration. The program automatically performs the tasks of forming the reservation table, building the pipeline and specifying the input/output connectivity for each segment and multiplexer in the pipeline. This package integrates two existing simulation tools and enhances many aspects of the previous programs.

The main application area for such a tool is education. Since it is very easy to use and requires little or no time for one to …

Trellis Coded Partial-Response Channels, Kumari Yalamanchili

Theses

Binary partial-response channels with transfer functions (1+D), (1-D) and (1 — D²) are intersymbol-interference channels which find applications in baseband data communications and magnetic recording systems (tapes, discs, compact discs, etc.). In this thesis we develop a coding technique for improving the reliability of digital transmission over noisy partial-response channels with the above transfer functions. We do so by introducing a new concept, called matched encoding, which arises in the context of trellis coding for channels with memory.

We use inner and outer trellis coding of the partial-response channels. The inner codes called matched inner coset codes, are …

Modelling And Parameter Estimation In Clinical Electrooculography, Shengche Hsu

Theses

The Corneoretinal potential (CRP) was discovered in 1848. Its response to changes in light intensity can provide information relevant in the diagnosis of some retinal degenerative disorders. The indirectly measured CRP is referred to as electro-oculography (EOG). A system for automatic data acquisition and modelling, providing graphic presentation, data processing and file management, has been developed. A linear feedback model is proposed to represent the dynamics of the EOG signal. Model parameters are estimated by the nonlinear least-square method. The effect of measurement time on the reliability of parameter estimation is discussed.

Schottky-Barrier Solar Cells, Surface Patterning For Efficient Light Collection, Constantinos Manolis

Theses

Different geometrical surface configurations are considered here for a Au/n-Si semiconductor Schottky-barrier solar cell to improve their light collection efficiency.

Optical and electrical properties are theoretically analyzed for two given optical wavelengths of 0.9 and 0.5 micrometers respectively.

The configurations considered are: V-shaped, Star- shaped, M-shaped, asymmetric-V-shaped, and asymmetric-M-shaped. They all show a significant improvement in the short-circuit current over a flat cell model, while the open-circuit voltage remains practically unchanged.

Algorithms And Analysis Of Dialogue Time Patterns, Muhammad Saleem Akhtar

Theses

The characteristics of a conversation between two people can be determined not only what they say to each other, but also by the rhythm of their dialogue. Their moods, attitudes and attributes may be conveyed in part by time patterns of the speech. The programs described herein can be useful in exploring the relationship between dialogue time patterns and other psychological aspects of human behavior. The measurements of these time patterns can be quickly, inexpensively, and reliably accomplished by the use of a PC.

The programs described herein are capable of calculating the variabilities, the time durations and frequencies of …