Electrical and Electronics Commons^™

Simulation Study Of Monolithic 8-12 Micron Gaas/Algaas Multiple Quantum Well Infrared Image Sensor, Ye Zhu

Theses

The design of a monolithic 8-12 micron GaAs/AlGaAs multiple quantum well infrared image sensor has been tested by computer simulation using PISCES-IIB and SPICE3B.1 software packages. The device structure is in the form of a monolithic GaAs/AlGaAs multiple quantum well (MQW) photoconductor integrated with a GaAs MESFET readout circuit. The readout MESFET's are located in the top layer of the MQW so that a relatively standard GaAs MESFET design and processing technology can be used. The theoretical feasibility of such a vertically integrated structure and the processing compatibility of GaAs/AlGaAs MQW and GaAs MESFET's were investigated in this work.

Our …

Analysis Of Field Distribution Of A Dielectric Resonator And Its Applications, Manohar R. Kamath

Theses

Dielectric resonators (DR) are suitably shaped objects made of high dielectric constant materials like TiO₂, BaO, ZnO, and accessory ingredients, which can function as electrical resonators covering a very wide frequency range upto 40GHz. The physical dimensions of dielectric resonators are in mm range. High dielectric constant material resonators seem to be ideally suited for microwave applications because of their miniature size, low loss, insensitivity to magnetic dc biasing fields, and ability to concentrate large RF magnetic fields in small volumes. However temperature stabilization of dielectric resonators is an important consideration as the center frequency is a function …

Performance Evaluation Of Extended Token Ring Network Under Message Priorities, Prakash B. Kukadia

Theses

Local Area Networks carrying multiple priority classes of messages have received considerable attention recently. A simulation model of a symmetric, priority based network, consisting of token ring networks interconnected by a bridge is implemented. Messages are divided into two priority classes, namely, high priority classes and low priority classes. Two different approaches are considered for transmission of high priority messages. [1] Each station transmits the same amount of high priority traffic when the token reaches the station, regardless of the time elapsed from previous token arrival. [2] The amount of high priority traffic transmitted by each station may vary at …

Study And Characterization Of Ingaas Photodiode And Photodiode Arrays, Krishna R. Linga

Theses

This thesis describes the InGaAs p-i-n photodiodes, photodiode arrays and their characterization. A work station was also built for the opto-electrical characterization. The main feature of the In,_zGa_iAs photodiodes with x > 0.53 is its response to higher wavelengths than the standard lattice-matched photodiodes. An In_xGa_1-xAs photodiode with x = 0.88 respond to 2.6 μm wavelength. The application of these photodiodes is forlIber optic communications, spectroscopy and instrumentation. A complete characterization and analysis of the In_0.88Ga_0.12As photodiodes is presented. Dark current analysis, which is a critical parameter in photodiodes, …

Adaptive Stack Filtering By Lms And Perceptron Learning, Yu-Chou Huang

Theses

Stack filters are a class of sliding?window nonlinear digital filters that possess the weak superposition property(threshold decomposition) and the ordering property known as the stacking property. They have been demonstrated to be robust in suppressing noise. Two methods are introduced in this thesis to adaptively configure a stack filter. One is by employing the Least Mean Square(LMS) algorithm and the other is based on Perceptron learning.

Experimental results are presented to demonstrate the effectiveness of our methods to noise suppression.

Slotted Aloha Protocol For Packet Transmission Via Satellite Link : Throughput Performance Of Continuous Transmission Packet, Solon Karashialis

Theses

The throughput performance of multi-access schemes for data traffic through a satellite channel is analyzed in this paper. Three general schemes are described: channel reservation schemes, random access schemes, and padket reservation schemes. This thesis considers only the random access schemes. Analysis and comparison between ALOHA and Slotted ALOHA are made, but the main emphasis is on satellite channel throughput. A continuous transmission protocol for Slotted ALOHA is suggested in which each ground earth station repeats the transmission of each packet in a number of random repetition slots. The channel is idle when no ground station (GS) is transmitting on …

An Integrated Circuit X-Ray Sensing Array Based On A Cmos Flip-Flop Cell, Huan-Chung Lee

Theses

A novel X-ray sensor IC has beeli designed which counts individual photons at rates up to 5,000,000 counts per second. A two-dimensional X-ray flip-flop sensor array, consisting of an 30 x 30 matrix of CMOS flip-flop sensors integrated in one chip together with an internal clock generator and access selection circuitry is described. A flip-flop sensing cell contains cross-coupled CMOS devices, one of which is connected to a large-area reverse-biased diode. A large area diode exposed to X-ray flux triggers the flip-flop. By reading out the final stable state of the flip-flop, the absence or presence of an X-ray photon …

Design And Development Of Ccd Camera For Document Scanner Using Optical Fiber Bundle, Aniruddha P. Joshi

Theses

A CCD camera for the gray scale document line scanner has been designed and developed at Photon Imaging Corp. The scanner consists of a revolutionary optical fiber bundle, CCD camera, and control electronics. The key concept resides in the fiber-optic bundle. At one end it has a linear array of equally spaced light guides. These terminate at the opposite end in a square array with a polished surface for viewing by a camera. The fan-out from linear to square end is not done with attention to ordering, so the bundle may be relatively inexpensive. Reordering is done electronically using an …

Electromagnetic Transients Program Interfacing, Enhancement And Comparison With Spice, Siswa Trihadi

Theses

The Electromagnetic Transients Program (EMTP) is a computer program used to simulate high speed power system transients. The EMTP input data structures and the rules in setting up the input data file are described in this thesis by means of two sample cases i.e an RLC series circuit and a sin le line to ground fault in power system.

The EMTP input data are very detailed an highly-structured column-dependent. To improve the user-friendliness of EMTP by ignoring the difficulty of arranging the column structures, this thesis presents the EM P User Interactive Program. Sample cases using this interactive program are …

A 512 X 512 Random Addressable Variable Resolution Image Sensor, Chakravarthy Yarlagadda

Theses

This thesis presents the design and layout of a 512 x 512-element with 20μm x 20μm pixels image sensor that emulates the properties of the human eye and is useful in high speed processing of visual data for machine vision applications. The imager will be able to operate with random-address selection in variable resolution or with multiple regions of interest to reduce the number of pixels readout. The selection of the pixels is done by x-y addressing the MOS switches which connect the photodiode pixel to the output through the sense lines. The design of column decoder and row decoder …

Photo-Induced Electrochemical Etching Of Inp Semiconductor In A Thin Film Cell, Bungsu Iskandar

Theses

The Photo-Induced Electrochemical Etching of n-InP wafer in aqueous solution is investigated for both reservoir and capillary systems. A sinusoidal spatial variation of light intensity pattern is directly illuminated and promoting etching on an InP semiconductor wafer. The etching process is time-efficient, and produces highly isotropical and a promising high resolution pattern. It gives a good reproducibility and has less contaminating features. Its features may be explained by a non-linear relationship between the electrolyte concentration and the photo-generated holes density at the interaction surface. An optimal reaction rate is determined by the ratio of the reactivity to ionic diffusion, either …

Rotary Micromotor Design With Ic-Compatible Processing, Hong Yu

Theses

Several microelectromechanical rotary motors have been designed and simulated with varying rotor and stator configurations. All of these micromotors operate with an electrostatic power source and have rotor diameters varying from 0.2 to 0.4 mm. These micromotors develop torques in the range 8 to 50 picoNewtons with rotors of polysilicon with 2 micron film thickness based on the detailed simulations of this thesis using a 3-phase voltage power source. The geometries modelled in this work are side-drive and vertical-drive configurations. These micromotors obtain drive torque from the fringe-field differential at the periphery of the rotor poles.

Unlevitated micromotors (with bearings) …

Implementation Of Parallel Sorting Algorithms On A Transputer Network, Venkatraman U. Calidas

Theses

Many sorting algorithms, such as the bubble sort and the binary tree selection sort, are n-squared algorithms and take O (n2) time to sort n values. These can be easily parallelized; the resulting sorts are called the odd-even transposition sort and the parallel tree selection sort, respectively. These have O(nlogn) time complexity. The quicksort is an O(nlogn) algorithm and it can parallelized to make it an O(logn) algorithm.

A transputer is a microprocessor which has serial links to transmit and receive data from other transputers. The above algorithms are implemented on a network of transputers and the link connections for …

Monolithic Induction-Sourced Ac-To-Dc Power Supply Design, Jianhua Chen

Theses

This thesis describes techniques with design nomographs for supplying power to CMOS and microelectromechanical implanted devices. These applications require voltages in the range of 5 to 50 volts. Different kinds of voltage multiplier circuits were used to achieve high voltage output. The AC-to-DC and DC-to-DC capacitive bootstrap voltage multipliers are designed and analyzed. The AC-to-DC and DC-to-DC inductive bootstrap voltage multiplier circuits are presented and the SPICE simulations are done with those circuits. Four different options of inductive link high voltage power supply are presented, analyzed and compared. The link parameters of two VLSI-compatible square-shaped coils are calculated in both …

Investigation Of Micromechanical Properties Of Tungsten Silicide Thin Films, Bharat Pathak

Theses

Micromechanics is a field which is maturing. Recent research interest in micromechanical structures has focussed on the fabrication of microactuators and microsensors. These microsensors and actuators can sense very small changes in the environment without disturbing the equilibrium of the environment. The refractory silicides are some of the compatible materials used to integrate the micromechanical structures and the interfacing electronic circuits on the same chip. As a result of this, the thermodynamic, electrical and mechanical properties of transition metal silicides should be given a closer look for micromechanical applications.

This thesis details the design and fabrication of tungsten silicide moveable …

Simulation And Analysis Of Priority Classes In Extended Token Based Local Area Networks, Bhavinkumar R. Pathak

Theses

Recently, Local Area Networks carrying multiple priority classes of messages have received considerable attention. The IEEE 802.5 token ring standard defines an optional priority scheme to handle different priority classes of messages. A simulation model of symmetric priority based networks, consisting of token ring networks interconnected by a bridge is considered. Messages are divided into two priority classes, namely, high priority traffic and low priority traffic. High priority traffic is guaranteed access on the channel, whereas low priority messages are served when the system determines that no high priority messages are currently waiting. The simulation results are used to evaluate …

Microcomputer-Based Visual Controller And Data Logger System, Xiao-Fang Qi

Theses

This thesis paper describes the firmware design, instead of the hardware logic design, makes the machine vision hardware system economical, intelligent and expandable. It shows the construction and testing of a novel remote low speed machine vision control system, which also has functions as data logger and is capable of auto control. The system has 9 analog input channels available, and more. It also has 4 digital output channels for controlling external devices. This work also implemented a way to transfer the grabbed image to a PC/XT. In the 256 graphics mode of the VGA, 64 B&W gray levels can …

A Self Testing Strategy For The Wafer Scale Hierarchical Memory Architecture, Maremanda V. R. Rao

Theses

Since the early 1960's, semiconductor chips have matured from single transistor devices to one million transistors per chip. The integration has been achieved by reducing transistor dimensions, and by increasing chip sizes. However, physical limits are being reached as submicrometre dimensions are approached. Fault tolerance has to be used to maintain the increase in the chip complexity. Yield improvement is only one of the many possible gains of fault tolerance. The dense integration of logic on a single chip also creates a huge test problem. in recent years a great deal of effort has gone into the development of yield …

The Interconnection Network Analysis Package, Nadeem Sabbar

Theses

This thesis focuses on the development of the Interconnection Network Analysis Package (INAP), and the use of INAP to analyze minimal permutation networks. The INAP code is written in C language using Turbo C compiler. Although the INAP has been used to analyze the subject networks it is not a dedicated system. It gives the user the freedom to create the permutation network from scratch (1-8 inputs and 1-7 stages), and then to process it for any number of stages.

The INAP made the analysis of five input networks easy and efficient. The networks have been analyzed stage by stage. …

A Novel Schottky Barrier Mosfet For Vlsi Applications, Venkata S. Simhadri

Theses

Schottky barrier MOSFETs are expected to offer certain fabrication advantages, low series resistance and the feasibility to go into sub-micron technology without having short-channel effects. A p-channel MOSFET using Schottky contacts as source and drain is reviewed theoritically. The limitations of the device arising from the oxide offset between source/channel is studied with the help of one dimensional simulation SEDAN. The process sequence leads to an offset between source and channel. The performance of the SBMOSFETs with and without offset is estimated using two dimensional device simulation program PISCES-II for PtSi and IrSi as source and drain material. A novel …

Microengineered Thermal Conductivity Vacuum Pressure Sensor, Sanjay Talreja

Theses

This thesis details the first designs for microengineered vacuum pressure gauges based on silicon microelectronic technology. A monolithic polysilicon air-bridge structure (supported at both ends), within a Wheatstone bridge circuit, is used as a pressure sensor. The device utilizes the change of the thermal conductivity of a gas with ambient gas pressure. The doubly supported beam functions as a temperature sensitive resistor with a negative temperature coefficient of resistivity. Thermal change of resistance monitored as a measure of ambient pressure constitutes the basis of operation for this sensor. The sensor operates over the pressure ranging from 1 Torr to 10 …

Simulation And Analysis Of Integrated Lans For Hospital Environment, Naveen K. Verma

Theses

Hospitals generate a large number of data sets of different types and formats and it is required to integrate these data sets for their rapid and simultaneous communication in order for a better treatment of patients and to cut the escalating costs. A better approach to meet this requirement is to have a distributed system linked all together with a high capacity LAN using an efficient integration method.

This thesis begins by studying the characteristic feature and suitability of Queued Packet & Synchronous Exchange (QPSX) network architecture. The network models are simulated for QPSX, Ethernet and Token Bus networks for …

Reflection And Transmission Through Achiral-Chiral Interface, Jia-Feng Wang

Theses

Electromagnetic wave propagation through an achiral-chiral interface is analyzed via Maxwell's equations using the appropriate boundary conditions. Experimental data for reflected power from achiral-chiral interface was found to be in qualitative agreement with the analytical results. In addition, coupled mode equations for chiral cladding waveguides were derived and solved for weak coupling. The experimental results of chiral cladding waveguides show that an average of about 0.2° per cm in polarization rotation occurred. These waveguides were fabricated by using spin-coating deposition. The sense of the rotation was found to be independent of the handness of the cladding chirality, which was predicted …

Measurement Of Cluster Size By Retarding Potential And Time-Of- Flight Methods In An Ionized Cluster Beam Deposition System, Yung-Kuan Wang

Theses

The goal of this research was to study the mass distribution of ions generated in the Ionized Cluster Beam (ICB) deposition system. The ICB deposition method has been used to form high quality films of metals and other materials. It was postulated that the clusters consisting of hundreds and thousands of atoms produced by vapor expansion in the ICB source are responsible for the superior film properties. However, consistent experimental evidence concerning the cluster mass distribution, or even the existence of such clusters in the ICB apparatus, was lacking.

Two methods of cluster ion mass spectroscopy were used in this …

Modeling And Analysis Of Electrical Properties Of Polycrystalline Silicon Films, Yunsheng Wang

Theses

In recent years, investigations on polysilicon grain structures have shown that all polysilicon films by LPCVD which are most used in today's integrated circuits are columnar in structure. In this work, a square columnar grain structure has been considered to model electrical properties of polycrystalline silicon films instead of all previous one-dimensional grain structure models. By solving Poisson's equation with certain boundary conditions, we find that the barrier height at the corners of the grain is lower than that in the one-dimensional case. Assuming the trapping state energy level as constant, we also find that this level has a value …

Microengineered Silicon Beam Switch For Fiber Optics, Hsu-Nien Yang

Theses

A novel microelectromechanical actuator has been designed for moving an optical input fiber into alignment with one of three stationary output fibers. This switching device thus can connect an input optical port to one of 3 selected optical ports. The actuation force is created by a vertical-drive armature measuring 0.5x2.7 mm² mechanically tethered to the input optical fiber. A force of 2.33 mN is obtained from the linear acturator when the vertical stator armature gap is one micron and the applied three phase voltage is 140 Volts. The required force is a function of the input fiber length, e.g. …

Neural Net Classification Of States In Finite State Vector Quantization, Zhigang Zhang

Theses

In this thesis, a new image coding technique based on Neural Network Finite State Vector Quantization(NNFSVQ) is presented. The new design takes advantage of the high interblock spatial correlation of pixels in typical grey-level images, in addition to intrablock correlation already exploited by vector quantization (VQ). Although many FSVQ require large memory space for the storage of the numerous state codebooks, the memory space requirement of NNFSVQ can be reduced by a very large factor (about 10²-10³) to manageable size without impairing image quality. Simulation experiments have shown that by using NNFSVQ the bit rate can …

Optimization Of Bandwidth Allocation In Atm Nets Through Simulated Annealing, Chien-Long Hou

Theses

Optimization of Bandwidth Allocation in ATM network is considered in this thesis. We address the problem of determining optimal bandwidth allocation in such BISDN's that adopt ATM as their basic switching. technique by using Simulated Annealing. Computer simulation shows that this optimal policy leads to the configuration which yields the minimum average packet delay.

An Optically Powered Cmos On-Chip Power Supply, Jaeyong Jeong

Theses

This thesis presents an optically powered CMOS on-chip power supply for CMOS IC applications. There exists a need for specialized chips that are located remotely and are powered by light supplied through fiber-optic cabling. An optically powered CMOS on-chip power supply circuit described in this thesis is composed of three subcircuits; light to voltage converter circuit, clock pulse generator circuit, and voltage multiplier circuit. Each subcircuit has been analyzed and designed, and simmulated using SPICE 2G.5/6 with 3pm CMOS SPICE parameters from the MOSIS. The circuits layout has been done using MAGIC according to the MOSIS scalable CMOS design rules. …

A Transputer Based Distributed Graphics Display, Ramana V. Kattula

Theses

The design of a transputer based graphics display is discussed. The problems associated with the single processor graphics systems are described. A solution based on multiple transputers is proposed. The transputer based graphics display described is a general purpose graphics system which can achieve any required compute performance and drawing performance without using special hardware. The display resolution and color depth can be enhanced as per the user requirements with little or no change in hardware.