Electrical and Electronics Commons^™

Cmos Design Of An 8-Bit 1ms/S Successive Approximation Register Adc, Ameya Vivekanand Ganguli

Master's Theses

Rapid evolution of integrated circuit technologies has paved a way to develop smaller and energy efficient biomedical devices which has put stringent requirements on data acquisition systems. These implantable devices are compact and have a very small footprint. Once implanted these devices need to rely on non-rechargeable batteries to sustain a life span of up to 10 years. Analog-to-digital converters (ADCs) are key components in these power limited systems. Therefore, development of ADCs with medium resolution (8-10 bits) and sampling rate (1 MHz) have been of great importance.

This thesis presents an 8-bit successive approximation register (SAR) ADC incorporating an …

Real-Time Fault Detection And Reconfiguration Of A Three-Phase Electric Motor Drive, Danyal Mohammadi

Boise State University Theses and Dissertations

Variable-frequency drives (VFDs) are widely used for control of electrical machines such as induction motors (IMs) or permanent-magnet synchronous motors (PMSMs). Similar to other electrical devices, these drives are subject to failure. Several types of faults are associated with VFDs. For instance, faults such as an open-switch fault, a short-circuit switch fault are the two common faults in VFDs. These faults can yield catastrophic consequences if proper remedial action is not taken.

A unique remedial topology for the post-fault period and a new pulse width modulation (PWM) strategy are proposed so that not only the motor drive can continue the …

An Electrooculography Prosthetic Control System, Walker Arce

UNO Student Research and Creative Activity Fair

For many surface EMG (sEMG) prosthetic control systems, the muscles on the affected limb are used to trigger the control system. This can lead to fatigue in the user as they have to maintain continuous muscle activation and coactivation in order to achieve prosthetic control [3]. The crux of any prosthetic control system is the human machine interface that is developed, and at present many control systems have complicated interfaces that limit the degrees of freedom of the prosthetics. This study focuses on the development of a low-cost prosthetic control peripheral that is compatible with the prosthetics developed by Dr. …

Experimental Study And Modeling Of The Gm-I Dependence Of Long-Channel Mosfets, Michael Fong Cheng

Master's Theses

This thesis describes an experimental study and modeling of the current-transconductance dependence of the ALD1106, ALD1107, and CD4007 arrays. The study tests the hypothesis that the I-gm dependence of these 7.8 µm to 10 µm MOSFETs conforms to the Advanced Compact Model (ACM). Results from performed measurements, however, do not support this expectation. Despite the relatively large length, both ALD1106 and ALD1107 show sufficiently pronounced ‘short-channel’ effects to render the ACM inadequate. As a byproduct of this effort, we confirmed the modified ACM equation. With an m factor of approximately 0.6, it captures the I-gm dependence with sub-28% maximum error …

The Concept Of Substrate Integrated Circularly Polarized Horn Antennas, Venkata Naga Kalyan Ram Akunuru

All Graduate Theses, Dissertations, and Other Capstone Projects

In this thesis, a new type of Substrate Integrated Waveguide for Horn Antennas is proposed for implementing circularly polarization on printed circuit boards. E-plane type of circuits cannot be realized by the conventional substrate integrated waveguide. Substrate integrated E-plane waveguide consists of two circuit boards attached to each other by the two copper strips which are inserted in between two circuit boards, where plated through holes are penetrated through them along the transmission direction. The plated through holes and copper strips altogether played as side walls of a conventional waveguide to support longitudinal and vertical currents. Circular Polarization has its …

Autonomous Combat Robot, Andrew J. Szabo Ii, Chris Heldman, Tristin Weber, Tanya Tebcherani, Holden Leblanc, Fabian Ardeljan

Williams Honors College, Honors Research Projects

This honors project will also serve as an engineering senior design project.

The objective is to design and build the software and electrical systems for a 60 lb weight class combat robot that will function autonomously and outperform manually driven robots during competition.

While running autonomously, the robot will use LiDAR sensors to detect and attack opponent robots. This robot will also be able to be remote controlled in manual mode. This will mitigate the risk in case the autonomy or sensors fail. LED lights on the robot will indicate whether it is in autonomous or manual mode. The system …

S.A.V.E. M.E., Taylor Davis, Kelly Nicole O'Neill, Adrianna M. Dunlap, Parsa Esshaghi Bayat

Williams Honors College, Honors Research Projects

S.A.V.E. M.E. stands for Submerged Automated Vehicular Elevation Minor Extraction or alternatively a Home Swimming Pool Rescue Device. The objective of this project is to design and prototype a system that will make unattended swimming pools through detecting a victim’s presence, deploying a means to save the victim, and alerting others nearby of the situation. This system encompasses sensors and devices within the pool and an alarm system outside of the pool. Upon detection of a sufficiently sized object entering the pool when the system is armed, a device will maneuver to the victim and deploy a flotation device that …

Investigating The Effect Of Detecting And Mitigating A Ring Oscillator-Based Hardware Trojan, Lakshmi Ramakrishnan

Electrical Engineering Theses and Dissertations

The outsourcing of the manufacturing process of integrated circuits to fabrications plants all over the world has exposed these chips to several security threats, especially at the hardware level. There have been instances of malicious circuitry, such as backdoors, being added to circuits without the knowledge of the chip designers or vendors. Such threats could be immensely powerful and dangerous against confidentiality, among other vulnerabilities.

Defense mechanisms against such attacks have been probed and defense techniques have been developed. But with the passage of time, attack techniques have improved immensely as well. From directly observing the inputs or outputs, adversaries …

Techniques Of Energy-Efficient Vlsi Chip Design For High-Performance Computing, Zhou Zhao

LSU Doctoral Dissertations

How to implement quality computing with the limited power budget is the key factor to move very large scale integration (VLSI) chip design forward. This work introduces various techniques of low power VLSI design used for state of art computing. From the viewpoint of power supply, conventional in-chip voltage regulators based on analog blocks bring the large overhead of both power and area to computational chips. Motivated by this, a digital based switchable pin method to dynamically regulate power at low circuit cost has been proposed to make computing to be executed with a stable voltage supply. For one of …

Cmos Radioactive Isotope Identification With Multichannel Analyzer And Embedded Neural Network, Samuel Murray

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

A radiation detection and identification system is designed and implemented to perform gamma ray spectroscopy on radioactive sources and identify which isotopes are present in the sources. A multichannel analyzer is implemented on an ASIC to process the signal produced from gamma rays detected by a scintillator and photomultiplier tube and to quantize the gamma ray energies to build a histogram. A fast, low memory embedded neural network is implemented on a microcontroller ASIC to identify the isotopes present in the gamma ray histogram produced by the multichannel analyzer in real time.

Advisors: Sina Balkir and Michael W. Hoffman

Arm Mke1xf Mcu Replatform, Nathan Hong, Derek Lung, Japsimran Singh, Bevin Tang

Computer Engineering

After Cal Poly Racing’s electrical team began to hit the technical limits of the ADC and other I/O features of the current 8-bit Atmel AT90 microcontroller unit, it became clear that an upgrade was due. This replatforming project takes the functionalities of the old, 8-bit architecture, and aims to provide a 32-bit version using the ARM MKE1xF MCU. With the idea of having a working PCB as a stretch goal, the scope of the library development was limited to enable base functionality. Thus, the only libraries developed were for the Timer, ADC, SPI, UART, and CAN. Additionally, this document discusses …

High-Speed Single-Channel Sar Adc Using Coarse And Fine Comparators With Background Comparator Offset Calibration, Guanhua Wang

Electrical Engineering Theses and Dissertations

A 1-GS/s 8-bit single-channel successive-approximation-register (SAR) analog-to-digital converter (ADC) using coarse and fine comparators with fully background comparator offset calibration is presented. Low-power coarse comparators and low-noise fine comparators are both employed to improve the comparator power efficiency. Non-binary digital-to-analog converter (DAC) with redundancy is employed to tolerate possible errors in the most-significant-bit (MSB) decisions. A novel comparator offset calibration scheme is proposed to remove the offsets between the different comparators, without slowing down the speed of the SAR conversion. The prototype ADC is simulated in a 28 nm CMOS technology and achieves an SNDR of 42.13 dB near Nyquist …

Electronic Drum Machine (E.D.M), Nyssa Marie Backes

Electrical Engineering

Many people argue that a drummer plays the most important role in a band of any genre. During live performances, the other band members rely on the drummer to keep the song moving forward at a proper steady pace. Even in recorded music, drums help listeners sing and dance along with their favorite songs. Thus, achieving success as a band, both in terms of recordings and live shows, absolutely requires a drummer. So, if a band does not have a drummer, and cannot afford the hefty cost of hiring a session drummer, a touring drummer, or both, how can they …

Ball Oscillating Bouncer, Eric Blok, Daniel Altemese, Ryan Nowacki, Maram Qurban

Williams Honors College, Honors Research Projects

The purpose of this report is to document the need, objectives, marketing and engineering requirements, as well as validate the design of an autonomous control device capable of continuously bouncing a table tennis ball on a paddle. This includes the design of a self correcting system using lightweight materials, and as few sensors and components as possible to achieve a compact, portable design. To accomplish this, the system is designed to react to a ball falling from as short a distance as 10 centimeters above the paddle, meaning all sensor processing, control processing, and motor drives should be able to …

Asynchronous 3d (Async3d): Design Methodology And Analysis Of 3d Asynchronous Circuits, Francis Corpuz Sabado

Graduate Theses and Dissertations

This dissertation focuses on the application of 3D integrated circuit (IC) technology on asynchronous logic paradigms, mainly NULL Convention Logic (NCL) and Multi-Threshold NCL (MTNCL). It presents the Async3D tool flow and library for NCL and MTNCL 3D ICs. It also analyzes NCL and MTNCL circuits in 3D IC. Several FIR filter designs were implement in NCL, MTNCL, and synchronous architecture to compare synchronous and asynchronous circuits in 2D and 3D ICs. The designs were normalized based on performance and several metrics were measured for comparison. Area, interconnect length, power consumption, and power density were compared among NCL, MTNCL, and …

Design And Simulation Of An 8-Bit Successive Approximation Register Charge-Redistribution Analog-To-Digital Converter, Sumit K. Verma

Electrical Engineering Theses

The thesis initially investigates the history of the monolithic ADCs. The next chapter explores the different types of ADCs available in the market today. Next, the operation of a 4-bit SAR ADC has been studied. Based on this analysis, an 8-bit charge-redistribution SAR ADC has been designed and simulated with Multisim (National Instruments, Austin, TX). The design is divided into different blocks which are individually implemented and tested. Level-1 SPICE MOSFET models representative of 5μm devices were used wherever individual MOSFETs were used in the design. Finally, the power dissipation during the conversion period was also estimated. The supply voltage …

Autonomous Speed Control For Kia Optima, Andrew J. Combs, Kyle Fugatt, Kevin Mcfall

The Kennesaw Journal of Undergraduate Research

The standard method for speed control is the cruise control system built into most modern vehicles. These systems employ a PID controller which actuates the accelerator thus, in turn, maintains the desired vehicle speed. The main drawback of such a system is that typically the cruise control will only engage above 25 mph. The goal of this paper is to describe a system which we used to control vehicle speed from a stop to any desired speed using an Arduino microcontroller and a CAN BUS shield, from where autonomous features can be built upon. With this system, we were able …

Logic Tiles, Andrew Wheeler, Tristan Lennertz

Computer Engineering

This project was originally conceived by Professor Andrew Danowitz as he considered the restructuring of the introductory digital design course at Cal Poly. As it stands now, students apply their knowledge of boolean algebra and combinatorial logic through the programming of a Field Programmable Gate Array (FPGA) using a Hardware Descriptive Language (HDL). While this is the industry standard for designing large, complex digital circuits, and is an fundamental skill to learn, there is a lack of actual circuit building in the process that can cause a disconnect from theory to application for students who have little-to-no experience with digital …

Wireless Audio Bridge, Daniel L. Hodges

Electrical Engineering

Bluetooth, a wireless technology standard used to exchange data using radio transmissions, has made a significant impact on the audio technology industry, specifically the way people listen to music. This technology enables a wireless listening experience, eliminating the need for wires or cables between audio devices as previously required. Audio can transmit from a cellphone or laptop (an output device) to a pair of headphones or speakers (an input device) without any physical connection. Compared to alternative wireless listening solutions (i.e. FM transmitter, radio broadcast), Bluetooth offers greater reliability, audio fidelity, portability, and ease of use. To obtain this functionality, …

Music Synthesizer Senior Project: Individual Report, Bryan Bellin

Electrical Engineering

No abstract provided.

Remote Cable Gantry, Allen L. Bailey

Electrical Engineering

The Remote Cable Gantry is a robotic system that was initially intended to aid in the art of aerial videography. It was designed to enable novice and expert users alike to capture both video footage and audio from perspectives unachievable by current methods. This system uses a series of cables to control the position of a camera gimbal in a defined 3D space and, as a self-contained unit, is portable and easy to use. The Remote Cable Gantry offers a quiet, intuitive, and safe alternative to existing technology, which has been limiting the market and potential of aerial photography and …

Music Synthesizer Senior Project: Danalog, Vikrant A. Marathe

Electrical Engineering

The Danalog is a 25 key portable digital music synthesizer that uses multiple synthesis methods and effects to generate sounds. Sound varieties included three synthesis methods including FM, subtractive, and sample-based, with up to eight adjustable parameters, at least four effects, including reverb, chorus, and flange, with five adjustable parameters, and at least two note polyphony, and a five band equalizer. The user would be able to adjust these effects using digital encoders and potentiometers and view the settings on two LCD screens. The finals project was unable to meet the original design requirements. The FM synthesis method was primarily …

Danalog: Digital Music Synthesizer, Evan R. Lew

Electrical Engineering

The Danalog is a 25 key portable digital music synthesizer that uses multiple synthesis methods and effects to generate sounds. Sound varieties included three synthesis methods including FM, subtractive, and sample-based, with up to eight adjustable parameters, at least four effects, including reverb, chorus, and flange, with five adjustable parameters, and at least two note polyphony, and a five band equalizer. The user would be able to adjust these effects using digital encoders and potentiometers and view the settings on two LCD screens.

The finals project was unable to meet the original design requirements. The FM synthesis method was primarily …

An Exact Analysis For Four-Order Acousto-Optic Bragg Diffraction Which Incorporates Both Incident Light Angle And Sound Frequency Dependencies, Adeyinka Sunday Ademola

Electrical Engineering Theses

This thesis extends the prior work which produced an exact solution to the four-order acousto-optic (AO) Bragg cell with assumed fixed center frequency and with exact Bragg angle incident light. The extension predicts the model that incorporates the dependencies of both the input angle of light and the sound frequency. Specifically, a generalized 4^th order linear differential equation (DE), is developed from a simultaneous analysis of four coupled AO system of DEs. Through standard methods, the characteristic roots, which requires solving a quartic equation, is produced. Subsequently, a derived system of homogeneous solutions, which absorbs the roots obtained using …

Project Pradio, Trigg T. La Tour

Computer Science and Computer Engineering Undergraduate Honors Theses

This paper examines the design and manufacturing of a device that allows two or more users to share a wireless audio stream. Effectively, this allows a group of people to listen to the same audio in a synchronized manner. The product was unable to be completed in the allotted time. Regardless, significant progress was made and valuable insight into the circuit board design process was gained.

Design Of A Folded Cascode Operational Amplifier In A 1.2 Micron Silicon-Carbide Cmos Process, Kyle Addington

Electrical Engineering Undergraduate Honors Theses

This thesis covers the design of a Folded Cascode CMOS Operational Amplifier (Op-Amp) in Raytheon’s 1.2-micron Silicon Carbide (SiC) process. The use of silicon-carbide as a material for integrated circuits (ICs) is gaining popularity due to its ability to function at high temperatures outside the range of typical silicon ICs. The goal of this design was to create an operational amplifier suitable for use in a high temperature analog-to-digital converter application. The amplifier has been designed to have a DC gain of 50dB, a phase margin of 50 degrees, and a bandwidth of 2 MHz. The circuit’s application includes input …

Hexarray: A Novel Self-Reconfigurable Hardware System, Fady Hussein

Boise State University Theses and Dissertations

Evolvable hardware (EHW) is a powerful autonomous system for adapting and finding solutions within a changing environment. EHW consists of two main components: a reconfigurable hardware core and an evolutionary algorithm. The majority of prior research focuses on improving either the reconfigurable hardware or the evolutionary algorithm in place, but not both. Thus, current implementations suffer from being application oriented and having slow reconfiguration times, low efficiencies, and less routing flexibility. In this work, a novel evolvable hardware platform is proposed that combines a novel reconfigurable hardware core and a novel evolutionary algorithm.

The proposed reconfigurable hardware core is a …

The Effect Of Power Supply Ramp Time On Sram Puf's, Abdelrahman T. Elshafiey Mr.

Electrical and Computer Engineering ETDs

Physical unclonable functions (PUFs) are security primitives that exploit the device mismatches. PUFs are a promising solution for hardware cryptography and key storage. They are used in many security applications including identification, authentication and key generation. SRAM is one of the popular implementations of PUFs. SRAM PUFs offer the advantage, over other PUF constructions, of reusing resources (memories) that already exist in many designs.

In this thesis, for the first time, it is demonstrated that the start-up value of an SRAM PUF could be different depending on the SRAM power supply rising time. An analytical model has been developed to …

Stringless Guitar, Kue Z. Yang, Anthony Batey, Dominic Mercorelli, Nathaniel Hawk

Williams Honors College, Honors Research Projects

The aim of this project is to improve the design of a typical guitar by designing a digital stringless guitar. Due to the nonlinearities inherent in a guitar, it would be difficult to reproduce guitar tones by summing harmonic components; therefore, digital samples of guitar tones were taken in order to preserve these unique and wonderfully sounding tones. These digital samples were stored in the guitar and used to produce its tones when played. The digital guitar includes fingerboard position sensors as well as strum sensors for each string. The fingerboard position sensors detect the player’s fingers at discrete positions. …

Accumulator Volume Sensor Final Project Report, Chris Naughton, Kinwei Yu, Michael George

Mechanical Engineering

Accumulator Volume Sensing Team has developed two sensor designs aimed at detecting the position of the piston within a 4024 accumulator. The two designs include the use of a Renishaw LMA10 magnetic encoder and a SpectraSymbol HotPot linear potentiometer. The magnetic encoder solution drastically increases the accuracy of sensing the piston position compared to the current solutions of both a string-pot and linear variable differential transformer while costing slightly less. The linear potentiometer seeks to provide a solution that drastically decreases the cost compared to the present sensing methods. Both designs call for a modification to one half of the …