Electrical and Electronics Commons^™

Interferometry In Fmcw Radars, Assid Nait, Theodore Grosch

The Kennesaw Journal of Undergraduate Research

interferometry is used in many fields using all frequencies of the electromagnetic spectrum and sound waves. In this study, data was collected from an FMCW radar is used at multiple heights above a flat surface on which sat a single retroreflector. These data were post-processed to discover the signal obtained from the target and then the phase form the radar at multiple locations was compared. Using the known geometry and measured phase, we find the interferometry is possible using a freerunning radar under certain geometric conditions.

Deep Models For Improving The Performance And Reliability Of Person Recognition, Sobhan Soleymani

Graduate Theses, Dissertations, and Problem Reports (ETD)

Deep models have provided high accuracy for different applications such as person recognition, image segmentation, image captioning, scene description, and action recognition. In this dissertation, we study the deep learning models and their application in improving the performance and reliability of person recognition. This dissertation focuses on five aspects of person recognition: (1) multimodal person recognition, (2) quality-aware multi-sample person recognition, (3) text-independent speaker verification, (4) adversarial iris examples, and (5) morphed face images. First, we discuss the application of multimodal networks consisting of face, iris, fingerprint, and speech modalities in person recognition. We propose multi-stream convolutional neural network architectures …

Re-Design Of Precision Signal Conditioning Circuit For Detecting Schumann Resonance, Rohith Bikkina

Graduate Theses, Dissertations, and Problem Reports (ETD)

Extremely low frequencies signals are waves between 3 to 30Hz and corresponding wavelengths between 10,000 to 100,000 kilometers. The specific signals used here are generated from lightning and are excited at frequencies around 8Hz, 14Hz, 20Hz. These are often called Schumann Resonance frequencies. Several stations have been built around the world for identifying ELF waves. All of those required a sparsely populated area that was far away from electric power lines because of interference from electric noise at 50 Hz and 60Hz. This project develops and tests an amplifier and filter circuit that should assist in identifying the Schumann Resonance …

Analysis Of Millimeter-Wave Networks: Blockage, Antenna Directivity, Macrodiversity, And Interference, Enass Hriba

Graduate Theses, Dissertations, and Problem Reports (ETD)

Due to its potential to support high data rates at low latency with reasonable interference isolation because of signal blockage at these frequencies, millimeter-wave (mmWave) communications has emerged as a promising solution for next-generation wireless networks. MmWave systems are characterized by the use of highly directional antennas and susceptibility to signal blockage by buildings and other obstructions, which significantly alter the propagation environment. The received power of each transmission depends on the direction the corresponding antennas point and whether the signal’s path is line-of-sight (LOS), non-LOS (i.e., partially blocked), or completely blocked. A key challenge in modeling blocking in mmWave …

Multibeam Array Antenna For Base Station In The Fifth-Generation Mobile Communication System, Intan Izafina Idrus

Student Works (2020-2029)

Research on the fifth-generation (5G) mobile communication system has been accelerated to meet the standardization of the International Telecommunications Union for higher data traffic and higher data rates. The main requirements of the 5G mobile communication systems are the utilization of millimeter waves, the deployment of small cells, and the use of multibeam array antennas for multiple-input multiple-output schemes. Multibeam array antennas play an important role in developing a new base station to enhance system capacity, improve network coverage, and reduce co-channel interference. The main objective of this thesis is to design a single-layer multibeam array antenna at 28 GHz …

A Simplified Accuracy Enhancement To The Saleh Am/Am Modeling And Linearization Of Solid-State Rf Power Amplifiers, Haider Al-Kanan, Fu Li

Electrical and Computer Engineering Faculty Publications and Presentations

The Saleh behavioral model exhibits high prediction accuracy for nonlinearity of traveling-wave tube power amplifiers (TWT-PAs). However, the accuracy of the Saleh model degrades when modeling solid-state power amplifiers (SSPAs) technology. In addition, the polynomial expansion of the Saleh model consists of only odd-order terms as analyzed in this work. This paper proposes a novel model accuracy enhancement for the Saleh amplitude-to-amplitude (AM/AM) model when applied to radio frequency (RF) SSPAs. The proposed model enhancement accounts for the second-order intermodulation distortion, which is an important nonlinearity challenge in wideband wireless communications. The proposed static AM/AM model is a three-parameter rational …

Cybersecurity Strategy Against Cyber Attacks Towards Smart Grids With Pvs, Fangyu Li, Maria Valero, Liang Zhao, Yousef Mahmoud

KSU Proceedings on Cybersecurity Education, Research and Practice

Cyber attacks threaten the security of distribution power grids, such as smart grids. The emerging renewable energy sources such as photovoltaics (PVs) with power electronics controllers introduce new potential vulnerabilities. Based on the electric waveform data measured by waveform sensors in the smart grids, we propose a novel cyber attack detection and identification approach. Firstly, we analyze the cyber attack impacts (including cyber attacks on the solar inverter causing unusual harmonics) on electric waveforms in distribution power grids. Then, we propose a novel deep learning based mechanism including attack detection and attack diagnosis. By leveraging the electric waveform sensor data …

Multimodal Representation Learning And Set Attention For Lwir In-Scene Atmospheric Compensation, Nicholas M. Westing, Kevin C. Gross, Brett J. Borghetti, Christine M. Schubert Kabban, Jacob Martin, Joseph Meola

Faculty Publications

A multimodal generative modeling approach combined with permutation-invariant set attention is investigated in this paper to support long-wave infrared (LWIR) in-scene atmospheric compensation. The generative model can produce realistic atmospheric state vectors (T;H₂O;O₃) and their corresponding transmittance, upwelling radiance, and downwelling radiance (TUD) vectors by sampling a low-dimensional space. Variational loss, LWIR radiative transfer loss and atmospheric state loss constrain the low-dimensional space, resulting in lower reconstruction error compared to standard mean-squared error approaches. A permutation-invariant network predicts the generative model low-dimensional components from in-scene data, allowing for simultaneous estimates of the atmospheric state and TUD …

Learning Deep Architectures For Power Systems Operation And Analysis, Mahdi Khodayar

Electrical Engineering Theses and Dissertations

With the rapid increase in size and computational complexities of power systems, the need for powerful computational models to capture strong patterns from energy datasets is emerged. In this thesis, we provide a comprehensive review on recent advances in deep neural architectures that lead to significant improvements in classification and regression problems in the area of power engineering. Furthermore, we introduce our novel deep learning methodologies proposed for a large variety of applications in this area. First, we present the interval deep probabilistic modeling for wind speed forecasting. Incorporating the Rough Set Theory into deep neural networks, we create an …

Distance Estimation Using Ofdm Signals For Ultrasonic Positioning, Kyman Huang

Master's Theses

This paper describes a method of estimating distance via Time-of-Flight (TOF) measurement using ultrasonic Orthogonal Frequency Division Multiplexing (OFDM) signals. Using OFDM signals allows the signals and their sub-carriers to remain orthogonal to each other while continuously transmitting. This estimation method is based on the change of phase of a traveling wave as it propagates through a medium (air for ultrasonic signals). By using signals containing multiple tones, the phase change between each frequency component is slightly different. This phase difference is dependent on the distance traveled and can thus be used to estimate distance. This paper studies the impact …

The Design, Testing, And Analysis Of A Constant Jammer For The Bluetooth Low Energy (Ble) Wireless Communication Protocol, Aiku Shintani

Master's Theses

The decreasing cost of web-enabled smart devices utilizing embedded processors, sensors, and wireless communication hardware have created an optimal ecosystem for the Internet of Things (IoT). IEEE802.15.4, IEEE802.11ah, WirelessHART, ZigBee Smart Energy, Bluetooth (BT), and Bluetooth Low Energy (BLE) are amongst the most commonly used wireless standards for IoT systems. Each of these standards has tradeoffs concerning power consumption, range of communication, network formation, security, reliability, and ease of implementation. The most widely used standards for IoT are Bluetooth, BLE, and Zigbee. This paper discusses the vulnerabilities in the implementation of the PHY and link layers of BLE. The link …

Remedying Sound Source Separation Via Azimuth Discrimination And Re-Synthesis, Ruairí De Fréin

Conference papers

Commercially recorded music since the 1950s has been mixed down from many input sound sources to a two- channel reproduction of these sources. The effect of this approach is to assign sources to locations in a stereo field using a pan- position for each source. The Adress algorithm is a popular way of extracting individual music sound sources from a stereo mixture. A drawback of the Adress algorithm is that when time- frequency components in the stereo mixture are shared between two or more sources, calculating the inter-aural intensity scaling parameter for each source for that time-frequency component is challenging. …

Remedying Sound Source Separation Via Azimuth Discrimination And Re-Synthesis, Ruairí De Fréin

Conference papers

Commercially recorded music since the 1950s has been mixed down from many input sound sources to a two-channel reproduction of these sources. The effect of this approach is to assign sources to locations in a stereo field using a pan-position for each source. The Adress algorithm is a popular way of extracting individual music sound sources from a stereo mixture. A drawback of the Adress algorithm is that when time-frequency components in the stereo mixture are shared between two or more sources, calculating the inter-aural intensity scaling parameter for each source for that time-frequency component is challenging. We show how …

Heel Down And Toe-Off Time Measured With Ultrasonic Doppler System And Force Plate Sensor, Sabin Timsina

Honors Theses

Collie Box is a medical device that measures the gait parameters of the person walk- ing in front of it. This device uses the Ultrasonic Doppler system to extract the heel-contact and toe-off times of a person walking within the range of 2-10 meters. These times are used to determine the leg’s swing phase and double stance times. The ultrasonic transducer of 10mm diameter is driven at 40kHz. At the time of the heel-contact and toe-off, foot velocity is zero while the torso part of the human body is still in motion. The wide directivity of 10mm diameter ultrasonic transducer …

Methods Of High-Fidelity, High-Efficiency Class-D Audio Amplification, Kaleb Kassaw

Electrical Engineering Undergraduate Honors Theses

Gallium nitride-based field effect transistors (FETs) have opened a path for full-frequency-range class-D audio amplifiers with low distortion and noise, thanks to their ability to switch at much higher frequencies than that of the upper range of human hearing. Compared to traditional silicon-based transistors, GaN-based transistors offer superior efficiencies, particularly at power levels below their maxima. Paired with an analog-to-digital converter, digital signal processor, and pulse-code modulation to pulse-width modulation converter, these transistors are used to design and implement a solid-state amplifier capable of generating 100 watts of output through speakers with an impedance of 8 ohms using a 1-volt …

A Power Constrained 433-Mhz Low Noise Amplifier, Pablo Alvarez Arellano

Graduate Theses and Dissertations

Within wireless communication systems, low noise amplifiers are critical for the performance of receivers. They are primarily responsible for providing enough gain while adding little noise to overcome the noise of the subsequent stages. The LNA presented here is part of a battery-powered transceiver meant to measure crop nutrient data and relay the information. Therefore, power consumption and area become import considerations. To design for a specific power level, a power-constrained noise optimization method is used. The method sizes the amplifying transistor for a fixed source impedance, power dissipation, technology, and operating frequency. The chosen topology is the cascode stage …

Partial Discharge Classification For Xlpe Cable Joints Using K Nearest Neighbors Algorithm, Mohd Salleh Muhammad Shairazi

Student Works (2020-2029)

Due to excellent mechanical and electrical properties, cross-linked polyethylene (XLPE) cables are commonly used in the power industry. However, cable joints are the weakest part of XLPE cables and are susceptible to insulation failures. Cable joint insulation breakup can cause large losses for power companies. It is therefore necessary to evaluate the consistency of the insulation for early detection of insulation failure. It is known that there is a link between the partial discharge (PD) and the quality of the insulation. PD analysis is an important tool for assessing the quality of insulation in cable joints. In this study, XLPE …

Calibration To Mitigate Near-Field Antennas Effects For A Mimo Radar Imaging System, Ha Hoang, Matthias John, Patrick Mcevoy, Max Ammann

Articles

A calibration method for a high-resolution hybrid MIMO turntable radar imaging system is presented. A line of small metal spheres is employed as a test pattern in the calibration process to measure the position shift caused by undesired antenna effects. The unwanted effects in the antenna near-field responses are analysed, modelled and significantly mitigated based on the symmetry and differences in the responses of the MIMO configuration.

Kettlebell Ultra, Elissa Peters, Kathryn Wegman, Daniel Basch, Mason Pastorius

Williams Honors College, Honors Research Projects

This project will consist of an attachment to an average kettlebell that will track the number of repetitions that the user has performed. The device will send this data over Bluetooth to a smart phone application so the user can track their workout accurately.

Digital, Automated Reactive Target System, Nicholas Haas, Saipranay Vellala, Trandon Ware, Thomas Martin

Williams Honors College, Honors Research Projects

In this era, technology is woven into almost every facet of our leisure activities. Although technology has innovated hobbies ranging from chess to soccer, the art of shooting has been neglected. Unnecessary insufficiency such as bullet ricochets off of mechanical steel targets, ineffective progress tracking, and general inaccessibility to outdoor training facilities are all improvable areas of this sport. The Dynamic Automated Reactive Target (D.A.R.T) System aims to fill some of these gaps and help modernize recreational marksmanship. Modeling the system after a dueling tree will optimize the use of the system and allow for different training models to challenge …

Bitbilliards, Grant Reinbolt

Williams Honors College, Honors Research Projects

The goal of the project is to create a billiards table capable of keeping track of the score while simultaneously racking the sunk balls under the table. To achieve this, image processing will be utilized to detect and determine which balls are above and below the table. Upon leaving the table, the balls will be held by gates to prevent the cue ball from entering the re-racking track. The balls will then enter the track and form a queue to be placed back into the triangle underneath the table. A gantry system consisting of an x and y axis will …

Ultra-Wideband Power Amplifier Design For Large Signal Application, Ragavan Krishnamoorthy

Student Works (2020-2029)

Broadband power amplifier design has become one of the most critical enabling block in today’s wireless communication technology. Numerous research efforts have been carried out throughout the years to establish high efficiency over wideband RF transmitter. This research work presents two approaches in achieving ultra-broadband power amplifier for RF transmitter. Firstly, a new technique for the design of ultra-broadband RF power amplifier is introduced, in which a combination of the reactance compensation and third-harmonic tuning are adopted. The design goal is to achieve 40 dBm (10W) output power across a wide frequency bandwidth operation. Theoretical design equations were developed to …

Pseudo-Stereo Audio Processor, Zachariah David Bunce

Electrical Engineering

Due to both technical and resource limitations, non-professional audio production must often record with a single microphone, creating a mono audio signal. Even some originally multi-channel audio files often combine the separate channels into a single channel to save memory. However, this channel limitation makes any music held within the audio duller during listening. The Pseudo-Stereo Audio Processor remedies this situation, introducing a quadrature phase shift onto a given single-channel audio signal, producing multiple phase shifted output signals. These separate fixed-phase output signals are then recombined to produce a variable phase difference, emulated two-channel version of the input signal, allowing …

Underwater Remotely Operated Vehicle Controller With Pid Stability Regulation, Christian E. Aguirre

Electrical Engineering

The earth’s oceans and rivers remain widely unexplored. Hobbyists and companies across the globe invest money and resources into remotely operated vehicles (ROV) to further expand underwater knowledge. Each ROV includes a controller that operates motors and monitors other crucial system vitals. The ROV Controller project makes the process of designing an ROV simpler and more affordable by providing a multi-purpose programmable controller.

The ROV controller features programmable digital inputs/outputs and analog inputs. The controller processes control signals from analog joysticks, digital signals from a gyroscope and utilizes a MUX to expand the analog input capabilities of the Arduino. The …

Design Of A Low-Cost Data Acquisition System For Rotordynamic Data Collection, Gregory S. Pellegrino

Master's Theses

A data acquisition system (DAQ) was designed based on the use of a STM32 microcontroller. Its purpose is to provide a transparent and low-cost alternative to commercially available DAQs, providing educators a means to teach students about the process through which data are collected as well as the uses of collected data. The DAQ was designed to collect data from rotating machinery spinning at a speed up to 10,000 RPM and send this data to a computer through a USB 2.0 full-speed connection. Multitasking code was written for the DAQ to allow for data to be simultaneously collected and transferred …

Development Of A Myoelectric Detection Circuit Platform For Computer Interface Applications, Nickolas Andrew Butler

Master's Theses

Personal computers and portable electronics continue to rapidly advance and integrate into our lives as tools that facilitate efficient communication and interaction with the outside world. Now with a multitude of different devices available, personal computers are accessible to a wider audience than ever before. To continue to expand and reach new users, novel user interface technologies have been developed, such as touch input and gyroscopic motion, in which enhanced control fidelity can be achieved. For users with limited-to-no use of their hands, or for those who seek additional means to intuitively use and command a computer, novel sensory systems …

Fall Detection Using Channel State Information From Wifi Devices, D.M Sameera Palipana

PhDs

Falls among the independently living elderly population are a major public health worry, leading to injuries, loss of confidence to live independently and even to death. Each year, one in three people aged 65 and older falls and one in five of them suffers fatal or non fatal injuries. Therefore, detecting a fall early and alerting caregivers can potentially save lives and increase the standard of living. Existing solutions, e.g. push-button, wearables, cameras, radar, pressure and vibration sensors, have limited public adoption either due to the requirement for wearing the device at all times or installing specialized and expensive infrastructure. …

Distance-Based Cluster Head Election For Mobile Sensing, Ruairí De Fréin, Liam O'Farrell

Conference papers

Energy-efficient, fair, stochastic leader-selection algorithms are designed for mobile sensing scenarios which adapt the sensing strategy depending on the mobile sensing topology. Methods for electing a cluster head are crucially important when optimizing the trade-off between the number of peer-to- peer interactions between mobiles and client-server interactions with a cloud-hosted application server. The battery-life of mobile devices is a crucial constraint facing application developers who are looking to use the convergence of mobile computing and cloud computing to perform environmental sensing. We exploit the mobile network topology, specifically the location of mobiles with respect to the gateway device, to stochastically …

3d Signal Strength Mapping Of 2.4ghz Wifi Networks, Brett D. Glidden

Electrical Engineering

Many commercial businesses operate out of multi-story office buildings. These companies often use many Wi-Fi access points to set up their own wireless network. IT personnel determine proper Wi-Fi access point placement using Wi-Fi strength maps. Conventional Wi-Fi strength maps only provide a two-dimensional view representing the wireless access point's effective range. The signal quality and strength measurements do not include changing vertical elevation. Efficient network layout in a multi-story building requires a system calculating signal quality metrics in three dimensions.

This project involves designing and prototyping a system to achieve 2.4GHz Wi-Fi signal quality measurements in a three-dimensional reference …

Transcribing Braille Code: Learning Equations Across Platforms, Deegan Atha, Courtney Balogh

Purdue Journal of Service-Learning and International Engagement

Deegan Atha, a graduating senior in electrical engineering and a future engineer, is interested in human-centered design and developing technology that helps students engage and be successful in STEM.

Courtney Balogh, a junior in mechanical engineering, is interested in human-centered design and the importance it plays in product development. Deegan and Courtney are members of the Purdue EPICS project, Learning Equations Across Platforms (LEAP). They partnered with the Indiana School for the Blind and Visually Impaired (ISBVI) to develop a braille transcription device and web application that converts braille to print in real time.