Electrical and Electronics Commons^™

Analysis And Design Of A Fully Soft Switched Two-Level Dc-Dc Boost Converter For Electric Vehicle Applications, Amin Mirzaei, Mahdi Rezvanyvardom, Ehsan Najafi

Emirates Journal for Engineering Research

In this paper, a fully soft switched two-level DC-DC Boost converter is proposed. The converter is used only one auxiliary cell to create the soft switching conditions for all semiconductor devices. The auxiliary cell contains one auxiliary switch, one resonant capacitor, one resonant inductor and one auxiliary diode. The auxiliary switch creates the soft switching conditions by control of resonant elements. Besides, the auxiliary cell is not located in the main power path and cannot decrease the converter efficiency. It has simple operation modes. Besides, the proposed soft-switched converter is highly efficient while the control circuit is simple and remains …

Experimental Investigation Of The Wind Energy Harvesting Potential Of A Stand-Alone Piezoelectric Strip, Phillip Christopher Scott

Mechanical Engineering ETDs

The purpose of the study was to investigate the feasibility of harvesting wind energy on a small scale in residential areas. The method investigated was the initiation of movement-induced excitation (MIE), a type of aeroelastic flutter, within samples of polyvinylidine fluoride (PVDF), a piezoelectric polymer. Single samples of PVDF were secured in a wind tunnel and sample voltage was measured over a broad range of wind speeds. Power was calculated then via the addition of ohmic resistance matched to the magnitude of the capacitive impedances of the samples. The geometry of the PVDF samples studied was maintained as a simple …

Development Of A Reference Design For A Cyber-Physical System, Nicholas Paul Blair

Graduate Theses and Dissertations

The purpose of this thesis is to develop a reference design to assist in the selection of security practices in power electronics design. A prototype will be developed from this reference design for evaluation. This evaluation will include a brief cost/benefit analysis to gauge the efficacy of implementing each layer of security throughout the power electronics design process. This thesis will also describe the obstacles and effectiveness of integrating a Trusted Platform Module (TPM) into a cyber-hardened grid-connected device. The TPM device is a secured crypto processor that assists in generating, storing, and restricting the use of cryptographic keys. The …

Performance Analysis Of Renewable Energy Resources In Rural Areas: A Case Study Of Solar Energy, Jackson Justo

Tanzania Journal of Engineering and Technology (TJET)

This paper presents an overview of the recent development trends of solar photovoltaic (PV) systems and the performance in the Tanzanian context. The two types of solar power generation that are considered in this paper are: i) solar PV systems and ii) concentrated solar power (CSP). The two are compared in terms of cost of energy and energy storage mechanism. Moreover, the effect of ambient temperature on the solar PV module is analyzed. In addition, a detailed analysis on using solar axis tracking to increase the power generation is also presented. The extent to which the cell surface temperature and …

Modeling And Control Of Solar Pv With Battery Energy Storage For Rural Electrification, Irene Masenge

Tanzania Journal of Engineering and Technology (TJET)

In rural areas where electric power grid network is rarely available, power generation from renewable energy resource such as solar photovoltaic (PV) is mostly accomplished in standalone mode. The standalone solar PV system requires energy storage device to achieve reliable power supply to the end users. This paper presents modelling and coordination control of solar PV with battery energy storage system (BESS) for rural-electrification applications. The proposed control is accomplished via a bidirectional buck-boost converter with the objective of maintaining voltage at the DC bus constant. Simulation results based-on MATLAB/Simulink platform confirms good performance of the proposed system

Lawn Buddy, Jayson Johnston, Andrew Brown, Jacob Maljian

Electrical Engineering

Grass lawns are a common hallmark of the American home. In 2019, a survey from the National Association of Landscape Professionals found that 81% of all Americans owned a lawn [1]. Mowing is a time consuming and costly chore that is part of maintaining a grass lawn. The manual labor in mowing a lawn can exceed 40 hours per year [2]. People commonly incur weekly costs on mowing services to save time. Traditional gas powered mowers are physically demanding and use engines that need routine maintenance. They operate loudly enough that users should be wearing hearing protection and the noise …

Optimization Of Aggregated Ev Power In Residential Communities With Smart Homes, Huangjie Gong, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

Electric vehicles (EVs) tend to increase peak power for residences in the evening when house owners return home and begin charging. The aggregated EV charging demand can cause a sudden rise in the peak power at the distribution system level, resulting in a “dragon curve” Such phenomenon, combined with the “duck curve” that is caused by high photovoltaic (PV) penetration in residential communities, requires fast ramping rates and expanded capabilities for local distribution transformers and main feeder cables provided by the utility. As a solution, a residential energy storage system (RESS) can store surplus PV generation during midday and use …

Rf Power Amplifier, Angel De Jesus Delgado, Rachanon Wajanakunakorn, Andrew John Ferguson

Electrical Engineering

Wireless devices are part of everyday life, cellphones and radio receivers impact more people than any piece of technology. Thus, the respective building blocks continue to advance and achieve better performance. A primary component of all wireless communication systems is the power amplifier that drives the antenna. The Institute of Electrical and Electronics Engineers (IEEE) holds the International Microwave Symposium (IMS) every year where teams compete internationally for the most efficient RF Power Amplifier (PA). Power amplifier technologies strive to maximize efficiency and linearity. Topologies to consider are D, E, F, F-1 and Doherty since they have a maximum theoretical …

Conducted And Radiated Emi Measurements Of Parallel Buck Converters Under Varying Spread Spectrum Parameters, Elena Postupalskaya, Nathan Wang

Electrical Engineering

The Conducted and Radiated EMI Measurements with Parallel Buck Converters Under Varying Spread Spectrum Parameters research senior project aims to explore the effects from Spread Spectrum Frequency Modulation (SSFM) on the input electromagnetic interference (EMI) or noise of a switching power supply, specifically with LM53601MAEVM hardware. The input EMI is important as the main input bus needs to be clean to provide a reliable source for other sensitive devices connected to it. SSFM can replace a conventional EMI filter and save weight, space, and cost. This project provides a basis in terms of the impacts of variable SSFM in simulation …

Design And Development Of Laboratory Single-Axis Pv Module Tracker, Helen A. Rice, Delaney Berger, Avishek Maitra

Electrical Engineering

Solar energy is an integral part of the renewable energy industry. Advanced solar farms actively track solar movement and update solar panel angles to maximize the system’s output power. Cal Poly boasts its own Solar Farm that features a single-axis tracking system. Single-axis tracking aims to get panels as close to perpendicular as possible given the panel arrangements and given the time of year. Single-axis tracking is a more robust measurement and tracking option. Single-axis tracking systems usually only have East-West panel arc movement, following the sun’s rotation. Dual-axis trackers have both East-West and North-South panel arc movements. Dual-axis systems …

Efficiency Optimization Of Miso Converter, Gabriel Leonides, Christopher S. Peters, Lauren N. Rotsios

Electrical Engineering

In recent years, there has been a rapidly growing need for sustainable energy sources. This need comes from the increasing threat of climate change, significant population growth, as well as the effort to bring electricity to rural and underdeveloped areas across the world. The DC House project at Cal Poly aims to address these issues. The Multiple Input Single Output (MISO) converter is an integral part of the DC House project. The MISO converter is a system that connects multiple power sources to a DC bus. This allows the DC House to be powered by multiple types of renewable energy …

Power System Study For Oil And Gas Platform Connected To Onshore Grid, Taharim Rosshidi Hezrimi

Student Works (2020-2029)

Normally for oil and gas offshore platform, the electrical power supply is generated from the generator either using gas turbine generator, gas engine generator and diesel engine generator. The main power supply is backup by diesel engine generator in case emergency or during black start of the platform. As the design of oil and gas platform become complex, the size of generator keeps increasing. A new concept is being explored to mitigate this problem. Oil and gas company is looking to provide power generation from onshore and supplying the electrical power to a substation platform offshore and then distributed it …

A Novel Arc Welding Power Supply With Improved Power Factor Correction, Benjamin H. Tan

Master's Theses

This paper presents the design and development of a novel Arc Welding Power Supply utilizing a modified two-switch forward converter topology. The proposed design improves the power quality by improving power factor to near unity and reducing total harmonic distortion. State space analysis of the proposed circuit showed that the circuit followed a boost-buck input output relationship. Simulation of the circuit was first implemented in LTspice to verify the functionality of the new topology. Hardware implementation of the proposed design was built on a scaled-down prototype for a proof-of-concept of the new topology. The prototype specifications were created for a …

An Investigation Of Diode Failure, Nicholas James Adams

Physics

Solar electricity can be used to cheaply cook food and charge electronic devices. We investigate the viability of using diodes as heating elements for insulated solar electric cooking (ISEC). In addition, information on designing and constructing ISEC compatible phone chargers and rechargeable LED lighting systems is included.

Cybersecurity Methods For Grid-Connected Power Electronics, Stephen Joe Moquin

Graduate Theses and Dissertations

The present work shows a secure-by-design process, defense-in-depth method, and security techniques for a secure distributed energy resource. The distributed energy resource is a cybersecure, solar inverter and battery energy storage system prototype, collectively called the Cybersecure Power Router. Consideration is given to the use of the Smart Green Power Node for a foundation of the present work. Metrics for controller security are investigated to evaluate firmware security techniques. The prototype's ability to mitigate, respond to, and recover from firmware integrity degradation is examined. The prototype shows many working security techniques within the context of a grid-connected, distributed energy resource. …

A Power Constrained 433-Mhz Low Noise Amplifier, Pablo Alvarez Arellano

Graduate Theses and Dissertations

Within wireless communication systems, low noise amplifiers are critical for the performance of receivers. They are primarily responsible for providing enough gain while adding little noise to overcome the noise of the subsequent stages. The LNA presented here is part of a battery-powered transceiver meant to measure crop nutrient data and relay the information. Therefore, power consumption and area become import considerations. To design for a specific power level, a power-constrained noise optimization method is used. The method sizes the amplifying transistor for a fixed source impedance, power dissipation, technology, and operating frequency. The chosen topology is the cascode stage …

A Virtual Space Vectors Based Model Predictive Control For Three-Level Converters, Waleed Saad S. Alhosaini

Graduate Theses and Dissertations

Three-phase three-level (3-L) voltage source converters (VSC), e.g., neutral-point clamped (NPC) converters, T-type converters, etc., have been deemed to be suitable for a wide range of medium- to high-power applications in microgrids (MGs) and bulk power systems. Compared to their two-level (2-L) counterparts, adopting 3-L VSCs in the MG applications not only reduces the voltage stress across the power semiconductor devices, which allows achieving higher voltage levels, but also improves the quality of the converter output waveforms, which further leads to considerably smaller output ac passive filters.

Various control strategies have been proposed and implemented for 3-L VSCs. Among all …

High- And Low-Voltage Mitigation In Distribution Systems Using Residential Static Volt-Ampere Reactive Compensators, Andrés Valdepeña Delgado

Boise State University Theses and Dissertations

Power distribution systems are experiencing a fast transformation from simple one-way radial feeders to complex systems with multiple sources and bidirectional power flows. The rapid increase of Distributed Generation (DG) connected to the distribution system over the last decade, especially solar photovoltaic (PV), has been the key element to this transformation.

The variable nature of PV-based DG has increased the complexity of voltage regulation in distribution systems. Electric Utilities are facing an increasing number of voltage issues in distribution systems with high penetration of DGs, leading customers to experience voltage levels outside of range A of the ANSI C84.1 standard. …

Study Of A Symmetrical Llc Dual-Active Bridge Resonant Converter Topology For Battery Storage Systems, John K. George

Graduate Theses and Dissertations

A symmetrical LLC resonant converter topology with a fixed-frequency quasi-triple phase-shift modulation method is proposed for battery-powered electric traction systems with extensions to other battery storage systems. Operation of the converter with these methods yields two unique transfer characteristics and is dependent on the switching frequency. The converter exhibits several desirable features: 1) load-independent buck-boost voltage conversion when operated at the low-impedance resonant frequency, allowing for dc-link voltage regulation, zero-voltage switching across a wide load range, and intrinsic load transient resilience; 2) power flow control when operated outside the low-impedance resonance for integrated battery charging; 3) and simple operational mode …

Investigations Of New Fault-Tolerant Methods For Multilevel Inverters, Haider Mhiesan

Graduate Theses and Dissertations

The demands of power electronics with high power capability have increased in the last decades. These needs have driven the expansion of existing power electronics topologies and developing new power electronics generations. Multilevel inverters (MLI) are one of the most promising power electronics circuits that have been implemented and commercialized in high-voltage direct current (HVDC), motor drives, and battery energy storage systems (BESS). The expanding uses of the MLI have lead to creation of new topologies for different applications. However, one of the disadvantages of using MLIs is their complexity. MLIs consist of a large number of switching devices, which …

A Novel Three-Level Isolated Ac-Dc Pfc Power Converter Topology With Reduced Number Of Switches, Obaid Aldosari

Graduate Theses and Dissertations

The three-level isolated AC-DC power factor corrected (PFC) converter provides safe and more efficient power conversion. In comparison with two-level, three-level PFC converter has the advantages of low total harmonic distortion, low device voltage rating, low di/dt, better output performance, high power factor, and low switching losses at higher switching frequencies. The high frequency transformer (HFT) grants galvanic isolation, steps up or down secondary voltage, and limits damage in case of a fault current.

The existing three-level converter based on solid-state transformer (SST) topologies convert ac power from the electrical grid to a dc load while maintaining at least the …

On-Site And External Energy Harvesting In Underground Wireless, Usman Raza, Abdul Salam

Computer Information Technology Faculty Publications

Energy efficiency is vital for uninterrupted long-term operation of wireless underground communication nodes in the field of decision agriculture. In this paper, energy harvesting and wireless power transfer techniques are discussed with applications in underground wireless communications (UWC). Various external wireless power transfer techniques are explored. Moreover, key energy harvesting technologies are presented that utilize available energy sources in the field such as vibration, solar, and wind. In this regard, the Electromagnetic(EM)- and Magnetic Induction(MI)-based approaches are explained. Furthermore, the vibration-based energy harvesting models are reviewed as well. These energy harvesting approaches lead to design of an efficient wireless underground …

Dartmouth Formula Racing: Full Electric Battery System Design, Matt Gardner, Jacob Hagler, Ruthie Nordhoff, Otto Salmi

ENGS 89/90 Reports

Dartmouth Formula Racing (DFR) lacked an electrical energy storage system that was Formula Hybrid rules-compliant, optimized for FH events, safe, reliable, and integrated with the rest of their vehicle. Additionally, the team lacked the academic and professional resources required to bring a thorough, analytical approach to the design, testing, and documentation of the new storage system. Our team designed and built a Lithium-Ion battery pack (accumulator) containing energy storage, active cooling, battery management and temperature monitoring systems, and control circuitry compatible with DFR’s vehicle. Collaboration throughout design, fabrication, assembly and testing processes ensured effective knowledge transfer to the DFR team.

Neca Ghana Project, Michael T. Klee

Construction Management

Cal Poly’s motto is, “Learn by Doing" and for Cal Poly’s NECA Chapter, this isn’t simply a motto, but a directive for proactive change. For my senior project I will be leading the Cal Poly NECA chapter in the design, pre- fabrication and construction of a 5-7kw solar array, community center, ice production room and technology room in the remote fishing village of Agbokpa, Ghana. The solar array will power multiple industrial DC freezers, high efficiency LED lighting and charging stations while additionally powering water filtration and irrigation systems. Like many other fishing villages around the world, Agbokpa has no …

Residential Thermal Storage And Cooling, Joao Marcelo Rocha Belmonte, Jacob Anderson, Andrew Clarke, Daphne Forester, Bianca Hardtke, Josh Hartman, Marc D. Compere

Sustainability Conference

No abstract provided.

Dual-Axis Solar Tracker, Bryan Kennedy

All Undergraduate Projects

Renewable energies, and fuels that are not fossil fuel-based, are one of the prolific topics of debate in modern society. With climate change now becoming a primary focus for scientists and innovators of today, one of the areas for the largest amount of potential and growth is that of the capturing and utilization of Solar Energy. This method involves using a mechanical system to track the progression of the sun as it traverses the sky throughout the day. A dual-axis solar tracker such as the one designed and built for this project, can follow the sun both azimuthally and in …

Control Of Voltage-Source Converters Considering Virtual Inertia Dynamics, Tri Nguyen

College of Graduate Studies: Theses & Dissertations

Controlling power-electronic converters in power systems has significantly gained more attention due to the rapid penetration of alternative energy sources. This growth in the depth of penetration also poses a threat to the frequency stability of modern power systems. Photovoltaic and wind power systems utilizing power-electronic converters without physical rotating masses, unlike traditional power generations, provide low inertia, resulting in frequency instability. Different research has developed the control aspects of power-electronic converters, offering many control strategies for different operation modes and enhancing the inertia of converter-based systems. The precise control algorithm that can improve the inertial response of converter-based systems …

Enhanced Charge Carrier Dynamics And Defects Passivation In Hybrid Perovskite Solar Cell Using A Novel Organic Halide Salt, Md Ashuqur Rahman Laskar

Electronic Theses and Dissertations

In the last few years, active research works on hybrid perovskite solar cells (HPSCs) have been going on throughout the world as a part of clean energy revolution. HPSCs have already proved their potentiality as future solar technology through their promising photovoltaic performances and ability for low temperature based solution processing. Nevertheless, still there are remaining challenges of better charge carrier dynamics and defects minimization in HPSCs. Overcoming these challenges are very important to achieve high power conversion efficiency (PCE) practically. Aiming this, a novel organic halide salt called Phenylhydrazinium Iodide (PHAI) is introduced as additive with CH₃NH …

Optimal Sizing Of Energy Storage With Embedded Wind Power Generation, Nicholas Roche, Jane Courtney

Articles

Energy storage technologies are key to increased penetration of renewable energies on the distribution system. Not only do they increase availability of energy, but they contribute to the overall reliability of the system. However, the cost of large-scale storage systems can often be prohibitive, and storage needs to be sized appropriately, both to fill the energy gaps inevitable in renewable energies such as wind and to minimize costs. In this work, a Monte Carlo Simulation is performed to optimally size an energy storage system while minimizing overall system cost. 30 years of historical wind speed data are used to model …

Phase-Locked Loop Control In Low-Inertia Grid-Connected Voltage-Source Converters, Ifechukwude Gideon Odogwu

College of Graduate Studies: Theses & Dissertations

As the integration of renewable energy on the grid increases, the number of voltage-source converters (VSC) installed also does. VSC controls both switch turn-on and turn-off, allowing a dc voltage source to be switched between phases. For the converter to accurately synchronize with the grid, a phase-locked loop (PLL) is used for the frequency measurements of the grid. However, the implementation of PLL with measurement delay introduces harmonics, noise, high frequency, and voltage oscillation to the system due to its dynamics. The dynamics introduced to the grid can be ignored under stiff grid conditions, but power from renewable sources decreases …