Electrical and Electronics Commons^™

Electron Beam Lithography Throughput And Resolution Enhancement With Innovative Blanker Design, Junru Ruan

Legacy Theses & Dissertations (2009 - 2024)

Electron Beam Lithography (EBL) is one of the most important and most widely used methods for nano-fabrication. The primary advantage of electron beam lithography is its high resolution, and its ability to expose nanometer features without a mask. On the other hand, one of the key limitations of electron beam lithography is throughput. Slow blanking speed is one of the major bottlenecks for the system speed. In this dissertation, I will first review the prior literature of high speed blanking. Thorough theoretical and experimental studies are done on the existing designs. Physical models are built and analytical ray tracing is …

Harvesting Single Ferroelectric Domain Stressed Nanoparticles For Optical And Ferroic Applications, Gary Cook, J. L. Barnes, S. A. Basun, Dean R. Evans, Ron F. Ziolo, Arturo Ponce, Victor Yu. Reshetnyak, Anatoliy Glushchenko, Partha P. Banerjee

Electrical and Computer Engineering Faculty Publications

We describe techniques to selectively harvest single ferroelectric domain nanoparticles of BaTiO3 as small as 9 nm from a plethora of nanoparticles produced by mechanical grinding. High resolution transmission electron microscopy imaging shows the unidomain atomic structure of the nanoparticles and reveals compressive and tensile surface strains which are attributed to the preservation of ferroelectric behavior in these particles.

We demonstrate the positive benefits of using harvested nanoparticles in disparate liquid crystal systems.

Characterization Of Atmospheric Turbulence Effects Over 149 Km Propagation Path Using Multi-Wavelength Laser Beacons, Mikhail Vorontsov, Gary W. Carhart, Venkata S. Rao Gudimetla, Thomas Weyrauch, Eric Stevenson, Svetlana Lachinova, Leonid A. Beresnev, Jony Jiang Liu, Karl Rehder, Jim F. Riker

Electrical and Computer Engineering Faculty Publications

We describe preliminary results of a set of laser beam propagation experiments performed over a long (149 km) near-horizontal propagation path between Mauna Loa (Hawaii Island) and Haleakala (Island of Maui) mountains in February 2010. The distinctive feature of the experimental campaign referred to here as the Coherent Multi-Beam Atmospheric Transceiver (COMBAT) experiments is that the measurements of the atmospheric-turbulence induced laser beam intensity scintillations at the receiver telescope aperture were obtained simultaneously using three laser sources (laser beacons) with different wavelengths (λ1 = 0.53 μm, λ2 = 1.06 μm, and λ3 = 1.55 μm). The presented experimental results on …

Simulation And Optimization Of Ultra Thin Photovoltaics, Jose Luis Cruz-Campa

Open Access Theses & Dissertations

Sandia National Laboratories (SNL) conducts pioneering research and development in Micro-Electro-Mechanical Systems (MEMS) and solar cell research. This dissertation project combines these two areas to create ultra-thin small-form-factor crystalline silicon (c-Si) solar cells. These miniature solar cells create a new class of photovoltaics with potentially novel applications and benefits such as dramatic reductions in cost, weight and material usage.

At the beginning of the project, unusually low efficiencies were obtained in the research group. The intention of this research was thus to investigate the main causes of the low efficiencies through simulation, design, fabrication, and characterization.

Commercial simulation tools were …

Electromagnetic Scattering Solutions For Digital Signal Processing, Jonathan Blackledge

Other resources

Electromagnetic scattering theory is fundamental to understanding the interaction between electromagnetic waves and inhomogeneous dielectric materials. The theory unpins the engineering of electromagnetic imaging systems over a broad range of frequencies, from optics to radio and microwave imaging, for example. Developing accurate scattering models is particularly important in the field of image understanding and the interpretation of electromagnetic signals generated by scattering events. To this end there are a number of approaches that can be taken. For relatively simple geometric configurations, approximation methods are used to develop a transformation from the object plane (where scattering events take place) to the …

Design Of Acousto-Optic Chaos Based Secure Free-Space Optical Communication Links, Anjan K. Ghosh, Pramode K. Verma, Samuel Cheng, Robert C. Huck, Monish Ranjan Chatterjee, Mohammed A. Al-Saedi

Electrical and Computer Engineering Faculty Publications

We discuss the design of an acousto-optic cell based free space optical communication link where the data beam is made secure through chaos encryption. Using external signal modulation of the diffracted light from a hybrid acousto-optic cell chaos (or directly via incorporation in the sound-cell driver's bias voltage) encryption of data is possible. We have shown numerically that decryption of the encoded data is possible by using an identical acousto-optic system in the receiver.

Analysis Of Partial Discharge Pulse Height Distribution Parameters, Vinay N. Nimbole

Electrical & Computer Engineering Theses & Dissertations

Partial Discharges (PD) have been traditionally used to assess the state of any insulation system and its remnant life. In earlier work, Perspex (PMMA) samples with a needle plane gap have been aged with AC voltage. Their tree growth was monitored simultaneously by collecting PD at regular intervals of time and taking microphotographs in real time without interrupting the aging voltage. The obtained partial discharge pulse amplitude records were clustered together into groups of class intervals. The sequence of PD pulse height records was quantified as a time series of shape (η), and scale (σ) parameters of a Weibull distribution. …

Object Trajectory Estimation Using Optical Flow, Shuo Liu

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Object trajectory tracking is an important topic in many different areas. It is widely used in robot technology, traffic, movie industry, and others. Optical flow is a useful method in the object tracking branch and it can calculate the motion of each pixel between two frames, and thus it provides a possible way to get the trajectory of objects. There are numerous papers describing the implementation of optical flow. Some results are acceptable, but in many projects, there are limitations. In most previous applications, because the camera is usually static, it is easy to apply optical flow to identify the …

Electron Multipactor: Theory Review, Comparison And Modeling Of Mitigation Techniques In Icepic, Neil G. Rogers

Theses and Dissertations

Mitigation approaches for single surface multipactor at dielectric windows are investigated using Particle-In-Cell (PIC) simulations. Initially baseline susceptibility diagrams are constructed analytically and compared with self-consistent, dynamic system trajectories. The power deposited on the surface of a dielectric window in an HPM system is considered using three different methods and the results of PIC simulations. Geometric mitigation is then considered by varying the window orientation with respect to the HPM electric held. Small angular deviations, less than 20 degrees, from the nominal case of normal incidence show dramatic changes in the susceptibility diagram. A materials approach to mitigation is then …

Tilted Parallel Dielectric Slab As A Multilevel Attenuator For Incident P- Or S-Polarized Light, R. M.A. Azzam

Electrical Engineering Faculty Publications

Under the condition of first-order blooming, a parallel dielectric slab, which is inserted in the path of an obliquely incident p- or s-polarized light beam, introduces multiple discrete attenuation levels given by 1/3, 4/27, 4/243,...... in reflection and 4/9, 4/81, 4/729,...... in transmission. These attenuation levels are independent of the slab refractive index, incident p or s linear polarization, or the presence of identical transparent surface coatings at the front and back sides of the slab. Therefore, the tilted slab provides multidecade reflectance and attenuation reference values that can be used in calibrating spectrophotometers and filters, and also …

Monoclinic Optical Constants, Birefringence, And Dichroism Of Slanted Titanium Nanocolumns Determined By Generalized Ellipsometry, Daniel Schmidt, Benjamin Booso, Tino Hofmann, Eva Schubert, Andrew Sarangan, Mathias Schubert

Electrical and Computer Engineering Faculty Publications

Generalized spectroscopic ellipsometry determines the principal monoclinic optical constants of thin films consisting of slanted titanium nanocolumns deposited by glancing angle deposition under 85° incidence and tilted from the surface normal by 47°. Form birefringence measured for wavelengths from 500 to 1000 nm renders the Ti nanocolumns monoclinic absorbing crystals with c-axis along the nanocolumns, b-axis parallel to the film interface, and 67.5° monoclinic angle between the aand c-axes. The columnar thin film reveals anomalous optical dispersion, extreme birefringence, strong dichroism, and differs completely from bulk titanium. Characteristic bulk interband transitions are absent in the spectral range investigated.

Sub-Circuit Selection And Replacement Algorithms Modeled As Term Rewriting Systems, Eric D. Simonaire

Theses and Dissertations

Intent protection is a model of software obfuscation which, among other criteria, prevents an adversary from understanding the program’s function for use with contextual information. Relating this framework for obfuscation to malware detection, if a malware detector can perfectly normalize a program P and any obfuscation (variant) of the program O(P), the program is not intent protected. The problem of intent protection on programs can also be modeled as intent protection on combinational logic circuits. If a malware detector can perfectly normalize a circuit C and any obfuscation (variant) O(C) of the circuit, the circuit is not intent protected. In …

A C To Register Transfer Level Algorithm Using Structured Circuit Templates: A Case Study With Simulated Annealing, Jonathan D. Phillips

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

A tool flow is presented for deriving simulated annealing accelerator circuits on a field programmable gate array (FPGA) from C source code by exploring architecture solutions that conform to a preset template through scheduling and mapping algorithms. A case study carried out on simulated annealing-based Autonomous Mission Planning and Scheduling (AMPS) software used for autonomous spacecraft systems is explained. The goal of the research is an automated method for the derivation of a hardware design that maximizes performance while minimizing the FPGA footprint. Results obtained are compared with a peer C to register transfer level (RTL) logic tool, a state-of-the-art …

Plurality Of Principal Angles For A Given Pseudo-Brewster Angle When Polarized Light Is Reflected At A Dielectric-Conductor Interface, R. M.A. Azzam, A. Alsamman

Electrical Engineering Faculty Publications

The pseudo-Brewster angle ϕpB of minimum reflectance for p-polarized light and the principal angle ϕ¯ at which incident linearly polarized light of the proper azimuth is reflected circularly polarized are considered as functions of the complex relative dielectric function ε of a dielectric–conductor interface over the entire complex ε plane. In particular, the spread of ϕ¯for a given ϕpB is determined, and the maximum difference (ϕ¯−ϕpB)max is obtained as a function of ϕpB . The maximum difference (ϕ¯−ϕpB)max approaches 45° and 0 in the limit as ϕpB→0 and 90°, respectively. ForϕpB<22.666° , multiple principal angles ϕ¯i , i=1,2,3 , appear for each ε in a subdomain of fractional optical constants. …

Hand-Held Flyback Driven Coaxial Dielectric Barrier Discharge: Development And Characterization, Victor J. Law, Vladimir Milosavljevic, Neil O’Connor, James F. Lalor, Steven Daniels

Articles

The development of a handheld single and triple chamber atmospheric pressure coaxial dielectric barrier discharge driven by Flyback circuitry for helium and argon discharges is described. The Flyback uses external metal-oxide-semiconductor field-effect transistor power switching technology and the transformer operates in the continuous current mode to convert a continuous dc power of 10–33 W to generate a 1.2–1.6 kV 3.5 μs pulse. An argon discharge breakdown voltage of ∼768 V is measured. With a 50 kHz, pulse repetition rate and an argon flow rate of 0.5–10 argon slm (slm denotes standard liters per minute), the electrical power density deposited in …

Inhibition Of Linear Absorption In Opaque Materials Using Phase-Locked Harmonic Generation, Marco Centini, Vito Roppo, Eugenio Fazio, Federico Pettazzi, Concita Sibilia, Joseph W. Haus, John V. Foreman, Neset Akozbek, Mark J. Bloemer, Michael Scalora

Electrical and Computer Engineering Faculty Publications

We theoretically predict and experimentally demonstrate inhibition of linear absorption for phase and group velocity mismatched second- and third-harmonic generation in strongly absorbing materials, GaAs, in particular, at frequencies above the absorption edge.

A 100-fs pump pulse tuned to 1300 nm generates 650 and 435 nm second- and third-harmonic pulses that propagate across a 450−μm-thick GaAs substrate without being absorbed.

We attribute this to a phase-locking mechanism that causes the pump to trap the harmonics and to impress on them its dispersive properties.

Material Perturbations To Enhance Performance Of The Theile Half-Width Leaky Mode Antenna, Jason A. Girard

Theses and Dissertations

Microstrip traveling-wave antennas, often referred to as leaky-wave antennas, have been shown to radiate when the dominant or fundamental mode is suppressed and the first higher-order mode is excited. One such microstrip variation is the Thiele Half-Width (THW) antenna, which operates from 5.9 - 8.2 GHz for this research. Increasing the bandwidth over which the THW antenna radiates is desired, as is a fundamental understanding of the propagation characteristics over this region. This dissertation seeks to vary or perturb the material and physical properties of the THW antenna, including strip-width variations and modifications of the substrate layer, to achieve these …

A Timer Module For An 8051 Microcontroller, Troy England

Electrical Engineering Undergraduate Honors Theses

A timer module for an 8051 Microcontroller is designed from the ground up. It could potentially be integrated into a larger 8051 for use in lunar and Martian missions. It follows through a synchronous digital design flow from HDL code through layout verification. The timer shows functionality at 100MHz with some minor glitches.

Algorithm Development Of The Aglite-Lidar Instrument, Christian Marchant

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Particulate emissions from agricultural operations are increasingly receiving attention from regulatory bodies as a potential source of air pollution. The Space Dynamics Laboratory (SDL) has developed the Aglite system, a suite of instruments including a lidar that is capable of measuring particulate emission levels from agricultural facilities. This system provides a novel method of measuring particulate mass (PM) pollution, allowing measurements to be taken of diverse types of facilities with high temporal and spatial resolution. This high resolution allows for the measurement of emission levels generated by specific activities, fostering the development and determination of best management practices.

The Aglite …

Algorithm Development For Column Water Vapor Retrieval Using The Sun And Aureole Measurement (Sam) Sensor, Joshua Bruce Williams

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

To understand and model the energetics of the Sun-Earth connection, measurements of specific atmospheric molecules are beneficial. The objective is to formulate an algorithm to derive temporally varying atmospheric water vapor concentrations as functions of altitude, latitude, and longitude from solar irradiance absorption measurements. The Visidyne SAM (Sun and Aureole Measurement) instrument, which studies the size and distribution of cloud particles, was used to obtain the experimental data. By introducing a spectrometer to the SAM instrument, column water vapor is produced as part of the data product. A new model optimized algorithm is developed and tested versus existing algorithms. Through …

Real-Time Plasma Controlled Chemistry In A Two-Frequency, Confined Plasma Etcher, Vladimir Milosavljevic, Albert R. Ellingboe, Cezar Gaman, John V. Ringwood

Articles

The physics issues of developing model-based control of plasma etching are presented. A novel methodology for incorporating real-time model-based control of plasma processing systems is developed. The methodology is developed for control of two dependent variables (ion flux and chemical densities) by two independent controls (27 MHz power and O2flow). A phenomenological physics model of the nonlinear coupling between the independent controls and the dependent variables of the plasma is presented. By using a design of experiment, the functional dependencies of the response surface are determined. In conjunction with the physical model, the dependencies are used to deconvolve the sensor …

Modeling And Characterization Of Adaptive Lanthanum-Modified Lead Zirconate Titanate (Plzt) Microlenses, Yasser A. Abdelaziez, Partha P. Banerjee

Electrical and Computer Engineering Faculty Publications

We report the modeling and characterization of adaptive voltage controlled electro-optic microlenses. First, we utilize finite element analysis (FEA) to simulate the induced electro-optic effect in lanthanum-modified lead zirconate titanate (PLZT). FEA simulation provides microlens parameters such as phase and focal length. A simple z-scan method is developed to fully characterize the adaptive voltage controlled linear lens. Experimental z-scan results are shown to match the theoretical predictions from FEA.

Efficiency Of Linear-To-Circular Polarization Conversion For Light Reflection At The Principal Angle By A Dielectric-Conductor Interface, R. M.A. Azzam, A. Alsamman

Electrical Engineering Faculty Publications

The efficiency ηLC of linear-to-circular polarization conversion when light is reflected at a dielectric–conductor interface is determined as a function of the principal angle ϕ¯ and principal azimuth ψ¯ . Constant- ηLC contours are presented in the ϕ¯ ,ψ¯ plane for values of ηLC from 0.5 to 1.0 in steps of 0.05, and the corresponding contours in the complex plane of the relative dielectric function ϵ are also determined. As specific examples, efficiencies ⩾88% are obtained for light reflection by a Ag mirror in the visible and near-IR (400–1200nm) spectral range, and ≥40% for the reflection of extreme ultraviolet (EUV) …

Tailoring Metallodielectric Structures For Superresolution And Superguiding Applications In The Visible And Near-Ir Ranges, Domenico De Ceglia, Maria Antonietta Vincenti, M. G. Cappeddu, Marco Centini, Neset Akozbek, Antonella D'Orazio, Joseph W. Haus, Mark J. Bloemer, Michael Scalora

Electrical and Computer Engineering Faculty Publications

We discuss propagation effects in realistic, transparent, metallodielectric photonic band gap structures in the context of negative refraction and super-resolution in the visible and near infrared ranges. In the resonance tunneling regime, we find that for transverse-magnetic incident polarization, field localization effects contribute to a waveguiding phenomenon that makes it possible for the light to remain confined within a small fraction of a wavelength, without any transverse boundaries, due to the suppression of diffraction. This effect is related to negative refraction of the Poynting vector inside each metal layer, balanced by normal refraction inside the adjacent dielectric layer: The degree …

Electrically Steerable Diffraction Gratings For Hyperspectral Imaging: A Microelectromechanical System Design And Fabrication, Saban Atinc Delican

Theses and Dissertations

The current research is focused on the design and fabrication of an electrically programmable diffraction grating using standard micro electro mechanical systems (MEMS) technology. The goal is to design a beam steering element required to build very small hyperspectral imaging (HSI) sensors. The diffraction grating will be used to perform beam-dispersion - a critical step in the imaging process. The proposed transmissive diffraction grating based approach will minimize the overall size and the number of components in the physical design of the hyperspectral imagers, thereby enabling us to exploit the traditional advantages of MEMS such as increased reliability, smaller size, …

Color Filter Array Image Analysis For Joint Denoising And Demosaicking, Keigo Hirakawa

Electrical and Computer Engineering Faculty Publications

Noise is among the worst artifacts that affect the perceptual quality of the output from a digital camera. While cost-effective and popular, single-sensor solutions to camera architectures are not adept at noise suppression. In this scheme, data are typically obtained via a spatial subsampling procedure implemented as a color filter array (CFA), a physical construction whereby each pixel location measures the intensity of the light corresponding to only a single color. Aside from undersampling, observations made under noisy conditions typically deteriorate the estimates of the full-color image in the reconstruction process commonly referred to as demosaicking or CFA interpolation in …

Performance Comparison Of Pb(Zr0.52Ti0.48)O3-Only And Pb(Zr0.52Ti0.48)O3-On-Silicon Resonators, Hengky Chandrahalim, Sunil A. Bhave, Ronald G. Polcawich, Jeff Pulskamp, Dan Judy, Roger Kaul, Madan Dubey

Faculty Publications

This paper provides a quantitative comparison and explores the design space of lead zirconium titanate (PZT)–only and PZT-on-silicon length-extensional mode resonators for incorporation into radio frequency microelectromechanical system filters and oscillators. We experimentally measured the correlation of motional impedance (R_X) and quality factor (Q) with the resonators’ silicon layer thickness (t_Si). For identical lateral dimensions and PZT-layer thicknesses (t_PZT), the PZT-on-silicon resonator has higher resonant frequency (f_C), higher Q (5100 versus 140), lower R_X (51 Ω versus 205 Ω), and better linearity [third-order input intercept …

Management Framework For Hybrid Wireless Networks, Chong Shen

Theses

The objective of the Hybrid Wireless Network with dedicated Relay Nodes (HWN*) architecture is to interface the Base Station (BS) Oriented Mobile Network (BSON) and the 802.fix based Mobile Ad hoc Wireless Network (MANET) so that one system can be utilised as an alternative radio access network for data transmissions, while the incorporation of Relay Nodes (RN) is to extend the communication coverage, optimise medium resource sharing, increase spatial reuse opportunity, stabilise MANET link and create more micro-cells. The HWN* keeps the existing cellular infrastructure and a Mobile Terminal (MT) can borrow radio resources from other cells via secure multi-hop …

Elliptic Curve Cryptography Security On Restricted Mobile Devices, Debbie Mccann

Theses

Mobile technologies with limited resources, such as smart phones or PDAs, have increased dramatically in popularity. However, the level of security provided for these technologies has not kept pace with the value of the data that they contain or transmit.

Wireless networks usually provide some security, in the form of encryption. GSM and GPRS use different forms of the A5 algorithm, and Wi-Fi uses WEP or WPA. These encryption algorithms have proven weaknesses and in some cases have been efficiently cracked. To improve the security of wireless networks, stronger encryption algorithms need to be developed. One of the most attractive …

A Distributed Ai Approach For Large-Scale Wlan Design, Alan Mcgibney

Theses

The recent dramatic trend towards always-on-connectivity has driven the need for mobile ubiquitous computing environments with the advent of the Wireless Local Area Network (WLAN) seeing a shift from traditional wired networks to wireless networking. A WLAN typically contains a number of access points that allow wireless enabled clients access information and network resources such as the internet without the need for wires, offering flexibility and mobility to the users. Initial wireless networks were convenience based allowing users access to the primary wired network, and involved little planning prior to roll-out. The proliferation of low cost wireless devices combined wdth …