Electrical and Electronics Commons^™

Study Of Soliton Stabilization In D+1 Dimensions Using Novel Analytical And Numerical Techniques, George Nehmetallah, Partha P. Banerjee

Electrical and Computer Engineering Faculty Publications

In this Chapter, we provide a brief review of the underlying nonlinear Schrödinger and associated equations that model spatio-temporal propagation in one and higher dimensions in a nonlinear dispersive environment. Particular attention is given to fast adaptive numerical techniques to solve such equations, and in the presence of dispersion and nonlinearity management, saturating nonlinearity and nonparaxiality. A unique variational approach is also outlined which helps in determining the ranges of nonlinearity and dispersion parameters to ensure stable solutions of the nonlinear equations. The propagation of 3+1 dimensional spatio-temporal pulses, or optical bullets is also modeled using a fast adaptive split-step …

Atmospheric Turbulence Compensation Of Point Source Images Using Asynchronous Stochastic Parallel Gradient Descent Technique On Amos 3.6 M Telescope, Mikhail Vorontsov, Jim F. Riker, Gary W. Carhart, Venkata S. Rao Gudimetla, Leonid A. Beresnev, Thomas Weyrauch

Electrical and Computer Engineering Faculty Publications

The Stochastic Parallel Gradient Descent Technique-based Adaptive Optics (SPGD-AO) system described in this presentation does not use a conventional wavefront sensor. It uses a metric signal collected by a single pixel detector placed behind a pinhole in the image plane to drive three deformable mirrors (DMs). The system is designed to compensate the image for turbulence effects. The theory behind this method is described in detail in [1]. However this technique, while widely simulated and tested in the laboratory, was not yet verified in astronomical field site experiments. During the month of May 2007, a series of experiments with SPGD-AO …

Adaptive Optics Performance Over Long Horizontal Paths: Aperture Effects In Multi-Conjugate Adaptive Optical Systems, Miao Yu, Mikhail Vorontsov, Svetlana Lachinova, Jim F. Riker, Venkata S. Rao Gudimetla

Electrical and Computer Engineering Faculty Publications

We analyze various scenarios of the aperture effects in adaptive optical receiver-type systems when inhomogeneities of the wave propagation medium are distributed over long horizontal propagation path, or localized in a few thin layers remotely located from the receiver telescope pupil. Phase aberration compensation is performed using closed-loop control architectures based on phase conjugation and decoupled stochastic parallel gradient descent (DSPGD) control algorithms. Both receiver system aperture diffraction effects and the impact of wave-front corrector position on phase aberration compensation efficiency are analyzed for adaptive systems with single or multiple wave-front correctors.

Investigation Of Negative Refractive Index In Reciprocal Chiral Materials, Monish Ranjan Chatterjee, Partha P. Banerjee, Pradeep R. Anugula

Electrical and Computer Engineering Faculty Publications

It is well known that there exist both natural materials (such as milk or sugar solution) possessing chiral (or handed) properties, as well as an increasing list of man-made materials (such as sodium bromate) that exhibit chirality. One of the principal properties of chirality is that light of any arbitrary polarization, when propagating through a chiral material, splits up into two circular polarizations propagating in different directions. In the past decade or longer, researchers have investigated electromagnetic transverse (plane) wave propagation across a non-chiral/chiral interface, and determined the electromagnetic Fresnel coefficients for such propagation. Traditionally, such coefficients are derived under …

Phase Shifts In Frustrated Total Internal Reflection And Optical Tunneling By An Embedded Low-Index Thin Film, R. M.A. Azzam

Electrical Engineering Faculty Publications

Simple and explicit expressions for the phase shifts that p- and s-polarized light experience in frustrated total internal reflection (FTIR) and optical tunneling by an embedded low-index thin film are obtained. The differential phase shifts in reflection and transmission Δr,Δt are found to be identical, and the associated ellipsometric parameters ψr,ψt are governed by a simple relation, independent of film thickness. When the Fresnel interface reflection phase shifts for the pand s polarizations or their average are quarter-wave, the corresponding overall reflection phase shifts introduced by the embedded layer are also quarter-wave for all values of film …

Multi-Dimensional Wave Front Sensing Algorithms For Embedded Tracking And Adaptive Optics Applications, Christopher C. Wood

Theses and Dissertations

Current tracking and adaptive optics techniques cannot compensate for fast-moving extended objects, which is important for ground-based telescopes providing space situational awareness. To fill this need, a vector-projection maximum-likelihood wave-front sensing algorithm development and testing follows for this application. A derivation and simplification of the Cramer-Rao Lower Bound for wavefront sensing using a laser guide star bounds the performance of these systems and guides implementation of a vastly optimized maximum-likelihood search algorithm. A complete analysis of the bias, mean square error, and variance of the algorithm demonstrates exceptional performance of the new sensor. A proof of concept implementation shows feasibility …

Lqg/Ltr Tilt And Tip Control For The Starfire Optical Range 3.5-Meter Telescope's Adaptive Optics System, Neil D. Paris

Theses and Dissertations

The Air Force Research Laboratory has sponsored research on the tracking control loop portion of the adaptive optics system in the Starfire Optical Range 3.5-meter telescope at Kirtland Air Force Base. The control loop includes two steering mirrors (Coarse Steering Mirror and Fine Steering Mirror) used to remove wavefront tilt and tip phase distortion from light entering the telescope. The objective of this research is to design a single Linear Quadratic Gaussian controller to control both steering mirrors in order to eliminate wavefront tilt and tip distortions induced by the earth's atmosphere, and to evaluate the stability robustness and performance …

Pocket Deformable Mirror For Adaptive Optics Applications, Leonid A. Beresnev, Mikhail Vorontsov, Peter Wangsness

Electrical and Computer Engineering Faculty Publications

Adaptive/active optical elements are designed to improve optical system performance in the presence of phase aberrations. For atmospheric optics and astronomical applications, an ideal deformable mirror should have sufficient frequency bandwidth for compensation of fast changing wave front aberrations induced by either atmospheric turbulences or by turbulent air flows surrounding a flying object (air optical effects). In many applications, such as atmospheric target tracking, remote sensing from flying aircraft, boundary layer imaging, laser communication and laser beam projection over near horizontal propagation paths the phase aberration frequency bandwidth can exceed several kHz. These fast-changing aberrations are currently compensated using relatively …

Adaptive Beam Director For A Tiled Fiber Array, Mikhail Vorontsov, Jim F. Riker, Ernst Polnau, Svetlana Lachinova, Venkata S. Rao Gudimetla

Electrical and Computer Engineering Faculty Publications

We present the concept development of a novel atmospheric compensation system based on adaptive tiled fiber array architecture operating with target-in-the-loop scenarios for directed beam applications. The adaptive tiled fiber array system is integrated with adaptive beam director (ABD). Wavefront control and sensing functions are performed directly on the beam director telescope primary mirror. The beam control of the adaptive tiled fiber array aims to compensate atmospheric turbulence-induced dynamic phase aberrations and results in a corresponding brightness increase on the illuminated extended object. The system is specifically designed for tiled fiber system architectures operating in strong intensity scintillation and speckle-modulation …

Terahertz Studies Of The Dielectric Response And Second-Order Phonons In A Gase Crystal, B. L. Yu, F. Zeng, V. Kartazayev, R. R. Alfano, K. C. Mandal

Faculty Publications

No abstract provided.

Signal Flow Analysis, Partha P. Banerjee

Electrical and Computer Engineering Faculty Publications

Signal flow graphs are a viable alternative to block diagrammatic representation of a system. What makes signal flow graphs attractive is that certain features from graph theory can be applied to the simplification and the synthesis of complex systems.

Functional Nanoparticles In Thin Films As Sensing Media, Elena A. Guliants, Ryan Schwarb, Hope Bearbower, James R. Gord, Christopher E. Bunker

Electrical and Computer Engineering Faculty Publications

The combination of unique properties offered by materials on the nanoscale with the increased role of surface chemistry in nanostructured solids makes core-shell nanoparticles extremely attractive for application to "smart" thin-film coatings. Sensing properties of nanoparticle-based thin films were studied in several systems containing organic-coated semiconductor and metallic particles. In semiconductors, the interaction of organic shell and/or thin-film "matrix" with the environment results in changes in the nanoparticle's surface states, altering the optical properties of the thin film. Measuring the electrical properties of thin films composed of metallic cores with hydrocarbon shells offers another mechanism to monitor the local environment …

Achromatic Angle-Insensitive Infrared Quarter-Wave Retarder Based On Total Internal Reflection At The Si–Sio2 Interface, R. M.A. Azzam, Cristina L. Spinu

Electrical Engineering Faculty Publications

An achromatic infrared (λ = 1.2–4 μm), Si-prism quarter-wave retarder (QWR) is described that uses total internal reflection at a buried Si–SiO₂ interface at an angle of incidence φ near 33°, where ∂Δ/∂φ = 0. The retardance Δ deviates from 90° by <±2° within a field of view of ±10° (in air) over the entire bandwidth. Because the SiO₂ layer at the base of the prism is optically thick, this QWR is unaffected by environmental contamination.

Volume Holographic Recording And Readout For 90-Deg Geometry, Partha P. Banerjee, Monish Ranjan Chatterjee, Nickolai Kukhtarev, Tatiana Kukhtareva

Electrical and Computer Engineering Faculty Publications

When a prerecorded cross-beam hologram is reconstructed (so-called edge-lit readout) with a uniform plane wave and a point source, the resulting exact solutions reveal Bessel-function-type diffracted beam profiles, which are fundamentally modified under weak propagational diffraction. The case of a profiled beam readout with propagational diffraction may be analyzed using a transfer function approach based on 2-D Laplace transforms. In a second series of investigations, dynamic readout from a cross-beam volume hologram recorded with two orthogonal uniform plane waves is considered for various dependences of the refractive index modulation with intensity. Typically, refractive index profiles that are proportional to the …

Volume Holographic Optical Elements, Ching-Cherng Sun, Partha P. Banerjee

Electrical and Computer Engineering Faculty Publications

The final two papers are concerned with the analysis of novel holograms. Banerjee et al. investigate holographic recording and reconstruction for edge-lit holograms recorded in a 90-degree geometry. Various cases of recording and readout that incorporate propagational diffraction have been modeled. It is shown that the 90-degree geometry can result in beam shaping, as evidenced through preliminary experimental results with photorefractive lithium niobate. Nguyen et al. propose a new approach for designing computer-generated holograms. An artificial neural network is used to initiate the genetic algorithm so that the high computation cost of genetic algorithms for synthesizing holograms is significantly reduced …

Phase Shifts That Accompany Total Internal Reflection At A Dielectric–Dielectric Interface, R. M.A. Azzam

Electrical Engineering Faculty Publications

The absolute, average, and differential phase shifts that p- and s-polarized light experience in total internal reflection (TIR) at the planar interface between two transparent media are considered as functions of the angle of incidence φ. Special angles at which quarter-wave phase shifts are achieved are determined as functions of the relative refractive index N. When the average phase shift equals π/2, the differential reflection phase shift Δ is maximum, and the reflection Jones matrix assumes a simple form. For N>√3, the average and differential phase shifts are equal (hence δ_p=3δ_s) at …

Are Microbubbles Necessary For The Breakdown Of Liquid Water Subjected To A Submicrosecond Pulse?, R. P. Joshi, J. Qian, G. Zhao, J. Kolb, K. H. Schoenbach, E. Schamiloglu, J. Gaudet

Electrical & Computer Engineering Faculty Publications

Electrical breakdown in homogeneous liquid water for an ∼ 100 ns voltage pulse is analyzed. It is shown that electron-impact ionization is not likely to be important and could only be operative for low-density situations or possibly under optical excitation. Simulation results also indicate that field ionization of liquid water can lead to a liquid breakdown provided the ionization energies were very low in the order of 2.3eV. Under such conditions, an electric-field collapse at the anode and plasma propagation toward the cathode, with minimal physical charge transport, is predicted. However, the low, unphysical ionization energies necessary for matching …

Examination Of Focused Beam Propagation Through A Finite Non-Reciprocal Planar Chiral Slab Using Complex Fresnel Coefficients And Dual Transforms, Monish Ranjan Chatterjee, Sumit Nema, Partha P. Banerjee

Electrical and Computer Engineering Faculty Publications

Recently, uniform plane wave propagation across a nonchiral-chiral interface was examined via the development of appropriate Fresnel coefficients. In this extension, propagation of focused uniform and profiled beams through a finite, planar nonreciprocal chiral slab is investigated using complex Fresnel coefficients via angular plane wave decomposition and dual transforms.

Revisiting The Fresnel Coefficients For Uniform Plane Wave Propagation Across A Nonchiral, Reciprocal And Chiral, Nonreciprocal Interface, Monish Ranjan Chatterjee, Sumit Nema

Electrical and Computer Engineering Faculty Publications

The problem of EM wave propagation in non-reciprocal chiral media has been studied by several investigators. In a recent approach, a dual-transform technique has been developed to study the problem of such propagation under paraxial and slow-envelope variation conditions.

In this paper, we first outline some of the results obtained using the dual transform technique for arbitrary boundary conditions within the left boundary of a semi-infinite, non-reciprocal chiral medium for a uniform plane wave, and a fundamental Gaussian-profiled beam. Next, we explore the problem of a uniform EM wave incident at an oblique angle at an interface between a reciprocal, …

Optimal Beam Splitters For The Division-Of-Amplitude Photopolarimeter, R. M.A. Azzam, A. De

Electrical Engineering Faculty Publications

Optimal optical parameters of the beam splitter that is used in the division-of-amplitude photopolarimeter are determined. These are (1) 50%–50% split ratio of the all-dielectric beam splitter, (2) differential phase shifts in reflection and transmission Δ_r and Δ_t that differ by ±π/2, and (3) ellipsometric parameters (ψ_r, ψ_t)= (27.368°, 62.632°) or (62.632°, 27.368°). It is also shown that for any nonabsorbing beam splitter that splits incident unpolarized light equally, the relationship ψ_r+ψ_t=π/2 is always satisfied.

Implementation Of A Si/Sic Hybrid Optically Controlled High-Power Switching Device, Prashant Bhadri, Kuntao Ye, Elena A. Guliants, Fred R. Beyette Jr.

Electrical and Computer Engineering Faculty Publications

The ever-increasing performance and economy of operation requirements placed on commercial and military transport aircraft are resulting in very complex systems. As a result, the use of fiber optic component technology has lead to high data throughput, immunity to EMI, reduced certification and maintenance costs and reduced weight features. In particular, in avionic systems, data integrity and high data rates are necessary for stable flight control. Fly-by-Light systems that use optical signals to actuate the flight control surfaces of an aircraft have been suggested as a solution to the EMI problem in avionic systems. Current fly-by-light systems are limited by …

Translation Of 'Balika Badhu: A Selected Anthology Of Bengali Short Stories', Monish Ranjan Chatterjee

Electrical and Computer Engineering Faculty Publications

This project, which began with the desire to render into English a rather long tale by Bimal Kar about five years ago, eventually grew into a considerably more extended compilation of Bengali short stories by 10 of the most well-known practitioners of that art since the heyday of Rabindranath Tagore. The collection is limited in many ways, not the least of which being that no woman writer has been included, and that it contains only a baker's dozen stories (if we count Bonophool's micro-stories collectively as one ) — a number pitifully small considering the vast and prolific field of …

A 0.5 Μm Thick Polysilicon Schottky Diode With Rectification Ratio Of 10^6, Elena A. Guliants, Chunhai Ji, Young J. Song, Wayne A. Anderson

Electrical and Computer Engineering Faculty Publications

Polycrystalline Si films, 0.5-mm thick, were obtained as a result of metal-induced growth by sputtering from a Si target on 25 nm thick Ni prelayers at 525 °C. Silicon grew heteroepitaxially on the NiSi2 layer formed due to the reaction between the sputtered Si atoms and Ni. Schottky diodes were fabricated on the Si films by deposition of a Schottky metal on the front surface of the film while Ni disilicide provided an intimate ohmic contact at the back. A Pd/n-Si diode using an n-Si film annealed for 2 h at 700 °C in forming gas demonstrated a rectification ratio …

Self-Assembly Of Spatially Separated Silicon Structures By Si Heteroepitaxy On Ni Disilicide, Elena A. Guliants, Chunhai Ji, Wayne A. Anderson

Electrical and Computer Engineering Faculty Publications

A nonlithographic approach to produce self-assembled spatially separated Si structures for nanoelectronic applications was developed, employing the metal-induced silicon growth. Densely packed Si whiskers, 500–800 nm thick and up to 2500 nm long, were obtained by magnetron sputtering of Si on a 25 nm thick Ni prelayer at 575 °C. The nucleation of the NiSi2 compound at the Ni–Si interface followed by the Si heteroepitaxy on the lattice-matched NiSi2 is suggested to be the driving force for the whisker formation.

Angular Range For Reflection Of P-Polarized Light At The Surface Of An Absorbing Medium With Reflectance Below That At Normal Incidence, R. M.A. Azzam, Ericson E. Ugbo

Electrical Engineering Faculty Publications

The range of incidence angle, 0 < φ < φ_e, over which p-polarized light is reflected at interfaces between transparent and absorbing media with reflectance below that at normal incidence is determined. Contours of constant φ_e in the complex plane of the relative dielectric constant ε are presented. A method for determining the real and imaginary parts of the complex refractive index, ε^1/2 = n + jk, which is based on measuring φ_e and the pseudo-Brewster angle φ_pB, is viable in the domain of fractional optical constants, n, k < 1.

Feedback Correction Of Angular Error In Grating Readout, Monish Ranjan Chatterjee, Sundaram Ramachandran

Electrical and Computer Engineering Faculty Publications

Angular and wavelength READ beam errors in holographic interconnection systems are often a recurrent problem. Several strategies have been proposed to minimize or eliminate such READOUT misalignments.

Some years ago, Chatterjee and co-workers proposed a method involving READ beam wavelength tuning to correct output angular errors. In this paper, we investigate the possibility of using an acousto-optic (A-O) Bragg cell with optoelectronic feedback to dynamically correct the scattered beam for deviations in the incidence direction of the READ beam of a hologram. The concept here is based on an acoustic frequency feedback strategy used recently by Balakshy and Kazaryan for …

Overview Of Acousto-Optic Bistability, Chaos, And Logical Applications, Monish Ranjan Chatterjee, Erol Sonmez

Electrical and Computer Engineering Faculty Publications

An overview is presented of the key results in the field of acousto-optic bistability in the past two decades. It is shown that the basic acousto-optic bistable device may be described as a nonlinear dynamical system which satisfies a quadratic map. Thereafter, details are presented of several analytical methods, computer modeling approaches, including the SPICE circuit modeling technique, and experiments that have been used to understand the phenomenon.

Extensions to logical and digital applications are also discussed.

Tilted Bilayer Membranes As Simple Transmission Quarter-Wave Retardation Plates, R. M.A. Azzam, Fadi A. Mahmoud

Electrical Engineering Faculty Publications

A tilted bilayer membrane, which consists of two thin films of transparent optically isotropic materials of different refractive indices, can function as a transmission quarter-wave retarder (QWR) at a high angle of incidence. A specific design using a cryolite-Si membrane in the infrared is presented, and its tolerances to small shifts of wavelength, incidence angle, and film thickness errors are discussed. Some designs provide a dual QWR in transmission and reflection. Such devices provide simple linear-to-circular (and circular-to-linear) polarization transformers. Bilayer eighth-wave retarders without diattenuation are also introduced.

Study Of Dynamics And Mechanism Of Metal-Induced Silicon Growth, Elena A. Guliants, Wayne A. Anderson

Electrical and Computer Engineering Faculty Publications

The present study addresses the mechanism of metal-induced growth of device-quality silicon thin films. Si deposition was performed by magnetron sputtering on a 25-nm-thick Ni prelayer at 525–625 °C and yielded a continuous, highly crystalline film with a columnar structure. A Ni disilicide intermediate layer formed as a result of the Ni reaction with Si deposit provides a sufficient site for the Si epitaxial growth because lattice mismatch is small between the two materials. The reaction between Ni and Si was observed to progress in several stages. The NixSiy phase evolution in a Ni:Si layer was studied by x-ray photoelectron …

Optical Coherent Communication System Using Phase Shift Keying, Syed Javaid Iqbal

Student Works (2000-2009)

This thesis presents the experimental study and design of a coherent communication system by using phase shift keying (PSK). Systems are designed by using all passive elements, which make the system very easy to operate, and less maintenance is required. All the PSK designs are based on a single light source. In this thesis there are five different types of PSK with a single light source communication systems are designed. All designs are experimentally tested in free space. The systems are • All optical two-channel PSK communication system, by using single light source, "All optical single channel, two-way PSK communication, …