Electrical and Electronics Commons^™

Residual Strength Analysisof Asymmetrically Damaged Ship Hull Girderusing Beam Finite Element Method, Muhammad Zubair Muis Alie

Makara Journal of Technology

The objective of the present study is to analyze the residual strength of asymmetrically damaged ship hull girder under longitudinal bending. Beam Finite Element Method is used for the assessment of the residual strength of two single hull bulk carriers (Ship B1 and Ship B4) and a three-cargo-hold model of a single-side Panamax Bulk Carrier in hogging and sagging conditions. The Smith’s method is adopted and implemented into Beam Finite Element Method. An efficient solution procedure is applied; i.e. by assuming the cross section remains plane, the vertical bending moment is applied to the cross section and three-cargo-hold model. As …

Discrete Power Control In Heterogenous Networks, Yuanyuan Wang, Wibowo Hardjawana, Branka Vucetic

Makara Journal of Technology

In heterogeneous networks (HetNets) where femtocell base stations (FBSs) are deployed within the radio coverage of macrocell base stations (MBSs) to increase network capacity, co-channel interference limits overall system performance with universal frequency reuse. This paper investigates new distributed downlink discrete power control scheme for FBSs in HetNets with FBSs cooperation. The objective of the proposed power control scheme is to maximize the number of simultaneous FBSs transmissions in a single transmission wireless channel where each FBS is allowed to transmit only if the signal-to-interference-noise ratio (SINR) requirements for both FBSs and MBS users are satisfied. We apply a stochastic …

Multi-Project Scheduling Cost Optimization In A Machine Manufacturer Engineer-To-Order, Farizal Farizal, Amar Rachman, Tifani Tandean, Sumarsono Sudarto, Katsuhiko Takahashi

Makara Journal of Technology

This paper discusses the utilization of mixed integer linear programming (MILP) model to optimize cost for multiproject scheduling in a machine maker company. The objective is to minimize total project’s penalty cost and labor cost. The model formulated shows how to achieve the objective i.e. whether to use outsourcing or overtime to finish all projects. The model of multi-project scheduling was solved by Branch & Bound algorithm coded in Lingo 14.0 software. The case study shows that if a company wants to minimize lateness, it should use overtime instead of outsourcing, which minimize total lateness of projects by 144 days …

Analysis Of Arm Movement Prediction By Using The Electroencephalography Signal, Reza Darmakusuma, Ary Setijadi Prihatmanto, Adi Indrayanto, Tati Latifah Mengko, Lidwina Ayu Andarini, Achmad Furqon Idrus

Makara Journal of Technology

Various technological approaches have been developed in order to help those people who are unfortunate enough to be afflicted with different types of paralysis which limit them in performing their daily life activities independently. One of the proposed technologies is the Brain-Computer Interface (BCI). The BCI system uses electroencephalography (EEG) which is generated by the subject’s mental activity as input, and converts it into commands. Some previous experiments have shown the capability of the BCI system to predict the movement intention before the actual movement is onset. Thus research has predicted the movement by discriminating between data in the “rest” …

Texture Analysis Using The Neutron Diffraction Method On The Non Standardized Austenitic Steel Process By Machining,Annealing, And Rolling, Tri Hardi Priyanto, Parikin Parikin, Meijuan Li

Makara Journal of Technology

Austenitic steel is one type of stainless steel which is widely used in the industry. Many studies on austenitic stainless steel have been performed to determine the physical properties using various types of equipment and methods. In this study, the neutron diffraction method is used to characterize the materials which have been made from minerals extracted from the mines in Indonesia. The materials consist of a granular ferro-scrap, nickel, ferro-chrome, ferro-manganese, and ferro-silicon added with a little titanium. Characterization of the materials was carried out in three processes, namely: machining, annealing, and rolling. Experimental results obtained from the machining process …

Maneuverability Of Ships With Small Draught In Steady Wind, Daeng Paroka, Andi Haris Muhammad, Syamsul Asri

Makara Journal of Technology

Wind force and moment may force a ship to drastically decrease its speed and use a large drift angle as well as a large rudder angle in order to maintain its course. Ships with a small draught might have more risk in maneuvering to its point of view compared with a ship with a larger draught. This paper discusses maneuverability of a ship with a small draught in steady wind. The effect of wind on ship speed, drift angle, and rudder angle are investigated in a steady state condition. Five different ratios of wind velocity to ship speed from 1.0 …

A Comparison Of American, Norwegian, And Russian Standards In Calculating The Wall Thickness Of Submarine Gas Pipeline, Cindy Dianita, Tatyana Vladimirovna Dmitrieva

Makara Journal of Technology

One of the key issues in the pipeline design is wall thickness calculation. This paper highlights a comparison of wall thickness calculation methods of submarine gas pipeline based on Norwegian Standard (DNV-OS-F101), Indonesian Standard SNI 3474 which refers to American Standard (ASME B31.8), and Russian Standard (VN39-1.9-005-98). A calculation of wall thickness for a submarine gas pipeline in Indonesia (pressure 12 MPa, external diameter 668 mm) gives the results of 18.2 mm (VN39-1.9-005-98), 16 mm (ASME B31.8), and 13.5 mm (DNV-OS-F101).The design formula of hoop stress due to internal pressure is interpreted in different ways for every standard. Only Norwegian …

Improved Sensitivity Mems Cantilever Sensor For Terahertz Photoacoustic Spectroscopy, Ronald A. Coutu Jr., Ivan R. Medvedev, Douglas T. Petkie

Faculty Publications

In this paper, a microelectromechanical system (MEMS) cantilever sensor was designed, modeled and fabricated to measure the terahertz (THz) radiation induced photoacoustic (PA) response of gases under low vacuum conditions. This work vastly improves cantilever sensitivity over previous efforts, by reducing internal beam stresses, minimizing out of plane beam curvature and optimizing beam damping. In addition, fabrication yield was improved by approximately 50% by filleting the cantilever’s anchor and free end to help reduce high stress areas that occurred during device fabrication and processing. All of the cantilever sensors were fabricated using silicon-on-insulator (SOI) wafers and tested in a custom …

System And Method For Identifying Electrical Properties Of Integrate Circuits, Mary Y. Lanzerotti

AFIT Patents

A new method for displaying electrical properties for integrated circuit (IC) layout designs provides for improved human visualization of those properties and comparison of as designed layout design parameters to as specified layout design parameters and to as manufactured layout parameters. The method starts with a circuitry as designed layout in a first digital format, extracts values for electrical properties from that circuitry as designed layout then annotates those values back into the first digital format. The annotated circuitry as designed layout is then converted from the first digital format to a second digital format that can be converted to …

Rider's Aid, E-Bike Kit, Song Wang

All Undergraduate Projects

When it comes to observing the schema of upgrading bicycles into a hybrid model, the existing model usually costs hundreds of dollars and more than one hour of installation since it requires the process of replacing a wheel or even purchasing a new bicycle. But in fact, it was not necessary to remove the original wheel because the key to achieve power drive could be taken as an external function added to the primitive bike. Under the conditions of retaining applicability and safety that transportation should never get rid of, this project was focusing on reducing budget and saving time …

Comparing Various Hardware/Software Solutions And Conversion Methods For Controller Area Network (Can) Bus Data Collection, Samuel E. Marx, Joe D. Luck, Santosh Pitla, Roger M. Hoy

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Various hardware and software solutions exist for collecting Controller Area Network (CAN) bus data. Digital data accuracy could vary based upon different data logging methods (e.g., hardware/software timing, processor timing, etc.). CAN bus data were collected from agricultural tractors using multiple data acquisition solutions to quantify differences among collection methods and demonstrate potential data accumulation rates. Two types of data were observed for this study. The first, CAN bus frame data, represents data collected for each line of hex data sent from an ECU. One issue with frame data is the resulting large file sizes, therefore a second logging format …

G-Code Generation For Multi-Process 3d Printing, Callum Peter Bailey

Open Access Theses & Dissertations

Since the inception of stereolithography in the 1980s, interest in 3D printing has exploded, with desktop 3D printers now commercially accessible to the general public. In recent years, next-generation multifunctional technologies have been developed, which combine 3D printing with other technologies such as wire embedding, foil embedding, CNC machining, and robotic component placement, enabling complex parts to be made on a single multifunctional machine.

However, the complexity of these integrated processes exceeds the capabilities of established design tools. To this end, this Thesis aims to develop a multi-functional design solution that can automatically generate final control code for next-generation multifunctional …

Using Photovoltaics To Power Electrochemical Chloride Extraction From Concrete, Sean Bond, Lynette O'Callaghan, Niall Holmes Dr., Brian Norton

Conference papers

Corrosion of embedded steel in reinforced concrete (RC) is a world-wide problem, that reduces structural performance and lifespan. Chloride attack may be a result of seawater, de-icing salts or contaminated admixtures, brought on by ingress of chlorides into the concrete. Electrochemical Chloride Extraction (ECE) is a non-destructive treatment for contaminated RC structures, that due to uncertainty of treatment times and applied current densities, is only 50% effective. It is often diesel powered has an environmental impact and often very costly due to the long treatment times. To improve the efficiency of ECE the influences of concrete resistance, cement type and …

Electrokinetic Phenomena In Pencil Lead-Based Microfluidics, Yashar Bashirzadeh, Venkat Maruthamuthu, Shizhi Qian

Mechanical & Aerospace Engineering Faculty Publications

Fabrication of microchannels and associated electrodes to generate electrokinetic phenomena often involves costly materials and considerable effort. In this study, we used graphite pencil-leads as low cost, disposable 3D electrodes to investigate various electrokinetic phenomena in straight cylindrical microchannels, which were themselves fabricated by using a graphite rod as the microchannel mold. Individual pencil-leads were employed as the micro-electrodes arranged along the side walls of the microchannel. Efficient electrokinetic phenomena provided by the 3D electrodes, including alternating current electroosmosis (ACEO), induced-charge electroosmosis (ICEO), and dielectrophoresis (DEP), were demonstrated by the introduced pencil-lead based microfluidic devices. The electrokinetic phenomena were characterized …

Creating Multi-Functional G-Code For Multi-Process Additive Manufacturing, Efrain Aguilera Jr

Open Access Theses & Dissertations

Additive manufacturing (AM) started over thirty years ago and with it a manufacturing revolution that moves industrial production into the personal home. With recent interest shifting into multi-functional parts fabricated through AM technologies, unified systems are being developed. Merging different manufacturing technologies into one single machine is a challenge but undergoing research has shown promise in the development of multi-functional systems. Concurrent work is being done in the software, automation, and hardware aspect of multi-functional systems. An effort to use industry compatible Computer Aided Design (CAD) software to design multi-functional parts including circuits, micro-machining, and foil embedding then exporting and …

Modeling Of Piezoelectric Traveling Wave Rotary Ultrasonic Motors With The Finite Volume Method, Ivan Arturo Renteria Marquez

Open Access Theses & Dissertations

In 1983 Toshiiku Sashida developed a new motor concept called Piezoelectric Traveling Wave Rotary Ultrasonic Motor (PTRUSM). The advantages of these motors include high torque at low speed, absence of a generated magnetic field, and high potential for miniaturization. Unfortunately PTRUSMs have some disadvantages that limit the areas of applications for these types of motors. The disadvantages are a short operating life (about 1000 hours), small output power, and the need of a complex motor controller.

On one hand, these motors have been used in satellites, mobile phones, photocopiers, robotic arms, telescopes, automobiles, and camera autofocusing. On the other hand, …

Electromechanics Of An Ocean Current Turbine, Vasileios Tzelepis

LSU New Orleans Theses and Dissertations

The development of a numeric simulation for predicting the performance of an Ocean Current Energy Conversion System is presented in this thesis along with a control system development using a PID controller for the achievement of specified rotational velocity set-points. In the beginning, this numeric model is implemented in MATLAB/Simulink® and it is used to predict the performance of a three phase squirrel single-cage type induction motor/generator in two different cases. The first case is a small 3 meter rotor diameter, 20 kW ocean current turbine with fixed pitch blades, and the second case a 20 …

Improving Renewable Energy Transition Acceptance: A Simulation Gaming Approach On A Multi Actor Setting In The Netherlands, Aziiz Sutrisno, Jac A. M. Vennix, Noor Syaifudin

Makara Journal of Technology

The Netherlands have tried very hard to increase their renewable energy sources (RES) shares to fulfill the European Union target in 2050. However, RES performance did not show the expected result as the performance declined in 2009 producing even wider gap compare to the target. The Dutch government’s tried to incorporate all interested stakeholders by forming the Dutch energy transition task force. Nevertheless, the task force’s result is also not showing a desirable trend. Key reasons behind the Dutch low RES performance are the lack of shared understanding and positive attitude toward RES development among interested actors. This research uses …

Dual-Band Singly-Fed Proximity-Coupled Tip-Truncated Triangular Patch Array For Land Vehicle Mobile System, Basari Basari, Josaphat Tetuko Sri Sumantyo

Makara Journal of Technology

This paper proposes a dual-band left-handed circularly polarized triangular-patch array that is developed for land vehicle mobile system aimed at mobile satellite communications. The array consists of six tip-truncated triangular patches, which the first three patches are used for reception and the second three patches are used for transmission purpose. Each of three-patches has a beam pattern that can be switched in three different 120°-coverage beam in azimuth-cut plane at a minimum targeted gain at a desired elevation angle. The targeted minimum gain of the array is 5 dBic, in order for data communications with a large geostationary satellite can …

Improvement Of Quality Of Carica Papaya L. With Clove Oil As Preservative In Edible Coating Technology, Eny Kusrini, Anwar Usman, Chrispine Deksita Wisakanti, Rita Arbianti, Dedy Alharis Nasution

Makara Journal of Technology

We have studied utilization of essential clove oil, extracted from clove buds by hydrodistillation, as preservative in edible packaging technology. Preservative of essential clove oil was applied on chopped papaya fruits by using two methods, namely spray and brush. The effects of concentration of clove oil from 0.05 to 0.20% on the preservation of papaya fruits (Carica papaya L.) at room temperature (25 °C) were also evaluated. Physicochemical and in vitro microbiological activities on the papaya fruits that were stored at 25 oC and 85-90% relative humidity were investigated in details. The results indicate that the clove oil at concentration …

Calibration Of Numerical Model For Shoreline Change Prediction Using Satellite Imagery Data, Sigit Sutikno, Keisuke Murakami, Dwi Puspo Handoyo, Manyuk Fauzi

Makara Journal of Technology

This paper presents a method for calibration of numerical model for shoreline change prediction using satellite imagery data in muddy beach. Tanjung Motong beach, a muddy beach that is suffered high abrasion in Rangsang Island, Riau province, Indonesia was picked as study area. The primary numerical modeling tool used in this research was GENESIS (GENEralized Model for Simulating Shoreline change), which has been successfully applied in many case studies of shoreline change phenomena on a sandy beach.The model was calibrated using two extracted coastlines satellite imagery data, such as Landsat-5 TM and Landsat-8 OLI/TIRS. The extracted coastline data were analyzed …

Independency Of Elasticity On Residual Stress Of Room Temperature Rolled Stainless Steel 304 Plates For Structure Materials, Parikin Parikin, David Allen

Makara Journal of Technology

Mechanical strengths of materials are widely expected in general constructions of any building. These properties depend on its formation (cold/hot forming) during fabrication. This research was carried out on cold-rolled stainless steel (SS) 304 plates, which were deformed to 0, 34, 84, and 152% reduction in thickness. The tests were conducted using Vickers method. Ultra micro indentation system (UMIS) 2000 was used to determine the mechanical properties of the material, i.e.: hardness, modulus elasticity, and residual stresses. The microstructures showed lengthening outcropping due to stress corrosion cracking for all specimens. It was found that the tensile residual stress in a …

Oxidation Process Of H 2 O /Uv For Cod Reduction Of Wastewater From Soybean Tofu Production, Komala Pontas, Abrar Muslim

Makara Journal of Technology

Chemical Oxygen Demand (COD) reduction of wastewater from soybean tofu production was studied by conducting advanced oxidation process (AOP) using hydrogen peroxide with UV radiation catalysts in a closed cylindrical glass reactor. The hydroxyl radical (*OH) concentration from H2O2 decomposition was modeled, and exponential trends were found for the *OH concentration over radiation time and operation temperature. As a result, it was found that the maximal *OH concentration was 0.209 mol L-1 at 240 minutes and 50 °C. The *OH concentration exponentially increased following rise in operation temperature. The H2O2/UV AOP application reduced COD concentration to approximately 42.41% from 10,545 …

Uplift Of Shoreline Regions On Pagai Island Due To The September 12, 2007 Mw 8.4 Earthquake Captured By Sar Image, Ashar Muda Lubis

Makara Journal of Technology

At least 25 people were killed by the September 12, 2007 Mw 8.4 Bengkulu earthquake, and many buildings were destroyed in Bengkulu and West Sumatra provinces. It is very important to estimate the earth surface deformation due to the earthquake to understand the rupture size and its process. The aim of this research is to estimate the shoreline change and vertical displacement on Pagai Island associated with the September 12, 2007 Mw 8.4 Bengkulu earthquake. The intensity of ALOS-PALSAR satellite images is used to access the pattern of displacement. The result shows that Pagai Island demonstrated huge uplift due to …

Effect Of Fly Ash Fortification In The Manufacture Process Of Making Concrete Towards Characteristics Of Concrete In Sulfuric Acid Solution, Asep Handaya Saputra, Muhammad Shohibi, Masatoshi Kubouchi

Makara Journal of Technology

Fly ash is a silica or alumino silica material that can be used as a constituent of cement in the concrete manufacturing process. Utilization of fly ash aims to improve durability and minimize the reduction of concrete’s compressive strength exposed to an acidic environment, which can be achieved through the pozzolanic reaction of fly ash with Ca(OH)2 within concrete. The reduced content of Ca(OH)2 through pozzolanic reaction will minimize the tendency of ettringite formation (compounds that cause deterioration and decrease the compressive strength of concrete). In order to determine the relation between fly ash replenishment into concrete with concrete’s characteristics …

Cultural Change Through Bim: Driving Lean Transformation In Education, Avril Behan, Malachy Mathews, Kevin Furlong, Ciara Ahern, Una Beagon, Peter Brennan, Colin Conway, Lee Corcoran, Pierce Fahy, Alan Hore, Barry Mcauley, Trevor Woods

Conference papers

This paper presents a case study of how the adoption of BIM-based practices in the AECO industry is being reflected by cultural change in higher education in Ireland. The silo-mentality that has dominated the AECO sector for more than a century has, despite numerous reorganisations, been replicated in the structures of educational institutions, including in Dublin Institute of Technology since the inception of its founding colleges in the late 1800s. Most AECO programmes must include content that is external to the programme’s specific discipline. Through the School structures of the Institute, delivery of such content is known as "service teaching" …

Novel Applications Of A Thermally Tunable Bistable Buckling Silicon-On-Insulator (Soi) Microfabricated Membrane, Robert A. Lake

Theses and Dissertations

Buckled membranes are commonly used microelectromechanical systems (MEMS) structures. Recent work has demonstrated that the deflection and stiffness of these membranes can be tuned through localized joule heating. These devices were implemented into the design and fabrication of two novel device applications, a tunable pressure sensor and a steerable micromirror. A differential pressure across the membrane causes de reflection, up or down, which can be measured and related to a specific pressure. By tuning the stiffness of the membrane, its pressure response is varied providing a wider range of application for the pressure sensor. A 2.0mm by 2.0mm square membrane …

Integrating Systems For Liquid/Substrate Characterization And Functional Printing, Jianyi Du, J. William Boley, Rebecca K. Kramer

The Summer Undergraduate Research Fellowship (SURF) Symposium

Gallium-Indium alloys are recently applied in fabricating soft devices, such as stretchable sensors, electric circuits, micro pumps and optics. Its printability demonstrates the possibility for a wide extension of the application. Current fabrication methods are inefficient when printing is most handled manually, and are highly dependent on material properties. There is need for a fast way to characterize material properties, and to functionally print the given shape on the substrate. This paper presents the construction of an efficiently integrated system with optical imaging and functional printing for Gallium-Indium alloys. The imaging section allows for characterization of material properties to fast …

Application Of Fiscal Incentives For Development Of East Natuna Gas Field For Long-Term National Natural Gas Demand, Marwan Batubara, Widodo Wahyu Purwanto, Akhmad Fauzi

Makara Journal of Technology

East Natuna gas field, which has proven reserves of 46 trillion cubic feet, is projected to meet long-term natural gas needs. However, CO2-content of the gas reserves reaches 71%, leading to expensive development costs. This research investigates the feasibility of the field based on several fiscal incentives. Firstly, gas supply-demand until year 2040 was analyzed. Then, based on the analysis, the field was developed using high CO2 gas separation technology to produce gas of 1300 MMSCFD in 2023, 2600 MMSCFD in 2031, and 3900 MMSCFD in 2039. Finally, the economic feasibility was assessed using cash flow analysis in accordance with …

Thermodynamic Analysis Of Irreversible Heat-Transformers, Niccolo` Giannetti, Arnas Arnas, Andrea Rocchetti, Kiyoshi Saito

Makara Journal of Technology

Absorption heat transformers extend the possibilities for efficient and environment-friendly energy conversion processes. Based on a general thermodynamic model of three-thermal cycles with finite thermal capacity of the heat sources, this paper is intent upon analyzing and optimizing the performance of absorption heat transformers, by including the influence of irreversibility in the analytical expression of the system efficiency. Dimensionless parameters for an overall optimization are defined and a first screening is performed to clarify their influence. Dependence on the main factors is highlighted to suggest how to change them in order to enhance the whole system performance. Under this point …