Electrical and Electronics Commons^™

Experimental Evaluation Of Three Different Humidity Conditions To Physical And Mechanical Properties Of Three Different Mixtures Of Unfired Soil Bricks, Heru Purnomo, Srikandi Wahyu Arini

Makara Journal of Technology

Unfired brick is considered as a more environmentally friendly material than fired brick. It has lower mechanical properties than that of fired brick where humidity influences both bricks. Physical and mechanical properties of unfired bricks made of three kinds of mixtures were studied experimentally under three humidity conditions. The first kind of unfired brick was made only with soil and water while the second type was made of a mixture of soil, water and lime, and the third type was a mixture of soil, water, lime and uniform treated coir where 4% of lime mass was substituted with coir mass. …

Energy Transformation And Conservation Investigation, Mike Jackson, Holly Haney

High School Lesson Plans

Students will use a thermoelectric generator module to analyze the relationship between thermal and electrical energies. Using data collection sensors and analysis software, students will investigate the relationship between the temperature gradient across a thermoelectric generator module and the resulting electrical potential. Students will then use their data and analysis to solve problems relating to waste thermal energy in electrical systems and communicate their work to their peers and teacher.

The Comparative Analysis Of The Performances Of Four And Six Pole Pairs Permanent Magnet Synchronous Generator, Ra Msuya

Tanzania Journal of Engineering and Technology (TJET)

Wind power applications using multi-poles permanent magnet generators have become very attractive especially in small ratings. Low-speed multi-pole PM generators are maintenance-free and may be used in different climate conditions. Most of the low speed wind turbine generators presented is permanent magnet machines, which have advantages of high efficiency and reliability since there is no need of external excitation and conductor losses are removed from the rotor. From the study two types of PM AC generator are designed with 6 pole pairs and the other one with 4 pole pairs. These generators were designed and analysed using Maxwell software. The …

Nonlinear Direct Torque Control Of Interior Permanent Magnet Synchronous Motor Drive, Jackson Justo

Tanzania Journal of Engineering and Technology (TJET)

This paper presents a nonlinear direct torque control (NDTC) strategy of interior permanent magnet synchronous motors (IPMSMs) for electric vehicle (EV) propulsion. The proposed NDTC scheme applies a nonlinear model of IPMSM to dynamically determine the optimal switching states that optimize the EV drivers’ decision to reduce the workload. Moreover, the proposed NDTC method has a simple control structure and can explicitly handle system constraints and nonlinearities. The performance evaluation is conducted via a prototype IPMSM test-bed with a TMS320F28335 DSP. Comparative experimental results provide the evidence of improvements of the proposed NDTC strategy over the conventional DTC strategy by …

A Low-Cost Experimental Testbed For Multi-Agent System Coordination Control, Victor Fernandez-Kim

LSU Master's Theses

A multi-agent system can be defined as a coordinated network of mobile, physical agents that execute complex tasks beyond their individual capabilities. Observations of biological multi-agent systems in nature reveal that these ``super-organisms” accomplish large scale tasks by leveraging the inherent advantages of a coordinated group. With this in mind, such systems have the potential to positively impact a wide variety of engineering applications (e.g. surveillance, self-driving cars, and mobile sensor networks). The current state of research in the area of multi-agent systems is quickly evolving from the theoretical development of coordination control algorithms and their computer simulations to experimental …

Epitaxial Growth Of Iii-Nitride Nanostructures And Their Optoelectronic Applications, Moab Rajan Philip

Dissertations

Light-emitting diodes (LEDs) using III-nitride nanowire heterostructures have been intensively studied as promising candidates for future phosphor-free solid-state lighting and full-color displays. Compared to conventional GaN-based planar LEDs, III-nitride nanowire LEDs exhibit numerous advantages including greatly reduced dislocation densities, polarization fields, and quantum-confined Stark effect due to the effective lateral stress relaxation, promising high efficiency full-color LEDs. Beside these advantages, however, several factors have been identified as the limiting factors for further enhancing the nanowire LED quantum efficiency and light output power. Some of the most probable causes have been identified as due to the lack of carrier confinement in …

Surface Engineering Solutions For Immersion Phase Change Cooling Of Electronics, Brendon M. Doran

Master's Theses

Micro- and nano-scale surface modifications have been a subject of great interest for enhancing the pool boiling heat transfer performance of immersion cooling systems due to their ability to augment surface area, improve wickability, and increase nucleation site density. However, many of the surface modification technologies that have been previously demonstrated show a lack of evidence concerning scalability for use at an industrial level. In this work, the pool boiling heat transfer performance of nanoporous anodic aluminum oxide (AAO) films, copper oxide (CuO) nanostructure coatings, and 1D roll-molded microfin arrays has been studied. Each of these technologies possess scalability in …

Danny’S Recumbent Bike Accessibility Device Final Design Report, Joseph J. Lee, Huy Nguyen, Jack Mcatee, John Kulick

Mechanical Engineering

The purpose of this document is to fully define our design solution and explain our manufacturing and testing results. Our project’s goal is to find a way to allow Danny Knutson, a retired Navy pilot and incomplete quadriplegic with limited use of his arms and an impaired sense of balance, to enter and exit his recumbent tricycle without any discomfort for him or his aide. We completed multiple interviews with Danny, patent research, existing product research, and other technical literature research in order to fully understand the problem. We synthesized this information to create a concrete list of customer wants …

Civilian Acquirer For Fire Safety (Cafs), Antara Das, Marcus Allen, Clark Shaver

Posters

The department of Electronics Engineering Technology (EET) of Pittsburg State University has designed a prototype of an autonomous rover to help firefighters to find lives trapped in a building during an event of fire. The rover prototype has been named CAFS, which is the abbreviated form for Civilian Acquirer for Fire Safety. This device intends to produce the first ever autonomous system to locate, record, and transmit people’s location from within a building to a user outside of the building. According to the National Fire Protection Association (NFPA), on 2017, 72% of the fire that happened in the USA was …

Molecularly Conductive Behavior Of Blended Polymer Electrolyte-Based Cmc/Pva, Noor Saadiah Mohd Ali, Dishen Zhang, Yuki Nagao, Ahmad Salihin Samsudin

Makara Journal of Technology

This study investigated the electrical conduction and structural behavior of blended polymer electrolyte (BPE)-based carboxymethyl cellulose (CMC) and polyvinyl alcohol (PVA) in the development of solid-state electrochemical devices. Based on impedance spectroscopy and correlating Fourier transform infrared (FTIR) with thermogravimetric analysis, a framework was proposed to explain the structural enhancement of the BPE system. As revealed by FTIR, the optimum conductivity of CMC/PVA BPEs was 9.21 × 10−6 Scm−1 for 80:20 composition attributed to the intermolecular attraction between the polymers. Thermal stability of the CMC/PVA was influenced by the formation of a hydrogen bond between the hydroxyl (-OH), carboxylate (-COO-), …

Multistage Sonication Effect On The Composition And Properties Of Degraded Chitosan Product, Nurul Laili Arifin, Emma Savitri, Anjar Indah, Fesa Putra, Sumarno Sumarno

Makara Journal of Technology

The sonication method randomly breaks polymer chains to produce a varied distribution of products. A scheme with multi-stage sonication steps is proposed to identify oligomers and low molecular weight chitosan based on changes to the degrad-ed product. For each sonication level, 1% (w/v) chitosan in 1% (v/v) aqueous acetic acid was sonicated for 120 min at 60 °C. The products of the sonication treatment were deprotonized by adding an alkali solution, freeze dried and insoluble product re-sonicated until a low molecular weight was produced. Low molecular weight chitosan/insoluble products were character-ized with Fourier-transform infrared spectra (FT-IR) and X-ray diffraction (XRD) …

Study Of Zno Nanospheres Fabricated Via Thermal Evaporation For Solar Cell Application, Fatin Farisha Alia Azmi, Bouchta Sahraoui, Saifful Kamaluddin Muzakir

Makara Journal of Technology

A solar cell is a device that absorbs light energy to generate electrical energy. A typical example of a solar cell is the quantum dot solar cell (QDSC), which consists of three main components: (i) fluorophore: the component that absorbs light and generates excited state electrons and holes, (ii) photoelectrode: the component that transports the excited state electron and prevents recombination of excited state electrons and holes, and (iii) electrolyte: the component that re-plenishes the vacancy left by the excited electron in the hole. Despite the increasing number of research in the QDSC field, to date, a device with significant …

Electrical Properties Of A Novel Solid Biopolymer Electrolyte Based On Algi-Nate Incorporated With Citric Acid, Ahmad Faizrin Ahmad Fuzlin, Noor Syahida Ismail, Yuki Nagao, Ahmad Salihin Samsudin

Makara Journal of Technology

In the present study, a novel solid biopolymer electrolyte (SBE) system is introduced by doping citric acid into alginate polymer. A sample of the alginate-citric acid SBE system was prepared via a solution casting technique. Using electrical impedance spectroscopy (EIS), the electrolytes of alginate-citric acid analyzed from 5 Hz to 1 MHz achieved the highest conductivity at 20 wt.% of 5.49 × 10-7 S cm-1. The temperature dependence of various citric acid amounts obeyed the Arrhenius rule with R2~1, where all SBE systems were thermally activated with increasing temperature. The dielectric studies of the alginate-citric acid SBE system showed non-Debye …

Wavelet Transform On Digital Rainbow Hologram Based On Spectral Compression For Quality Enhancement In 3d Display Media, Ucuk Darusalam, Panca Dewi Pamungkasari

Makara Journal of Technology

A digital rainbow hologram (DRH) is a potential next-generation three-dimensional display media for the development of modern and smart electronics devices. It is one of the methods that can support the characteristic whereby a realistic display media occupies the space that the real object would have occupied. Since a rainbow hologram records a large amount of spatial or temporal frequency component from the object that represents the rainbow spectrum, a large amount of information needs to be decoded digitally. In this paper, to reconstruct a DRH, we propose a novel method based on the modulation of red, green, and blue …

Data Fusion Method Based On Adaptive Kalman Filtering, Bernadus Herdi Sirenden

Makara Journal of Technology

This paper discusses data fusion methods to combine the data from a rotary encoder and ultrasonic sensor. Both sensors are used in a micro-flow calibration system developed by the Research Center of Metrology LIPI. The methods studied are hierarchical data fusion and Kalman filtering. Three types of Kalman filters (KFs) are compared: the conventional Kalman filter and two adaptive Kalman filters. Moreover, a method to combine the uncertainty results from KF in hierarchical data fusion is proposed. The aim of this study is to find appropriate methods of data fusion that can be implemented in micro-flow calibration systems. Data from …

Sorption-Based Energy Storage Systems: A Review, Kyaw Thu, Nasruddin Nasruddin, Sourav Mitra, Bidyut Baran Saha

Makara Journal of Technology

Mismatched timing between the supply and demand of energy calls for reliable storage systems. Energy storage systems have become further significant with the widespread implementation of renewable energy. These systems can mitigate problems that are often associated with renewable energy sources such as supply unreliability while meeting the de-mand during peak hours. Energy can be stored in various forms, yet storage systems can be generally grouped based on their output forms, namely (i) electricity and (ii) heat or thermal energy. Electrical energy is the most convenient and effective form since it can power almost all modern devices. However, the electricity …

Design Of A Low-Cost Data Acquisition System For Rotordynamic Data Collection, Gregory S. Pellegrino

Master's Theses

A data acquisition system (DAQ) was designed based on the use of a STM32 microcontroller. Its purpose is to provide a transparent and low-cost alternative to commercially available DAQs, providing educators a means to teach students about the process through which data are collected as well as the uses of collected data. The DAQ was designed to collect data from rotating machinery spinning at a speed up to 10,000 RPM and send this data to a computer through a USB 2.0 full-speed connection. Multitasking code was written for the DAQ to allow for data to be simultaneously collected and transferred …

Networked Microgrid Optimization And Energy Management, Robert S. Jane

Dissertations, Master's Theses and Master's Reports

Military vehicles possess attributes consistent with a microgrid, containing electrical energy generation, storage, government furnished equipment (GFE), and the ability to share these capabilities via interconnection. Many military vehicles have significant energy storage capacity to satisfy silent watch requirements, making them particularly well-suited to share their energy storage capabilities with stationary microgrids for more efficient energy management. Further, the energy generation capacity and the fuel consumption rate of the vehicles are comparable to standard diesel generators, for certain scenarios, the use of the vehicles could result in more efficient operation. Energy management of a microgrid is an open area of …

Optimal Power Flow Control Of Networked Dc Microgrids, Eddy H. Trinklein

Dissertations, Master's Theses and Master's Reports

The US military is moving toward the electrification of many weapon systems and platforms. Advanced weapon systems such as high energy radar, electro-magnetic kinetic weapons and directed energy pose significant integration challenges due to their pulsed power electrical load profile. Additionally, the weapons platforms, including ships, aircraft, and vehicles can be studied as a mobile microgrids with multiple generation sources, loads, and energy storage. There is also a desire to extend the mission profile and capabilities of these systems. Common goals are to increase fuel efficiency, maintaining system stability, and reduce energy storage size as typically required to enable pulsed …

Ascorbic Acid Degradation In Cut Lemon Packaged Using Oxygen Scavenging Active Film During Storage, Kurniawan Yuniarto, Setyo Purwanto, Bruce Ari Welt, Anang Lastriyanto

Makara Journal of Technology

Oxygen scavenging active film can be used to prevent diffusion of free oxygen due to the action of permeation mechanism. In this study, biodegradable oxygen scavenging plastic film was designed by incorporating an antioxidant agent into plasticized polylactic acid or PLA-PEG (PPLA). Butylated hydroxytoluene (BHT) was added at different concentrations into the matrix of the PPLA film using a direct casting method to produce oxygen scavenging active film. The antiradical activity of the oxygen scavenging active film was observed, which could be applied for preventing vitamin C degradation in cut lemon during storage. The antiradical activity of the active film …

Conversion Of Heat Energy From Cooling Water Of Diesel Engine To Electrical Energy Using Thermoelectric Generator, Muhammad Hasan Albana

Makara Journal of Technology

This research objective is to convert heat from the radiator fluid of a diesel engine to electrical energy by utilizing a thermoelectric generator (TEG). The TEG consists of 20 semiconductors (TE modules) and is equipped with a heat sink. The research shows that using the TEG, the heat of radiator fluid can be converted to electrical energy, although the electricity generated is small. The maximum electrical voltage generated by the TEG when modules were connected in series was 10 volts. When the TE modules were connected in parallel and series-parallel, the maximum voltages generated were 2.11 and 2.53 volts, respectively. …

Immittance Response On Carboxymethyl Cellulose Blend With Polyvinyl Alcohol- Doped Ammonium Bromide-Based Biopolymer Electrolyte, Norfatihah Mazuki, Yuki Nagao, Ahmad Salihin Samsudin

Makara Journal of Technology

The blended carboxymethyl cellulose (CMC) and polyvinyl alcohol (PVA) doped with various compositions of ammonium bromide (NH4Br)-based solid biopolymer electrolytes (SBEs) were prepared by using the casting method. In this present work, CMC/PVA–NH4Br SBE thin film was used to investigate the electrical conductivity via electrical impedance spectroscopy. The maximum conductivity obtained was 3.21 X 10−4 S cm−1 for sample AB20 at ambient temperature (303 K), and this result might be due to the increased number of charge carrier. A dielectric study was conducted to understand the conductivity behavior. The electrical properties have been measured as a function of frequency of …

Transition Metal Dichalcogenide For High-Performance Electrode Of Supercapacitor, Saifful Kamaluddin Muzakir, Ahmad Salihin Samsudin, Bouchta Sahraoui

Makara Journal of Technology

Molybdenum dichalcogenides have been reviewed from the perspectives of bandgap, conductivity, and oxidation states of transition metal. Researchers have concluded that a narrow-bandgap transition metal dichalcogenide with high conductivity could be achieved for the high-performance electrode of a supercapacitor.

The Importance Of Usability Aspect In M-Commerce Application For Satisfaction And Continuance Intention, Yassierli Yassierli, Vinsensius Vinsensius, M. S. Syed Mohamed

Makara Journal of Technology

There has been a rapid growing of m-commerce application in recent years due to the development of mobile communication technology and e-commerce business. However, only about 30% of online users, who conduct online searching, make online purchases. The low conversion rate seems to be correlated with poor usability aspect of most m-commerce applications and poor satisfaction reported by users. Research has reported that satisfaction and continuance intention in using m-commerce applications have relationships with service quality and information quality. In this study, a new model of user satisfaction and continuance intention in the context of mobile application was proposed by …

A 2.3/3.3-Ghz Dual Band Low Noise Amplifier Using Switchable Load Inductor In 0.18-Um Cmos Technology, Taufiq Alif Kurniawan, Hsiao-Chin Chen

Makara Journal of Technology

In this paper, the dual band low noise amplifier is designed in 0.18-μm CMOS technology. By combining the proposed switchable load inductor for gain controlling and the conventional inductive source degeneration topology, narrow band gain and good impedance matching are achieved at 2.3/3.3-GHz frequency bands. The new mathematical analysis of low noise amplifier design is derived to define the component parameters of the proposed circuits. The proposed low noise amplifier exhibits gain of 17.18 dB and 15.5 dB, and noise figure of 2.67 dB and 2.52 dB at the two frequency bands, respectively.

Automated Compilation Test System For Embedded System, Mohamad Khairi Ishak, Ooi Jun Hwan, Teh Jiashen, Nor Ashidi Mat Isa

Makara Journal of Technology

Embedded system testing involves testing an integration of software and hardware. It is increasingly difficult to evaluate the functionality of each module within a short time because of the increasing number of tests required. In this paper, a novel stepwise methodology involving the use of an automated compilation test system (ACTS) is proposed, to improve the quality of testing and optimize the testing time using automation. Using the proposed method, the testing coverage can be maximized, while minimizing the manual work and testing time required. This ACTS was used to automate the test code compilation and execution for different hardware …

Activated Carbon Fixed-Bed Adsorber Design For Treating Chromium Hexavalent Wastewater, Tedi Hudaya, Velicia Rachmat

Makara Journal of Technology

Pollution caused by industrial wastewater containing heavy metals is a major issue, primarily due to its toxic nature. A cheap yet effective method to deal with such wastewater is activated carbon adsorption. The purpose of this research is to evaluate and design a fixed bed adsorber with granular activated carbon as an adsorbent to process wastewater-containing chromium hexavalent (Cr 6+). Experiments show that the Langmuir isotherm fits the equilibrium data as effectively as the Freundlich isotherm. Activated carbon used in this research is Jacobi 2000® derived from bituminous coal. The lab scale inlet volumetric flow is 100 mL/h with different …

Development Of A Rapid Fatigue Life Testing Method For Reliability Assessment Of Flip-Chip Solder Interconnects, Cody Jackson Marbut

Graduate Theses and Dissertations

The underlying physics of failure are critical in assessing the long term reliability of power packages in their intended field applications, yet traditional reliability determination methods are largely inadequate when considering thermomechanical failures. With current reliability determination methods, long test durations, high costs, and a conglomerate of concurrent reliability degrading threat factors make effective understanding of device reliability difficult and expensive. In this work, an alternative reliability testing apparatus and associated protocol was developed to address these concerns; targeting rapid testing times with minimal cost while preserving fatigue life prediction accuracy. Two test stands were fabricated to evaluate device reliability …

Nanosatellite Launch Data-Logger (Sync), Christopher Martin Gerdom

Master's Theses

CubeSat designers are increasingly looking to incorporate delicate structures and optics into their payloads. These delicate payloads, however, may not survive the required absolute-worst-case launch vibration testing needed for flight certification. To help address this problem, and to better match testing conditions to real-world launch environments, this thesis introduces Sync, a compact 1/4U CubeSat payload designed to collect data on the vibrations and thermal environments CubeSats experience inside a deployer on the way to orbit. This data can be used to better understand the launch environment for different vehicles, and help develop new, more realistic testing guidelines that could enable …

Furnace System Improvements, Kenji K. Anzai, Ethan Fedor, Patrick Zailaa

Mechanical Engineering

This Final Design Review (FDR) documents the work done by the group to manufacture the system to deliver improvements to the furnace in the Cal Poly microfabrication laboratory (better known as the cleanroom). The document describes the material covered in the Scope of Work (SOW), including background research, customer needfinding, and the problem statement, material associated with concept development and selection for Preliminary Design Review (PDR), material detailing the design and manufacturing plan of the system for Critical Design Review (CDR), and new material detailing the manufacture of the system for FDR.

Research done for the SOW resulted in a …