Electrical and Electronics Commons^™

Long-Range Inertia Prediction Considering Contemporary Evolution Of Power Grid Networks, Peter M. Makolo

Tanzania Journal of Engineering and Technology (TJET)

Reduced network inertia due to high penetration levels of non-synchronous generators in modern power systems is becoming a pressing issue. As a result, very quick inertial responses are observed after contingency events in networks. Due to quick inertial responses, there is a practically very limited time interval for control actions in real-time. Thus, system operators need to understand the prior inertia values to plan, control, and operate the network securely. Long-range forecasting of the network's inertia values, in contrast to short-range forecasting techniques, can pinpoint when the network is most likely to be vulnerable in a reasonable time ahead. Thus, …

Assessment Of Wind Speed Characteristics And Available Wind Power Potential For Electricity Generation In Tanzania, Mwingereza John Kumwenda

Tanzania Journal of Engineering and Technology (TJET)

The energy demand and its associated crises are attracting significant attention due to population increase and economic growth especially in developing countries. Fossil fuel-based energy source stand as a prominent anthropogenic resource but they are accompanied with increased carbon emissions and heightened environmental concerns. Renewable energy sources such as wind energy can offers a lot of potential for sustainable growth in the energy sector of developing nations like Tanzania. Thus, this work investigated wind speed characteristics and available wind power potential in six selected regions in Tanzania with different topographical features for future electricity generation. The data of the wind …

Efficient Operation Of Direct Coupled Solar Home Pv System: A Case Of Solar Home Pv System Installed In Dodoma, Tanzania, Sarah P. Ayeng'o

Tanzania Journal of Engineering and Technology (TJET)

Direct coupled Photovoltaic (PV) system is a common topology among most of the off-grid communities in the world. This topology has less components hence resulting in low investment costs. However, it suffers much losses when battery operating voltage is far from maximum power point voltage of PV modules. This scenario can be attributed by different factors such as; variation in solar radiation, load profile and temperature. Efficient operation of these systems is required in order to reduce losses. Usually in direct coupled system, PV modules are connected in parallel with batteries through a charge controller hence making PV output to …

Solid Loading Effects On The Assembly Of Alumina Particles In Aqueous Suspensions Due To The Dielectrophoretic Forces, Sivakumar Chithamallu, Rohan Kiran Parai, Dipankar Ghosh

Mechanical & Aerospace Engineering Faculty Publications

Current work in situ investigated the mechanisms of the interparticle interactions that evolve in dilute aqueous alumina suspensions subjected to alternating current (AC) electric field and the effects of solid loading of suspensions. The interactions were investigated for alumina suspension compositions in the 0.005‒0.04 vol.% solid loading range. Field‐induced interactions evolved via particle motion and dynamic assembly, chain formation parallel to the direction of the applied field and chain growth, chain cross‐linking, and chain thickening. The evolution time of each of those events was rapidly accelerated with solid loading. While chain cross‐linking was negligible in low solid loading suspensions, a …

Implementation Of Quantized Artificial Neural Networks With Spintronic Stochastic Computing, Saadi Sabyasachi Mr.

Theses and Dissertations

Artificial intelligence or machine learning is going through a rapid expansion. It also incurs significant costs for power and device footprints. Various approaches are being explored to design energy and hardware efficient machine learning models. Stochastic computing has been proposed for efficient machine learning implementation. It requires a source of random number generation which poses some practical challenges. So spintronic solutions such as magnetic tunnel junction has been used for random number generation. Again, spintronic random number generation to implement high precision circuit is prone to device-to-device variations. Hence we designed quantized artificial neural network with spintronic stochastic computing which …

Rheology Of Alumina Suspensions Subjected To Alternating Current Electric Fields For Freeze-Casting, Sivakumar Chithamallu, Ruksana Baby, Jacob L. Jones, Dipankar Ghosh

Mechanical & Aerospace Engineering Faculty Publications

Alternating current (AC) electric field can extrinsically tune freeze‐cast microstructure, originating from field‐induced increase in viscosity of ceramic suspensions. However, the changes that occur in a ceramic suspension and rheological behavior, ultimately affecting freeze‐cast microstructure, are not well understood. Moreover, the effects of AC electrokinetic forces and temperature on viscosity need to be decoupled. The viscosity and temperature of ceramic suspensions subjected to AC field and direct heating were measured, revealing that the increase in viscosity is due to AC dielectrophoretic forces rather than field‐induced heating of suspension. The shear thinning behavior of suspensions characterized using a power‐law model reveals …

A Novel Intelligent Thermal Feedback Framework For Electric Motor Protection In Embedded Robotic Systems, Mohamed Shili, Salah Hammedi, Hicham Chaoui, Khaled Nouri

Electrical & Computer Engineering Faculty Publications

As robotic systems advance in autonomy and sophistication while being used in uncertain environments, the challenge of building reliable and robust electric motors that are embedded into robotic systems has never been a more important engineering problem. Thermal distress caused by extended operation or excessive loading can negatively affect a motor’s performance and efficiency and lead to catastrophic hardware failure. This paper proposes a novel intelligent control framework that includes real-time thermal feedback for hybrid electric motors that are embedded into robotic systems. The framework relies on adaptive control techniques and lightweight machine learning techniques to estimate internal motor temperatures …

An Investigation Into Energy Consumption And V2g Potential Of An Electric School Bus Fleet, Rupesh Dahal

Graduate Theses, Dissertations, and Problem Reports (ETD)

The transition towards sustainable public transportation demands detailed evaluation of alternative fuel technologies. This thesis presents a comprehensive energy assessment and comparative analysis of diesel and electric school buses (ESBs) operating within the Monongalia County school district, its Vehicle-to-Grid (V2G) potential, and efficiency analysis of charging system. Utilizing real-world operational data collected from buses running identical routes, the study quantifies and compares their mileage specific energy consumption. The analysis reveals an average fuel economy of approximately 6.17 miles per gallon (MPG) for the conventional diesel school bus, contrasted with an average energy consumption rate of 0.46 miles per kilowatt-hour (miles/kWh) …

Design, Fabrication, & Laboratory Testing Of A Strain Gage Instrumentation System For Marine Applications, Salem C. Homrighausen

UNF Graduate Theses and Dissertations

A strain gage-based instrumentation system was designed and fabricated to measure the moment present at the base of a mock, diesel-engine snorkel for a submerged vehicle designed to operate in the surf zone. Afterwards, a lab experiment was designed and executed to determine the accuracy of the instrument and a 2-dimensional, matrix-vector equation was formulated to relate pairs of voltages, Vx and Vy, to moments, Mx and My for the experiment. Three versions of this model were built. The first model was created using traditional statics equations governing strain, stress, moment, force. The second and third models were built directly …

3d Printed Microfluidic Fabrication Methodology, Characterization, Mechanical Design, And Applications In Electrostatic Artificial Muscles And Benthic Microbial Fuel Cells, Terak B. Hornik

Master's Theses

The fabrication of microfluidic devices often requires specialized methods. The development of these methods requires careful characterization and understanding of the processes involved. Using primarily PolyJet 3D printing technology, microfluidics offers a wide scope of applications such as microfluidic benthic microbial fuel cells (MBMFCs) and electrostatic artificial muscles. MBMFCs benefit from the confinement of the microbes resulting in close proximity between the electrode and the organisms. Using a modular design called the Sponge, assembly and upscaling is possible. Electrostatic artificial muscles benefit from a microfluidic approach due to the non-linearity of electrostatic attraction creating disproportionate benefits when miniaturized. When designed …

Design And Implementation Of An Inverted Short Baseline Acoustic Positioning System, Jakob Frabosilio

Master's Theses

This document details the design, implementation, testing, and analysis of an inverted short baseline acoustic positioning system. The system presented here is an above-water, air-based prototype for an underwater acoustic positioning system; it is designed to determine the position of remotely-operated underwater vehicles (ROVs) and autonomous underwater vehicles (AUVs) in the global frame using a method that does not drift over time.

A ground-truth positioning system is constructed using a stacked hexapod platform actuator, which mimics the motion of an AUV and provides the true position of an ultrasonic microphone array. An ultrasonic transmitter sends a pulse of sound towards …

Shape Memory Alloy Capsule Micropump For Drug Delivery Applications, Youssef Mohamed Kotb

Theses and Dissertations

Implantable drug delivery devices have many benefits over traditional drug administration techniques and have attracted a lot of attention in recent years. By delivering the medication directly to the tissue, they enable the use of larger localized concentrations, enhancing the efficacy of the treatment. Passive-release drug delivery systems, one of the various ways to provide medication, are great inventions. However, they cannot dispense the medication on demand since they are nonprogrammable. Therefore, active actuators are more advantageous in delivery applications. Smart material actuators, however, have greatly increased in popularity for manufacturing wearable and implantable micropumps due to their high energy …

2024 Marine Energy Collegiate Competition, Nora Riedinger, Miles Mikkelsen, Brendan Stratford, Derek Tom, Zach Kwast, Harmon Yanikian-Sutton, Kennedy Urcelay, Tori Thomas, Brady Caron

Mechanical Engineering

PolyWave Energy is the second team from California Polytechnic University at San Luis Obispo to compete in the Marine Energy Collegiate Competition. PolyWave Energy consists of Mechanical Engineering, Electrical Engineering, and Business Administration students who have worked together from September 2023 to May 2024 on designing, building, and testing a marine power device to serve a selected market.

In response to the escalating concerns surrounding carbon emissions, climate change, and the depletion of fossil fuels, California Polytechnic State University’s Polywave Energy team has developed a sustainable and reliable energy source for Autonomous Underwater Vehicle (AUV) charging. Through extensive research of …

Impact Force Helmet Device For Concussion Monitoring, Patrice Mulligan, Karina Mealey, Zack Borthwick, Benjamin Fick

General Engineering

To track head trauma in football, our device is placed inside a football helmet to measure both linear and gyroscopic (rotational) accelerations. These measurements are taken using an ADXL375 linear accelerometer and an LSM6DSOX accelerometer and gyroscope. The data from these sensors is processed and transmitted wirelessly by a SparkFun Thing Plus microcontroller to another SparkFun Thing Plus microcontroller connected to a laptop on the sidelines. Our program on the laptop stores the acceleration impact data into a .csv file for each player. If a likely concussive impact is detected, the program displays a popup warning. Testing results were promising …

Interaction Of Particles With Plasma And Shock Produced By Pulsed Spark Discharge, Shomik Mukhopadhyay

Dissertations

Interactions of powders with high-temperature plasma and shockwaves occur in diverse scenarios, such as nuclear blasts, accidental industrial dust explosions, solid propellant combustion in explosive charges and when removing contaminants from surfaces. Electrostatic Discharge (ESD), known for generating shock and plasma, is a promising lab-scale technique for simulating these interactions. Studies with ESD involved placing powders near a spark-producing gap between electrodes and observing mechanical and chemical processes like particle motion and ignition. A limited range of spark conditions and material properties have been tested, which facilitated the development and validation of preliminary computational models describing this system. Significant gaps …

Bottling Automation System, Dylanie Tippit

Honors College Theses

This report details the complete design of an automated bottling system. Each bottle is 5.97 centimeters tall and has an outer diameter of 3.81 centimeters. The goal of the project is to successfully fill and cap twelve bottles in under three and a half minutes. The system will have two conveyors in series, a water dispenser, an electrolyte dispenser, capping station, Human Machine Interface (HMI) and Allen Bradley programmable logic controller (PLC). The water and electrolyte dispenser will have two ball valves in series, with the desired amount of volume to dispense the designated liquid. The capping station will be …

An Optimization Tool For A Standalone Photovoltaic System, Johanes Kasilima

Tanzania Journal of Engineering and Technology (TJET)

Stand-alone photovoltaic systems (SAPV) are often used in remote areas where access to grid electricity is limited. This system depends on solar energy. However, Photovoltaic (PV) systems need a greater initial investment than conventional sources of energy, and their effectiveness is reliant on a number of environmental conditions such as the unpredictable solar radiation. One step in reducing the investment cost of a PV system is determining the optimal size of solar PV components that minimize costs. This paper presents a Particle Swarm based optimization tool for sizing Stand-alone PV systems. The optimization tool selects the optimal Levelized Cost of …

Optimal Load Shedding During Service Restoration In Electrical Secondary Distribution Network Based On Reinforcement Learning, Rukia J. Mwifunyi

Tanzania Journal of Engineering and Technology (TJET)

Increased stress in traditional power systems results in blackouts due to voltage instability attributed to a mismatch between available capacity and load demand, especially in distribution networks. Service restoration schemes are designed to return power supply to the affected parts of the networks. The availability of insufficient supply is a complex problem that requires operational experience or an automatic system. The stochastic nature of load demand significantly impacts service restoration as it results in increased restored demand in case a fault occurs during off-peak hours and helps reduce overload if the fault occurs during peak hours. The study adopts an …

Design Of A Launchable Remote-Controlled Rover And Protective Aeroshell, Matthew Loewer, Colby Weeks, Lake Williams, Jackson Zazzaro

Senior Theses

Planetary rovers, vehicles that can traverse challenging terrain, have excelled in their exploration missions to other celestial bodies. They have been especially suitable for exploring Mars, as rovers such as Opportunity and Perseverance have collected valuable geological, atmospheric, seismic, and magnetic information from the Martian surface. Rovers will remain vital in future space exploration missions, and it is necessary to understand their design and functionality. This paper focuses on the design and prototyping of a miniature rover that can survive the rough Martian terrain while collecting and submitting environmental data for scientific analysis. The design is based off proven Martian …

Electophorectic Deposition For Novel Nanodecorated Electrodes Towards Thermally Charging Supercapacitor (Tcsc), Ashish Thakur

Mechanical and Aerospace Engineering Theses - Archive

Thermally Self-Charging Supercapacitors (TSCS) are a promising new technology that can harvest waste heat to produce electrical energy. The Soret effect is exploited wherein ion separation due a temperature gradient leads to a potential difference. Here, we use electrophoretic deposition (EPD), a room-temperature, scalable, universal technique, to obtain CNT decorated electrodes for fabrication of such TSCS devices with ionic liquid electrolyte. We further show that precise control over deposition parameters can be used for optimization of TSCS performance metrics. TSCS devices were tested by several characterization standards, indicating the superior performance of nanodecorated electrodes obtained by EPD.

Dueling Robot, Abigail Coy

All Undergraduate Projects

This project was undertaken as a personal challenge to combine a Mechanical Engineering Technology degree and an Electrical Engineering Technology degree into a single final project showing the cumulative knowledge gained. It was determined that a robot to participate in Western Allied Robotics would be designed and manufactured for the 3 lb. weight class.

A two-part power system was designed to provide more power to the weapon arm. This design combined a compressive spring’s kinetic energy with the torque from the electric motor. Research determined all of the purchased components required and analysis were performed to determine the geometry and …

Development And Application Of Guided Mode Resonance Biosensor Platforms For Highly Sensitive And Real-Time Cell Killing Assays, Seyedmohsen Vaziri

Electrical Engineering Dissertations - Archive

In this work, we developed and investigated the cancer cell killing efficacy of different instances using real-time high-sensitivity measurements facilitated by Guided-Mode Resonance (GMR) sensors. The GMR biosensor technology detects shifts in the spectral peak caused by changes in the refractive index of the surrounding medium, offering a label-free method for monitoring cellular events.

A549 cell line wild type and HER2 knockout (lung cancer cells) were exposed to different concentrations of Triton X-100 and ADC (Herceptin with αHFc-CL-DMDM). The GMR-based cell killing assay demonstrated exceptional sensitivity and specificity, with shifts in wavelength exhibiting a robust correlation with cell viability and …

Fabrication Of Smooth Sac305 Thin Film Via Magnetron Sputtering, M. Ojha, A. A. Elmustafa

Mechanical & Aerospace Engineering Faculty Publications

SAC305 (96.5 wt% Sn, 3 wt% Ag, 0.5 wt%Cu) solder is increasingly becoming popular due to its reliability good characteristics and performance in addition to the environmental concerns and regulations that restrict the use of lead in nano/microelectronic products. In nano/microelectronics, manufacturing smooth solder coatings free of defects such as voids and cracks, which can compromise joint reliability is crucial. Magnetron sputtering offers a high degree of control over film thickness and composition, resulting in films with excellent uniformity and adhesion. Despite these advantages, fabricating continuous and robust SAC305 films using magnetron sputtering remains a difficult task with limited research …

Functional Verification Of Additively Manufactured Metallopolymer Structures For Structural Electronics Design, Nathan D. Singhal

Honors Undergraduate Theses

As an attempt to improve the overall cost-effectiveness and ease of structural electronics manufacturing, this study characterizes the mechanical and electrical responses of structures which are fabricated from a novel metallopolymer composite material by fused deposition modeling as they are subjected to quasi-static, uniaxial mechanical tension. Baseline values of tensile properties and electrical resistivity were first obtained via ASTM D638-22 standard testing procedures and linear sweep voltammetry (LSV), respectively. A hybrid procedure to measure in-situ mechanically dependent electrical behavior was subsequently developed and implemented. The mechanical and electromechanical testing was followed by the derivation of stochastic values for several mechanical …

Isolation And Characterization Of Caffeine-Degrading Bacteria From Coffee Plantation Areas In Malaysia, Elvina Clarie Dullah, Mohd Fazli Farida Asras

Makara Journal of Technology

Decaffeination by microbial degradation is currently the most optimal and low-cost approach, involving only microbial cells and/or their enzymes. The bacterium was characterized using a series of biochemical tests. Positive results were obtained from carbohydrate fermentation, citrate utilization, and catalase tests, while negative results were obtained from Voges-Proskauer (VP) and indole tests. Three different caffeine concentrations of 0.25%, 0.4%, and 2% were tested and measured through Gas Chromatography-Mass Spectrophotometry (GC-MS) analysis. The highest caffeine reduction (89.25%) was found when 0.25% caffeine was used in the media. Only a small amount of caffeine was reduced to 0.4% and 2%, with 34.78% …

Optimization Of The Building Envelope And Roof Shading To Reduce The Energy Consumption Of College Low-Rise Buildings In Indonesia, Nasruddin Nasruddin, Azimil Gani Alam, Mohammad Imroz Sohel

Makara Journal of Technology

Energy consumption in buildings is a crucial concern globally, prompting researchers to explore innovative solutions to mitigate its impact. This study investigates the optimization of building envelopes and roof shading systems of existing buildings in Indonesia to realize notable energy savings. Multiple scenarios were explored, with modifications to building envelopes and roof shading, highlighting the overall thermal transfer value as a key parameter. Using EnergyPlus simulations, the efficacy of natural ventilation in corridors and roof shading modifications was assessed in reducing energy consumption. The findings revealed that renovating existing buildings by optimization of the building envelope and roof shading by …

Design, Fabrication And Characterization Of Zero Power Sensor/Harvester For Smart Grid Applications, Zeynel Guler

Mechanical Engineering ETDs

This study presents a flexible sensor/harvester device to be used in both electromagnetic sensing and energy harvesting applications for smart grids. When a current passes through a wire, the sensor detects the magnetic field created by that current. The sensor magnet interacts with the wire magnetic field resulting in a transfer of energy through the piezoelectric cantilever. Piezoelectric, conductive, magnetic, and magnetostrictive composite thin films were prepared to fabricate this device.

Initially, the magnet of the cantilever was optimized considering its shape, thickness, length, taper angle etc. via both simulations and experiments. Peak to peak voltage versus cantilever position graph …

Project Thetis: A Low-Cost, Low-Profile Inertial Data Logger, Braidan Duffy

Theses and Dissertations

This thesis details the design, testing, calibration, and verification of a nine degree of freedom inertial measurement data logger for use with floating bodies. The instrument was conceived to address limitations of equipment used in classes within the Ocean Engineering department at Florida Institute of Technology. By meeting with several stakeholders and end users, a series of stakeholder requirements, capabilities, and component-level requirements were de- veloped that informed the design constraints. There were several hardware iterations of the board, culminating in Revision F5 which was extensively tested and proven. The design was inspected after testing concluded to determine which capabilities …

Gpu Based Monte Carlo Estimation Of Eddy Current Losses In Electromagnetic Coil-Core System, Adwaith Ravichandran

Theses and Dissertations

A novel parallelizable probabilistic approach to model eddy currents in AC electromagnets is presented in this research. Consequently, power loss associated with the formation of these eddy currents is estimated and validated using experimental data. Furthermore, predicting the effect of ferromagnetic alternating field enhancement on power loss in the source excitation winding has been an active area of research. Unlike a stationary field, an alternating sinusoidal field diffuses partially into the ferromagnetic material leading to a predictably sub-optimal field enhancement. To model these physics, finite element techniques employ nonlinear iterative solvers which are time consuming. A novel method is developed …

Investigating Mems Devices In Flow Conditions Relevant To Flow-Through Systems., Mohammad Shafquatul Islam

Electronic Theses and Dissertations

Advancements in microscale actuating technologies has substantially expanded the possibilities of interacting with the surrounding environment. Microstructures that deflect in response to mechanical forces are one of the largest application areas of microelectromechanical systems (MEMS). MEMS devices, functioning as sensors, actuators, and support structures, find applications in inertial sensors, pressure sensors, chemical sensors, and robotics, among others. Driven by the critical role of catalytic membrane reactors, this dissertation aims to evaluate enzyme activity on polymeric membranes and explore how fabrication methods from the field of Electrical and Computer Engineering (ECE) can incorporate sensing and actuation into these porous surfaces. Toward …