Open Access. Powered by Scholars. Published by Universities.®

Electrical and Electronics Commons™

Open Access. Powered by Scholars. Published by Universities.®

Materials Science and Engineering

Institution
Keyword
Publication Year
Publication
Publication Type

Articles 241 - 270 of 567

Full-Text Articles in Electrical and Electronics

Group Decisions In Value Management, Christiono Utomo, Farida Murti, Arazi Idrus Apr 2015

Group Decisions In Value Management, Christiono Utomo, Farida Murti, Arazi Idrus

Makara Journal of Technology

This research deals with a technique to expedite group decision making during the selection of technical solutions for value management process. Selection of a solution from a set of alternatives is facilitated by evaluating using multicriteria decision making techniques. During the process, every possible solution is rated on criteria of function and cost. Function deals more with quality than with quantity, and cost can be calculated based on the theoretical time value of money. Decision-making techniques based on satisfying games are applied to determine the relative function and cost of solutions and hence their relative value. The functions were determined …

Go to article

Seebeck Coefficient Of Soi Layer Induced By Phonon Transport, Faiz Salleh, Takuro Oda, Yuhei Suzuki, Yoshinari Kamakura, Hiroya Ikeda Apr 2015

Seebeck Coefficient Of Soi Layer Induced By Phonon Transport, Faiz Salleh, Takuro Oda, Yuhei Suzuki, Yoshinari Kamakura, Hiroya Ikeda

Makara Journal of Technology

The Seebeck coefficient of a patterned Si wire on P-doped SOI (Si-on-insulator) layer with a carrier concentration of 1018 cm-3 was measured near room temperature. The Seebeck coefficient is found to be smaller than that in the SOI layer and to be closer to the calculated Seebeck coefficient including the electronic contribution. The decrease in the Seebeck coefficient of Si wire is likely to occur due to the elimination of the contribution of phonon drag part. From the theoretical calculation of scattering rates by considering the scattering processes in phonon system, it is considered that an increase in phonon-boundary scattering …

Go to article

Construction Of A Novel Method Of Measuring Thermal Conductivity For Nanostructures, Hiroya Ikeda, Shoma Yoshida, Yuhei Suzuki, Veerappan Manimuthu, Faiz Salleh, Fujio Kuwahara, Masaru Shimomura, Kenji Murakami Apr 2015

Construction Of A Novel Method Of Measuring Thermal Conductivity For Nanostructures, Hiroya Ikeda, Shoma Yoshida, Yuhei Suzuki, Veerappan Manimuthu, Faiz Salleh, Fujio Kuwahara, Masaru Shimomura, Kenji Murakami

Makara Journal of Technology

With the aim of characterizing the thermal conduction in a nanometer-scaled materials, we have constructed a novel method on the basis of an ac calorimetric method. In this method, periodic sample heating is performed by light irradiation and the corresponding periodic temperature is detected by infrared irradiative thermometer. This makes us measure the thermal diffusivity out of contact with the objective sample. In the present study, we confirm to measure the thermal diffusivity of bulk Si and Cu by this non-contact method with halogen-lamp irradiation. In determining the thermal diffusivity from the relationship between distance deviation and delay time, the …

Go to article

Phonon-Drag Contribution To Seebeck Coefficient Of Ge-On-Insulator Substrate Fabricated By Wafer Bonding Process, Veerappan Manimuthu, Shoma Yoshida, Yuhei Suzuki, Faiz Salleh, Mukannan Arivanandhan, Yoshinari Kamakura, Yasuhiro Hayakawa, Hiroya Ikeda Apr 2015

Phonon-Drag Contribution To Seebeck Coefficient Of Ge-On-Insulator Substrate Fabricated By Wafer Bonding Process, Veerappan Manimuthu, Shoma Yoshida, Yuhei Suzuki, Faiz Salleh, Mukannan Arivanandhan, Yoshinari Kamakura, Yasuhiro Hayakawa, Hiroya Ikeda

Makara Journal of Technology

In order to build high-sensitivity infrared photodetectors using SiGe nanowires, we investigate the thermoelectric characteristics of Ge-on-insulator (GOI) layers as a reference for SiGe. We fabricate p-type GOI substrates with an impurity concentration of 1016-1018cm-3 by a wafer-bonding process using Ge and oxidized Si wafers. Annealing treatment is performed in order to further increase the bonding strength of Ge/SiO2 interface. We measure the Seebeck coefficient in the temperature range of 290-350 K. The Seebeck coefficient of the GOI layers is very close to the theoretical value for Ge, calculated on the basis of carrier transport. Hence, there is a small …

Go to article

Fiber Optic Ring Resonator Sensor Detection Technique Based On Spectral Intensity Integration, Purnomo Sidi Priambodo, Sasono Rahardjo, Gunawan Witjaksono, Djoko Hartanto Apr 2015

Fiber Optic Ring Resonator Sensor Detection Technique Based On Spectral Intensity Integration, Purnomo Sidi Priambodo, Sasono Rahardjo, Gunawan Witjaksono, Djoko Hartanto

Makara Journal of Technology

Resonant field phenomenon in optical ring resonator has been a major theme for various studies and can be used for various sensor applications. The spectral response shape changes are subjects to be discussed and analyzed for detection in optical sensor system. The spectral response changes are caused by various factors ranging from refractive index of the surrounding medium, medium loss due to absorption and scattering, and coupling variation between waveguides. These optical phenomena are mostly used for bio-sensor applications, since it is free from electromagnetic interference (EMI) and non-physically destructive. In this paper, we discuss our current research in developing …

Go to article

The Effects Of The Types Of Milk (Cow, Goat, Soya) And Enzymes (Rennet, Papain, Bromelain) Toward Cheddar Cheese Production, Ariestya Arlene, Anastasia Prima Kristijarti, Ivana Ardelia Apr 2015

The Effects Of The Types Of Milk (Cow, Goat, Soya) And Enzymes (Rennet, Papain, Bromelain) Toward Cheddar Cheese Production, Ariestya Arlene, Anastasia Prima Kristijarti, Ivana Ardelia

Makara Journal of Technology

The objectives of this research are to study the effects of different types of milk and enzymes toward the yield and quality (moisture, ash, protein, fat content, and texture) of cheddar cheese and the interaction between those two variables during the process. The types of milk are cow, goat, and soya milk, while the types of enzymes are rennet, papain, and bromelain enzymes. Regarding the procedure, the milk is first pasteurized before CaCl2 and Lactobacillus lactis that acts as the acidifier starter as much as 0.2% (w/v) and 0.5% of the milk volume are added respectively. The amount of enzyme …

Go to article

Hazard-Driven Drivers’ Behaviours Towards Vehicle-To-Median Safe Distances, Martha Leni Siregar Apr 2015

Hazard-Driven Drivers’ Behaviours Towards Vehicle-To-Median Safe Distances, Martha Leni Siregar

Makara Journal of Technology

A median is required for a two-way road to separate traffic from opposing lanes and to prevent head-on collisions. However, studies indicate that medians are also perceived as hazards which need to be avoided during driving. This hazard perception is manifested in drivers’ changing behavior towards various types of medians along the driving lanes inform of their tendency to allow various safe distances to the medians. The Indonesian Highway Capacity Manual (IHCM) does not differentiate between types of medians and the influence on the drivers’ choice of safe margin to the medians. Therefore, this study looks into how the existence …

Go to article

Energy And Exergy Analysis Of Kalina Cycle For The Utilization Of Waste Heat In Brine Water For Indonesian Geothermal Field, Nasruddin Nasruddin, Agus Noor Sidiq, Abdulmajeed Mohamad, Rama Usvika Apr 2015

Energy And Exergy Analysis Of Kalina Cycle For The Utilization Of Waste Heat In Brine Water For Indonesian Geothermal Field, Nasruddin Nasruddin, Agus Noor Sidiq, Abdulmajeed Mohamad, Rama Usvika

Makara Journal of Technology

The utilization of waste heat in a power plant system—which would otherwise be released back to the environment—in order to produce additional power increases the efficiency of the system itself. The purpose of this study is to present an energy and exergy analysis of Kalina Cycle System (KCS) 11, which is proposed to be utilized to generate additional electric power from the waste heat contained in geothermal brine water available in the Lahendong Geothermal power plant site in North Sulawesi, Indonesia. A modeling application on energy and exergy system is used to study the design of thermal system which uses …

Go to article

Study Of Millisecond Laser Annealing On Ion Implanted Soi And Application To Scaled Finfet Technology, Tyler J. Michalak Jan 2015

Study Of Millisecond Laser Annealing On Ion Implanted Soi And Application To Scaled Finfet Technology, Tyler J. Michalak

Legacy Theses & Dissertations (2009 - 2024)

The fabrication of metal-oxide-semiconductor field effect transistors (MOSFET) requires the engineering of low resistance, low leakage, and extremely precise p-n junctions. The introduction of finFET technology has introduced new challenges for traditional ion implantation and annealing techniques in junction design as the fin widths continue to decrease for improved short channel control. This work investigates the use of millisecond scanning laser annealing in the formation of n-type source/drain junctions in next generation MOSFET.

Go to article

Implementation Of Strategies To Improve The Reliability Of Iii-Nitride Photodetectors Towards The Realization Of Visible And Solar-Blind Imaging Arrays, John Bulmer Jan 2015

Implementation Of Strategies To Improve The Reliability Of Iii-Nitride Photodetectors Towards The Realization Of Visible And Solar-Blind Imaging Arrays, John Bulmer

Legacy Theses & Dissertations (2009 - 2024)

Ultraviolet (UV) radiation detectors are being heavily researched for applications in non-line-of-sight (NLOS) communication systems, flame monitoring, biological detection, and astronomical studies. These applications are currently being met by the use of Si-based photomultiplier tubes (PMTs), which are bulky, fragile, expensive and require the use of external filters to achieve true visible-blind and solar-blind operation.

Go to article

High Frequency Signal Transmission In Through Silicon Via Based 3d Integrated Circuit, Min Xu Jan 2015

High Frequency Signal Transmission In Through Silicon Via Based 3d Integrated Circuit, Min Xu

Legacy Theses & Dissertations (2009 - 2024)

Through silicon vias (TSVs) enable 3-dimensional (3D) integrated circuits (ICs), which have the potential to reduce the power consumption, interconnect length and overall communication latency in modern nanoelectronics systems. High-speed signal transmission channels through stacked silicon substrates are critical for 3D heterogeneous integration. This work presents systematic analyses of fabricated 3D IC test structures. This includes test structure design, fabrication, experimental characterization, equivalent circuit modeling and full wave simulations for high-speed signal transmission of the TSV based 3D IC channels.

Go to article

Carbon 1d/2d Nanoelectronics : Integration And Device Applications, Zhaoying Hu Jan 2015

Carbon 1d/2d Nanoelectronics : Integration And Device Applications, Zhaoying Hu

Legacy Theses & Dissertations (2009 - 2024)

Graphene is a one-atom thick planar monolayer of sp2-bonded carbon atoms organized in a hexagonal crystal lattice. A single walled carbon nanotube (CNT) can be thought of as a graphene sheet rolled up into a seamless hollow cylinder with extremely high length-to-diameter ratio. Their ultra-thin body, large surface area, and exceptional electronic, optical and mechanical properties make these low-dimensional carbon materials ideal candidates for electronic applications. However, adopting low-dimensional carbon materials into semiconductor industry faces significant material and integration challenges. There is an urgent need for research at fundamental and applicative levels to find a roadmap for carbon nanomaterial to …

Go to article

The Ph Sensing Properties Of Rf Sputtered Ruo2 Thin-Film Prepared Using Different Ar/O2 Flow Ratio, Ali Sardarinejad, Devendra Kumar Maurya, Kamal Alameh Jan 2015

The Ph Sensing Properties Of Rf Sputtered Ruo2 Thin-Film Prepared Using Different Ar/O2 Flow Ratio, Ali Sardarinejad, Devendra Kumar Maurya, Kamal Alameh

Research outputs 2014 to 2021

The influence of the Ar/O2 gas ratio during radio frequency (RF) sputtering of the RuO2 sensing electrode on the pH sensing performance is investigated. The developed pH sensor consists in an RF sputtered ruthenium oxide thin-film sensing electrode, in conjunction with an electroplated Ag/AgCl reference electrode. The performance and characterization of the developed pH sensors in terms of sensitivity, response time, stability, reversibility, and hysteresis are investigated. Experimental results show that the pH sensor exhibits super-Nernstian slopes in the range of 64.33-73.83 mV/pH for Ar/O2 gas ratio between 10/0-7/3. In particular, the best pH sensing performance, in …

Go to article

3d Printing, Open-Source Technology And Their Applications In Research, Chenlong Zhang Jan 2015

3d Printing, Open-Source Technology And Their Applications In Research, Chenlong Zhang

Dissertations, Master's Theses and Master's Reports

Open-source software received tremendous success as it drives down the cost of software and expand the distribution. Open-source hardware, as part of the open-source movement, has just risen into public attention for its potential to further drive down the cost of all kinds of manufacturing goods and reshape the manufacture chain. In this report we explores the history, development and the future of open-source hardware project, summarizing the opportunities, challenges and possible solutions. 3D printing is demonstrated as a booster to assist open-source hardware’s development. Low-cost 3D printer enables at-home and in-time fabrication, the download-print-use-improve-distribute cycle is established to encourage …

Go to article

Design Of Gan-Based Low-Loss Y-Branch Power Splitter, Retno Wigajatri Purnamaningsih, Irma Saraswati, Nji Raden Poespawati, Elhadj Dogheche Dec 2014

Design Of Gan-Based Low-Loss Y-Branch Power Splitter, Retno Wigajatri Purnamaningsih, Irma Saraswati, Nji Raden Poespawati, Elhadj Dogheche

Makara Journal of Technology

We present a Y-branch power splitter design with a multimode section using GaN on Sapphire at telecommunication wavelength. The GaN sample optical properties were also investigated, resulting in a refractive index for the GaN layers nTE=2.289±0.001 and nTM=2.324±0.00. Optimization of the structure parameters for this structure was conducted accurately using BPM methods. The results demonstrated the possibility of realizing a GaN-based Y-branch power splitter for various applications.

Go to article

Ultra-Wideband Notched Characteristic Fed By Coplanar Waveguide, Rastanto Hadinegoro, Yuli Kurnia Ningsih, Indra Surjati Dec 2014

Ultra-Wideband Notched Characteristic Fed By Coplanar Waveguide, Rastanto Hadinegoro, Yuli Kurnia Ningsih, Indra Surjati

Makara Journal of Technology

In this paper, a novel Ultra-Wide Band (UWB) notch patch antenna with co-planar waveguide (CPW) fed is presented. This antenna only used one layer and the patch antenna is constructed on the first layer and back to back with CPW fed and bottom part is ground plane. The width notch is used to achieve the UWB characteristic. The results shown that the impedance bandwidth is 1130 MHz (1.662–2.792 GHz) or about 50.7% for VSWR <2.

Go to article

Analysis Of Vibration Generated By The Rubbing Of Flat Surfaces, Zahrul Fuadi Dec 2014

Analysis Of Vibration Generated By The Rubbing Of Flat Surfaces, Zahrul Fuadi

Makara Journal of Technology

Among the phenomena that occur as a result of contact between two surfaces is friction sound, in which surface roughness is of great importance. In this study, the parameter of contact stiffness is used to explain the frequency characteristic of vibration generated by the rubbing of flat surfaces under a small load. A 3-disk configuration rubbing method was used, which provides a unique characteristic of the system's frequency response function containing specific information about the rubbing vibrations. It is shown that the peak frequency of the rubbing vibration can be explained by using a two-degrees-of-freedom model incorporating the parameter of …

Go to article

Endoscopic Application Of A Compact Compound-Eye Camera, Keiichiro Kagawa, Shoji Kawahito Dec 2014

Endoscopic Application Of A Compact Compound-Eye Camera, Keiichiro Kagawa, Shoji Kawahito

Makara Journal of Technology

A multi-functional compound-eye endoscope enabling multi-spectral imaging and variable field-of-view is presented, which is based on a compact compound-eye camera called TOMBO (thin observation module by bound optics). Narrow-band filters attached to some lenses provide snap-shot multi-band images. Fixed and movable mirrors are introduced to control the field of view, which realizes several observation modes such as three-dimensional shape measurement, wide field-of-view, and close-up observation.

Go to article

Development Of The Soekarno–Hatta International Airport Rail Link Project Using The Value Engineering Method: Creating Value For Money, Mohammed Ali Berawi, Bambang Susantono, Suyono Dikun, Tommy Ilyas, Herawati Zetha Rahman, Abdur Rohim Boy Berawi, Teuku Yuri Zagloel, Perdana Miraj, Jade Sjafrecia Petroceany Dec 2014

Development Of The Soekarno–Hatta International Airport Rail Link Project Using The Value Engineering Method: Creating Value For Money, Mohammed Ali Berawi, Bambang Susantono, Suyono Dikun, Tommy Ilyas, Herawati Zetha Rahman, Abdur Rohim Boy Berawi, Teuku Yuri Zagloel, Perdana Miraj, Jade Sjafrecia Petroceany

Makara Journal of Technology

Soekarno–Hatta Airport is the main gateway for international flights to Greater Jakarta. Its accessibility depends on the inter-city and Sedyatmo toll roads, which causes congestion in peak hours, leading to uncertainty about travel times. The Soekarno–Hatta International Airport Rail Link (SHIARL) is proposed as an alternative mass transportation project, which is expected to provide accessibility and mobility for people and goods to and from the airport. Previously, the project was unattractive to private investors as it was technically and financially unfeasible. Therefore, this research aims to improve the feasibility of the Soekarno-Hatta International Airport Rail Link (SHIARL) by using a …

Go to article

The Mechanical And Tribology Properties Of Sputtered Titanium Aluminum Nitride Coating On The Tungsten Carbide Insert Tool In The Dry Turning Of Tool Steel, Esmar Budi, Mohd. Razali Bin Muhamad, Md. Nizam Bin Abdul Rahman Dec 2014

The Mechanical And Tribology Properties Of Sputtered Titanium Aluminum Nitride Coating On The Tungsten Carbide Insert Tool In The Dry Turning Of Tool Steel, Esmar Budi, Mohd. Razali Bin Muhamad, Md. Nizam Bin Abdul Rahman

Makara Journal of Technology

The effect of the sputtering parameters on the mechanical tribology properties of Titanium Aluminum Nitride coating on the tungsten cabide insert tool in the dry turning of tool steel has been investigated. The coating was deposited using a Direct Current magnetron sputtering system with various substrate biases (-79 to -221 V) and nitrogen flow rates (30 to 72 sccm). The dry turning test was carried out on a Computer Numeric Code machine using an optimum cutting parameter setting. The results show that the lowest flank wear (~0.4 mm) was achieved using a Titanium Aluminum Nitride-coated tool that was deposited at …

Go to article

Modified Design Of Pin-On-Ring Tribometer For Hip Joint Prostheses Measurement; Case Study On Salat Activity, Muhammad Khafidh, Jamari Jamari, Sulardjaka Sulardjaka, Mohamad Tauviqirrahman, Emile Van Der Heide Dec 2014

Modified Design Of Pin-On-Ring Tribometer For Hip Joint Prostheses Measurement; Case Study On Salat Activity, Muhammad Khafidh, Jamari Jamari, Sulardjaka Sulardjaka, Mohamad Tauviqirrahman, Emile Van Der Heide

Makara Journal of Technology

Total hip replacement (THR) is one of the most successful orthopedic surgical procedures for replacing a broken hip joint. In THR, wear may occur at the articulating surface of the acetabular cup and the femoral head. In Indonesia, the country with the largest Muslim population in the world, most of the inhabitants do salat (praying) every day. THR users are banned from doing salat for fear it will damage the hip joint prostheses. The previous wear calculation methods on the hip joint prostheses use the gravimetric, coordinate measuring machine (CMM), profiler, and geometric method. The disadvantages of the previous methods …

Go to article

Continuous Production Of Nanotubes And Carbon Clusters By Use Of The Revolver-Injection-Type Arc Jet Producer, Tetsu Mieno, Naoki Matsumoto, Takahashi Tomie, H. Inoue Dec 2014

Continuous Production Of Nanotubes And Carbon Clusters By Use Of The Revolver-Injection-Type Arc Jet Producer, Tetsu Mieno, Naoki Matsumoto, Takahashi Tomie, H. Inoue

Makara Journal of Technology

Efficient and continuous production of fullerenes, single-walled carbon nanotubes (SWNTs), and carbon nano-particles has been developed by the JxB arc jet method, where the Lorentz force of magnetic field jets out gaseous carbon particles to the JxB direction. In order to realize continuous mass production of these carbon clusters, the revolverinjection- type arc jet producer (RIT-AJP) has been developed. Production of fullerenes, endohedral metallo-fullerenes, SWNTs, metal-encapsulated carbon nano particles has been examined.

Go to article

Lateral Load Resistance Of Laminated Veneer Lumber Sengonwooden Joints With Wooden Dowels, Niken Palaeowati, Ali Awaludin, Suprapto Siswosukarto Dec 2014

Lateral Load Resistance Of Laminated Veneer Lumber Sengonwooden Joints With Wooden Dowels, Niken Palaeowati, Ali Awaludin, Suprapto Siswosukarto

Makara Journal of Technology

Analytical models for wooden-doweled joints need to be developed. The objective of this research is to determine whether the strength of wooden-doweled joints can be well predicted by equations developed for steel-doweled joints. In this experiment, various connection parameters, such as dowel diameter, species of the wooden dowel, and angle of joints, are studied. The joint specimens are loaded in a quasi-static state with four replications each. A5% offset diameter method is used to determine the lateral load resistance of the tested joints, while the predictions are evaluated by equations given in Indonesian National Standard (SNI) 7973-2013 and the European …

Go to article

Gesn Light-Emitting Devices, Yiyin Zhou Dec 2014

Gesn Light-Emitting Devices, Yiyin Zhou

Graduate Theses and Dissertations

Silicon based optoelectronic devices have been investigated for decades. However, due to the indirect band gap nature of Si and Ge, developing of efficient light-emitting source on Si is still a challenging topic. GeSn based optoelectronic devices have the great potential to overcome this deficiency for several reasons. By adding more fraction of Sn into Ge, GeSn band gap could be reduced. The narrowed band gap could be developed for near to mid infrared applications. The alloy can even become the direct band gap material with a large Sn composition (beyond 8%). This feature could enhance the light emission from …

Go to article

Metal Assisted Nanowire Growth For Silicon Nanowire/Amorphous Silicon Composite Solar Cell, Asmaa Ali Sadoon Dec 2014

Metal Assisted Nanowire Growth For Silicon Nanowire/Amorphous Silicon Composite Solar Cell, Asmaa Ali Sadoon

Graduate Theses and Dissertations

Solar cells are photovoltaic devices that convert the energy of light to electricity by the photovoltaic effect. Crystalline silicon-based solar cells are the most dominant solar cells in the market today due to the high efficiency and relatively low cost. However, the cost of such solar cell is still high due to the large amount of material that is consumed in fabricating such a device. Polycrystalline/amorphous thin films and nanomaterial technologies have emerged to reduce the high cost of c-Si based solar cells and increase the efficiency. In this research, we combined these two technologies to propose and fabricate silicon …

Go to article

Adjustable Resonance Frequency Of Rf-Mems Capacitor By Using Comb- Drive Actuators: A Design Approaches, Agus Santoso Tamsir, Sandy Tannu Wijaya, Dato’ Burhanuddin Yeop Majlis Aug 2014

Adjustable Resonance Frequency Of Rf-Mems Capacitor By Using Comb- Drive Actuators: A Design Approaches, Agus Santoso Tamsir, Sandy Tannu Wijaya, Dato’ Burhanuddin Yeop Majlis

Makara Journal of Technology

The needs of smaller size RF varactor is a must today, and MEMS comes to be the potential one. In this paper we proposed an adjustable resonance RF-MEMS varactor by using comb-drive actuators placing in each side of the square movable plate. In our preliminary simulation, we found that the device can work properly but some constraints comes such as the dominancies of harmonic resonance frequencies that influences into the nominal capacitances. Therefore for the next step of development we have to find out the window of the structural dimension for a certain spans and a certain operating frequencies.

Go to article

Make Or Buy Analysis Model Based On Tolerance Design To Minimize Manufacturing Cost And Quality Loss, Cucuk Nur Rosyidi, Reza Rizkichani Akbar, Wakhid Ahmad Jauhari Aug 2014

Make Or Buy Analysis Model Based On Tolerance Design To Minimize Manufacturing Cost And Quality Loss, Cucuk Nur Rosyidi, Reza Rizkichani Akbar, Wakhid Ahmad Jauhari

Makara Journal of Technology

In a manufacturing company, manufacturing costs, or component prices, and tolerance will affect the price and the quality of a product. Companies must produce high-quality products with low manufacturing costs in order to keep their products competitive in the market; however, it is difficult to produce a high-quality product with a low manufacturing cost. Companies have difficulties in determining the components to be produced using their own manufacturing facilities (make) or outsourced to their suppliers (buy). Hence, a make or buy analysis is needed to minimize the manufacturing costs and quality loss and to determine the optimum alternative regarding make …

Go to article

Observation Of Tunneling Effects In Lateral Nanowire Pn Junctions, Sri Purwiyanti, Arief Udhiarto, Daniel Moraru, Takeshi Mizuno, Djoko Hartanto, Michiharu Tabe Aug 2014

Observation Of Tunneling Effects In Lateral Nanowire Pn Junctions, Sri Purwiyanti, Arief Udhiarto, Daniel Moraru, Takeshi Mizuno, Djoko Hartanto, Michiharu Tabe

Makara Journal of Technology

As electronic device dimensions are continuously reduced, applied bias conditions significantly change and the transport mechanisms must be reconsidered. Tunneling devices are promising for scaled-down electronics because of expected high-speed operation and relatively low bias. In this work, we investigated the tunneling features in silicon-oninsulator lateral nanowire pn junction and pin junction devices. By controlling the substrate voltage, tunneling features can be observed in the electrical characteristics. We found that the minimum substrate voltage required for tunneling to occur in pn junctions is higher as compared with pin junctions. The main cause of these effects relies in the difference between …

Go to article

Argon Ion Irradiation Effect On The Magnetic Properties Of Fe-Al2o3 Nano Granular Film, Setyo Purwanto, Isao Sakamoto Aug 2014

Argon Ion Irradiation Effect On The Magnetic Properties Of Fe-Al2o3 Nano Granular Film, Setyo Purwanto, Isao Sakamoto

Makara Journal of Technology

We studied the effect of Argon (Ar) ion irradiation on Fe-Al2O3 nanogranular thin film. X-ray diffraction (XRD) patterns show that the ion dose might promote the growth of the Fe2O3 phase from an amorphous phase to a crystalline phase. The magnetic and magnetoresistance properties were investigated using a vibrating sample magnetometer (VSM) and a four point probe (FPP). The results suggest that percolation concentration occurred at the 0.55 Fe volume fraction and with a maximum magnetoresistance (MR) ratio of 3%. The present MR ratio was lower than that of previous results, which might be related to the existence of the …

Go to article

Digestibility Of Betung Bamboo Fiber Following Fungal Pretreatment, Widya Fatriasari, Wasrin Syafii, Nyoman J. Wistara, Khaswar Syamsu, Bambang Prasetya Aug 2014

Digestibility Of Betung Bamboo Fiber Following Fungal Pretreatment, Widya Fatriasari, Wasrin Syafii, Nyoman J. Wistara, Khaswar Syamsu, Bambang Prasetya

Makara Journal of Technology

This research evaluated the effect of fungal pretreatment of betung bamboo fibers and enzymatic- and microwaveassisted hydrolysis on the reducing sugar yield. The enzymatic hydrolysis of the pretreated biomass was carried out with cellulase and 10 and 20 FPU/g of substrate in a shaking incubator at 50 °C and 150 rpm for 48 h. The sulfuric acid concentration used in the microwave-assisted acid hydrolysis was 1.0, 2.5, and 5%, either with or without the addition of activated carbon. Microwave irradiation (330 Watt) was applied for 5–12.5 min. The yield of reducing sugar was better with the microwave-assisted acid hydrolysis, and …

Go to article

First Prev Next Last