Electrical and Electronics Commons^™

Smart Nails For Lithium-Ion Battery Internal Short Circuit And Thermal Runaway Characterization, Mary Kate Long, Siyi Liu

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

Development Of Fiber-Optic High-Temperature Heat Flux Sensors For Venus Exploration, Sara Mog

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

Possibilities And Challenges Of Radio Frequency Energy Harvesting In Dar Es Salaam, Tanzania, Fredrick Isingo

Tanzania Journal of Engineering and Technology (TJET)

This paper presents investigation on the possibilities and challenges of harvesting ambient Radio Frequency Energy (RFE) at Dar es Salaam region in Tanzania. The Radio Frequency (RF) signals were measured using a Rohde and Schwarz FSC 3 spectrum analyzer observing available frequencies with their respective power. Among several RF signals received, the most powerful signals observed were; 800 MHz, 950 MHz, 2100 MHz and 2400 MHz, having average signal strengths of about-30.29 dBm,-35.94 dBm,-42.90 dBm and-30.42 dBm respectively. The power possessed within these frequencies were suitable to be harvested due to their signal strengths, an overall power average of-34.89dBm was …

A Bibliometric Survey On Ultra Wideband Multiple Input Multiple Output Antenna With Improved Isolation, Laxmikant K. Shevada, Hema D. Raut, Rajeshwari R. Malekar, Amruta S. Dixit, Sumit Kumar

Library Philosophy and Practice (e-journal)

Ultra wideband (UWB) technology remains a viable choice for very high speed data communication in future applications involving large bandwidth. For boosting the data communication efficiency and to mitigate the multipath fading issue faced by UWB system with existing narrowband systems, Multiple Input Multiple Output (MIMO) antenna system is used along with UWB. Mutual coupling which must be smaller in value plays a vital role in deciding the efficiency of MIMO antenna and hence it becomes as important aspect. The mutual coupling reduction techniques of various UWB MIMO antennas are surveyed in this bibliometric paper. The bibliometric survey aims to …

Design, Fabrication, And Reliability Effects Of Additively Manufactured First Level Compliant Interconnects For Microelectronics Application, Tumininu David Olatunji

Graduate Theses and Dissertations

Semiconductor packaging and development is greatly dependent on the magnitude of interconnect and on-chip stress that ultimately limits the reliability of electronic components. Thermomechanical related strains occur because of the coefficient of thermal expansion mismatch from different conjoined materials being assembled to manufacture a device. To curb the effect of thermal expansion mismatch between conjoined parts, studies have been done in integrating compliant structures between dies, solder balls, and substrates. Initial studies have enabled the design and manufacturing of these structures using a photolithography approach which involves a high number of fabrication steps depending on the complexity of the structures …

Design Of A 350 Kw Silicon Carbide Based 3-Phase Inverter With Ultra-Low Parasitic Inductance, Matthew Feurtado

Graduate Theses and Dissertations

The objective of this thesis is to present a design for a low parasitic inductance, high power density 3-phase inverter using silicon-carbide power modules for traction application in the electric vehicles with a power rating of 350 kW. With the market share of electric vehicles continuing to grow, there is a great opportunity for wide bandgap semiconductors such as silicon carbide (SiC) to improve the efficiency and size of the motor drives in these applications. In order to accomplish this goal, careful design and selection of each component in the system for optimum performance from an electrical, mechanical, and thermal …

Growth And Characterization Of Semiconductor Materials And Devices For Extreme Environments Applications, Abbas Sabbar

Graduate Theses and Dissertations

Numerous industries require electronics to operate reliably in harsh environments, such as extreme high temperatures (HTs), low temperature (LT), radiation rich environments, multi-extreme, etc. This dissertation is focused on two harsh environments: HT and multi-extreme.

The first study is on HT optoelectronics for future high-density power module applications. In the power modules design, galvanic isolation is required to pass through the gate control signal, reject the transient noise, and break the ground loops. The optocoupler, which consists of a lighting emitting diode (LED) and photodetector (PD), is commonly used as the solution of galvanic isolation at room temperatures. There is …

Novel Memristor Based True Random Number Generator, Scott Stoller

Boise State University Theses and Dissertations

Random numbers are an important, but often overlooked part of the modern computing environment. They are used everywhere around us for a variety of purposes, from simple decision making in video games such as a coin toss, to securing financial transactions and encrypting confidential communications. They are even useful for gambling and the lottery.

Random numbers are generated in many ways. Pseudo random number generators (PRNGs) generate numbers based on a formula. True random number generators (TRNGs) capture entropy from the environment to generate randomness. As our society and our devices become more connected in the digital world, it is …

Simulation Of An Sp8t 18 Ghz Rf Switch Using Smt Pin Diodes, Andre De Souza Vigano

Master's Theses

Radio frequency (RF) and microwave switches are widely used in several different applications including radar, measurement systems, telecommunications, and other areas. An RF switch can control a radar’s transmit vs. receive mode, select the operating band, or direct an RF signal to different paths. In this study, a single pole eight throw (SP8T) switch using only Surface Mount (SMT) components is designed and simulated in Keysight’s Advanced Design System (ADS). Single pole eight throw is defined as one input and eight possible outputs. A star network configuration with series-shunt PIN diode switches is used to create the 8-way RF switch. …

High-Temperature Optoelectronic Device Characterization And Integration Towards Optical Isolation For High-Density Power Modules, Syam Madhusoodhanan

Graduate Theses and Dissertations

Power modules based on wide bandgap (WBG) materials enhance reliability and considerably reduce cooling requirements that lead to a significant reduction in total system cost and weight. Although these innovative properties lead power modules to higher power density, some concerns still need to be addressed to take full advantage of WBG-based modules. For example, the use of bulky transformers as a galvanic isolation system to float the high voltage gate driver limits further size reduction of the high-temperature power modules. Bulky transformers can be replaced by integrating high-temperature optocouplers to scale down power modules further and achieve disrupting performance in …

A New Method Of Statcom Controlling For Harmonic Mitigation And Power Factor Correction, Doha Jdeed

Journal of the Arab American University مجلة الجامعة العربية الامريكية للبحوث

This paper presents a control algorithm of 3ph STATic synchronous COMpensator (STATCOM). The algorithm depends on the accurate reference currents extraction from only the nonlinear load current spec-trum in frequency domain using Fast Fourier Transfer (FFT). Then the determined harmonics and reactive components of load current are added together to form the compensating reference signals, the PI controllers then generate signals which control the Pulse Width Modulation (PWM) method. The simulation of the study is carried out under MATLAB/Simulink environment to show the usefulness of this control algorithm with nonlin-ear dynamic loads. It determines exactly the phase shift between the …

Optimized Transconductance Designs To Enhance The Linearity Performance Of Rf Front-End Receiver Circuits In 130 Nm Cmos Technology, Nandini Vitee

Student Works (2020-2029)

Highly linear front-end circuits are greatly desired for wireless receivers to improve the dynamic range. However, intermodulation distortions caused by the non-linear transconductor current limits the linearity of the front-end receiver circuit in CMOS technologies. In addition to the inherent nonlinear effect, the downscaling of CMOS further exacerbates the linearity of the circuit due to lower voltage headroom and high-field mobility. Thus, it is essential to develop effective circuit techniques that can aid linearity enhancement without jeopardizing other preferred performances such as low noise, high conversion gain, and low-power consumption. In this thesis, two different high linear transconductors are presented …

Synthesis And Application Of Ceramic Paste For High-Temperature Electronic Packaging, Ardalan Nasiri

Graduate Theses and Dissertations

This dissertation research focused on the synthesis and application of ceramic paste for high-temperature applications. An alumina paste material comprising aluminum dihydric phosphate and alumina powder was developed for high-temperature electronic packaging. Nano aluminum nitride and nano-silica powders were embedded to promote the paste curing process, limit the grain growth, and increase its bond shear strength. The chip-to-substrate bond strength was enhanced and met the MIL-STD requirements for die-attach assembly. Its encapsulation property was improved with fewer cracks compared to similar commercial ceramic encapsulants. The die-attach material and encapsulation properties tested at 500°C showed no defect or additional cracks. Thermal …

Performance Analysis Of Renewable Energy Resources In Rural Areas: A Case Study Of Solar Energy, Jackson Justo

Tanzania Journal of Engineering and Technology (TJET)

This paper presents an overview of the recent development trends of solar photovoltaic (PV) systems and the performance in the Tanzanian context. The two types of solar power generation that are considered in this paper are: i) solar PV systems and ii) concentrated solar power (CSP). The two are compared in terms of cost of energy and energy storage mechanism. Moreover, the effect of ambient temperature on the solar PV module is analyzed. In addition, a detailed analysis on using solar axis tracking to increase the power generation is also presented. The extent to which the cell surface temperature and …

High Speed, High Current Monitoring System, Nicolette Lila Ray

Electrical Engineering

Electronics testing requires lengthy data collection and analysis. Streamlining at least part of this process allows resource reallocation, and faster data processing. Verifying a signal’s efficiency is key specification for a component’s datasheet. This project focuses on streamlining data collection when measuring a device’s output current. It combines amplifier design and digital interfacing to perform monitor a device’s output current. A computer-enable interface displays a graphical output current representation. It ensures accurate, high speed, high current measurements while removing a person’s need to manually plot data after testing. A new testing method provides room for company and product growth with …

Low-Cost Test And Characterization Platform For Memristors, Lyle Jones

Boise State University Theses and Dissertations

The electrical Testing and Characterization of the devices built under research conditions on silicon wafers, diced wafers, or package parts have hampered research since the beginning of integrated circuits. The challenges of performing electrical characterization on devices are to acquire useful and accurate data, the ease of use of the test platform, the portability of the test equipment, the ability to automate quickly, to allow modifications to the platform, the ability to change the configuration of the Device Under Test (DUT) or the Memristor Based Design (MBD), and to do this within budget. The devices that this research is focused …

Resonant Metagratings For Spectral And Angular Control Of Light For Colored Rooftop Photovoltaics, Floris Uleman, Andrea Cordaro, Andrea Alù, Albert Polman

Advanced Science Research Center

We designed semitransparent metagrating supercells that enable control over the spectrum and directivity of incident light for applications in photovoltaics with tailored angular appearance. The building block of the supercells is a 100–120 nm wide and 175 nm tall silicon nanowire that shows a strong Mie resonance around λ = 650 nm. By arranging the resonant Mie scatterers into metagratings of increasing pitch (675–1300 nm), we created a Lambertian-like scattering distribution over an angular range of choice. The millimeter-sized metasurfaces were fabricated using electron beam lithography and reactive ion etching. The fabricated metasurface nearly fully suppresses specular reflection on resonance …

Rapid Prototyping Of Nanostructures With Electron Beam Induced Processing, Samaneh Esfandiarpour

Theses and Dissertations--Electrical and Computer Engineering

Focused electron beam induced processing (FEBIP) is a nano-scale fabrication technique that allows the direct deposition of functional materials. However, it suffers from significant drawbacks, such as high cost, low speed, unavailable precursors for many materials and low purity of deposits. Liquid-phase focused electron beam induced processes (LP-FEBIP) are being investigated due to the potential benefits over the gas phase technique. In this method, deposition or etching occurs at the interface between a substrate and a bulk liquid. In this work, electron beam induced deposition of copper nanostructures from aqueous solutions of copper sulfate is demonstrated. The addition of sulfuric …

Programming Of Floating-Gate Transistors For Nonvolatile Analog Memory Array, Haifa Abulaiha

Graduate Theses, Dissertations, and Problem Reports (ETD)

Since they were introduced, floating-gate (FG) transistors have been used as non-volatile digital memory. Recent research has shown that floating-gate transistors can be successfully used as analog memory, specifically as programmable voltage and current sources. However, their proliferation has been limited due to the complex programming procedure and the complex testing equipment. Analog applications such as field-programmable analog arrays (FPAAs) require hundreds to thousands of floating-gate transistors on a single chip which makes the programming process even more complicated and very challenging. Therefore, a simplified, compact, and low-power scheme to program FGs are necessary. This work presents an improved version …

Synthesis Of Graphene Using Plasma Etching And Atmospheric Pressure Annealing: Process And Sensor Development, Andrew Robert Graves

Graduate Theses, Dissertations, and Problem Reports (ETD)

Having been theorized in 1947, it was not until 2004 that graphene was first isolated. In the years since its isolation, graphene has been the subject of intense, world-wide study due to its incredibly diverse array of useful properties. Even though many billions of dollars have been spent on its development, graphene has yet to break out of the laboratory and penetrate mainstream industrial applications markets. This is because graphene faces a ‘grand challenge.’ Simply put, there is currently no method of manufacturing high-quality graphene on the industrial scale. This grand challenge looms particularly large for electronic applications where the …

The Potentials Of Faecal Sludge Treatment Using Local Conditioners In Tanzania: A Review, Doglas Benjamin1

Tanzania Journal of Engineering and Technology (TJET)

Worldwide, every day human beings generate millions of tons of Faecal Sludge (FS), which is rich in water, nutrients, energy, and organic compounds. Yet FS is not being managed in a way that permits us to derive value from its reuse, while at the same time, millions of farmers struggle with depleted soils and lack of water. In most of the developing countries, energy for cooking is mainly derived from cutting of trees, either as wood or charcoal. Resource recovery and reuse from FS can create livelihoods, enhance food security, support green economies, reduce waste and contribute to cost recovery …

Reducing The Production Cost Of Semiconductor Chips Using (Parallel And Concurrent) Testing And Real-Time Monitoring, Qutaiba Khasawneh

Electrical Engineering Theses and Dissertations

Consumer electronics changed the semiconductor industry by developing many new challenges for consumer products. One of the main challenges in the consumer product is that it propelled the volume of production to massive production, e.g. hundreds of millions of cell phones are produced yearly. Combined with the overproduction of consumer products, price pressure is another challenge for consumer products. Many of the new techniques used in the design and fabrication enabled the integration of more devices in the same chips. This reduced the cost of the chips, lowered the power consumption, increased the circuit operation speed, enabled more reliable implementation, …

High Frequency Ltcc Based Planar Transformer, Adithya Venkatanarayanan

Graduate Theses and Dissertations

As we move towards high power and higher frequency related technology, conventional wire-wound magnetics have their own limitations which has led path to the development of planar based magnetic materials. Nowadays more planar magnetic technology has been employed because it is easier to fabricate them. The planar magnetic is a transformer or an inductor that replaces the wire-wound transformer or inductors which generally uses copper wires. One of the main reasons why we move to planar magnetic technology is its operation at higher frequency which provides higher power density. This study explains in detail about the design and fabrication of …

Design And Optimization Of A High Power Density Silicon Carbide Traction Inverter, Tyler Adamson

Graduate Theses and Dissertations

This project was initiated with the goal of demonstrating a 3-phase silicon carbide based 150-kW 25 kW/L DC-AC power conversion unit capable of operation with coolant temperatures up to 90°C. The project goals were met and exceeded by first analyzing the established inverter topologies to find which one would yield the highest power density while still meeting electrical performance needs in the 150-kW range. Following topology selection, the smallest silicon carbide power module that met the electrical requirements of the system was found through experimental testing and simulation. After a power module selection was finalized, a DC link capacitor bank …

Design And Analysis Of Modular Axial Flux Switched Reluctance Motor, Rochak Shiwakoti

LSU New Orleans Theses and Dissertations

This thesis presents a new modular structure of the axial flux Switched Reluctance Motor (SRM). The design consists of four stator disks with each adjacent disk rotated 30 degrees apart and four rotor disks connected to a common shaft. The proposed design aims to reduce the unwanted radial force, mitigate the torque ripple, and improve the efficiency. The modular structure distributes the radial force and torque strokes along the axial length of the motor, potentially damping the torque pulsation. In addition, the modular structure would deliver the rating power at a lower current level, reducing the overall ohmic loss. Moreover, …

Residential Electricity Management And Protection System, Ejimonu Kosisochukwu Gabriel

Journal of International Technology and Information Management

The Residential Electricity Monitoring System is an electricity meter connected to the Internet to provide real time data on the power system in your home. The REMS is designed to replace the distribution board allowing it to conduct a series of tests on the quality of the electricity supply to your home/facility and, within your home detect basic wiring faults and allow owners and service providers to identify potential problems with the electrical systems.

The electrical monitoring system finally puts proper electrical control into the hands of the home owner by providing him with the ability to control power distribution …

Smart Charging Of Future Electric Vehicles Using Roadway Infrastructure, Sara Ahmed, Ethan Ahn, Mahmoud Reda Taha, Samer Dessouky, Moneeb Genedy, Daniel Fernandez, Ann Sebestian, Patience Raby

Publications

Inspired by the fact that there is an immense amount of renewable energy sources available on the roadways such as mechanical pressure and frictional heat, this study presented the development and implementation of an innovative charging technique for future electric vehicles (EVs) by fully utilizing the existing roadways and the state-of-the-art nanotechnology and power electronics. The project introduced a novel wireless charging system, SIC (Smart Illuminative Charging), that uses LEDs powered by piezoelectric nanomaterials as the energy transmitter source and thin film solar panels placed at the bottom of the EVs as the receiver, which is then poised to deliver …

Energy Transformation And Conservation Investigation, Mike Jackson, Holly Haney

High School Lesson Plans

Students will use a thermoelectric generator module to analyze the relationship between thermal and electrical energies. Using data collection sensors and analysis software, students will investigate the relationship between the temperature gradient across a thermoelectric generator module and the resulting electrical potential. Students will then use their data and analysis to solve problems relating to waste thermal energy in electrical systems and communicate their work to their peers and teacher.

Dc-Dc Converter For Electric Vehicle, Jason Y. Zhou, Nicholas James Mah

Electrical Engineering

In this work, a DC-DC converter is designed for an electric vehicle. The DC-DC converter is designed to provide 500W with a 200-400V input and a 12-15V adjustable output. Electric vehicle sales are beginning to increase in popularity and the need for DC-DC converters to siphon power from the tractive system is not yet fully satisfied, especially for single-seater class vehicles. Additionally, improving performance in efficiency without sacrificing wide input voltage range can benefit future DC-DC converter designs. In the end, a forward active clamp DC-DC converter is designed and tested. Additionally, spreadsheet calculators, LTSpice simulations, and Matlab scripts were …

Characterization Of High Temperature Optocoupler For Power Electronic Systems, David Gonzalez

Electrical Engineering Undergraduate Honors Theses

High-temperature devices have been rapidly increas due to the implementation of new technologies like silicon carbide, high-temperature ceramic, and others. Functionality under elevated temperatures can reduce signal integrity reducing the reliability of power electronic systems. This study presents an ongoing research effort to develop a high-temperature package for optocouplers to operate at higher temperature compared with commercial devices. Low temperature co-fired ceramic (LTCC) was used as the substrate. Bare die commercial LED and photodetectors were attached to the substrate and tested for functionality. Preliminary results show enhanced performance at elevated temperatures compared to a commercial optocoupler device.