Electrical and Electronics Commons^™

Mobile Solar Pv Trainer, Matthew Myers, Matthew Clause, Lawrence Smith

Mechanical Engineering

The aim of the Mobile Solar PV Trainer Project was to design, construct and test a versatile and robust laboratory training rig for the Cal Poly Electrical Engineering department. This project was inspired by the desire of one or more California Polytechnic State University electrical engineering professors to add laboratory components to two established upper division electrical engineering courses in photovoltaic panels and solar power. This report contains a detailed description of the trainer’s desired specifications, our ideation process, a thorough description of the selected trainer design including part drawings, assembly documentation and a bill of materials as well as …

Mems Cantilever Sensor For Thz Photoacoustic Chemical Sensing And Spectroscopy, Nathan E. Glauvitz

Theses and Dissertations

Sensitive Microelectromechanical System (MEMS) cantilever designs were modeled, fabricated, and tested to measure the photoacoustic (PA) response of gasses to terahertz (THz) radiation. Surface and bulk micromachining technologies were employed to create the extremely sensitive devices that could detect very small changes in pressure. Fabricated devices were then tested in a custom made THz PA vacuum test chamber where the cantilever deflections caused by the photoacoustic effect were measured with a laser interferometer and iris beam clipped methods. The sensitive cantilever designs achieved a normalized noise equivalent absorption coefficient of 2.83x10^-10 cm^-1 W Hz^-1/2 using a 25 …

Design, Fabrication, And Testing Of An Emr Based Orbital Debris Impact Testing Platform, Jeffrey J. Maniglia Jr.

Master's Theses

This paper describes the changes made from Cal Poly’s initial railgun system, the Mk. 1 railgun, to the Mk. 1.1 system, as well as the design, fabrication, and testing of a newer and larger Mk. 2 railgun system. The Mk. 1.1 system is developed as a more efficient alteration of the original Mk. 1 system, but is found to be defective due to hardware deficiencies and failure, as well as unforeseen efficiency losses. A Mk. 2 system is developed and built around donated hardware from the Naval Postgraduate School. The Mk. 2 system strove to implement an efficient, augmented, electromagnetic …

Cal Poly Brocade Challenge 2013, Chandler Morehardt, Alexa Coburn, Juan Silva, Kerry Sun, Greg Wang, Raul Chagoya, Jd Torres

Architectural Engineering

No abstract provided.

Digitally Programmable Rf Mems Filters With Mechanically Coupled Resonators, Hengky Chandrahalim, Sunil Ashok Bhave

AFIT Patents

A digitally-tunable RF MEMS filter includes a substrate and a plurality of mechanically coupled resonators, wherein a first and a last resonator of the plurality of mechanically coupled resonators are configured to be electrostatically transduced. One or more of the plurality of mechanically coupled resonators are configured to be biased relative to the substrate such that the one or more biased resonators may be brought substantially in contact with the substrate. In a method of digitally tuning an RF MEMS filter having a mechanically coupled resonator array, a DC bias voltage is applied to at least a first resonator and …

Computational Design Of The Electrical And Mechanical Performance Of Steerable Mems Antennas, Morgan Andrew Roddy

Graduate Theses and Dissertations

This thesis describes the origins, improvements, and variations of a broadband microwave antenna that can be beam-steered by a micro-electromechanical system (MEMS). The steerable MEMS antenna of this work was comprised of a planar antenna on top of a Silicon membrane. The membrane is etched to create a gimbal hinge structure and a platform which supported the antenna and gave it one or two degrees of freedom of rotation. The antennas presented were broadband and fed by a coplanar waveguide (CPW) transmission line which traversed the hinge structure. The antenna's orientation in space was designed to be changed through electrostatic …

Technology Portal For Energy Efficient Buildings, Larry D. Hermanson, Daniel Studer, Annie Mroz

STAR Program Research Presentations

Project: Technology Portal for Energy Efficient Buildings

Date: August 2, 2012

Author: Larry Hermanson

Mentor: Daniel Studer

Cohort: Annie Mroz

Lab site: National Renewable Energy Laboratory (NREL)

Buildings account for 71% of the electricity demand and 39% of the primary energy consumption in the United States. The Commercial Buildings Group at NREL provides builders, designers and building owners accurate information to significantly improve the energy efficiency of new and existing buildings. The Technology Portal for Energy Efficient Buildings will increase the accessibility of standardized and credible energy performance data for all building systems, thereby allowing building owners to better evaluate …

Fabrication And Characterization Of Torsional Micro-Hinge Structures, Mike Madrid Marrujo

Master's Theses

ABSTRACT

Fabrication and Characterization of Torsional Micro-Hinge Structures

Mike Marrujo

There are many electronic devices that operate on the micrometer-scale such as Digital Micro-Mirror Devices (DMD). Micro actuators are a common type of DMD that employ a diaphragm supported by torsional hinges, which deform during actuation and are critical for the devices to have high stability and reliability. The stress developed within the hinge during actuation controls how the actuator will respond to the actuating force. Electrostatically driven micro actuators observe to have a fully recoverable non-linear viscoelastic response. The device consists of a micro-hinge which is suspended by two …

Design, Construction, And Evaluation Of An Automated Chicken Coop Door, Kyle Inks

BioResource and Agricultural Engineering

This senior project takes a look into the design, construction, and evaluation of an automated chicken coop door. The idea and need for such a door came from my mother Jan Inks. The parameters for the project include, low production cost, easy installation on existing coops, sleek design, automatically open at a set time in the morning, and automatically close at a set time in the evening.

Experimental And Numerical Investigations Of Tubular-Shaped Direct Methanol Fuel Cells (Dmfcs), Travis R. Ward

Master's Theses

This study focuses on both the numerical and experimental investigations of the novel, passively operated, tubular-shaped, Direct Methanol Fuel Cell (DMFC) as an alternative geometry to the traditional planar-shaped fuel cell. The benefit of the tubular geometry compared to the planar geometry is the higher instantaneous volumetric power density provided by the larger active area, which could be beneficial in applications that require a high instantaneous power while occupying a small volume. First, a two-dimensional, two-phase, non-isothermal model was developed to investigate the steady-state performance and design characteristics of a tubular-shaped, passive DMFC. It was found that a higher ambient …

Development Of A Cubesat Instrument For Microgravity Particle Damper Performance Analysis, John Trevor Abel

Master's Theses

Spacecraft pointing accuracy and structural longevity requirements often necessitate auxiliary vibration dissipation mechanisms.  However, temperature sensitivity and material degradation limit the effectiveness of traditional damping techniques in space.  Robust particle damping technology offers a potential solution, driving the need for microgravity characterization.   A 1U cubesat satellite presents a low cost, low risk platform for the acquisition of data needed for this evaluation, but severely restricts available mass, volume, power and bandwidth resources.  This paper details the development of an instrument subject to these constraints that is capable of capturing high resolution frequency response measurements of highly nonlinear particle damper dynamics.

Shaped Mems Contact, Ronald A. Coutu Jr., Paul E. Kladitis, Robert L. Crane

AFIT Patents

A MEMS switch fabrication process and apparatus inclusive of a bulbous rounded surface movable contact assembly that is integral with the switch movable element and achieving of long contact wear life with low contact electrical resistance. The disclosed process is compatible with semiconductor integrated circuit fabrication materials and procedures and includes an unusual photoresist reflow step in which the bulbous contact shape is quickly defined in three dimensions from more easily achieved integrated circuit mask and etching-defined precursor shapes. A plurality of differing photoresist materials are used in the process. A large part of the contact and contact spring formation …

A Review Of Variable Valve Timing Devices, Paul Shelton

Mechanical Engineering Undergraduate Honors Theses

Variable valve timing (VVT) has evolved from simple, manual controlled engine management to automatic, electronic works of engineering. Starting from the need for more power and extending into fuel efficiency and low emissions, VVT has evolved from the constant changing of needs. This paper summarizes various devices used to control the timing of valves from the early 1920s up until 2007.

Electrically Steerable Diffraction Gratings For Hyperspectral Imaging: A Microelectromechanical System Design And Fabrication, Saban Atinc Delican

Theses and Dissertations

The current research is focused on the design and fabrication of an electrically programmable diffraction grating using standard micro electro mechanical systems (MEMS) technology. The goal is to design a beam steering element required to build very small hyperspectral imaging (HSI) sensors. The diffraction grating will be used to perform beam-dispersion - a critical step in the imaging process. The proposed transmissive diffraction grating based approach will minimize the overall size and the number of components in the physical design of the hyperspectral imagers, thereby enabling us to exploit the traditional advantages of MEMS such as increased reliability, smaller size, …

Performance Comparison Of Pb(Zr0.52Ti0.48)O3-Only And Pb(Zr0.52Ti0.48)O3-On-Silicon Resonators, Hengky Chandrahalim, Sunil A. Bhave, Ronald G. Polcawich, Jeff Pulskamp, Dan Judy, Roger Kaul, Madan Dubey

Faculty Publications

This paper provides a quantitative comparison and explores the design space of lead zirconium titanate (PZT)–only and PZT-on-silicon length-extensional mode resonators for incorporation into radio frequency microelectromechanical system filters and oscillators. We experimentally measured the correlation of motional impedance (R_X) and quality factor (Q) with the resonators’ silicon layer thickness (t_Si). For identical lateral dimensions and PZT-layer thicknesses (t_PZT), the PZT-on-silicon resonator has higher resonant frequency (f_C), higher Q (5100 versus 140), lower R_X (51 Ω versus 205 Ω), and better linearity [third-order input intercept …

Characterizationn Of Polumer-Based Mems Pyroelectic Infrared Detector, Mark E. Allard

Theses and Dissertations

AFRL/MLPJE had developed a novel thermal sensing material termed protein-impregnated-polymer (PIP). Thus far, a proof-of-concept has been demonstrated using a macro-sized pixel (0.64 mm²) as a bolometric detector. In an effort to better characterize this novel thermal sensing material, experimental data was used to determine figures of merit (FOMs) comparative to off-the-shelf thermal detectors. Microelectromechanical (MEMS) pixels were designed and used as the support structure for an inkjet-deposited droplet of the PIP. During the material characterization, two observations were made: PIP is a pyroelectric material, and the polymer (polyvinyl alcohol (PVA)) without the protein was found to be …

Socio-Economic Impacts Of Computer Viruses In Tanzania, M Victor

Tanzania Journal of Engineering and Technology (TJET)

This paper reports on a research project conducted with an objective of identifying and assessing various approaches used by different computer users (Management, System Administrators and end users) in Tanzania to combat computer viruses (CVs), and to assess users' awareness level on CVs. Specifically, the study aimed at assessing the awareness level on CVs to the Tanzanian business community; analyze the socio -economic impact caused by CVs in Tanzania and; assess existing methods, capacity and limitations on controlling CVs in Tanzania. Data was collected using both questionnaires and interview from financial institutions such as NBC and BOT, and telecommunications sector …

Insulator Charging In Rf Mems Capacitive Switches, Jay F. Kucko

Theses and Dissertations

While capacitive radio frequency microelectromechanical (RF MEM) switches are poised to provide a low cost, high isolation, low power alternative to current RF switch technologies, there are still reliability issues limiting switch lifetime. Previous research identified insulator charging as a primary cause of switch failure. Changes in switch pull-in and release voltages were measured to provide insight into the mechanisms responsible for charging and switch failure. A spatial and temporal dependent model was developed to describe silicon nitride's time-dependent charging as a function of applied bias. This model was verified by applying constant biases to metal-silicon nitride-silicon capacitors and tracking …

Head Tracking For 3d Audio Using A Gps-Aided Mems Imu, Jacque M. Joffrion

Theses and Dissertations

Audio systems have been developed which use stereo headphones to project sound in three dimensions. When using these 3D audio systems, audio cues sound like they are originating from a particular direction. There is a desire to apply 3D audio to general aviation applications, such as projecting control tower transmissions in the direction of the tower or providing an audio orientation cue for VFR pilots who find themselves in emergency zero-visibility conditions. 3D audio systems, however, require real-time knowledge of the pilot's head orientation in order to be effective. This research describes the development and testing of a low-cost head …

Electrostatic Radio Frequency (Rf) Microelectromechanical Systems (Mems) Switches With Metal Alloy Electric Contacts, Ronald A. Coutu Jr.

Theses and Dissertations

RF MEMS switches are paramount in importance for improving current and enabling future USAF RF systems. Electrostatic micro-switches are ideal for RF applications because of their superior performance and low power consumption. The primary failure mechanisms for micro-switches with gold contacts are becoming stuck closed and increased contact resistance with increasing switch cycles. This dissertation reports on the design, fabrication, and testing of micro-switches with sputtered bi-metallic (i.e., gold (Au)-on-Au-(6.3at%)platinum (Pt)), binary alloy (i.e., Au-(3.7at%)palladium (Pd) and Au-(6.3at%)Pt), and ternary alloy (i.e., Au-(5at%)Pt-(0.5at%)copper (Cu)) contact metals. Performance was evaluated, in-part, using measured contact resistance and lifetime results. The micro-switches with …

A Tightly-Coupled Ins/Gps Integration Using A Mems Imu, Jonathan M. Neu

Theses and Dissertations

Micro-Electro-Mechanical Systems (MEMS) technology holds great promise for future navigation systems because of the reduced size and cost of MEMS inertial sensors relative to conventional devices. Current MEMS devices are much less accurate than standard inertial sensors, but they can still be useful. In this thesis, data was recorded from an inexpensive MEMS inertial measurement unit and integrated with GPS measurements using a tightly-coupled Kalman filter. The overall goal of this research is to investigate the usefulness of MEMS sensors for a small, real-time, low-cost INS/GPS integration. A golf cart was used to collect dynamic data, along with a commercial …

Review Of The Product Development Process And Information Flow In The Manufacturing Industry: Problems And A Possible Wav Forward, E Opiyo

Tanzania Journal of Engineering and Technology (TJET)

No abstract provided.

Demonstrating Optothermal Actuators For An Autonomous Mems Microrobot, Francis R. Szabo

Theses and Dissertations

There are numerous applications for microrobots which are beneficial to the Air Force. However, the microrobotics field is still in its infancy, and will require extensive basic research before these applications can be fielded. The biggest hurdle to be solved, in order to create autonomous microrobots, is generating power for their actuator engines. Most present actuators require orders of magnitude more power than is presently available from micropower sources. To enable smaller microrobots, this research proposed a simplified power concept that eliminates the need for on-board power supplies and control circuitry by using actuators powered wirelessly from the environment. This …

Thin Film Encapsulation Of Radio Frequency (Rf) Microelectromechanical Systems (Mems) Switches, Eric D. Marsh

Theses and Dissertations

Microelectromechanical systems (MEMS) radio frequency (RF) switches have been shown to have excellent electrical performance over a wide range of frequencies. However, cost-effective packaging techniques for MEMS switches do not currently exist. This thesis involves the design of RF-optimized encapsulations consisting of dielectric and metal layers, and the creation of a novel thin film encapsulation process to fabricate the encapsulations. The RF performance of several encapsulation designs are evaluated with an analytical model, full wave electromagnetic simulation, and laboratory testing. Performance degradation due to parasitic and reflection losses due to the package is considered, and RF feed-throughs of the transmission …

Application Of Vibrational Techniques In Determination Of Dynamic Properties Of Agricultural Products-State Of The Arton Of Vibrational Techniques In Determination Of Dynamic Properties Of Agricultural Products-State Of The Art, Silas Kajuna

Tanzania Journal of Engineering and Technology (TJET)

Vibration is one of the techniques employed in the determination of dynamic properties of fruits and vegetables. It entails generation of a mechanical or acoustic vibrational signal which is propagated through the flesh of the agricultural material. A transducer is either attached or held close to the specimen to monitor the propagation of the signal through the specimen. The manner in which the signal is transmitted through the material is analyzed, and the dynamic properties of the specimen which relate to its firmness or its internal being are derived. The technique has been around for the past 30 years or …

Micro Hydro Power, Frederick J. Munster

Maine Collection

Micro Hydro Power

by Frederick J. Munster

Department of Economic and Community Development, August, Me. 1999 (?).

Contents: Introduction / History of Hydropower in Maine / Renewables / Why Micro Hydro / Determining Flow / Determining Head / Estimating Energy Potential / Hydro Turbines / Dams, Impoundments, Penstocks and Power Houses / Utility Interconnected Systems / Battery Charging Systems / Operation and Maintenance / Economics / Regulation of Hydro Development / For More Information / References

Fuel Cells, Frederick J. Munster Jr.

Maine Collection

Fuel Cells

by Frederick J. Munster Jr.

Edited by: Mr. Christopher Carroll

Maine Department of Economic Development, Augusta, Maine, 1998.

Contents: Hydrogen / Hydrogen Safety / Electrolysis / Electrolyzers / History of Fuel Cells / How Fuel Cells Operate / Fuel Cell Types / Fuel Cell Electrochemistry / Power Systems / Fuel Cells in Transportation / Hydrogen Powered Internal Combustion Engines / Home, Garden, Education and Industry / For More Information / Glossary / References

Micro-Electromechanical Switches For Micro-Satellite Power Transfer, Glen A. Kading

Theses and Dissertations

In the past few years, microelectromechanical systems (MEMS) have emerged as a promising new technology with tremendous application potential. One of the possible implementations of MEMS technology is in the development of micro-satellites. It should be possible to mass-produce micro-satellites at a fraction of the cost of one conventional satellite. In order for satellites to be robust, a method of transferring power to systems must be addressed. As micro-satellites are made with conventional integrated circuit technologies at a very small scale, a means of transferring power on a similar scale will be investigated. This research addresses the issue of the …

Microelectromechanical Scanner Using A Vertical Cavity Surface Emitting Laser, Joseph G. Bouchard Jr.

Theses and Dissertations

Optical scanners play a prominent role in the commercial and military industries. The scanner's size, cost and reliability are critical characteristics. In this research a microoptical scanning system was fabricated by incorporating a vertical cavity surface emitting laser (VCSEL) onto a surface machined microelectromechanical die. The micro optics for laser beam steering includes a 135 deg mirror, a Fresnel lens, a lateral scanning rotating mirror, and a vertical scanning fan mirror. The VCSEL was attached to the die by solder and electrical connection was provided by wire bonding. Based on far field measurements the scanner had a lateral scan angle …

Design And Development Of Microswitches For Micro-Electro-Mechanical Relay Matrices, Mark W. Phipps

Theses and Dissertations

Many different micro-electro-mechanical switches were designed in the Multi-User MEMS processes (MUMPs) and deep x-ray lithography and electroforming (LIGA) processes. The switches were composed of actuators that operated based upon either electrostatic forces or thermal forces. A thermally activated beam flexure actuator that operated based upon differential heating was used extensively. This actuator, which was fabricated in the MUMPs process, was able to deflect up to 12 microns with a total input power of less than 25 mW. The thermal resistance, which was needed to model this actuator, was determined from a material constant, 1.9 ± 0.08 m^1.5-°C-W …