Electrical and Electronics Commons^™

Challenges In Flexible Microsystem Manufacturing : Fabrication, Robotic Assembly, Control, And Packaging., Danming Wei

Electronic Theses and Dissertations

Microsystems have been investigated with renewed interest for the last three decades because of the emerging development of microelectromechanical system (MEMS) technology and the advancement of nanotechnology. The applications of microrobots and distributed sensors have the potential to revolutionize micro and nano manufacturing and have other important health applications for drug delivery and minimal invasive surgery. A class of microrobots studied in this thesis, such as the Solid Articulated Four Axis Microrobot (sAFAM) are driven by MEMS actuators, transmissions, and end-effectors realized by 3-Dimensional MEMS assembly. Another class of microrobots studied here, like those competing in the annual IEEE Mobile …

Grid-Connected Photovoltaic Systems Based On Nonlinear Control., Pablo R. Rivera

Electronic Theses and Dissertations

Nowadays, due to the high-scale penetration of photovoltaic systems, reliable and efficient grid-connected photovoltaic (PV) systems utilizing the advances of power electronics and control system technology are desirable. Thus, single-stage grid-connected photovoltaic systems, have gained attention, especially in low voltage applications. However, PV systems exhibit nonlinear behavior that could negatively affect the performance of the system if they are not adequately compensated for. In this dissertation, using the general structure for the synchronous dq0 frame, a single-stage three-phase grid-connected photovoltaic system, and a single-stage single-phase grid-connected PV system, both with a nonlinear control strategy, are developed to track the maximum …

Application Of Modular Multilevel Converters (Mmc) Using Phase-Shifted Pwm And Selective Harmonic Elimination In Distribution Systems, Thouhidul Islam

Graduate Theses and Dissertations

Reducing the size and weight of a power electric system is a prodigious challenge to researchers as the development of the latest technologies emerge in the field of electrical engineering. A similar urge is there to develop a light-weight mobile power substation (MPS) to use in the electric power distribution systems during emergency conditions. This thesis proposes a power electronics based solution using the modular multilevel converter (MMC) topology to design the MPS system. The market-available power semiconductor devices are analyzed and suitable devices are selected to design the system. The phase-shifted pulse width modulation (PS-PWM) and selective harmonic elimination …

From A Locally Competitive Algorithm To Sensory Relevance Models, Walter Woods

Electrical and Computer Engineering PhD Day

This poster addresses the development of a new Machine Learning (ML) mechanism, the Sensory Relevance Model (SRM), as a means of splitting information processing tasks into two sub-tasks with more intuitive properties. Specifically, SRMs are a front-end for other ML techniques, re-mapping the input data to a similar space with significantly more sparsity, achieved through the transformation and suppression of inputs irrelevant to the task. Prior work has attempted to reveal this information for Neural Networks (NNs) either as a post-processing step via saliency maps or through a simple masking of the input achieved with a dot product (so-called ``attention'' …

Coaxial Magnetic Gearbox With A Flux Concentration Halbach Rotor And Consequent Pole Rotor Typology, Ho Yin Wong

Electrical and Computer Engineering PhD Day

This paper presents the performance comparison between a flux concentration and triple permanent magnet consequent pole magnetic gear rotor typology with the same 7.5:1 gear ratio. The triple permanent magnet consequent pole magnetic gear is unique in that it can create torque change through two field heterodyning pole combinations. The performance with respect to volumetric and mass torque density is considered. It is shown that the flux concentration typology can operate with a higher mass and volumetric higher torque density, even when using a low flux concentration ratio rotor.

Drafting In Self-Timed Circuits, Christopher Cowan

Electrical and Computer Engineering PhD Day

Intervals between data items propagating in self-timed circuits are controlled by handshake signals rather than by a clock. The sequence of handshakes can be abstracted as the movement of “tokens”. In many self-timed designs, a trailing token will catch up with a leading token, even when it trails by thousands of gate delays. Simulations in SPICE of a simple GasP circular FIFO reveal this effect. Contrary to earlier work, we find the cause of drafting to be charge stored on an isolated node between two series transistors. This mechanism occurs in many decision gates that implement a logical AND. The …

Some Aggregation Operators For Bipolar-Valued Hesitant Fuzzy Information, Florentin Smarandache, Tahir Mahmood, Kifayat Ullah, Qaisar Khan

Branch Mathematics and Statistics Faculty and Staff Publications

In this article we define some aggregation operators for bipolar-valued hesitant fuzzy sets. These operations include bipolar-valued hesitant fuzzy ordered weighted averaging (BPVHFOWA) operator, bipolar-valued hesitant fuzzy ordered weighted geometric (BPVHFOWG) operator and their generalized forms. We also define hybrid aggregation operators and their generalized forms and solved a decision-making problem on these operation.

Assessing The Spatial Accuracy And Precision Of Lidar For Remote Sensing In Agriculture, Surya Saket Dasika

Theses and Dissertations--Biosystems and Agricultural Engineering

The objective of this whole study was to evaluate a LiDAR sensor for high-resolution remote sensing in agriculture. A linear motion system was developed to precisely control the dynamics of LiDAR sensor in effort to remove uncertainty in the LiDAR position/velocity while under motion. A user control interface was developed to operate the system under different velocity profiles and log LiDAR data synchronous to the motion of the system. The LiDAR was then validated using multiple test targets with five different velocity profiles to determine the effect of sensor velocity and height above a target on measurement error. The results …

Contributions To Hybrid Power Systems Incorporating Renewables For Desalination Systems, Nasser Alawhali

Theses and Dissertations--Electrical and Computer Engineering

Renewable energy is one of the most reliable resource that can be used to generate the electricity. It is expected to be the most highly used resource for electricity generation in many countries in the world in the next few decades. Renewable energy resources can be used in several purposes. It can be used for electricity generation, water desalination and mining. Using renewable resources to desalinate the water has several advantages such as reduce the emission, save money and improve the public health. The research described in the thesis focuses on the analysis of using the renewable resources such as …

Ball Oscillating Bouncer, Eric Blok, Daniel Altemese, Ryan Nowacki, Maram Qurban

Williams Honors College, Honors Research Projects

The purpose of this report is to document the need, objectives, marketing and engineering requirements, as well as validate the design of an autonomous control device capable of continuously bouncing a table tennis ball on a paddle. This includes the design of a self correcting system using lightweight materials, and as few sensors and components as possible to achieve a compact, portable design. To accomplish this, the system is designed to react to a ball falling from as short a distance as 10 centimeters above the paddle, meaning all sensor processing, control processing, and motor drives should be able to …

Stability Analysis And Design Of A Tracking Filter For Variable Frequency Applications, Pranav Aramane

Theses and Dissertations--Electrical and Computer Engineering

The work presented in this thesis is a frequency adaptive tracking filter that can be used in exact tracking of power frequencies and rejection of unwanted harmonics introduced during power disturbances. The power synchronization process includes power converters and other equipment that have many non-linear components that introduce unwanted harmonics. This new design is motivated by the requirement of a filter that can filter all the harmonics and exactly track a rapidly varying fundamental frequency with little time delay and phase error. This thesis analyzes the proposed filter mathematically based on Lyapunov theory and simulations are presented to show the …

Cyber-Based Contingency Analysis And Insurance Implications Of Power Grid, Zhiyuan Yang

Dissertations, Master's Theses and Master's Reports

Cybersecurity for power communication infrastructure is a serious subject that has been discussed for a decade since the first North American Electric Reliability Corporation (NERC) critical infrastructure protection (CIP) initiative in 2006. Its credibility on plausibility has been evidenced by attack events in the recent past. Although this is a "very high impact, rare probability" event, the establishment of quantitative measures would help asset owners in making a series of investment decisions. First, this dissertation tackles attackers' strategies based on the current communication architecture between remote IP-based (unmanned) power substations and energy control centers. Hypothetically, the identification of intrusion paths …

Energy Storage Control And Requirements For Inverter-Based Microgrids, Mehrzad Mohammadi Bijaieh

Dissertations, Master's Theses and Master's Reports

The intermittent nature of distributed renewable sources such as wind or solar requires integration of energy storage systems. In this dissertation a distributed form of the Hamiltonian Surface Shaping and Power Flow Control (HSSPFC) method is used to determine the energy storage requirements of three-phase inverter-based microgrids. The overall control is appropriate to be integrated into a hierarchical control system. As the primary control, a novel dq droop control sets the local references and is supported by a level-zero Hamiltonian controller which includes energy storage feed-forward and feedback, and an inverter feed-forward controls. Here, the energy storage element performs as …

Flexible Custom Electric Skateboard, Caleb Adam Kelsay

Electrical Engineering

At Cal Poly traveling long distances only accessible by foot such as across campus or from the car park to class can be tiring and time-consuming. While not physically demanding, the trek consumes time in our tight college life schedule. To improve our time efficiency this project provides a relatively lightweight, powered solution to quickly and effectively travel long distances while maintaining full control and safety even on hills, a current limitation of traditional skateboards.

This electric skateboard includes the battery capacity to travel all around campus on a single charge with a compact and flexible skateboard design that provides …

Quantitative Analysis Of Regenerative Energy In Electric Rail Traction Systems, Mahmoud Saleh, Oindrilla Dutta, Yusef Esa, Ahmed Mohamed

Publications and Research

This paper aims at determining the influential factors affecting regenerative braking energy in DC rail transit systems. This has been achieved by quantitatively evaluating the dependence of regenerative energy on various parameters, such as vehicle dynamics, train scheduling, ground inclination and efficiency of the electrical devices. The recuperated power and energy have been presented by a mathematical model, comprising of a set of empirical forms, which allows for thorough analysis. A detailed simulation model of a typical DC-traction system has been developed to validate the developed empirical forms. The results verified the validity of the proposed mathematical model, and demonstrated …

Optimal Microgrids Placement In Electric Distribution Systems Using Complex Network Framework, Mahmoud Saleh, Yusef Esa, Nwabueze Onuorah, Ahmed Mohamed

Publications and Research

This paper provides a new approach to find the optimal location for Microgrids (MGs) in electric distribution systems using complex network analysis. An optimal location in this paper refers to a location that would result in increased grid resilience, reduced power losses, less line loading, higher voltage stability and secured supply to critical loads during power outage. The criteria used to find the optimal placement of MGs were based on the centrality analysis adopted from complex network theory, the center of mass concept used in physics, and the controlled delivery grid (CDG) concept. An IEEE 30-bus system was used as …

Event And Time-Triggered Control Module Layers For Individual Robot Control Architectures Of Unmanned Agricultural Ground Vehicles, Tyler Troyer

Department of Agricultural and Biological Systems Engineering: Dissertations, Theses, and Student Research

Automation in the agriculture sector has increased to an extent where the accompanying methods for unmanned field management are becoming more economically viable. This manifests in the industry’s recent presentation of conceptual cab-less machines that perform all field operations under the high-level task control of a single remote operator. A dramatic change in the overall workflow for field tasks that historically assumed the presence of a human in the immediate vicinity of the work is predicted. This shift in the entire approach to farm machinery work provides producers increased control and productivity over high-level tasks and less distraction from operating …

Energy Management Algorithm For Resilient Controlled Delivery Grids, Mahmoud Saleh, Yusef Esa, Ahmed Mohamed, Haim Grebel, Roberto Rojas-Cessa

Publications and Research

Resilience of the power grid is most challenged at power blackouts since the issues that led to it may not be fully resolved by the time the power is back. In this paper, a Real-Time Energy Management Algorithm (RTEMA) has been developed to increase the resilience of power systems based on the controlled delivery grid (CDG) concept. In a CDG, loads communicate with a central controller, periodically sending requests for power. The central controller runs an algorithm, based on which it may decide whether to grant the requested energy fully or partially. Therefore, the CDG limits loads discretionary access to …

Design Of Dc-Link Vscf Ac Electrical Power System For The Embraer 190/195 Aircraft, Eduardo Francis Carvalho Freitas, Nihad E. Daidzic

Journal of Aviation Technology and Engineering

A proposed novel DC-Link VSCF AC-DC-AC electrical power system converter for Embraer 190/195 transport category airplane is presented. The proposed converter could replace the existing conventional system based on the CSCF IDGs. Several contemporary production airplanes already have VSCF as a major or backup source of electrical power. Problems existed with the older VSCF systems in the past; however, the switched power electronics and digital controllers have matured and can be now, in our opinion, safely integrated and replace existing constant-speed hydraulic transmissions powering CSCF AC generators. IGBT power transistors for medium-level power conversion and relatively fast efficient switching are …

Autonomous Speed Control For Kia Optima, Andrew J. Combs, Kyle Fugatt, Kevin Mcfall

The Kennesaw Journal of Undergraduate Research

The standard method for speed control is the cruise control system built into most modern vehicles. These systems employ a PID controller which actuates the accelerator thus, in turn, maintains the desired vehicle speed. The main drawback of such a system is that typically the cruise control will only engage above 25 mph. The goal of this paper is to describe a system which we used to control vehicle speed from a stop to any desired speed using an Arduino microcontroller and a CAN BUS shield, from where autonomous features can be built upon. With this system, we were able …

Dc House Energy Management System, Zachary L. Eldredge, Zoe M. Hay

Electrical Engineering

In this work, a previously completed proof of concept for an Energy Management System (EMS) for the DC House project has been revised and re-implemented. The implemented design changes will improve the performance and reproducibility of the system. This new design of the EMS replaces the two-separate buck and boost DC-DC converters with a single bidirectional DC-DC converter to reduce components and improve efficiency. Analysis of the bidirectional DC-DC converter shows high efficiency especially at larger load currents. The code of the previous work was updated for smoother operation as well as to accommodate an LCD capable of displaying more …

Dc-Dc Converter Control System For The Energy Harvesting From Exercise Machines System, Alexander Sireci

Master's Theses

Current exercise machines create resistance to motion and dissipate energy as heat. Some companies create ways to harness this energy, but not cost-effectively. The Energy Harvesting from Exercise Machines (EHFEM) project reduces the cost of harnessing the renewable energy. The system architecture includes the elliptical exercise machines outputting power to DC-DC converters, which then connects to the microinverters. All microinverter outputs tie together and then connect to the grid. The control system, placed around the DC-DC converters, quickly detects changes in current, and limits the current to prevent the DC-DC converters and microinverters from entering failure states.

An artificial neural …

Light Sensing Automated Blinds, Andrew B. Hodges, Ryan C. Flick

Electrical Engineering

This project is solving the problem of wasted energy within buildings and homes, because currently the lights turned on inside building do not utilize natural, ambient light from the sun. Rather than having unnecessary light from a light source, the automated light sensing smart blinds can sense the amount of light outside the window and in the room, and then adjust the angle of the blinds to save energy by utilizing the available outdoor light. This way, the light source will not be running at maximum power output while there is excess light coming through the window. This project aims …

An Exact Analysis For Four-Order Acousto-Optic Bragg Diffraction Which Incorporates Both Incident Light Angle And Sound Frequency Dependencies, Adeyinka Sunday Ademola

Electrical Engineering Theses

This thesis extends the prior work which produced an exact solution to the four-order acousto-optic (AO) Bragg cell with assumed fixed center frequency and with exact Bragg angle incident light. The extension predicts the model that incorporates the dependencies of both the input angle of light and the sound frequency. Specifically, a generalized 4^th order linear differential equation (DE), is developed from a simultaneous analysis of four coupled AO system of DEs. Through standard methods, the characteristic roots, which requires solving a quartic equation, is produced. Subsequently, a derived system of homogeneous solutions, which absorbs the roots obtained using …

Automation In Entertainment: Concept, Design, And Application, Ryan Thally

Undergraduate Honors Theses

The focus of this thesis is to explore the automation technology used in the modern entertainment industry. Upon completion of my thesis, I will deliver a working prototype of the chosen technology and present its capabilities in a choreographed show.

Centralized Control For Dc Microgrid Using Finite State Machine, Mahmoud Saleh, Yusef Esa, Ahmed Mohamed

Publications and Research

In this paper, an autonomous communication-based centralized control for DC microgrids (MG) has been developed and implemented. The proposed controller enables smooth transition between various operating modes. Finite state machine (FSM) has been used to mathematically describe the various operating modes (states), and events that may lead to mode changes (transitions). Therefore, the developed centralized controller aims at optimizing the performance of MG during all possible operational scenarios, while maintaining its reliability and stability. Results of selected cases have been presented. These results show stable transition between modes, verifying the validity and applicability of the proposed controller.

Omni-Directional Infrared 3d Reconstruction And Tracking Of Human Targets, Emrah Benli

Theses and Dissertations

Omni-directional (O-D) infrared (IR) vision is an effective capability for mobile systems in robotics, due to its advantages: illumination invariance, wide field-of-view, ease of identifying heat-emitting objects, and long term tracking without interruption. Unfortunately, O-D IR sensors have low resolution, low frame rates, high cost, sensor noise, and an increase in tracking time. In order to overcome these disadvantages, we propose an autonomous system application in indoor scenarios including 1) Dynamic 3D Reconstruction (D3DR) of the target view in real time images, 2) Human Behavior-based Target Tracking from O-D thermal images, 3) Thermal Multisensor Fusion (TMF), and 4) Visual Perception …

Heterogeneous Multi-Sensor Fusion For 2d And 3d Pose Estimation, Hanieh Deilamsalehy

Dissertations, Master's Theses and Master's Reports

Sensor fusion is a process in which data from different sensors is combined to acquire an output that cannot be obtained from individual sensors. This dissertation first considers a 2D image level real world problem from rail industry and proposes a novel solution using sensor fusion, then proceeds further to the more complicated 3D problem of multi sensor fusion for UAV pose estimation.

One of the most important safety-related tasks in the rail industry is an early detection of defective rolling stock components. Railway wheels and wheel bearings are two components prone to damage due to their interactions with the …

Minimum Time Control Of Paralleled Boost Converters, Shishir Patel

Dissertations, Master's Theses and Master's Reports

Demand for electrification is booming in both, traditional and upcoming generations of technological advancements. One of the constituent blocks of these electrified systems is Power conversion. Power conversion systems are often constructed by paralleling multiple power converter blocks for high performance and reliability of overall system. An advanced control technique is developed with an aim to optimize system states of heterogeneous power converters within minimum time while maintaining feasible stress level on individual power converter blocks. Practical implementation of real-time controller and performance improvement strategies are addressed. Experimental results validating high performance control scheme, and sensitivity analysis of system states …

Underwater Robot, Joseph E. Beck, Matthew Crislip, Cody Bobek, Peyton Lucas

Williams Honors College, Honors Research Projects

Remotely Operated Vehicles (ROVs) are remote controlled drones operated by a non-local user. The ROV we plan to build is connected by a tethering wire to a floating buoy that contains an antenna which will send signals between the base station and the ROV. The ROV is equipped with a video camera, ballast system, propulsion system, lights, and a depth sensor. The ROV will transmit a live video feed to the user, while receiving input signals to control its movement from the base station.