Controls and Control Theory Commons^™

Quadrotor Swarm Arena (Quasar) Development Of A Swarm Control Testbed, Shane T. Stebler, William Mackunis

Beyond: Undergraduate Research Journal

Swarm control systems are increasingly popular in the robotics industry and academia due to their many potential applications. The goal of the Quadrotor Swarm Arena (QuaSAr) project is to construct a quadrotor swarm control testbed to provide researchers with the tools needed to experimentally investigate this emerging science. This testbed is equipped with a motion capture system, test control station, and numerous quadrotor UAVs. MATLAB-Simulink is utilized for control law development, data processing, and test control. This configuration allows researchers to test developing control law in a 'plug and play' manner as control development and test control are all completed …

Estimation Of 3d Orientation From Inertial Sensors With Different/Nonuniform Sampling, Soulaimane Berkane

Western Research Forum

No abstract provided.

Some Insights Into The Migration Of Double Imaginary Roots Under Small Deviation Of Two Parameters, Dina Alina Irofti, Keqin Gu, Islam Boussaada, Silviu-Iulian Niculescu

SIUE Faculty Research, Scholarship, and Creative Activity

This paper studies the migration of double imaginary roots of the systems’ characteristic equation when two parameters are subjected to small deviations. The proposed approach covers a wide range of models. Under the least degeneracy assumptions, we found that the local stability crossing curve has a cusp at the point that corresponds to the double root, and it divides the neighborhood of this point into an S-sector and a G-sector. When the parameters move into the G-sector, one of the roots moves to the right halfplane, and the other moves to the left half-plane. When the parameters move into the …

Strong Stability Of A Class Of Difference Equations Of Continuous Time And Structured Singular Value Problem, Qian Ma, Keqin Gu, Narges Choubedar

SIUE Faculty Research, Scholarship, and Creative Activity

This article studies the strong stability of scalar difference equations of continuous time in which the delays are sums of a number of independent parameters tau_i, i = 1, 2, . . . ,K. The characteristic quasipolynomial of such an equation is a multilinear function of exp(-tau_i s). It is known that the characteristic quasipolynomial of any difference equation set in the form of one-delayper- scalar-channel (ODPSC) model is also in such a multilinear form. However, it is shown in this article that some multilinear forms of quasipolynomials are not characteristic quasipolynomials of any ODPSC difference equation set. The equivalence …

Strong Stability Of A Class Of Difference Equations Of Continuous Time And Structured Singular Value Problem, Qian Ma, Keqin Gu, Narges Choubedar

SIUE Faculty Research, Scholarship, and Creative Activity

This article studies the strong stability of scalar difference equations of continuous time in which the delays are sums of a number of independent parameters τi, i = 1, 2, . . . , K. The characteristic quasipolynomial of such an equation is a multilinear function of e−τis. It is known that the characteristic quasipolynomial of any difference equation set in the form of one-delay-per-scalar-channel (ODPSC) model is also in such a multilinear form. However, it is shown in this article that some multilinear forms of quasipolynomials are not characteristic quasipolynomials of any ODPSC difference equation set. The equivalence between …

Discrete-Time Adaptive Control Algorithms For Rejection Of Sinusoidal Disturbances, Mohammadreza Kamaldar

Theses and Dissertations--Mechanical and Aerospace Engineering

We present new adaptive control algorithms that address the problem of rejecting sinusoids with known frequencies that act on an unknown asymptotically stable linear time-invariant system. To achieve asymptotic disturbance rejection, adaptive control algorithms of this dissertation rely on limited or no system model information. These algorithms are developed in discrete time, meaning that the control computations use sampled-data measurements. We demonstrate the effectiveness of algorithms via analysis, numerical simulations, and experimental testings. We also present extensions to these algorithms that address systems with decentralized control architecture and systems subject to disturbances with unknown frequencies.

Real Time And High Fidelity Quadcopter Tracking System, Tyler Mckay Hall

Computer Engineering

This project was conceived as a desired to have an affordable, flexible and physically compact tracking system for high accuracy spatial and orientation tracking. Specifically, this implementation is focused on providing a low cost motion capture system for future research. It is a tool to enable the further creation of systems that would require the use of accurate placement of landing pads, payload acquires and delivery. This system will provide the quadcopter platform a coordinate system that can be used in addition to GPS.

Field research with quadcopter manufacturers, photographers, agriculture and research organizations were contact and interviewed for information …

Ground Station Tracking System, Garret Hilton, Carter Mciver, Steven Hamby, Trevor Gahl, Casey Coffman, David Schwehr

2017 Academic High Altitude Conference

One of the Eclipse Ballooning Project’s main goals was to stream live video of the eclipse to the internet. To accomplish this task a tracking antenna was built to follow the balloon payload. As an added challenge, the task had to be completed on a budget. The “ground station” is the center for communication between the payload and user. This system utilizes GPS position reports from the payload via the iridium network to determine the balloons position. The computer algorithm takes in additional GPS and IMU data from the ground station to determine a relative heading to orientate the antenna …

P26. Global Exponential Stabilization On So(3), Soulaimane Berkane

Western Research Forum

Global Exponential Stabilization on SO(3)

Autonomous Quadrotor Collision Avoidance And Destination Seeking In A Gps-Denied Environment, Thomas C. Kirven

Theses and Dissertations--Mechanical and Aerospace Engineering

This thesis presents a real-time autonomous guidance and control method for a quadrotor in a GPS-denied environment. The quadrotor autonomously seeks a destination while it avoids obstacles whose shape and position are initially unknown. We implement the obstacle avoidance and destination seeking methods using off-the-shelf sensors, including a vision-sensing camera. The vision-sensing camera detects the positions of points on the surface of obstacles. We use this obstacle position data and a potential-field method to generate velocity commands. We present a backstepping controller that uses the velocity commands to generate the quadrotor's control inputs. In indoor experiments, we demonstrate that the …

Indoor Mapping Drone, Benjamin J. Plevny, Andrew Armstrong, Miguel Lopez, Davidson Okpara

Williams Honors College, Honors Research Projects

This project addresses the need for an autonomous indoor mapping system that will create a 3D map of an unknown physical environment in real time. The aerial system moves and avoids obstacles autonomously, without the need for human remote control or observation. An aerial system produces a map of an unknown indoor environment by transmitting data received from the aerial device’s sensors. The transmission occurs over a wireless channel from the aerial device to a remote server for processing and storage of the data. As the transmission is done in real time, the aerial system does not require hardware for …

A Radial Basis Function Method For Solving Optimal Control Problems., Hossein Mirinejad

Electronic Theses and Dissertations

This work presents two direct methods based on the radial basis function (RBF) interpolation and arbitrary discretization for solving continuous-time optimal control problems: RBF Collocation Method and RBF-Galerkin Method. Both methods take advantage of choosing any global RBF as the interpolant function and any arbitrary points (meshless or on a mesh) as the discretization points. The first approach is called the RBF collocation method, in which states and controls are parameterized using a global RBF, and constraints are satisfied at arbitrary discrete nodes (collocation points) to convert the continuous-time optimal control problem to a nonlinear programming (NLP) problem. The …

Small Satellite Noncommutative Rotation Sequence Attitude Control Using Piezoelectric Actuators, Joshua L. Evans

Theses and Dissertations--Electrical and Computer Engineering

Attitude control remains one of the top engineering challenges faced by small satellite mission planning and design. Conventional methods for attitude control include propulsion, reaction wheels, magnetic torque coils, and passive stabilization mechanisms, such as permanent magnets that align with planetary magnetic fields. Drawbacks of these conventional attitude control methods for small satellites include size, power consumption, dependence on external magnetic fields, and lack of full control authority. This research investigates an alternative, novel approach to attitude-control method for small satellites, utilizing the noncommutative property of rigid body rotation sequences. Piezoelectric bimorph actuators are used to induce sinusoidal small-amplitude satellite …

Cooperative 3-D Map Generation Using Multiple Uavs, Andrew Erik Lawson

University Scholar Projects

This report aims to demonstrate the feasibility of building a global 3-D map from multiple UAV robots in a GPS-denied, indoor environment. Presented are the design of each robot and the reasoning behind choosing its hardware and software components, the process in which a single robot obtains a individual 3-D map entirely onboard, and lastly how the mapping concept is extended to multiple robotic agents to form a global 3-D map using a centralized server. In the latter section, this report focuses on two algorithms, Online Mapping and Map Fusion, developed to facilitate the cooperative approach. A limited selection …

Identification Of Hydrodynamic Forces Developed By Flapping Fins In A Watercraft Propulsion Flow Field, Erdem Aktosun

LSU New Orleans Theses and Dissertations

In this work, the data analysis of oscillating flapping fins is conducted for mathematical model. Data points of heave and surge force obtained by the CFD (Computational Fluid Dynamics) for different geometrical kinds of flapping fins. The fin undergoes a combination of vertical and angular oscillatory motion, while travelling at constant forward speed. The surge thrust and heave lift are generated by the combined motion of the flapping fins, especially due to the carrier vehicle’s heave and pitch motion will be investigated to acquire system identification with CFD data available while the fin pitching motion is selected as a function …

Filtered-Dynamic-Inversion Control For Fixed-Wing Unmanned Aerial Systems, Jon Mullen

Theses and Dissertations--Mechanical and Aerospace Engineering

Instrumented umanned aerial vehicles represent a new way of measuring turbulence in the atmospheric boundary layer. However, autonomous measurements require control methods with disturbance-rejection and altitude command-following capabilities. Filtered dynamic inversion is a control method with desirable disturbance-rejection and command-following properties, and this controller requires limited model information. We implement filtered dynamic inversion as the pitch controller in an altitude-hold autopilot. We design and numerically simulate the continuous-time and discrete-time filtered-dynamic-inversion controllers with anti-windup on a nonlinear aircraft model. Finally, we present results from a flight experiment comparing the filtered-dynamic-inversion controller to a classical proportional-integral controller. The experimental results show …

Identifiability Of Additive Actuator And Sensor Faults By State Augmentation, Suresh M. Joshi, Oscar R. Gonzalez, Jason M. Upchurch

Electrical & Computer Engineering Faculty Publications

A class of FDI (fault detection and identification) methods for bias-type actuator and sensor faults was explored from the point of view of fault identifiability. The methods use banks of Kalman-Bucy filters (KBFs) to detect faults, determine the fault pattern, and estimate the fault values. A complete characterization of conditions for identifiability of bias-type actuator faults, sensor faults, and simultaneous actuator and sensor faults was presented. It was shown that FDI of simultaneous actuator and sensor faults is not possible using these methods when all sensors have unknown biases. The fault identifiability conditions were demonstrated via numerical examples. The analytical …

Identifiability Of Additive, Time-Varying Actuator And Sensor Faults By State Augmentation, Jason M. Upchurch

Electrical & Computer Engineering Theses & Dissertations

Faults in dynamical systems can have serious safety and reliability implications. For example, actuator and sensor faults have been factors in past incidents and mishaps in many aerospace systems. A large body of research is devoted to developing methods to detect and identify actuator and sensor faults in such systems.

One fault detection and identification menthol employs state augmentation, whereby a set of time-varying faults of interest are modeled as outputs of exogenous linear, time-invariant systems and augmented to the state of the nominal system model. The resulting model represents the system dynamics due to a particular actuator-sensor fault configuration. …

Low-Cost Imu Implementation Via Sensor Fusion Algorithms In The Arduino Environment, Brandon Mccarron

Aerospace Engineering

A multi-phase experiment was conducted at Cal Poly in San Luis Obispo, CA, to design a low-cost inertial measurement unit composed of a 3-axis accelerometer and 3-axis gyroscope. Utilizing the growing microprocessor software environment, a 3-axis accelerometer and 3-axis gyroscope simulated 6 degrees of freedom orientation sensing through sensor fusion. By analyzing a simple complimentary filter and a more complex Kalman filter, the outputs of each sensor were combined and took advantage of the benefits of both sensors to improved results. Gyroscopic drift was removed in the pitch and roll axes using the Kalman filter for both static and dynamic …

An Attitude Determination System With Mems Gyroscope Drift Compensation For Small Satellites, Maxwell Bezold

Theses and Dissertations--Electrical and Computer Engineering

This thesis presents the design of an attitude determination system for small satellites that automatically corrects for attitude drift. Existing attitude determination systems suffer from attitude drift due to the integration of noisy rate gyro sensors used to measure the change in attitude. This attitude drift leads to a gradual loss in attitude knowledge, as error between the estimated attitude and the actual attitude increases.

In this thesis a Kalman filter is used to complete sensor fusion which combines sensor observations with a projected attitude based on the dynamics of the satellite. The system proposed in this thesis also utilizes …

Visual Attitude Propagation For Small Satellites, Samir Ahmed Rawashdeh

Theses and Dissertations--Electrical and Computer Engineering

As electronics become smaller and more capable, it has become possible to conduct meaningful and sophisticated satellite missions in a small form factor. However, the capability of small satellites and the range of possible applications are limited by the capabilities of several technologies, including attitude determination and control systems. This dissertation evaluates the use of image-based visual attitude propagation as a compliment or alternative to other attitude determination technologies that are suitable for miniature satellites. The concept lies in using miniature cameras to track image features across frames and extracting the underlying rotation.

The problem of visual attitude propagation as …

Aether, Thomas Cameron, Kristine Colton, Daren Childers

Electrical Engineering

Aether is a RC-style autonomous air vehicle that utilizes GPS positioning along with a wireless communication system to achieve a computer-controlled flight.

This report will incorporate the acquisition, design, integration, implementation and testing phases of the UAV development. Furthermore a discussion of troubleshooting as well as improvements for future projects will be included.

Modeling Of A Gyro-Stabilized Helicopter Camera System Using Neural Networks, Nicholas Joseph Layshot

Master's Theses

On-board gimbal systems for camera stabilization in helicopters are typically based on linear models. Such models, however, are inaccurate due to system nonlinearities and complexities. As an alternative approach, artificial neural networks can provide a more accurate model of the gimbal system based on their non-linear mapping and generalization capabilities.

This thesis investigates the applications of artificial neural networks to model the inertial characteristics (on the azimuth axis) of the inner gimbal in a gyro-stabilized multi-gimbal system. The neural network is trained with time-domain data obtained from gyro rate sensors of an actual camera system. The network performance is evaluated …

Fault-Injection Experiment For The Statistical Characterization Of Faults In Avionics Communication System, Amy M. Yates

Electrical & Computer Engineering Theses & Dissertations

Since flight control systems perform safety-critical functions, it is important to understand the possible effects on the closed-loop dynamical system's performance caused by these faults. The purpose of this project is to design the software and hardware needed to add fault-injection and monitoring capabilities to ROBUS-2, a flight communication system. ROBUS-2 is the current version of the fault-tolerant computer communication system used by the Scalable Processor-Independent Design for Enhanced Reliability (SPIDER), a general-purpose fault-tolerant integrated modular architecture (IMA) developed at the NASA Langley Research Center. The major components of SPIDER include processing elements (PEs) to perform calculations, bus interface units …

Adverse Elevator Effect In Landing Flare, Nihad E. Daidzic

Aviation Department Publications

No abstract provided.

Modeling And Analysis Of Low Earth Orbit Satellite And Ground Station Data Exchange Topology, Ersin Kocoglu

Mechanical & Aerospace Engineering Theses & Dissertations

In order to utilize space effectively, the primary function of satellite control in orbit around the Earth must be accomplished. This controlling process includes two main segments, ground stations serving as the controller units and orbiting satellites as the units to be controlled. This thesis explores a topological data exchange model that contains one satellite and multiple ground stations. The model is implemented in digital computer software. This model has multiple purposes and can be used to simulate satellite passes over ground stations and can also be used to predict communication time and the amount of transferred data. The model …

Preliminary Electrical Designs For Ctex And Afit Satellite Ground Station, Arthur L. Morse

Theses and Dissertations

This thesis outlines the design of the electrical components for the space-based ChromoTomography Experiment (CTEx). CTEx is the next step in the development of high-speed chromotomography at the Air Force Institute of Technology. The electrical design of the system is challenging due to the large amount of data that is acquired by the imager and the limited resources that is inherent with space-based systems. Additional complication to the design is the need to know the angle of a spinning prism that is in the field of view very precisely for each image. Without this precise measurement any scene that is …

Model-Based Control Using Model And Mechanization Fusion Techniques For Image-Aided Navigation, Constance D. Hendrix

Theses and Dissertations

Unmanned aerial vehicles are no longer used for just reconnaissance. Current requirements call for smaller autonomous vehicles that replace the human in high-risk activities. Many times these activities are performed in GPS-degraded environments. Without GPS providing today's most accurate navigation solution, autonomous navigation in tight areas is more difficult. Today, image-aided navigation is used and other methods are explored to more accurately navigate in such areas (e.g., indoors). This thesis explores the use of inertial measurements and navigation solution updates using cameras with a model-based Linear Quadratic Gaussian controller. To demonstrate the methods behind this research, the controller will provide …

Multivariable Flight Control Design Tool Incorporating Gain And Phase Root Locus, Yong Ki Yoon

Mechanical & Aerospace Engineering Theses & Dissertations

A challenging problem in flight control system design for highly maneuverable aircraft is the coordinated control of the lateral-directional axes. Design goals are based on desired flying qualities giving an indication of whether the response to pilot inputs will be acceptable. Satisfying these closed-loop design objectives employing a computerized flight control system requires multiple feedback and crossfeed paths which operate in a well coordinated fashion. Contemporary control design tools, which close all loops simultaneously, have addressed this problem for several decades. Concerns associated with these strategies are the complicated mathematical relationships between the designer inputs and resulting closed-loop properties, and …

Towards A Metric For The Assessment Of Safety Critical Control Systems, Oscar R. Gonzalez, Jorge R. Chavez-Fuentes, W. Steven Gray

Electrical & Computer Engineering Faculty Publications

There is a need for better integration of the fault tolerant and the control designs for safety critical systems such as aircraft. The dependability of current designs is assessed primarily with measures of the interconnection of fault tolerant components: the reliability function and the mean time to failure. These measures do not directly take into account the interaction of the fault tolerant components with the dynamics of the aircraft. In this paper, a first step to better integrate these designs is made. It is based on the observation that unstable systems are intrinsically unreliable and that a necessary condition for …