Controls and Control Theory Commons^™

System Integration And Validation Of The Cal Poly Spacecraft Attitude Dynamics Simulator Mk. Iv, Bricen S. Rigby

Master's Theses

The Cal Poly Spacecraft Attitude Dynamics Simulator (SADS) is an ongoing project that seeks to enable the simulation and validation of sensors, actuators, and control logic related to spacecraft attitude control. The SADS platform rests atop a spher- ical air-bearing device which allows for nearly frictionless rotation in all three axes. The orientation of the platform is controlled by four reaction wheels arranged in a pyramidal configuration. Over the past few years, there have been significant updates to the reaction wheel subsystem, as well as requests for a more capable central com- puter. Therefore, a new system architecture for the …

Robust Real-Time Uav Target Tracking With Onboard Vision-Based Yaw Control, Rylan Malarchick, Jose Castelblanco, Enrique Amaya, Carmen Dimario, Graysen Brinkman, Chirag Kumar, Kiwon Yoon, Sajid Berhane

Beyond: Undergraduate Research Journal

Autonomous tracking of agile unmanned aerial vehicles (UAVs) presents significant challenges for real-time perception and control systems. This work presents AIRHOUND (Autonomous Intelligent Rotorcraft for Hostile Object Unified Navigation and Detection), a UAV platform implementing vision-based yaw tracking through a modular ROS2 software architecture. The system employs YOLOv8 object detection optimized with NVIDIA TensorRT for embedded deployment on an NVIDIA Jetson Orin companion computer. Detected targets are processed through a geometric tracking module that converts pixel coordinates to angular yaw errors using pinhole camera intrinsics, with a proportional controller generating rate-limited yaw commands. These commands are streamed to a PX4 …

Mass - Modular Acoustic Suppression System, Julia Megargle, Michael A. Milner, Lucas Kaemmererer, Jonathan Corvera, Gabriel Choi, Emmi Cayer

Mechanical Engineering

The Modular Acoustic Suppression System (MASS) is a mass tuned damper that reverberates a membrane atop a cavity to absorb select acoustic frequencies produced by the Environmental Control and Life Support Systems (ECLSS) within NASA's Artemis Human Lander. The height of the reverberation chamber is adjusted to mitigate a range of varying tonal frequencies within the human lander.

Safe Control Design For Quadruped Locomotion In Unstructured Environments Using Linear Transfer Operators, Sriram Sundar Krishnamoorthy Shankara Narayanan

All Dissertations

Deploying quadruped robots in unstructured, obstacle-rich environments requires control and planning methods that remain safe and reliable despite complex terrain geometry, limited sensing, and inevitable modeling errors. This thesis develops operator-theoretic tools for safe control design of robotic systems using linear transfer operators, with a focus on quadruped locomotion in unstructured environments. The central goal is to develop a unified operator-theoretic framework for safe control design based on the Perron–Frobenius (P–F) and Koopman operators. In particular, the thesis leverages \emph{density functions} to develop safe navigation frameworks in the dual space of densities. In the operator-theoretic perspective, the P–F operator governs …

The Pid-Based Three Quadcopter Uavs Formation Control Under External Disturbance, Vo Van An, Trinh Luong Mien

Makara Journal of Technology

This paper presents the design and evaluation of a formation control strategy for three quadcopter UAVs, based on a PID controller in a leader–follower structure, under the influence of external disturbances. Each UAV employs a six-degree of-freedom dynamic model and utilises a cascade PID control architecture, in which the inner control loop stabilises the attitude. In contrast, the outer control loop regulates position and maintains the formation. The PID parameters are tuned using the Ziegler–Nichols method to ensure simple implementation and low computational cost. The performance of the control system is evaluated through simulations in the MATLAB environment for two …

Automation And Habitat Development For A Space Based Marine Life Environment, Logan Trimmer, Alexander Hang

Harrisburg University Other Works

This project was a cross-collaboration between the Environmental Sciences and Advanced Manufacturing and Robotics programs for the company Monolith Space.

The goal of this project was to design an autonomous system to be able to track qualities of water in an aquaculture system designed to be sent to space.

Graph Based Planning With Guarantees, Trazon Tyrik Jimerson

Mechanical Engineering ETDs

This thesis presents two graph-based methods with formal guarantees for motion planning and routing. First, the invariant-set motion planner (ISMP), which uses constraint admissible positive invariant (CAPI) sets of closed-loop dynamics, is adapted for spacecraft attitude planning to avoid moving keep-out zones. Contributions include time bounds for maneuvers via exponential stability, a single-stage reachability graph from one-step backward reachable CAPI sets, and its multi-stage expansion to certify node safety over time. Simulations verify safe attitude control with moving obstacles. Second, we formulate a convex optimization problem over a network for evacuation planning with operational constraints such as helicopter capacity and …

Parameter Informed Reinforcement Learning For Vehicle System Identification, Nathan Schaff

Doctoral Dissertations and Master's Theses

Accurate system identification is essential for modeling and controlling vehicle dynamics. This dissertation explores the application of Parameter Informed Reinforcement Learning (PIRL) as a novel approach to system identification (SYSID). PIRL integrates prior system knowledge, such as physical parameters, into reinforcement learning (RL) frameworks to improve estimation accuracy. The study begins with an overview of traditional SYSID methods and then introduces PIRL as a modification of standard RL. The research applies PIRL to short-period aircraft dynamics, demonstrating its effectiveness in both offline and online learning frameworks. The dissertation then further explores PIRL’s utility in an indirect model reference adaptive control …

Orbital Maneuvers And Interplanetary Trajectory Design Via Reinforcement Learning, Roberto Cuéllar Rangel

Doctoral Dissertations and Master's Theses

This dissertation investigates the application of reinforcement learning (RL) to the design and optimization of low-thrust spacecraft trajectories, with an emphasis on autonomy, adaptability, and robustness in the presence of system uncertainties and unmodeled perturbations. Classical approaches to low-thrust trajectory design are predominantly grounded in optimal control theory, which relies on the availability of precise dynamical models and often requires problem-specific reformulation and solver tuning. While optimal control methods offer high accuracy under deterministic conditions, their sensitivity to stochastic disturbances and computational limitations in highly nonlinear or uncertain environments pose significant challenges for future autonomous space missions.

To address these …

Pressure Switch Tester, Michael Starasinich, Andrew Dobson, Jordan Huschen, Mitchell Smith, Melvin Brown Iii

Honors Capstones

Abstract—- The Pressure Switch Test Stand is a comprehensive and automated testing solution designed to streamline the actuation and validation of simultaneously. At the core of the system is a PLC-controlled architecture that enables precise control and simulation of pressure conditions, replicating real-world scenarios to ensure accurate and reliable switch performance.

This test stand integrates robust mechanical fixtures, a reliable pneumatic control system, custom-designed electrical circuits, and a modular software interface, working in unison to deliver consistent and high-fidelity testing outcomes. Each pressure switch undergoes a sequence of pressure ramps and holds, with the system continuously monitoring switch states, activation …

Design Of An Active-Control Pressure Regulator For A Rocket, Seth Arkwright

Williams Honors College, Honors Research Projects

An electronically actuated pressure-regulation valve and controller are necessary for maintaining pressure levels in a pressure-fed liquid-fueled rocket engine. Mechanical regulators are too heavy and have unacceptably high-pressure variation throughout the operation of a dynamic system like a rocket. Developing an electronic pressure regulator using a PID controller is a method by which a reliable, accurate, and lightweight flow regulator can be built for use on a rocket vehicle. This work will outline the development of flow simulations, PID controller, physical valve hardware, and initial testing.

Theory And Algorithms To Learn, Propagate, And Exploit Uncertainty For Stochastic Optimal Control Of Dynamical Systems, Vignesh Sivaramakrishnan

Electrical and Computer Engineering ETDs

Non-Gaussian uncertainty frequently arises in learning and control problems involving stochastic dynamical systems, particularly in autonomous vehicles, UAVs, satellites, and robotics. In this dissertation, we propose a new framework that leverages characteristic functions that provides a frequency-domain representation of random variables. The dissertation is structured into three key areas. First, we address model-based stochastic optimal control for linear systems with non-Gaussian noise, demonstrating that characteristic functions can be used to enforce chance constraints and control systems toward desired distributions. Second, we explore data-driven stochastic control, utilizing empirical characteristic functions to handle systems with unknown disturbances. In addition, we derive several …

Koopman-Based Modeling For Nonlinear Control Of Multirotor Uavs, Simone Martini

Electronic Theses and Dissertations

This PhD dissertation focuses on adopting the emerging Koopman Operator theory for modeling and nonlinear control of multirotor UAVs, focusing specifically on quadrotors for proof-of-concept demonstration purposes.

The Koopman Operator theory is based on the foundation that nonlinear dynamics in the state space may be represented as a linear evolution of some functions in the state space. Thus, using appropriately defined and possibly nonlinear functions of the state variables, called observables, as a new and maybe infinite set of coordinates that are referred to as lifted space, the original nonlinear dynamics appear to be linear. The implications of this theory …

State Omniscience For Cooperative Local Catalog Maintenance Of Close Proximity Satellite Systems, Chris Hays

Doctoral Dissertations and Master's Theses

Resiliency in multi-agent system navigation is reliant on the inherent ability of the system to withstand, overcome, or recover from adverse conditions and disturbances. In large part, resiliency is achieved through reducing the impact of critical failure points to the success and/or performance of the system. In this view, decentralized multi-agent architectures have become an attractive solution for multi-agent navigation, but decentralized architectures place the burden of information acquisition directly on the agents themselves. In fact, the design of distributed estimators has been a growing interest to enable complex multi-sensor/multi-agent tasks. In such scenarios, it is important that each local …

Trustable Adaptive Controllers For Multi-Agent Systems With Actuator Dynamics, Atahan Kurttisi

Doctoral Dissertations and Master's Theses

Multi-agent systems have become a powerful tool for a wide range of applications due to the effective and cheap solutions they offer. Especially during the last decade, they have impacted a wide array of civilian and military applications (e.g., surveillance, reconnaissance, and payload transportation). However, they suffer system anomalies due to the operational and material conditions, which yields degraded performance or even instability. Hence, this dissertation investigates the distributed adaptive control design process for uncertain multi-agent systems with scalar and high-order dynamics in the presence of unknown control effectiveness and actuator dynamics. First, it provides an approach for driving a …

Study Of A Multi-Agent Containment Problem Under Communication Constraints And Defense From Malicious Agents, Braulio Mora

Mechanical and Aerospace Engineering Theses - Archive

This thesis investigates a multi-agent containment problem where a fast evader, moving at a constant speed and heading, attempts to escape a circular containment region. A team of slow pursuers possess a nonzero capture radius and seek to capture the evader before escape. The research addresses two primary scenarios: one involving the team of pursuers, with no communication network, being constrained to the edge of the containment region, and the second involving a team of pursuers, with a communication network, not being constrained to the edge of the containment region. Both scenarios study the influence of malicious agents in the …

Nonlinear Guidance And Control Of Unmanned Aerial Manipulators For Delivering A Payload On A Moving Platform, Ravi Gyawali

Mechanical and Aerospace Engineering Theses - Archive

Unmanned Aerial manipulators (UAMs) are a class of Unmanned Aerial Vehicles (UAVs) equipped with a manipulator. By combining the aerial mobility of a UAV with a manipulator's dexterity, these hybrid systems can perform a wide range of complex tasks while reducing risks and costs. As a result, they are increasingly being utilized for military, industrial, and agricultural applications.

The thesis presents a novel approach for a multi-UAM system to collaboratively deliver a payload on a stationary or maneuvering platform. A sliding-mode-based guidance law, sourced from existing literature, is integrated with a combined control technique for the UAVs and their respective …

On Uncertainty For Ill-Posed Robot Decision Problems, Jared Joseph Beard

Graduate Theses, Dissertations, and Problem Reports (ETD)

As robots adopt more real world responsibilities, they will be expected to solve more complicated problems. In some cases limited prior knowledge will result in unmodelled environmental conditions; in others, multiple users may have competing perspectives on how to frame a decision problem. Many existing frameworks, namely Markov decision processes (MDP) presuppose users have identified a specific problem with models sufficient to solve or learn a problem. If we wish to extend MDPs to novel problems or those heavily dependent on user feedback, autonomous decision makers must be able to identify limitations in how a given problem is framed and …

External Runtime Execution Monitoring Of A Cyber Physical System Via Trace Interfaces, Peter Vaughan Truslow

Theses and Dissertations

In the past two decades, Unmanned Aerial Systems have progressed from expensive military hardware or one-off custom builds, to include off-the-shelf drones that can be purchased for a rather affordable price and flown by nearly anyone. As the technology and performance have improved, the door is opened to applications that require operation in environments where the consequences for failure are high, such as operating in the navigable airspace or in urban environments, or with human passengers. This requires a great deal of trust in the reliability and integrity of the control systems of the aircraft. A method of monitoring the …

Controlled Manipulation And Transport By Microswimmers In Stokes Flows, Jake Buzhardt

All Dissertations

Remotely actuated microscale swimming robots have the potential to revolutionize many aspects of biomedicine. However, for the longterm goals of this field of research to be achievable, it is necessary to develop modelling, simulation, and control strategies which effectively and efficiently account for not only the motion of individual swimmers, but also the complex interactions of such swimmers with their environment including other nearby swimmers, boundaries, other cargo and passive particles, and the fluid medium itself. The aim of this thesis is to study these problems in simulation from the perspective of controls and dynamical systems, with a particular focus …

Safe Navigation Of Quadruped Robots Using Density Functions, Andrew Zheng

All Theses

Safe navigation of mission-critical systems is of utmost importance in many modern autonomous applications. Over the past decades, the approach to the problem has consisted of using probabilistic methods, such as sample-based planners, to generate feasible, safe solutions to the navigation problem. However, these methods use iterative safety checks to guarantee the safety of the system, which can become quite complex. The navigation problem can also be solved in feedback form using potential field methods. Navigation function, a class of potential field methods, is an analytical control design to give almost everywhere convergence properties, but under certain topological constraints and …

Hardware-In-The-Loop Reaction Wheel Testbed With Camera Vision, Abigail Romero, Harvey Perkins, Stephen Kwok-Choon

College of Engineering Summer Undergraduate Research Program

Reaction wheels are widely used in aerospace systems as a method of attitude control. This research was focused on the design, development, and testing of a hardware-in-the-loop reaction wheel testbed that can be used for research and teaching applications related to satellite navigation and control. This project successfully utilized commercial off-the-shelf components to develop a reaction wheel capable of controlling the orientation of a freely rotating platform, as well as tracking objects using computer vision.

Integrated Energy-Aware Motion Planning And Charge Scheduling Of Unmanned Aerial Vehicles, Hayleyesus Alemayehu

All Theses

The growing demand for unmanned aerial vehicles (UAVs) is driven by their operational convenience, cost-effectiveness, availability, and adaptability to various scenarios. In energy-constrained environments, optimizing energy consumption and ensuring a continuous power supply for UAVs is crucial for mission success. The objective of this thesis is to address this issue by integrating energy-aware motion planning and charge scheduling for UAVs by utilizing a charger hosted on an unmanned ground vehicle (UGV), whose rendezvous locations and routes are jointly computed to minimize overall energy consumption.

This thesis proposes a hierarchical trajectory and control framework comprising local and global planners for each …

Data-Driven Porosity Prediction For Directed Energy Deposition, Georgia E. Kaufman

Electrical and Computer Engineering ETDs

Stochastic flaw formation leading to poor print quality is a major obstacle to the utility of directed energy deposition (DED), a laser and metal powder-based additive manufacturing technology for construction and repair of custom metal parts. While melt pool temperature variability is known to be a major factor in flaw formation, control schemes to decrease flaw formation are limited by a lack of physics-based models that fully and accurately describe DED. In this work, a stochastic reachability analysis with a data-driven model based on thermal images of the melt pool was conducted to determine the likelihood of violating melt pool …

Crazyflie 2.1 Quadcopter Nonlinear System Identification, Nhat V. Nguyen, Hope Storro, John Plimpton

2023 Symposium

Quadcopters (quad) are used widely in many industries with crucial applications such as infrastructure inspection or package delivery. The Crazyflie 2.1 quad from Bitcraze provides an excellent platform for research and development. In this project, our goal is to perform system identification on the Crazyflie to propose a complete model. A gray box method is explored, which includes leveraging the parameters that are already known, to develop a set of equations. Through theory, simulations, and measurements, a complete quadcopter model is developed.

Instrumented Control Column For Optionally Piloted Aircraft, Andrew J. Klein

Electrical Engineering

Natilus, an aerospace company that is rapid-prototyping optionally piloted aircraft (OPA) for the shipping industry, needs a system that retrieves control column position data in order to manipulate flight simulator parameters in software. At present, a universally compatible system for all aircraft does not exist. Typically, established aerospace companies will sink significant time and money into developing proprietary systems for control column data retrieval as every aircraft is unique in its layout and linkage design. However, as a startup developing their first aircraft, Natilus does not have the privilege of modifying an existing sensor system to work with their HIL …

Novel Locomotion Methods In Magnetic Actuation And Pipe Inspection, Adam Cox

Mechanical Engineering Research Theses and Dissertations

There is much room for improvement in tube network inspections of jet aircraft. Often, these inspections are incomplete and inconsistent. In this paper, we develop a Modular Robotic Inspection System (MoRIS) for jet aircraft tube networks and a corresponding kinematic model. MoRIS consists of a Base Station for user control and communication, and robotic Vertebrae for accessing and inspecting the network. The presented and tested design of MoRIS can travel up to 9 feet in a tube network. The Vertebrae can navigate in all orientations, including smooth vertical tubes. The design is optimized for nominal 1.5" outside diameter tubes. We …

On-Board Artificial Intelligence For Failure Detection And Safe Trajectory Generation, Eduardo Morillo

Doctoral Dissertations and Master's Theses

The use of autonomous flight vehicles has recently increased due to their versatility and capability of carrying out different type of missions in a wide range of flight conditions. Adequate commanded trajectory generation and modification, as well as high-performance trajectory tracking control laws have been an essential focus of researchers given that integration into the National Air Space (NAS) is becoming a primary need. However, the operational safety of these systems can be easily affected if abnormal flight conditions are present, thereby compromising the nominal bounds of design of the system's flight envelop and trajectory following. This thesis focuses on …

Multi-Robot Symbolic Task And Motion Planning Leveraging Human Trust Models: Theory And Applications, Huanfei Zheng

All Dissertations

Multi-robot systems (MRS) can accomplish more complex tasks with two or more robots and have produced a broad set of applications. The presence of a human operator in an MRS can guarantee the safety of the task performing, but the human operators can be subject to heavier stress and cognitive workload in collaboration with the MRS than the single robot. It is significant for the MRS to have the provable correct task and motion planning solution for a complex task. That can reduce the human workload during supervising the task and improve the reliability of human-MRS collaboration. This dissertation relies …

Formation Control With Bounded Controls And Collision Avoidance: Theory And Application To Quadrotor Unmanned Air Vehicles, Zachary S. Lippay

Theses and Dissertations--Mechanical and Aerospace Engineering

This dissertation presents new results on multi-agent formation control and applies the new control algorithms to quadrotor unmanned air vehicles. First, this dissertation presents a formation control algorithm for double-integrator agents, where the formation is time varying and the agents’ controls satisfy a priori bounds (e.g., the controls accommodate actuator saturation). The main analytic results provide sufficient conditions such that all agents converge to the desired time-varying relative positions with one another and the leader, and have a priori bounded controls (if applicable). We also present results from rotorcraft experiments that demonstrate the algorithm with time-varying formations and bounded controls. …