Electrical and Computer Engineering Commons^™

A Dielectric Rod Antenna For Picosecond Pulse Stimulation Of Neurological Tissue, Ross A. Petrella, Karl H. Schoenbach, Shu Xiao

Bioelectrics Publications

A dielectrically loaded wideband rod antenna has been studied as a pulse delivery system to subcutaneous tissues. Simulation results applying 100-ps electrical pulse show that it allows us to generate a critical electric field for biological effects, such as brain stimulation, in the range of several centimeters. In order to reach the critical electric field for biological effects, which is similar to 20 kV/cm, at a depth of 2 cm, the input voltage needs to be 175 kV. The electric field spot size in the brain at this position is similar to 1 cm(2). Experimental studies in free space with …

Simulation Of Gan Based Mis Varactor, Bojidha Babu

Theses and Dissertations

This work deals with novel microwave switches based on III-Nitride varactors. RF switches, power limiters and other control devices are important components of various RF systems, such as wireless modules of laptops, tablets, cell phones etc., satellites communication systems, radars, multi-band wireless and aerospace communications, phased array antennas and so worth. Traditional RF switches are fabricated using pin diodes or MEMS, Si MOSFETs or GaAs HEMTs. These devices have a number of fundamental limitations. Si or GaAs based devices suffer from a low breakdown voltage and cannot handle high RF power. Pin-diodes require large forward currents and do not allow …

Applications Of Impedance Identification To Electric Ship System Control And Power Hardware-In-The-Loop Simulation, Jonathan Siegers

Theses and Dissertations

Recent advances in semiconductor technology, controls, and switching converter topologies have resulted in the increasing application of power electronics in power distribution systems. Power electronic enabled distribution systems have inspired a renewed interest in DC distribution architectures as an appealing alternative to traditional AC methods due to the significant performance and efficiency gains they offer. However, the notional power electronic based DC distribution system is a complex and extensively interconnected system consisting of multiple power converters. As a result, a number of system-level challenges related to stability arise due to interaction among multiple power converters. In addition, the power distribution …

Torque Accuracy Improvement Via Explicit Torque Feedback Control For Internal Combustion Spark Ignition Engines, Anwar Alkeilani

Wayne State University Dissertations

At the present time, both control and estimation accuracies of engine torque are causes for under-achieving optimal drivability and performance in today’s production vehicles. The major focus in this area has been to enhance torque estimation and control accuracies using existing open-loop torque control and estimation structures. Such an approach does not guarantee optimum torque tracking accuracy and optimum estimation accuracy due to air flow and efficiencies estimations errors. Furthermore, current approach overlooks the fast torque path tracking which does not have any related feedback. Recently, explicit torque feedback control has been proposed in the literature using either estimated or …

Designing And Simulation Of Various Class-F Radio-Frequency Power Amplifier, Varun Pundhir

Browse all Theses and Dissertations

In this thesis, the various kinds of Class-F radio frequency power amplifiers are discussed. The Class-F3 RFPA is the one which has been designed and analyzed. It consists of an RF choke, blocking capacitor and a loading network. The loading network consists of a tank circuit resonating at fundamental operating frequency and also a parallel resonator circuit tuned to third harmonic. For a better understanding of the operation of Class-F3 amplifier, we go back to Class-C amplifier and discuss it briefly. Here the design remains same, operating at conduction angles less than 180 degree. The design equations were used to …

Modeling, Simulation And Control Of Hybrid Electric Vehicle Drive While Minimizing Energy Input Requirements Using Optimized Gear Ratios, Sanjai Massey

Dissertations, Master's Theses and Master's Reports

This project was conducted to analyze (model and simulate) and optimize an electric motor based drive system to propel a typical passenger vehicle in an urban driving environment. Although there are many HEV and EV type systems on the market today, this paper chose the Toyota Prius HEV system as a baseline using a brushless AC motor.

Although a vehicle can be driven many ways, a more standardized Urban Dynamometer Driving Schedule, UDDS, was chosen to simulate real driving conditions. This schedule is determined by the US Environmental Protection Agency, EPA, and is intended to represent the city driving conditions …

Simulation Design For Photovoltaics Using Finite Difference Time Domain And Quadratic Complex Rational Function Methods, Jacob R. Duritsch, Haejun Chung, Peter Bermel

The Summer Undergraduate Research Fellowship (SURF) Symposium

Photovoltaics (PV) can in principle supply enough renewable energy to offset a great deal of fossil fuel usage. To achieve this transition, it is critical to develop improved PV cells with decreased material costs and improved efficiencies. This goal can be greatly facilitated by a tool simulating the absorption and efficiency of experimentally relevant 3-D PV designs made of realistic materials, including those that have not yet been discovered. By incorporating the quadratic complex rational function algorithm (QCRF) with the finite difference time domain methods (FDTD), simulations can include frequency response and optical properties, while allowing full customization of tandem …

Simulating Nanowires And Ultra-Thin Body Transistors Using Nemo5 On Nanohub.Org, Liang Yuan Dai, James E. Fonseca, Chu Yuan Chen, Gerhard Klimeck

The Summer Undergraduate Research Fellowship (SURF) Symposium

During the past twenty years, the most important aspects of semiconductor electronics have advanced into the nanometer range, resulting in exponential increases of microprocessor computing performance. As the size of electrical components continues to shrink, the cost of experimental research and industrial fabrication in this field has increased dramatically. Thus, the development of accurate nanoscale model simulations becomes necessary as a measure to decrease the high financial expenses of advancing semiconductor technology. This simulator supports atomistic modeling in order to provide an accurate description of the nanoscale devices, as current electrical components operate in the quantum regime and are affected …

Electron-Beam Patterning Of Teflon Af For Surface Plasmon Resonance Sensing, Mansoor A. Sultan

Theses and Dissertations--Electrical and Computer Engineering

Variable pressure electron beam etching and lithography for Teflon AF has been demonstrated. The relation between dose and etching depth is tested under high vacuum and water vapor. High resolution structures as small as 75 nm half-pitch have been resolved. Several simulation tools were tested for surface plasmon excitation. Grating based dual mode surface plasmon excitation has been shown numerically and experimentally.

Impact Of Large-Scale Installation Of Led Lamps In A Distribution System, Sohel Uddin, Hussain Sharef, Olav Krause, Azah Mohamed, Mohammad Abdul Hannan, Naz Niamul Islam

Turkish Journal of Electrical Engineering and Computer Sciences

The aim of this paper was to examine the utilization of a large number of nonlinear light emitting diode (LED) lamps in a distribution system and its impact on system power quality. Initially, harmonic and others electrical characteristics were identified by carrying out an experiment on four types of LED lamps available on the local market. On the basis of the identified characteristics, a new LED lamp model was developed in MATLAB Simulink. This model is called the time-dependent current source model and gives more accurate results than the fixed current source model. Then this model was applied to a …

Advancement And Validation Of A Plug-In Hybrid Electric Vehicle Model Utilizing Experimental Data From Vehicle Testing, Kevin Lloyd Snyder

Wayne State University Theses

The objective of the research into modeling and simulation was to provide an iterative improvement to the Wayne State EcoCAR 2 team's math-based design tools for use in evaluating different outcomes based on hybrid powertrain architecture tweaks, controls code development and testing. This thesis includes the results of the team's work in the EcoCAR 2 competition for university student teams to create and test a plug-in hybrid electric vehicle for reducing petroleum oil consumption, pollutant emissions, and Green House Gas (GHG) emissions.

Plant model validations and advancements brought the vehicle plant model directionally closer to the actual vehicle's experimental data …

Wind Energy Estimation Functions For Future Homes, Adel El-Shahat, Rami J. Haddad, Youakim Kalaani

Electrical & Computer Engineering: Faculty Publications

Wind energy is ideally suited for distributed generation systems to meet growing demand for electricity that find applications especially in developing countries. The motive of this study is to develop an efficient method to help identify and select the best sites to harvest the wind energy in Egypt. In this paper, a novel approach is proposed to estimate and appraise wind energy resources using Artificial Neural Network (ANN). To achieve this goal, an ANN-based algorithm was created and trained using relevant data collected from several wind monitoring posts installed across the country. Parameters such as latitude, longitude, elevation, and monthly …

Design Of Energy Storage Controls Using Genetic Algorithms For Stochastic Problems, Si Chen

Theses and Dissertations--Electrical and Computer Engineering

A successful power system in military applications (warship, aircraft, armored vehicle etc.) must operate acceptably under a wide range of conditions involving different loading configurations; it must maintain war fighting ability and recover quickly and stably after being damaged. The introduction of energy storage for the power system of an electric warship integrated engineering plant (IEP) may increase the availability and survivability of the electrical power under these conditions. Herein, the problem of energy storage control is addressed in terms of maximizing the average performance. A notional medium-voltage dc system is used as the system model in the study. A …

Computational Electronics For The 21st Century: Reflections On The Past, Present, And Future, Mark S. Lundstrom

Department of Electrical and Computer Engineering Faculty Publications

The author’s career has coincided with the development of numerical simulation into an essential component of semiconductor device technology research and development. We now have a sophisticated suite of simulation capabilities along with new challenges for 21st Century electronics. This talk presents a short history of the field and a description of the current state of the art, but it concentrates on lessons learned and thoughts about how computational electronics can continue to contribute effectively to the development of new electronic device technologies. The author will argue that electronics is changing, and that computational electronics can play a key role …

Multifrequency Averaging Of Hysteresis-Current-Controlled Dc-Dc Converters, Yingying Liu

Theses and Dissertations--Electrical and Computer Engineering

Multifrequency averaging is one of the widely used modeling and simulation techniques today for the analysis and design of power electronic systems. This technique is capable of providing the average behavior as well as the ripple behavior of power electronic systems. Hysteresis current control has fast response and internal current stability through controlling switches to maintain the current within a given hysteresis band of a given current command. However the state space variables in a hysteresis controlled system cannot be directly approached by multifrequency averaging method because of time varing switching frequency. In this thesis, a method of applying multifrequency …

Particle-In-Cell Based Parameter Study Of 12-Cavity, 12-Cathode Rising-Sun Relativistic Magnetrons For Improved Performance, Alireza Majzoobi, R. P. Joshi, A. A. Neuber, J. C. Dickens

Electrical & Computer Engineering Faculty Publications

Particle-in-cell simulations are performed to analyze the efficiency, output power and leakage currents in a 12-Cavity, 12-Cathode rising-sun magnetron with diffraction output (MDO). The central goal is to conduct a parameter study of a rising-sun magnetron that comprehensively incorporates performance enhancing features such as transparent cathodes, axial extraction, the use of endcaps, and cathode extensions. Our optimum results demonstrate peak output power of about 2.1 GW, with efficiencies of ~70% and low leakage currents at a magnetic field of 0.45 Tesla, a 400 kV bias with a single endcap, for a range of cathode extensions between 3 and 6 centimeters.

Added Mass Computation For Control Of An Open-Frame Remotely-Operated Vehicle: Application Using Wamit And Matlab, You-Hong Eng, Cheng-Siong Chin, Michael Wai-Shing Lau

Journal of Marine Science and Technology–Taiwan

In this paper, numerical modeling and testing of a complexshaped remotely-operated vehicle (ROV) are shown. The paper emphasizes on systematic modeling of hydrodynamic added mass using computational fluid dynamic software WAMITTM on the open frame ROV that is not commonly applied in practice. From initial design and prototype testing, a small-scale test using a free-decaying experiment is used to verify the theoretical models obtained from WAMITTM. Simulation results have shown to coincide with the experimental tests. The proposed method is able to determine the hydrodynamic added mass coefficients of the open frame ROV.

1d Phonon Bte Solver (Small Scale Heat Transport Simulation), Joseph A. Sudibyo, Amr Mohammed, Ali Shakouri

The Summer Undergraduate Research Fellowship (SURF) Symposium

In current technology, electronic devices shrink to the size of nanometers. The ability to accurately model heat transport to understand the thermal behavior of these small electronic devices becomes increasingly important. Since heat transport is very difficult to measure directly in small electronic devices, simulation becomes an effective means to model heat transport. A user-interactive simulation tool is created to model heat transport in small electronic devices of different lengths. Heat transport is modeled by solving one-dimensional Boltzmann transport equation (BTE) to obtain the transient temperature profile of a multi-length and multi-timescale thin film under constant temperature boundary condition or …

Simulation Of Plasmonic Waveguides Based On Long-Range Surface Plasmon Polaritons, Yugang Jing, Alexandra Boltasseva, Nathaniel Kinsey

The Summer Undergraduate Research Fellowship (SURF) Symposium

The demand for faster and smaller computing devices is growing larger and larger. In the recent decade, research has proven that plasmonic devices have exciting characteristics and performance for next generation on‑chip structures. However, most of these devices contain noble metals and are not CMOS compatible. This work numerically investigates the performance of plasmonic waveguide designs made of TiN, a CMOS compatible material with optical properties similar to gold. Through our work, we demonstrate that TiN nanophotonic devices can be useful for inter-chip connections. A series of simulations using COMSOL Multiphysics were performed to test the performance of these structures. …

Developing Compact Models For Passive Devices On Ibm 45nm Cmos Soi Technology, Yufei Feng, Yanfei Shen, Saeed Mohammadi

The Summer Undergraduate Research Fellowship (SURF) Symposium

The standard IBM 45 nm technology is widely adopted for industrial and academic purpose by integrates circuit designers. Original models provided by foundry are not accurate, which might cause inaccuracy in circuit simulations. Equivalent circuit models, using RLC elements to simulate electrical component, will effectively deliver their electrical performance. This study consists of four steps to construct these models. First, Cadence Virtuoso, the commercial circuit design software was used to run simulations and extract data for different device parameters. Second, analyzing tools, like Microsoft Excel or Matlab, are used to analyze the extracted data. Then, equations are written for each …

Thermal And Structural Modeling Of Electrochromics On Glass, Mahesh B. Manandhar

Electronic Theses and Dissertations

Advanced glazing is a type of window glazing that interacts with the surrounding environment to change its thermal and optical properties to create a more comfortable and energy efficient indoor environment. Electrochromics are one type of such advanced glazing materials that change their properties in response to an externally applied voltage controllable by the user or by automation.

The effectiveness of electrochromics depends upon how well it can keep off extreme temperature conditions from outdoors all year round as well as how structurally stable it can remain at such conditions. This research investigates the use of COMSOL, a finite element …

Verifying Molecular Dynamics Using Dielectric Spectroscopy, Joshua Dee Smith

Theses and Dissertations

The electrical properties of proteins in solution are important for their structure and function. Computational biophysics studies of proteins need accurate parameters to ensure that numerical simulations match physical reality. Past work in this eld has compared the electrical properties of proteins obtained from dielectric spectroscopy to numerical simulations of proteins in water with adjustment of pKa values to try to capture the inevitable changes in electrical conformation that will occur in a complex structure such as a folded protein. However, fundamental veri cation of the charge parameters of the amino acid building blocks in common molecular dynamics software packages …

Simulation Of A Smart Home Energy Management System With Dynamic Price Response, Jason Y. Chan, Qinran Hu

Pursuit - The Journal of Undergraduate Research at The University of Tennessee

With the continuing development of the smart grid combined with the fluctuating nature of the electricity market, the development of demand-side management with controllable loads have been greatly driven. With the amount of household loads in the residential sector, managing their energy usage has received lots of interest. This paper presents a simulation of a previously proposed hardware design of a smart home energy management system (SHEMS), focusing on the data collection and processing functions of the proposed design while implementing them onto standard household loads like an electric water heater and an electric vehicle charging station. It was found …

Design Of A Chart-Based Radar Simulator Augmented With A Multi-Agent Ship Traffic Simulation Platform, Shwu-Jing Chang, Yu-Ting Lai, Chun-Mai Hsu

Journal of Marine Science and Technology–Taiwan

This paper presents a radar simulation system developed under a request to deliver a radar and an Electronic Chart Display and Information System (ECDIS) for the navigation bridge of a ship maneuvering simulator. It is designed to dynamically generate radar image based on the electronic navigational chart database and sensor information to provide flexibility in navigation area for exercise and maintain consistency with other sensors or systems of the bridge, especially the ECDIS. Since the successful delivery of our study, the radar simulation system has been augmented with a Multi-Agent Ship Traffic (MAST) simulation platform and evolved into a versatile …

Development Of A Strapdown Inertial Navigation System Simulation Platform, Dah-Jing Jwo, Jyun-Han Shih, Chia-Sheng Hsu, Kai-Lun Yu

Journal of Marine Science and Technology–Taiwan

This paper presents a strapdown inertial navigation system (SINS) simulation platform. The numerical simulator solves the navigation equations in navigation frame where the quaternion vector is employed for attitude calculation. The measured quantities (angular body rates and specific force) are generated by the numerical simulator. The results are also confirmed with the navigation solutions given by a commercial inertial navigation system toolbox using the generated body angular rates and specific force of the SINS. The paper can provide the readers with further information for developing their own SINS simulation tools.

Characterization Of An Impulse Radiating Antenna In The Near Field, Chandra Barjracharya

Electrical & Computer Engineering Theses & Dissertations

The biological effects of intense sub-nanosecond pulses on tissues or cells are in the dielectric domain and not based on thermal loading as in the conventional microwave radiation, which may lead to an entirely new approach of modifying cell functions. Moreover, the resulting cell functional change may be detected with higher resolution by broadband, sub-nanosecond pulses than conventional narrowband systems. The delivery of intense sub-nanosecond pulses to near-field biological tissues, however, has not been studied, not mentioning the focal depth and volume. In this dissertation, for the first time, an impulse radiating antenna with a balanced feed structure is studied …

Computer Modeling And Simulation Of Implantable Medical Device Heating Due To Mri Gradient Coil Fields, Bryan David Stem

Open Access Theses

For patients with implantable medical devices, the ability to safely undergo MRI scanning is critical to ensuring the highest standard of care. The gradient coils of an MRI generate kilohertz frequency, time varying magnetic fields. These magnetic fields induce a voltage on the external case of metallic, implantable medical devices through electromagnetic induction. Since the magnetic field generated by a gradient coil is time varying, the induced voltage results in the flow of eddy currents which can cause heating effects. These heating effects have been successfully modeled using ANSYS Maxwell and ANSYS Mechanical software packages.

The multi-physics simulation and solution …

Enhancing Gan Led Efficiency Through Nano-Gratings And Standing Wave Analysis, Gabriel M. Halpin

Master's Theses

Improving energy efficient lighting is a necessary step in reducing energy consumption.Lighting currently consumes 17% of all U.S. residential and commercial electricity, but a report from the U.S. Office of Energy Efficiency and Renewable Energy projects that switching to LED lighting over the next 20 years will save 46% of electricity used in lighting.GaN LEDs are used for their efficient conversion of electricity to light, but improving GaN efficiency requires optically engineering the chip to extract more light.Total internal reflection limits GaN LED performance since light must approach the chip surface within 23.6° of normal to escape into air.This thesis …

An Algorithm To Recognize Multi-Stable Behavior From An Ensemble Of Stochastic Simulation Runs, Eduardo Monzon

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Synthetic biological designers are demanding tools to help with the design and verification process of new biological models. Some of the most common tools available aggregate multiple simulation results into one “clean” trajectory that hopefully is representative of the system’s behavior. However, for systems exhibiting multiple stable states, these techniques fail to show all the possible trajectories of the system. This work introduces a method capable of detecting the presence of more than one “typical” trajectory in a system, which can also be integrated with other available simulation tools.

Mems Lab Simulation Tool, Oluwatosin D. Adeosun, Sambit Palit, Ankit Jain, Muhammad A. Alam

The Summer Undergraduate Research Fellowship (SURF) Symposium

MEMS actuators have multiple design applications. Understanding their behavior as well as the ability to predict their actuation characteristics and voltage response is important when designing these actuators. In order to know these devices will behave, designers have to solve multiple analytical equations and experiments that can be very time consuming. Over the course of the summer a tool was created on nanoHUB that will allow users to enter information about a MEMS actuator and provide the voltage response of the actuator. To create the tool, scaling equations were first provided for various geometry configurations and the equations were next …