Solar Soiling Mitigation, Claire Desmith

Electrical Engineering

This senior project aims to mitigate performance losses that occur in Photovoltaic (PV) systems due to soiling of the panels. Soiling is the natural occurrence of debris accumulation on panels, depending on local climate conditions. Soiling loss refers to efficiency lost due to dirt and dust accumulation on the panels. The debris reduces system output by shading on a smaller scale. In addition to uniform soiling, corner soiling is observed in framed modules as debris collects in the corners of the modules. While solutions currently exist to clean modules to mitigate soiling losses, these solutions are often expensive and time …

Economics Of Grid-Tied Solar Photovoltaic Systems Coupled To Heat Pumps: The Case Of Northern Climates Of The U.S. And Canada, Joshua M. Pearce, Nelson Sommerfeldt

Michigan Tech Publications, Part 1

Solar photovoltaic (PV) technology is now a profitable method to decarbonize the grid, but if catastrophic climate change is to be avoided, emissions from transportation and heating must also decarbonize. One approach to renewable heating is leveraging improvements in PV with heat pumps (HPs). To determine the potential for PV+HP systems in northern areas of North America, this study performs numerical simulations and economic analysis using the same loads and climate, but with local electricity and natural gas rates for Sault Ste. Marie, in both Canada and U.S. Ground-mounted, fixed-tilt, grid-tied PV systems are sized to match 100% of electric …

Study Of Renewable Energy Penetration On A Benchmark Generation And Transmission System, Oluwaseun M. Akeyo, Aron Patrick, Dan M. Ionel

Electrical and Computer Engineering Faculty Publications

Significant changes in conventional generator operation and transmission system planning will be required to accommodate increasing solar photovoltaic (PV) penetration. There is a limit to the maximum amount of solar that can be connected in a service area without the need for significant upgrades to the existing generation and transmission infrastructure. This study proposes a framework for analyzing the impact of increasing solar penetration on generation and transmission networks while considering the responses of conventional generators to changes in solar PV output power. Contrary to traditional approaches in which it is assumed that generation can always match demand, this framework …

Water Conservation Potential Of Self-Funded Foam-Based Flexible Surface-Mounted Floatovoltaics, Kaomi Soulemane Hayibo, Pierce Mayville, Ravneet Kaur Kailey

Michigan Tech Publications, Part 1

A potential solution to the coupled water–energy–food challenges in land use is the concept of floating photovoltaics or floatovoltaics (FPV). In this study, a new approach to FPV is investigated using a flexible crystalline silicon-based photovoltaic (PV) module backed with foam, which is less expensive than conventional pontoon-based FPV. This novel form of FPV is tested experimentally for operating temperature and performance and is analyzed for water-savings using an evaporation calculation adapted from the Penman–Monteith model. The results show that the foam-backed FPV had a lower operating temperature than conventional pontoon-based FPV, and thus a 3.5% higher energy output per …

The Effect Of High Efficiency Building Technologies And Pv Generation On The Energy Profiles For Typical Us Residences, Evan S. Jones, Rosemary E. Alden, Huangjie Gong, Andrew G. Frye, Donald G. Colliver, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

The penetrations of high efficiency technologies and photovoltaic (PV) generation are increasing in the residential sector. Technologies such as improved insulation and efficient HVAC systems significantly affect the energy profile of a house. This effect varies due to climate characteristics, i.e. temperature, solar radiation, relative humidity, and wind speeds. The effect of other technologies, such as efficient water heaters, lighting, or kitchen appliances, is mainly governed by human behavior, which may be represented by a schedule. This paper studies the performance of both climate-influenced and scheduled household devices among different levels of efficiency through combined computational and experimental methods. Three …

Techno-Economic Comparative Analysis Of Renewable Energy Systems: Case Study In Zimbabwe, Loiy Al-Ghussain, Remember Samu, Onur Taylan, Murat Fahrioglu

Mechanical Engineering Graduate Research

Fluctuations in fossil fuel prices significantly affect the economies of countries, especially oil-importing countries, hence these countries are thoroughly investigating the increase in the utilization of renewable energy resources as it is abundant and locally available in all the countries despite challenges. Renewable energy systems (RES) such as solar and wind systems offer suitable alternatives for fossil fuels and could ensure the energy security of countries in a feasible way. Zimbabwe is one of the African countries that import a significant portion of its energy needs which endanger the energy security of the country. Several studies in the literature discussed …

The Hybridization Of A Graphene And Silicon Carbide Schottky Optoelectronic Device By The Incorporation Of A Lead Sulfide Quantum Dot Film, Joshua Letton

Theses and Dissertations

The work that follows examines the impact of lead sulfide quantum dots on a native epitaxial graphene (EG) SiC Schottky device, resulting in a hybrid optoelectronic device which presents a possible avenue towards a novel hybrid carbide-based Schottky solar cell. The active (n-type SiC) and contact (graphene) layers for the Schottky junction of the device were grown epitaxially using a novel technique incorporating tetrafluorosilane (TFS) as a precursor gas. The bare EG/SiC device was characterized based on its I-V behavior in dark and under illumination for both forward and reverse bias conditions. The initial characterization demonstrated the expected Schottky diode …

Long-Term Durability Of Solar Photovoltaic Modules, Chibuisi Chinasaokwu Okorieimoh, Brian Norton

Conference papers

Solar photovoltaic (PV) panels experience long-term performance degradation resulting in lower like-per-like efficiencies and performance ratios when compared with their initial performance. Manufacturers of solar photovoltaic modules usually guarantee the life span for more than 20 years. It is therefore necessary to track and mitigate degradation of PV modules over this period to satisfy such guarantees and beyond this period to identify maintenance and repair requirements. Degradation of solar PV modules makes them less efficient, less reliable and, ultimately, inoperative. This paper reviews relevant literature to discuss:

• Causes of efficiency reductions in photovoltaic cells

• Ways to achieve long-term durability of …

Comprehensive Optimization Models For Voltage Regulation In Pv-Rich Multi-Phase Distribution Systems, Ibrahim Alsaleh

USF Tampa Graduate Theses and Dissertations

The distribution systems are increasingly challenged by the continued prevalence of distributed energy resources (DERs), signaling the need for new computational tools to systemize their involvement, coordinate their operation with existing control devices, and mitigate undesired actuation of expensive equipment. Co-optimized operation of the various control devices becomes possible with the advancement in the power system optimization algorithms and the increased deployment of advanced metering infrastructure, offering system awareness and two-way communication. The steady-state alternating-current optimal power flow (ACOPF) problem, being the most descriptive form of OPF, lies at the root of power system optimization, aiming to minimize an operating …

Energy And Economic Losses Due To Soiling On Utility Scale Pv Systems To Guide Timing Of Cost Effective Cleaning, Sophia Mcmillin Stockburger, Vicente Jesus Rios

Electrical Engineering

The purpose of this senior project is to develop and recommend a cleaning schedule for Goldtree Solar Farm that is both economically beneficial and an efficient use of cleaning for the client. Solar farms can have various factors that influence the cleaning schedule such as weather behavior, time of the year, soiling, and other factors. Through this senior project, the goal is to assess these factors effect on the solar farm to produce a cleaning schedule that will maximize energy production, maximize profits, and prevent insignificant cleaning

This analysis is motivated by defining and promoting the benefits of regular maintenance …

Neca Ghana Project, Michael T. Klee

Construction Management

Cal Poly’s motto is, “Learn by Doing" and for Cal Poly’s NECA Chapter, this isn’t simply a motto, but a directive for proactive change. For my senior project I will be leading the Cal Poly NECA chapter in the design, pre- fabrication and construction of a 5-7kw solar array, community center, ice production room and technology room in the remote fishing village of Agbokpa, Ghana. The solar array will power multiple industrial DC freezers, high efficiency LED lighting and charging stations while additionally powering water filtration and irrigation systems. Like many other fishing villages around the world, Agbokpa has no …

Water Conservation Potential Of Self-Funded Foam-Based Flexible Surface-Mounted Floatovoltaics, Koami Soulemane Hayibo, Pierce Mayville, Ravneet Kaur Kailey, Joshua M. Pearce

Electrical and Computer Engineering Publications

A potential solution to the coupled water–energy–food challenges in land use is the concept of floating photovoltaics or floatovoltaics (FPV). In this study, a new approach to FPV is investigated using a flexible crystalline silicon-based photovoltaic (PV) module backed with foam, which is less expensive than conventional pontoon-based FPV. This novel form of FPV is tested experimentally for operating temperature and performance and is analyzed for water-savings using an evaporation calculation adapted from the Penman–Monteith model. The results show that the foam-backed FPV had a lower operating temperature than conventional pontoon-based FPV, and thus a 3.5% higher energy output per …

Triple-Junction Solar Cells : In Parallel., Levi C Mays

Electronic Theses and Dissertations

This paper looks into the current inefficiency of solar cells and attempts a few alternative solar cell structures in order to provide a more effective source of renewable energy. Currently, multi-junction solar cells are being developed to capture the sun’s light more efficiently. One of the ideas in this paper is to add a window to see if the addition of such a layer into a junction will increase the voltage while maintaining nearly the same current output. Central to this paper is the rearranging of the conducting layers of the multi-junction cell so that the junctions can be connected …

Pv Hybrid Inverter And Bess, Jacob Sussex, William Dresser, Owen Mckenzie, Jonathan Wharton, Derek Seaman

Electrical Engineering

The storage of energy from renewable sources such as photovoltaic based systems is a growing market, with 36 MWh of storage installed in Q1 of 2018. A report from EnergySage earlier this year states that in 2017, 74% of residential solar owners were also interested in energy storage systems. Mainstream systems like Tesla’s Powerwall are competing with other lithium-ion based storage systems from a wide number of providers on the market today. Short term and long term data collection on a system like this could be useful in designing future systems which perform better than the current market offerings. This …

Design And Analysis Of A Non-Isolated High Gain Step-Up Cuk Converter, Yasser Almalaq

Electronic Theses and Dissertations

Renewable energy sources, such as solar energy, are desired for both economic and ecological issues. These renewable energy sources are plentiful in nature and have a terrific capability for power generation. The only drawback of solar energy, which is one of the best forms of energy sources, is that the output has a low voltage and needs to be stepped up in order to be inserted into the DC grid or an inverter for AC applications. To overcome this drawback, a high gain DC-DC power converter is required in this kind of system. These power converters are needed for a …

The Effect Of Snowfall And Icing On The Sustainability Of The Power Output Of A Grid-Connected Photovoltaic System In Konya, Turkey, Mehmet Ali̇ Anadol, Erman Erhan

Turkish Journal of Electrical Engineering and Computer Sciences

When the module surface is covered with various factors such as snow and icing which prevent the solar irradiance from reaching the photovoltaic cells, the power production of the system and its performance decrease. The purpose of this study is to determine the energy production losses of a grid-connected photovoltaic plant due to snowfall and icing. The effect of snowfall and icing has been examined on a photovoltaic system consisting of a hybrid inverter with two separate maximum power point tracking inputs and 36 monocrystalline modules, which are mounted on the supporting system horizontally in the south direction and at …

Open Source Low-Cost Power Monitoring System, Shane W. Oberloier, Joshua M. Pearce

Department of Materials Science and Engineering Publications

This study presents an entirely open-source, low-cost power monitoring system capable of many types of measurements including both loads and supplies such as solar photovoltaic systems. In addition, the system can be fabricated using only open source software and hardware. The design revolves around the Digital Universal Energy Logger (DUEL) Node, which is responsible for reading and properly scaling the voltage and current of a particular load, and then serializing it via an on-board ATTiny85 chip. The configuration of the DUEL node allows for custom sensitivity ranges, and can handle up to 50 A and 300 V. Up to 127 …

The Analysis And Study Of Power System Designs For Same Polytechnic College In Tanzania, Kevin Lum Hua

Master's Theses

The Mbesese Initiative for Sustainable Development (MISD) is a group aiming to help eliminate extreme poverty in Africa by creating educational opportunity. One project that the group is currently doing is to build Same Polytechnic College (SPC) in Tanzania. As part of the project, this thesis aims to study and analyze the electrical power system and distribution for the college. Based on the projected load profile of the college and high potential for solar generation in Tanzania, several different power systems utilizing local utility AC electricity and/or photovoltaic (PV) DC electricity are explored and simulated for their feasibility and performance. …

Self-Sufficiency Of 3-D Printers: Utilizing Stand-Alone Solar Photovoltaic Power Systems, Khalid Yousuf Khan, Lucia Gauchia, Joshua M. Pearce

Department of Materials Science and Engineering Publications

A self-replicating rapid prototyper (RepRap) is a type of 3-D printer capable of printing many of its own components in addition to a wide assortment of products from high-value scientific or medical tools to household products and toys. There is some evidence that these printers could provide low-cost distributed manufacturing in underprivileged rural areas. For the most isolated communities without access to the electric grid, a low-cost alternative energy is needed. Solar energy can be harvested through a stand-alone photovoltaic (PV) power system specifically designed to match the needs of the RepRap. The voltage and current requirement for the printer …

Design, Fabrication, And Characterization Of Novel Optoelectronic Devices For Near-Infrared Detection, Ahmad Nusir

Graduate Theses and Dissertations

Investigating semiconductor materials and devices at the nanoscale has become crucial in order to maintain the exponential development in today’s technology. There is a critical need for making devices lower in power consumption and smaller in size. Nanoscale semiconductor materials provide a powerful platform for optoelectronic device engineers. They own interesting properties which include enhanced photoconductivity and size-tunable interband transitions.

In this research, different types of nanostructures were investigated for optoelectronic devices: nanocrystals, nanowires, and thin-films. First, lead selenide nanocrystals with narrow bandgap were synthesized, size-tailored, and functionalized with molecular ligands for the application of uncooled near-infrared photodetectors. The devices …

Developing A 1-Megawatt Photovoltaic Power Plant For Liberty University, Andrew Knudsen

Senior Honors Theses

A photovoltaic power plant with a generation capacity of 1-megawatt is designed for Liberty University. Liberty University’s location and size are stated to provide context for the design. Design choices are presented, first with general information that is applicable to any photovoltaic plant design, then with significant factors that impact this design. Specific models of solar panels and inverters are selected after the necessary classifications are determined. The final design has 2,880 solar panels with a fixed angle 30⁰ above the horizon, has two central inverters, and takes up 2.57 acres. Future research is suggested for finances as well as …

Supercapacitor Utilization For Power Smoothening And Stability Improvement Of Ahybrid Energy System In A Weak Grid Environment, Rahul Sharma, Sathans Suhag

Turkish Journal of Electrical Engineering and Computer Sciences

In this paper, a novel control scheme based on the application of a supercapacitor (SC) is proposed for power smoothening and stability improvement of a hybrid energy system (HES) in weak grid conditions. The basic property of fast charging/discharging of the SC is utilized to design the proposed control. In weak grid conditions, the control structure is proposed for power smoothening and DC link voltage regulation with the help of the SC. Moreover, the stability is increased, ripples in voltage are reduced, there is fast dynamic response, and oscillations are damped out under different conditions. In conventional control, voltage controller …

Advanced Topologies Of High-Voltage-Gain Dc-Dc Boost Converters For Renewable Energy Applications, Ahmad Alzahrani

Doctoral Dissertations

This dissertation proposes several advanced power electronic converters that are suitable for integrating low-voltage dc input sources, such as photovoltaic (PV) solar panels, to a high voltage dc bus in a 200 - 960 V dc distribution system. The proposed converters operate in the continuous conduction mode (CCM) and offer desirable features such as low-voltage stresses on components, continuous input currents, and the ability to integrate several independent dc input sources. First, a family of scalable interleaved boost converters with voltage multiplier cells (VMC) is introduced. Several possible combinations of Dickson and Cockcroft-Walton VMCs are demonstrated and compared in terms …

Photovoltaic Inverter Control To Sustain High Quality Of Service, Yan Chen

Theses and Dissertations

The increasing penetration of distributed solar photovoltaic (PV) generation presents both challenges and opportunities for distribution systems. The intermittent nature of solar irradiance may lead to power quality degradation. At the same time, PV inverters –if properly designed and operated– can be used to improve power quality. The goal of this dissertation is to develop power flow optimization methods for power distribution networks with high penetration of PV generation. The approaches proposed in this dissertation have been tested using the modified version of the IEEE 34-node distribution system and the IEEE 123-node distribution system, as well as the validated model …

Design Of Post-Consumer Modification Of Standard Solar Modules To Form Large-Area Building-Integrated Photovoltaic Roof Slates, Joshua M. Pearce, Jay Meldrum, Nolan Osborne

Department of Materials Science and Engineering Publications

Building-integrated photovoltaic (BIPV) systems have improved aesthetics but generally cost far more than conventional PV systems because of small manufacturing scale. Thus, in the short and medium term, there is a need for a BIPV mounting system that utilizes conventional modules. Such a design is provided here with a novel modification of conventional photovoltaic (PV) modules to allow them to act as BIPV roofing slates. The open-source designs for the mechanical components necessary to provide the post-consumer conversion for a conventional PV module are provided, and prototypes are fabricated and installed on a mock roof system along with control modules …

General Design Procedures For Airport-Based Solar Photovoltaic Systems, Anurag Anurag, Jiemin Zhang, Jephias Gwamuri, Joshua M. Pearce

Department of Materials Science and Engineering Publications

A source of large surface areas for solar photovoltaic (PV) farms that has been largely overlooked in the 13,000 United States of America (U.S.) airports. This paper hopes to enable PV deployments in most airports by providing an approach to overcome the three primary challenges identified by the Federal Aviation Administration (FAA): (1) reflectivity and glare; (2) radar interference; and (3) physical penetration of airspace. First, these challenges and precautions that must be adhered to for safe PV projects deployment at airports are reviewed and summarized. Since one of the core concerns for PV and airport symbiosis is solar panel …

Fabricating Ordered 2-D Nano-Structured Arrays Using Nanosphere Lithography, Chenlong Zhang, Sandra Cvetanovic, Joshua M. Pearce

Department of Materials Science and Engineering Publications

Recent advances in the use of plasmonic metamaterials to improve absorption of light in thin-film solar photovoltaic devices has created a demand for a scalable method of patterning large areas with metal nanostructures deposited in an ordered array. This article describes two methods of fabricating ordered 2D nanosphere colloidal films: spin coating and interface coating. The two methods are compared and parameter optimization discussed. The study reveals that:

• For smaller nanosphere sizes, spin coating is more favorable, while for larger nanospheres, the angled interface coating provides more coverage and uniformity.

• A surfactant-free approach for interface coating is developed …

Design & Evaluation Of A Hybrid Switched Capacitor Circuit With Wide-Bandgap Devices For Dc Grid Applications, Joshua L. Stewart

Electrical and Computer Engineering ETDs

ABSTRACT

As technologies advance, the rate at which renewable power sources, such as solar photovoltaic (PV) and wind, are being added to the power grid is increasing. Typically, PV power plants require large inverters for direct current to alternating current (DC-AC) power conversion, as well as large transformers to step up voltages to the grid voltage. Offshore wind farms and large PV power plants in remote locations often aggregate power on a DC bus in order to improve efficiency and reduce the cost of power conversion hardware within the energy complex. However, the power must still be converted to AC …

Modeling And Charging Control Of A Lithium Ion Battery System For Solar Panels, Garrett David Heinen

Master's Theses

The advancement in solar panel and battery technology makes them useful for energy supply and storage. This thesis involves the modeling and charging control of a lithium ion battery system for solar panels. The proposed model is based on the parameters and characteristics of a realistic battery and solar panel system; and the hybrid control approach combines the advantages of the adaptive incremental conductance method and the perturb and observe method to track the maximum power point of the solar panel for charging the battery unit. Computer simulation results demonstrate that this proposed approach offers a faster convergence rate than …

Probabilistics Risk Assessment Of Power Quality Variations And Events Under Temporal And Spatial Characteristic Of Increased Pv Integration In Low Voltage Distribution Networks, Shivananda Pukhrem, Malabika Basu, Michael Conlon

Articles

Integration of PVDG reduces the voltage unbalance as compared with no or low PVDG penetration. There is a higher probability of observing deep sag at the site as PVDG integration increases. This probabilistic approach can be used as a tool to assess the likely impacts due to PVDG integration against the worst-case scenarios.