Electrical and Computer Engineering Commons^™

Ultra-Low Voltage Digital Circuits And Extreme Temperature Electronics Design, Aaron J. Arthurs

Graduate Theses and Dissertations

Certain applications require digital electronics to operate under extreme conditions e.g., large swings in ambient temperature, very low supply voltage, high radiation. Such applications include sensor networks, wearable electronics, unmanned aerial vehicles, spacecraft, and energyharvesting systems. This dissertation splits into two projects that study digital electronics supplied by ultra-low voltages and build an electronic system for extreme temperatures. The first project introduces techniques that improve circuit reliability at deep subthreshold voltages as well as determine the minimum required supply voltage. These techniques address digital electronic design at several levels: the physical process, gate design, and system architecture. This dissertation analyzes …

Fabrication And Characterization Of Thinner Solid-State Nanopores, Denis Forbi Tita

Graduate Theses and Dissertations

Solid State nanopores that are fabricated by the ion beam sculpting process and electron beam drilling have shown great promise as a sensing device for DNA and protein molecules. Even though biological pores such as the alpha-Haemolysin have been in use for quite some time, the use of solid state Nanopores in single biomolecule detection has been on the rise since the mid 1990s. Solid State nanopores have an advantage over biological pores in that they are more robust, stable, and can be sculpted to any desired size for use in translocation experiments. One of the major challenges in Nanopore …

Delay Insensitive Ternary Logic Utilizing Cmos And Cntfet, Ravi Sankar Parameswaran Nair

Graduate Theses and Dissertations

As digital circuit design continues to evolve due to progress of semiconductor processes well into the sub 100nm range, clocked architectures face limitations in a number of cases where clockless asynchronous architectures require substantially less power, generate less noise, and produce less electromagnetic interference (EMI). This dissertation develops the Delay Insensitive Ternary Logic (DITL) asynchronous design paradigm that combines the designs aspects of similar Dual-Rail asynchronous paradigms and Boolean logic to create a single wire per bit, three voltage signaling and logic scheme.

DITL is designed at the transistor level using multi-threshold CMOS and carbon nanotube (CNT) FETs to develop …

A Silicon Carbide Linear Voltage Regulator For High Temperature Applications, Javier Antonio Valle Mayorga

Graduate Theses and Dissertations

Current market demands have pushed the capabilities of silicon to the edge. High temperature and high power applications require a semiconductor device to operate reliably in very harsh environments. This situation has awakened interests in other types of semiconductors, usually with a higher bandgap than silicon's, as the next venue for the fabrication of integrated circuits (IC) and power devices. Silicon Carbide (SiC) has so far proven to be one of the best options in the power devices field.

This dissertation presents the first attempt to fabricate a SiC linear voltage regulator. This circuit would provide a power management option …

Molecular Dynamics Study Of Diffusion Of O2 Penetrates In Uncrosslinked Polydimethysiloxane (Pdms), Crosslinked Pdms, And Pdms-Based Nanocomposites, Varun Ullal

Graduate Theses and Dissertations

Molecular dynamics simulations are used to study diffusion of O₂ molecules in pure polydimethysiloxane (PDMS), crosslinked PDMS, and PDMS-based nanocomposites. The PDMS chains and penetrates are modeled using a hybrid interatomic potential which treats the Si-O atoms along the chain backbone explicitly while coarse-graining the methyl side groups and penetrates. By tracking the diffusion of penetrates in the system and subsequently computing their mean-squared displacement, diffusion coefficients are obtained. In pure PDMS models of varying molecular weight, diffusivity of the O₂2 penetrates is found to have an inverse relationship with chain length. Simulation models with longer chains …

Plasma-Assisted Molecular Beam Epitaxial Growth Of Indium Nitride For Future Device Fabrication, Steven Paul Minor

Graduate Theses and Dissertations

The need for energy conservation has heightened the search for new materials that can reduce energy consumption or produce energy by the means of photovoltaic cells. III-nitride alloys show promise for these applications due to their generally good transport properties and ability to withstand high power applications. Along with these, this family of semiconductor alloys has a direct bandgap energy range (0.7-6.2 eV) which spans the entire visible spectrum and encompasses a large portion of the available solar spectrum. Of the three root III-nitride semiconductors, AlN, GaN, and InN, InN has only recently become attainable epitaxially with qualities good enough …

Experimental Study Of Novel Materials And Module For Cryogenic (4k) Superconducting Multi-Chip Modules, Ranjith John

Graduate Theses and Dissertations

The objectives of this proposal are to understand the science and technology of interfaces in the packaging of superconducting electronic (SCE) multichip modules (MCMs) at 4 K. The thermal management issue of the current SCE-MCMs was examined and the package assembly was optimized. A novel thermally conducting and electrically insulating nano-engineered polymer was developed for the thermal management of SCE-MCMs for 4 K cryogenic packaging. Finally, the nano-engineered polymer was integrated as underfill in a SCE-MCM and the thermal and electrical performance of SCE-MCM was demonstrated at 4 K.

Niobium based superconducting electronics (SCE) are the fastest known digital logic …

Silicon Germanium Sram And Rom Designs For Wide Temperature Range Space Applications, Matthew Barlow

Graduate Theses and Dissertations

This thesis presents a design flow from specifications and feature requirements to embeddable blocks of SRAM and ROM designs from 64 bytes to 1 kilobyte that are suitable for lunar environments. The design uses the IBM SiGe 5AM BiCMOS 0.5 micron process for a synchronous memory system capable of operating at a clock frequency of 25 MHz. Radiation mitigation techniques are discussed and implemented to harden the design against total ionizing dose (TID), single-event upset (SEU), and single-event latch-up (SEL). The memory arrays are also designed to operate over the wide temperature range of -180 °C to 125 °C. Design, …

Design Of A High Dynamic Range Cmos Variable Gain Amplifier For Wireless Sensor Networks, Yue Yu

Graduate Theses and Dissertations

This thesis presents the design, simulation, layout and testing results for a dB-linear, high dynamic gain range CMOS variable gain amplifier (VGA). The design adopts a new approximated exponential equation called the pseudo exponential equation to implement the dB-linear function. The proposed VGA is designed to have an extremely wide gain variation, small chip area, low supply voltage, and controllable dynamic gain range. The gain variation of the 3-stage VGA is implemented by a voltage to current converter. It controls the bias currents of each VGA cell, so that the output gain of each cell can be controlled. In order …

Characterization And Modeling Of 4h-Sic Low Voltage Mosfets And Power Mosfets, Mihir Mudholkar

Graduate Theses and Dissertations

The integration of low voltage and high voltage circuits on SiC has profound applications. SiC power devices have proved their superiority in terms of high temperature operation, faster switching frequencies and larger power densities when compared with Si power devices. The control of SiC power devices however, lies in the hands of low voltage circuits built on Si. Thus, there exists a separation in the overall system between the low voltage and high voltage side, which increases system cost, weight and reduces efficiency. With the advancement in low voltage SiC processing technology, low voltage control circuits can be made on …

Fabrication Of Vertical Silicon Nanowires Through Metal Assisted Deposition, Matthew Garett Young

Graduate Theses and Dissertations

Controlled and ordered growth of Si nanowires through a low temperature fabrication method compatible with CMOS processing lines is a highly desirable replacement to future electronic fabrication technologies as well as a candidate for a low cost route to inexpensive photovoltaics. This stems from the fact that traditional CMOS based electronics are hitting physical barriers that are slowing the Moore's Law trend as well as the demand for an inexpensive solar cell technology that can obtain grid parity. A fractional factorial growth study is presented that compares the growth of Au and Al catalyzed Si nanowires at temperatures ranging from …

Design Of An Rf Cmos Power Amplifier For Wireless Sensor Networks, Hua Pan

Graduate Theses and Dissertations

The Power Amplifier (PA) is the last Radio Frequency (RF) building block in a transmitter, directly driving an antenna. The low power RF input signal of the PA is amplified to a significant power RF output signal by converting DC power into RF power. Since the PA consumes a majority of the power, efficiency plays one of the most important roles in a PA design. Designing an efficient, fully integrated RF PA that can operate at low supply voltage (1.2V), low power, and low RF frequency (433MHz) is a major challenge. The class E Power Amplifier, which is one type …

Implementation Of Orthogonal Frequency Division Multiplexing With Fpga, Qi Hao Yang

Graduate Theses and Dissertations

In recent years, there have been dramatic shifts in cellular and telecommunication industries. As smartphones are dominating on the cellphone market, more and more people use these mobile devices to access internet either through third generation network or IEEE802.11 wireless local area network. Orthogonal frequency division multiplexing (OFDM) has been widely used in IEEE802.11 wireless local area network and fourth generation network. This paper will focus on the design and implementation of an Orthogonal Frequency Division Multiplexing system on field-programmable gate array (FPGA). The major components of an OFDM system include a modulator, an N-input inverse Fast Fourier Transform (IFFT), …

Use Of Ultra High Vacuum Plasma Enhanced Chemical Vapor Deposition For Graphene Fabrication, Shannen Adcock

Graduate Theses and Dissertations

Graphene, what some are terming the "new silicon", has the possibility of revolutionizing technology through nanoscale design processes. Fabrication of graphene for device processing is limited largely by the temperatures used in conventional deposition. High temperatures are detrimental to device design where many different materials may be present. For this reason, graphene synthesis at low temperatures using plasma-enhanced chemical vapor deposition is the subject of much research. In this thesis, a tool for ultra-high vacuum plasma-enhanced chemical vapor deposition (UHV-PECVD) and accompanying subsystems, such as control systems and alarms, are designed and implemented to be used in future graphene growths. …

High Frequency Characterization Of Carbon Nanotube Networks For Device Applications, Emmanuel Decrossas

Graduate Theses and Dissertations

This work includes the microwave characterization of carbon nanotubes (CNTs) to design new CNTs-based high frequency components. A novel developed method to extract the electrical properties over a broad microwave frequency band from 10 MHz to 50 GHz of carbon nanotubes (CNTs) in a powder form is performed. The measured scattering parameters (S-parameters) with a performance network analyzer are compared to the simulated one obtained from an in-house computed mode matching technique (MMT). An optimized first order gradient method iteratively changes the unknown complex permittivity parameters to map the simulated S-parameters with the measured one until convergence criteria are satisfied. …

Ultra-Low Power And Radiation Hardened Asynchronous Circuit Design, Liang Zhou

Graduate Theses and Dissertations

This dissertation proposes an ultra-low power design methodology called bit-wise MTNCL for bit-wise pipelined asynchronous circuits, which combines multi-threshold CMOS (MTCMOS) with bit-wise pipelined NULL Convention Logic (NCL) systems. It provides the leakage power advantages of an all high-Vt implementation with a reasonable speed penalty compared to the all low-Vt implementation, and has negligible area overhead. It was enhanced to handle indeterminate standby states. The original MTNCL concept was enhanced significantly by sleeping Registers and Completion Logic as well as Combinational circuits to reduce area, leakage power, and energy per operation.

This dissertation also develops an architecture that allows NCL …

Fabrication Of Composite Nanomaterials For Thin Film Amorphous Silicon Solar Cells, Benjamin Seth Newton

Graduate Theses and Dissertations

A material with the precise combination of amorphous silicon and polycrystalline silicon would be able to take advantage of the high absorption capabilities of amorphous silicon and the electron transport capabilities of polycrystalline silicon. Polycrystalline nanostructures in the form of wires can also take advantage of other properties of light absorption, trapping and scattering inherent in nanowire structures. These properties of high absorption and electron transport in one device would lead to advances in the search for highly efficient low cost solar cells and sensors. In this work a thin film material composed of an array of polycrystalline silicon nanostructures …

Subthreshold 3 Phase Mixers, Jesus Angel Torres

Theses and Dissertations - UTB/UTPA

This thesis will discuss subthreshold FET mixers with a focus on conversion loss derivations. To begin understanding the mixers, a look into the FET model is first taken in Chapter II. Then in Chapter III, a single FET device mixer is studied and its conversion loss is found from its small-signal model. The chapter will then include a two FET device mixer and a four device FET mixer. Finally a new type of mixer will be discussed in Chapter IV. The new type of mixer is a 3 phase mixer with the phase angles being 0°, 120°, and 240°. The …

A Study Of A Novel Modular Variable Geometry Frame Arranged As A Robotic Surface, Christopher James Salisbury

UNLV Theses, Dissertations, Professional Papers, and Capstones

The novel concept of a "variable geometry frame" is introduced and explored through a three-dimensional robotic surface which is devised and implemented using triangular modules. The link design is optimized using surplus motor dimensions as firm constraints, and round numbers for further arbitrary constraints. Each module is connected by a passive six-bar mechanism that mimics the constraints of a spherical joint at each triangle intersection. A three dimensional inkjet printer is used to create a six-module prototype designed around surplus stepper motors powered by an old computer power supply as a proof-of-concept example.

The finite element method is applied to …

Sensing And Transmission Strategies In Wireless Cognitive Radio Systems, Babak Abbasi Bastami

UNLV Theses, Dissertations, Professional Papers, and Capstones

The main challenge in any cognitive radio system is to maximize secondary users throughput while limiting interference imposed on licensed users. In this regard, finding the optimal sensing and transmission timing strategies and accurate sensing techniques are of great importance in a cognitive radio network.

In this thesis, we study a sensing-transmission scheme for secondary user in a cognitive radio system where the secondary user senses every primary channel independently and transmits a signal for a fixed duration if it finds the channel empty and stays idle for another fixed duration if it senses the channel busy. We obtain optimal …

Energy-Based Analysis Of Utility Scale Hybrid Power Systems, Kwame Agyenim-Boateng

UNLV Theses, Dissertations, Professional Papers, and Capstones

The promise of large-scale use of renewables such as wind and solar for supplying electrical power is tempered by the sources' transient behavior and the impact this would have on the operation of the grid. Among the methods cited for addressing some of those concerns are exploring the complementary nature of solar and wind power generation, and through the use of supplemental energy storage. While the technology for the latter has not been proven to be economical on a large scale at the present time, some assessments of what magnitude is required can be made. An energy-based analysis of utility …

Design Of An 866 Mhz On-Chip Frequency Synthesizer, Phaniraj Joshi

Graduate Theses and Dissertations

There is a strong need for stable frequency references with large tuning ranges in today's communication systems. While the crystal oscillators assure good frequency stability, it is not possible to achieve a large frequency range by tuning the passive components attached to them. Frequency synthesizers are usually used for this purpose because of their ability to produce a variety of output frequencies. The Phase Locked Loop (PLL) based frequency synthesizer is the most preferred of all types of synthesizers available because of its additional features like programmability, low noise and low cost as well as high accuracy and stability. The …

Fabrication Of Horizontal Silicon Nanowires Using A Thin Aluminum Film As A Catalyst, Khaja Hafeezuddin Mohammed

Graduate Theses and Dissertations

Silicon nanowires have been the topic of research in recent years for their significant attention from the electronics industry to grow even smaller electronic devices. The semiconductor industry is built on silicon. Silicon nanowires can be the building blocks for future nanoelectronic devices. Various techniques have also been reported in fabricating the silicon nanowires. But most of the techniques reported, grow vertical silicon nanowires. In the semiconductor industry, integrated circuits are designed and fabricated in a horizontal architecture i.e. the device layout is flat compared to the substrate. When vertical silicon nanowires are introduced in the semiconductor industry, a whole …

Investigation Of A Floating Load Buck Dc-Dc Switching Converter, Hong Tan

Graduate Theses and Dissertations

A floating load buck DC-DC switching converter was analyzed, simulated, designed and prototyped. The floating load buck converter is first compared to the conventional buck converter. It was found that both the floating load buck converter and conventional buck converter exhibit similar conversion characteristics despite the differences in the placement of their output inductors. A floating load buck converter was designed to be used as a high-voltage off-line light-emitting diodes (LEDs) driver using a Texas Instruments' TPS92001 controller. Finally, the characteristics of this floating load buck converter LED driver were experimentally examined.

Design Of A Low Noise Amplifier For Wireless Sensor Networks, Ting Liu

Graduate Theses and Dissertations

CMOS technology becomes important in Radio Frequency (RF) communication systems which include both a receiver and a transmitter. In a high performance radio receiver, the Low Noise Amplifier (LNA) is the first circuit, and its noise performance dominates the entire receiver. Depending upon the system in which they are used, LNAs can be designed according to various topologies and structures. The LNA needs to have matched input impedance, and at the same time it should amplify the small amplitude input signal without adding too much noise and still have the minimal power consumption. It also needs a good interface with …

Development Of Spray Cooling For High Heat Flux Electronics, Jeremy Scott Junghans

Graduate Theses and Dissertations

The thermal demands of modern day electronic systems require innovative thermal solutions. Spray cooling has proven to be able to cool heat fluxes orders of magnitude higher than traditional cooling methodologies. This work includes a comparison of spray cooling to standard thermal management methodologies. Key system parameters and considerations are discussed. The properties of available packaging materials and their effect on the reliability of a spray cooled system are presented. Parameters such as fluid temperature, droplet size, fluid velocity and flow rate all directly impact performance and are detailed in this work. Finally, results from of a wide range of …

Design And Implementation Of Metamaterial Based Strain Sensor Using Aperture Coupled Antenna, Michael Brandon Buscher

Graduate Theses and Dissertations

Strain sensors are used to convert the physical measured quantity of strain into an electrical signal suitable for processing by electronic equipment. Traditional strain sensors are comprised of a thin flexible film with a resistive pattern traced on the surface. As the sensor is deformed, the electrical resistance changes proportionally, giving a direct measure of the strain incurred. Metamaterials, particularly split ring resonators (SRR), lend themselves as a valuable tool for sensing applications due to their highly resonant nature and their very narrow bandwidth (high Q-factor). Due to very high field localization effects, they are extremely sensitive to both the …

Modeling And Characterization Of P-Type Silicon Carbide Gate Turn Off Thyristors, Osama Shihadeh Saadeh

Graduate Theses and Dissertations

Silicon carbide (SiC) power semiconductor devices have emerged in the past decade as the most promising technology for next generation power electronic applications ranging for electric vehicles to grid-connected power routing and conversion interfaces. Several devices have been developed, and even some have been released commercially, including diodes, MOSFETs, JFETs, thyristors, gate turn-off thyristors, and IGBTs. The model development, characterization and experimental validation of SiC p-type Gate Turn-off Thyristors (GTO) is presented in this work. The GTO device in this work is being used as part of a SiC-based solid-state fault current limiter under development at the University of Arkansas' …

Photodetectors And Photovoltaic Devices Based On Semiconductor Nanomaterials, Jiang Wu

Graduate Theses and Dissertations

Photodetectors based various nanostructures and plasmon enhanced solar cells are investigated in this dissertation. The motivation of the dissertation rise is driven by urgent need of both high efficiency photodetectors and solar cells.

First, quantum dot infrared photodetectors have been intensely investigated due to their promise in high performance photodetectors. However, the strain-driven growth of quantum dots has hindered the progress of quantum dot photodetectors. The presence of strain in the device presents complexity in designing as well as defects. Therefore, in this project, new designs of quantum dot photodetector structures are presented to improve the control over detection wavelength. …

Development Of Laboratory Based Smart Micro Grid To Be Used As An Educational Tool, Jose L. Sanchez

Theses and Dissertations - UTB/UTPA

The increasing trend of the energy industry to move towards a new smart power grid has pushed researchers to address the challenges that this represents. Universities all around the world are also under pressure to better prepare their students to meet the challenges that await them with this new technology and techniques. The work presented on this thesis was motivated by the current need of the electrical engineering curriculum to include new material into their current courses. A laboratory based smart micro grid was created by applying several concepts and techniques currently being adopted by the energy industry to make …