Electrical and Computer Engineering Commons^™

Preparation Of Mocvd-Grown Photocathodes Containing A Strained Gaas/Gaasp Superlattice, G. Blume, A. Masters, J. Grames, M. Stutzman, M. Grau, S. Marsillac

Physics Faculty Publications

In this work, we investigate heat cleaning options for high-polarization GaAs/GaAsP strained-superlattice (SSL) photocathodes with a distributed Bragg reflector (DBR) that were grown using metalorganic chemical vapor deposition (MOCVD). This was done using a microMott polarimeter at Jefferson Lab to optimize both quantum efficiency and polarization. The fabrication process for MOCVD-grown photocathodes does not allow for the inclusion of an arsenic cap, contrary to what is done when fabricating photocathodes using molecular-beam epitaxy (MBE). Without proper preparation, the performance of MOCVD-grown photocathodes can be limited due to surface contamination. Here, we varied both duration and temperature of the heat cleaning …

Old, Flat, And Slow: Interior Greenland Snow And Ice Dynamics Revealed With Gnss, Derek James Pickell

Dartmouth College Ph.D Dissertations

The interior dry snow zone region of the Greenland Ice Sheet can no longer be confidently considered a reliably melt-free region, yet our ability to investigate and quantify the dynamic nature of this landscape is hindered by its remoteness. To overcome this challenge, this work describes a novel, low-cost, low-power GNSS (positioning) instrument that enables simultaneous measurements of (1) ice accumulation/ablation changes and (2) 3D ice flow. Deployed in a dense array, these GNSS instruments achieve similar performance to scientific-grade, commercial options (cm- to mm- precision), yet operate at < 60% of the power and < 34% of the hardware cost. Over a three year campaign, we analyze spatial and temporal patterns of accumulation in this region, using a technique called GNSS interferometric reflectometry (GNSS-IR). Observations with this technique show low bias and high precision relative to a validation study (-2.1 ± 2.9 cm), while we also demonstrate for the first time how GNSS-IR can reveal cm- to m- scale surface roughness, a critical yet often neglected measurement due to longstanding observational challenges. Patterns of accumulation show a spatial dependence linked to surface slope (~+0.7 mm w.e. km^-1 westward away from the divide) while surface roughness has a temporal dependence likely driven by wintertime high winds. Next, we combine GNSS-IR surface heights with the geodetic position time series of the antenna to derive surface elevation changes, which are compared to coincident ICESat-2 laser altimetry elevations. Observations of the surface show a millimeter-level relative bias and cm-level precision (-0.9 ± 3.8 cm) compared with the satellite altimeter, demonstrating for the first time that this technique is a viable ground-truthing method, while ICESat-2 performance has continued to exceed mission performance requirements. Finally, we examine station positioning through time to show a sensitivity to dynamic ice thinning and firn densification, two parameters than cannot be finely observed with space-based methods in this region. Together, these results provide the first ground‑based, high‑resolution picture of interior ice‑sheet change—capturing accumulation, roughness, surface elevation, and strain in one unified dataset. Our approach dramatically lowers logistical barriers, opening the interior of Greenland (and other remote regions) to sustained, quantitative monitoring at unprecedented spatiotemporal resolution.

Selected Topics In Blockchain-Aided Iot Inference, Yiming Jiang

Doctoral Dissertations

"Blockchain has recently been considered in the Internet of Things (IoT) to secure data exchanges and storage across various engineering applications. This newly emerging blockchain-aided IoT (BIoT) network has been applied to a great deal of security-related applications. However, the BIoT still has the vulnerability that can be exploited by attackers, potentially impairing the performance of BIoT applications. Despite this, research addressing the vulnerability has been limited. This work presents four studies aimed at addressing critical gaps in current BIoT research.

The first study introduces a Time-Restricted Double-Spending Attack (TR-DSA) model for Proof-of-Work (PoW)-based blockchains, where the adversary only conducts …

New Topologies For High Voltage Gain Dc-Dc Power Electronic Converters – Theoretical Analysis And Experimental Validation, Saeed Habibi

Doctoral Dissertations

"This dissertation is focused on developing and analyzing new high voltage gain DC-DC power electronic converters. The proposed converters in this dissertation are suitable candidates for connecting low voltage sources such as photovoltaic (PV) panels or fuel cell (FC) stacks to a DC microgrid or DC link of an inverter. The proposed converters provide desired characteristics such as high voltage gain at a low or medium duty cycle values, low voltage stress on power semiconductors, and continuous input current. Initially, the research introduces three novel converter topologies: First, two quadratic converters based on the combination of a three-winding coupled inductor …

Power Supply Induced Jitter Analysis In High-Speed Drivers, Yifan Ding

Doctoral Dissertations

The Input/Output Buffer Information Specification (IBIS) model faces challenges in accurately simulating power-supply-induced jitter (PSIJ), particularly under nonlinear and time-varying power noise conditions with pre-driver stages. This work introduces advancements in IBIS model modification algorithms to enhance PSIJ simulation accuracy for high-speed drivers.

First, a correction coefficient-based approach was developed to adjust switching coefficients K_pu and K_pd using pre-driver DC jitter sensitivity, significantly improving model robustness under DC and AC power noise. However, its effectiveness diminished under large noise amplitudes due to coefficient shape dominance.

To address this, a simplified algorithm bypassed correction coefficient, directly correlating switching transitions with jitter …

Ecobuoys For Scalable Oceanography, Anuscheh Nawaz, Michael Steele, Ruth Branch, David Burnett, Kuotian Liao, Mallory Parker, Eleftheria Roumeli

Electrical and Computer Engineering Faculty Publications and Presentations

An approach to scalable surface-drifting buoys is needed to enable the high spatial and temporal resolution of oceanographic data that the science and meteorological communities are asking for. With the number of active buoys predicted to increase by a factor of 100 or more, the impact on the environment becomes even more important. Here, we present a pathway to a scalable and sustainable generation of buoys. We identify the main criteria to be used when developing such buoys to be low cost, with reliable data and neutral or even positive environmental impact. For each buoy subsystem—hull, electronics, energy generation and …

Work In Progress: Using Internships As Means For Indirect Assessment Of Abet Criteria 3 “1-7” Student Outcomes, Robert Bass

Electrical and Computer Engineering Faculty Publications and Presentations

The Electrical & Computer Engineering (ECE) Department at Portland State University (PSU) has developed a Power Engineering Internship (PEI) program that provides engineering career development pathways within the electric utility industry. The PEI is supported by several U.S. Department of Energy grants that aim to develop quality career opportunities and develop a future electric utility workforce that represents the nation’s diverse populations. The PSU ECE Department intends to use surveys of internship participants as assessment tools for its ABET accreditation process, in particular, the ABET Criteria 3 Student Outcomes (SOs). SOs relate to the knowledge, skills, and behaviors that students …

An Offline Approach For Frequency Event Detection In Power Systems: Tkeo And Statistical Analysis, Hussain A. Alghamdi, Midrar Adham, Umar Farooq, Robert Bass

Electrical and Computer Engineering Faculty Publications and Presentations

The increasing integration of renewable energy sources in power grids and the transition from conventional thermal-based generation to inverter-based resources for power generation have reduced power system inertia and increased the rate of change of frequency, which constitutes a challenge for frequency stability in modern power systems. These changes necessitate robust frequency event detection algorithms that can rapidly and accurately identify events, providing essential support to maintain stability. This paper proposes a frequency event detection algorithm with six tunable parameters for offline post-processing, leveraging the Teager-Kaiser Energy Operator method and statistical analysis. The algorithm is tested on a dataset comprised …

Grid Services Demonstration Using Service-Oriented Derms, Midrar Adham, Sean Keene, Tylor E. Slay, Jaime T. Kolln, Robert Bass

Electrical and Computer Engineering Faculty Publications and Presentations

This work demonstrates four grid service use cases using a service-oriented DER Management System within an Energy Grid of Things network. Imposed by a set of rules referred to as the Energy Service Interface, the DER Management System uses IEEE 2030.5 as its primary communication protocol. To simulate the efforts of Grid Operators, Grid Service Providers, and consumers to provide grid services, a co-simulation environment that leverages the GridAPPS-D simulation platform was developed. The results show that a service-oriented DER Management System provides a means of achieving reliable and impactful grid services while protecting customers’ privacy and ensuring their agency …

Estimating Electric Power Consumption Of Grid-Enabled Residential Heat Pump Water Heaters, Dana Paresa, Robert Bass

Electrical and Computer Engineering Faculty Publications and Presentations

We present two methods for estimating compressor electric power consumption of residential heat pump water heaters. Power is calculated using data from voltage and current instrumentation, which add costs and potential failure points to the unit. The two methods presented herein use thermal instrumentation or derived data that are typically included within modern residential heat pump water heaters. One method uses data from lower and upper tank temperature sensors. The other method uses an attribute that is commonly available within grid-enabled flexible load heat pump water heaters. For both methods, fit equations were derived, for which coefficients are tuned to …

Computer Vision-Based Framework For Data Extraction From Heterogeneous Financial Tables: A Comprehensive Approach To Unlocking Financial Insights, Iftakhar Ali Khandokar, Priya Deshpande

Electrical and Computer Engineering Faculty Research and Publications

Information extraction from financial document images is crucial in computer vision and NLP, as financial data often exists in image or PDF format, enabling organizations to analyze and make informed business decisions using OCR advancements. The table contents of financial document images are one of the prominent structures to confine important portions of data of the document and many Deep learning-based methods have been proposed to detect Table regions inside document images. The shortcomings of the current approach are that it is bounded within the detection of the table region and struggles in cases such as handling different layouts and …

Advanced Nanocomposite-Based Electrochemical Sensor For Ultra-Sensitive Dopamine Detection In Physiological Fluids, Megha Shinde, Gymama Slaughter

Center for Bioelectronics Publications

This study presents a novel point-of-care electrochemical sensor for dopamine (DA) detection, featuring a flexible laser-induced graphene (LIG) modified with a unique nanocomposite comprising Nb₄C₃T_x MXene, polypyrrole (PPy), and iron nanoparticles (FeNPs). The LIG-Nb₄C₃T_x MXene-PPy-FeNPs is characterized by scanning electron microscopy to confirm the successful surface modification. The electrochemical performance of the fabricated sensor via cyclic voltammetry showed significant electrochemical activity upon Nb₄C₃T_x MXene-PPy-FeNPs nanocomposite modification of the LIG surface with an increased peak anodic current (Ipa) from 43 μA to 104 μA. The sensor …

Behavior Analysis Of Simple And Complex Workloads, Davi D. Dantas

Honors Undergraduate Theses

Complex tasks have evolved rapidly in recent times due to tremendous advancements in computational power and data availability. With the ever-increasing presence of complex applications, this paper attempts to distinguish between complex and simple applications. This paper explored side-channel analysis as a method to differentiate complex workloads from simple workloads by monitoring system-level metrics such as power consumption, cache behavior, and memory accesses. By leveraging side-channel effects such as power analysis and memory access, this study seeks to establish unique hardware signatures for complex workloads. Using tools such as Intel Pin, the data will be collected from complex and simple …

Flame Boundary Effects Of Hydrogen-Air Premixing, Alecson L. De Lima Junior

Honors Undergraduate Theses

The objective of this research was to investigate the reaction of hydrogen and heated air premixing when injected into a combusting ethylene-air crossflow, and to study the flame stabilization location with varying premixing levels. The main parameter of this investigation was the flame stabilization diagnosed through chemiluminescence, based on recorded equivalence ratio, temperature, and flame boundaries, and maintaining a constant air temperature, hydrogen and air mass flow, and momentum flux ratios. Testing was conducted at different ratios of hydrogen and air premixing achieved through alternating the distance between the point where hydrogen and air are mixed and the combusting crossflow. …

Identification Of Fiducial Points In Seismocardiographic Cycles Using Manual And Automated Annotation Methods, Jasmine-Vy T. Truong

Honors Undergraduate Theses

There is currently a need for complementary methods for non-invasive cardiac monitoring. Seismocardiography (SCG), the measurement of cardiac-induced vibrations at the chest surface, has shown potential clinical utility. Improving the reliability of detecting fiducial points of electrocardiography (ECG) and SCG, which collectively capture the electro-mechanical cardiac activities, could expand ECG/SCG utility as a low-cost, accessible tool for clinical assessment. This study identifies commonly accepted criteria for fiducial point detection in SCG and ECG through an extensive literature review and signal processing techniques. The previous criteria were evaluated to identify their strengths and weaknesses. Based on the findings, an improved set …

Safe Data-Enabled Control Of Human-In-The-Loop Robotic Manipulator Systems, Ritirupa Dey, Avimanyu Sahoo, Vignesh Narayanan

Publications

Safe control of human-in-the-loop (HIL) robotic manipulators is critical for applications such as assistive robotics, teleoperation in hazardous environments, and collaborative manufacturing. However, this remains challenging due to the lack of a unified framework that simultaneously addresses safety constraints, external disturbances, unmodeled dynamics, and dynamic role switching in the HIL setting. In this paper, we propose a novel NN-driven HIL control framework in which human–robot dyadic interaction occurs through the haptic channel. Using Lyapunov stability analysis, we theoretically show that the proposed NN-based controller ensures accurate joint trajectory tracking, compensates for system uncertainties, and adapts to human inputs modeled as …

Design Of Fast Start-Up High-Q Oscillator For Wireless Sensor Nodes Transceiver Frequency Reference, Abdolraouf Rahmani

Student Works (2020-2029)

With the prevalence of wireless sensor networks and the Internet of Things (IoT), optimizing power in battery-powered wireless nodes is crucial due to the inconvenience and cost of replacing batteries in remote areas. Synchronized power modulation between "Sleep" and "Active" states, known as burst mode activation, allows nodes to conserve power. However, frequent transitions between these states consume significant energy, highlighting the need to reduce the start-up time of the slowest component, the high-Q crystal oscillator. Additionally, to ensure improved synchronization within the network and a cost-effective IoT device manufacturing, the device should be produced with low start-up time variations …

Bright And Dark Pulsed Fiber Lasers Based On Multimode Interference, Yu Chen

Student Works (2020-2029)

Pulsed lasers, particularly ultrashort pulsed lasers, find widespread application across various fields including telecommunications, bio-imaging, spectroscopy, atmospheric measurements, surgery, and material processing. This study focuses on harnessing the potential of the single mode-multimode-single mode (SMS) structure as a robust avenue for developing simple, compact, and cost-effective bright and dark pulsed erbium-doped fiber lasers (EDFLs). The SMS configuration serves as an ingenious artificial saturable absorber (SA), facilitating the generation of ultrashort pulsed lasers through the Kerr Effect with nonlinear multimode interference. By precisely fusion-splicing single mode fibers to both ends of a designated length of multimode fiber, the SMS architecture is …

Antennas For Emerging Satellite Services, Jakub Przepiorowski

Doctoral

The NewSpace era has revolutionized access to space, driving advancements in satellite communication (SATCOM) systems and creating demand for low-cost, compact, and high-performance user terminals. This thesis addresses these needs by developing innovative antenna solutions tailored for user terminals designed for emerging satellite constellations and satellite Internet-of-Things (S-IoT) applications.

Personalized Persuasion In The Digital Age: A Data-Driven Approach To Effective Communication, Annye Braca

Doctoral

This thesis investigates the potential of Machine Learning (ML) to personalize persuasive marketing messages. It explores the identification of individuals receptive to specific persuasion techniques based on their psychometric profiles. By developing ML models that incorporate these profiles, the thesis aims to predict the impact of tailored messages and improve the effectiveness of marketing communication.