Electrical and Computer Engineering Commons^™

Developments In Lfm-Cw Sar For Uav Operation, Craig Lee Stringham

Theses and Dissertations

Opportunities to use synthetic aperture radar (SAR) in scientific studies and military operations are expanding with the development of small SAR systems that can be operated on small unmanned air vehicles (UAV)s. While the nimble nature of small UAVs make them an attractive platform for many reasons, small UAVs are also more prone to deviate from a linear course due autopilot errors and external forces such as turbulence and wind. Thus, motion compensation and improved processing algorithms are required to properly focus the SAR images. The work of this dissertation overcomes some of the challenges and addresses some of the …

Tincr: Integrating Custom Cad Tool Frameworks With The Xilinx Vivado Design Suite, Brad S. White

Theses and Dissertations

The field programmable gate array (FPGA) is appealing as a computational platform because of its ability to be repurposed for a number of different applications and its relatively low design cost. Traditionally, FPGA vendors provide a set of electronic design automation (EDA) tools to assist customers with the implementation of their designs. These tools are necessarily general purpose, and the resulting tool flow does not provide the user much in the way of customization. Frameworks such as RapidSmith and Torc allow for the creation of custom CAD tools that are able to target actual Xilinx FPGA devices. However, they are …

Secure Degrees Of Freedom For The Mimo Wiretap Channel With A Multiantenna Cooperative Jammer, Mohamed Nafea, Aylin Yener

Electrical and Computer Engineering Faculty Research & Creative Works

A multiple antenna Gaussian wiretap channel with a multiantenna cooperative jammer (CJ) is considered and the secure degrees of freedom (s.d.o.f.), with N antennas at the sender, receiver, and eavesdropper, is derived for all possible values of the number of antennas at the cooperative jammer, K. In particular, the upper and lower bounds for the s.d.o.f. are provided for different ranges of K and shown to coincide. Gaussian signaling both for transmission and jamming is shown to be sufficient to achieve the s.d.o.f. of the channel, when the s.d.o.f. is integer valued. By contrast, when the channel has a non-integer …

A 129nw Neural Amplifier And Gm-C Filter For Eeg Using Gm/Id Methodology, Samuel A. Gallegos

Theses and Dissertations - UTB/UTPA

This Thesis presents a low-power analog front-end amplifier and Gm-C filter for biomedical sensing applications, specifically for Electroencephalogram (EEG) use. The proposed neural amplifier uses a supply voltage of 1.8V, it has a mid-band gain of 40.75dB, and consumes a total current of 71.82nA, for a total dissipated power of 129.276nW. Also presented is the design of a 3rd order Butterworth Low Pass Gm-C Filter which makes use of 14.7nS transconductors; the proposed filter has a pass band suitable for EEG recording use (1-100Hz). The amplifier and filter utilize current sources without bias resistances which provide 56nA and (1.154nA x …

Applications Of Magnetostrictive Materials In The Real-Time Monitoring Of Vehicle Suspension Components, Raul Estrada

Theses and Dissertations - UTB/UTPA

The purpose of this project is to explore applications of magnetostrictive materials for real-time monitoring of railroad suspension components, in particular bearings. Monitoring of such components typically requires the tracking of temperature vibration and load. In addition, real-time, long-term monitoring can be greatly facilitated through the use of wireless, self-powered sensors. Magnetostrictive materials, such as Terfenol-D, have the potential to address both requirements. Currently, piezoelectrics are used for many load and energy harvesting applications; however, they are fragile and are difficult to use for static load measurements. Magnetostrictive metals are tougher, and their property of variable permeability when stressed can …

Optimizing Performance And Scalability On Hybrid Mpsocs, Hongyuan Ding

Graduate Theses and Dissertations

Hardware accelerators are capable of achieving significant performance improvement. But design- ing hardware accelerators lacks the flexibility and the productivity. Combining hardware accelerators with multiprocessor system-on-chip (MPSoC) is an alternative way to balance the flexibility, the productivity, and the performance. However, without appropriate programming model it is still a challenge to achieve parallelism on a hybrid (MPSoC) with with both general-purpose processors and dedicated accelerators. Besides, increasing computation demands with limited power budget require more energy-efficient design without performance degradation in embedded systems and mobile computing platforms. Reconfigurable computing with emerging storage technologies is an alternative to enable the optimization …

A Further Look At Capacitors In Complex Arrangements, Kenneth V. Cartwright, Patrick Russell, Edit J. Kaminsky

Electrical Engineering Faculty Publications

Recently, a previous contributor showed how the delta-wye conversion may be applied to find the equivalent capacitance of five capacitors arranged in a bridge configuration. In fact, that contributor gave an algorithm for this purpose which showed that the equivalent capacitance depends upon all five capacitors. However, in this paper, we point out that there is a special case where the equivalent capacitance does not depend upon one of the five capacitors.

Finding The Minimum Input Impedance Of A Second-Order Twofold-Gain Sallen-Key Low-Pass Filter Without Calculus, Kenneth V. Cartwright, Edit J. Kaminsky

Electrical Engineering Faculty Publications

We derive an expression for the input complex impedance of a Sallen-Key second-order low-pass filter of twofold gain as a function of the natural frequency ωo and the quality factor Q. From this expression, it is shown that the filter behaves like a Frequency Dependent Negative Resistance (FDNR) element for low frequencies and as a single resistor at high frequencies. Furthermore, the minimum input impedance magnitude is found without using calculus. We discovered that the minimum input impedance magnitude is inversely proportional to Q and can be substantially less than its high-frequency value. Approximations to the minimum input impedance and …

Design, Analysis And Implementation Of An Experimental System To Harvest Energy From Atmospheric Temperature Variations Using Ethyl Chloride Filled Bellows, Gibran Ali

All Theses

The increase in global warming and the dwindling supplies of fossil fuels have shifted the focus from traditional to alternate sources of energy. This has resulted in a concerted effort towards finding new energy sources as well as better understanding traditional renewable energy sources such as wind and solar power. In addition to the shift in focus towards alternate energy, the last two decades have offered a dramatic rise in the use of digital technologies such as wireless sensor networks that require small but isolated power supplies. Energy harvesting, a method to gather energy from ambient sources including sunlight, vibrations, …

Remote Sensing Based On Hyperspectral Data Analysis, Ershad Sharifahmadian

UNLV Theses, Dissertations, Professional Papers, and Capstones

In remote sensing, accurate identification of far objects, especially concealed objects is difficult. In this study, to improve object detection from a distance, the hyperspecral imaging and wideband technology are employed with the emphasis on wideband radar. As the wideband data includes a broad range of frequencies, it can reveal information about both the surface of the object and its content. Two main contributions are made in this study:

1) Developing concept of return loss for target detection: Unlike typical radar detection methods which uses radar cross section to detect an object, it is possible to enhance the process of …

Simulation, And Overload And Stability Analysis Of Continuous Time Sigma Delta Modulator, Kyung Kang

UNLV Theses, Dissertations, Professional Papers, and Capstones

The ever increasing demand for faster and more powerful digital applications requires high speed, high resolution ADCs. Currently, sigma delta modulators ADCs are extensively used in broadband telecommunication systems because they are an effective solution for high data-rate wireless communication systems that require low power consumption, high speed, high resolution, and large signal bandwidths.

Because mixed-signal integrated circuits such as Continuous Time sigma delta modulators contain both analog and digital circuits, mixed signal circuits are not as simple to model and simulate as all discrete or all analog systems. In this dissertation, the delta transform is used to simulate CT …

Shape/Image Registration For Medical Imaging : Novel Algorithms And Applications., Ahmed Magdy Shalaby 1982-

Electronic Theses and Dissertations

This dissertation looks at two different categories of the registration approaches: Shape registration, and Image registration. It also considers the applications of these approaches into the medical imaging field. Shape registration is an important problem in computer vision, computer graphics and medical imaging. It has been handled in different manners in many applications like shapebased segmentation, shape recognition, and tracking. Image registration is the process of overlaying two or more images of the same scene taken at different times, from different viewpoints, and/or by different sensors. Many image processing applications like remote sensing, fusion of medical images, and computer-aided surgery …

Multilayer Electret Activated By Direct Contact Silicon Electrode., Mark M. Crain

Electronic Theses and Dissertations

Electrets used in microelectromechanical systems (MEMS) devices are often formed by corona charging, where ionized gases are generated in an electric field to introduce a charge to the electret surface. The purpose of this study was to investigate a new technique for creating an electret from a plasma enhanced chemical vapor deposition (PECVD) multilayer film of SiO2/Si3N4/SiO2 using a direct contact electrode of silicon. The electret formation takes advantage of deep traps in silicon nitride, which are known to develop from hydrogen interactions with silicon dangling bonds and, in some stoichiometries, nitrogen dangling bonds. The electret activation process has been …

Wirelessly Controlled Smart Outlet, Andrew Godsil, Ariel Dubinsky

Electrical Engineering

Popularity of home automation devices has increased greatly in recent years due to higher affordability and simplicity through smartphone and tablet connectivity. For the purpose of this experiment, we have developed the Smart Outlet: a stand-alone communication unit, used to connect home outlets to the internet. The Smart Outlet controls lighting and simple appliances throughout the home, remotely, using wireless commands from the web. A Google Calendar interface directly controls the outlets’ function by scheduling them with dedicated calendar events. The calendar’s interface can even be accessed from multiple different platforms (i.e. phones, computers, tablets) for the convenience of all …

Transimpedance Amplifier For Polymer Photodiodes, Sheridan Knighton

Electrical Engineering

Dr. Braun’s students in the Polymer Electronics Lab currently have a way to measure the light intensity from their light emitting devices however it consumes an unnecessary amount of space and power. I offer to improve upon the existing transimpedance circuit that Dr. Braun currently uses, reducing the total space occupied by the circuit and the power consumption of the current setup. The transimpedance circuit measures the incidence light intensity from the polymer-based photo detector and outputs an accurate, discrete, and measurable voltage. The current setup however utilizes two 20V wall warts for the positive and negative rails of the …

Microprocessor Management Of Energy Harvesting Buck Boost Converters, Timothy O'Sullivan

Electrical Engineering

No abstract provided.

High Voltage Pulse-Width Generator For The Algae Biofuel Project, Philip Yu, Stephen Leung

Electrical Engineering

This purpose of this project, sponsored by Boeing and advised by Dr. Arakaki and Dr. Taufik, is to build a high voltage pulse width generator that lyses algae cells to harvest the biofuel within. This project uses Emmanuel Loza's thesis on a cascaded high voltage converter with variable control to build a portable pulse width generator with independent control on the peak voltage, pulse width, and frequency. The project focuses on creating a pulse width generator capable of finding the most optimal pulsed electric field to lyse algae. The pulse width module ranges from 10V-80V peak voltage, 60Hz-100 kHz frequency, …

Mega: An Energy Aware Algorithm For Self-Powered Wireless Sensor Networks In Sustainable Smart Infrastructure, Dong Qi, Yu Chen, Shahrzad Towfighian

Mechanical Engineering Faculty Scholarship

Smart infrastructure is attractive for possessing many desirable features, such as uninterrupted monitoring of health conditions, timely response to damages, and human-infrastructure interactions. Embedded sensors that collectinformation are critical for decision making. However, the lifetime of electronic sensors is a constraint to infrastructure lifetime if sensors are physically embedded in the infrastructure at construction time. In this paper, we studied a self-powered wireless sensor network that harvests energy from mechan-ical vibration in the environment. A dynamic, hierarchical algorithm called MEGA is proposed that constructs clusters and elects the cluster head based on residue energy and energy harvest rate. Taking a …

A Study Of The Regularity Of Autocorrelation Of Manipulation Of Wrist Motion During Eating, Xueting Yu

All Theses

This thesis considers the problem of detecting the eating activities (e.g. meals, snacks) of people by tracking their wrist motion. Our goal is to automatically de- tect the start and end times of eating activities during free-living. It builds upon previous work done by our research group [6] [7] [8] [21]. The detection is done by segmenting data into segments then classifying the segments as EA (eating activity) and NonEA (non-eating activity) using a Bayesian classier. Previous features used in the classier developed by our group included the sum of acceleration, the amount of manipulation, the amount of wrist roll …

Numerical Simulation Of The Heat Leakage At The Gasket Region Of Domestic Refrigerators, Feng Gao

All Theses

Computational Fluid Dynamics (CFD) simulations are performed to investigate the heat loss at the gasket of a standard over/under domestic refrigerator. The study numerically simulates a unique experimental test cell with only the gasket region exposed to the ambient environment and other parts protected by insulation (see picture below). The test cell is cubic with an interior cavity having dimensions 2' x 2' x 2' within which a heating element is placed to create a specified temperature difference. A matching set of door and side panels exposes a 2' width of the gasket region to heat transfer with the surroundings. …

A Device To Record Naturally Daily Wrist Motion, Surya Sharma

All Theses

We introduce a new device to record and store wrist motion activity data. The motivation to create this device was the fact that this data can be used to detect periods of eating or the number of bites consumed. There is no similar device available in the market. This device uses new components that have been recently introduced to the market, and newer techniques that can be used for low quantity production. The production cost for this device was $52, similar to other fitness trackers on the market. The device was capable of recording wrist motion activity for 24 hours …

Steps Toward A Net-Zero Campus With Renewable Energy Resources, Andrew Clarke

All Dissertations

With the increasing attention and support behind plug in hybrid electric vehicles, research must be conducted to examine the impacts of vehicles on electric distribution and transmission systems. This research aims first to model the behavior of vehicle battery chargers during system disturbances and mitigate any impacts. A distribution test system example is modeled and several different vehicle charger topologies are added. Faults are applied to the distribution system with vehicle chargers connected and the results are examined. Based on these results, a control strategy to mitigate their negative impacts is suggested. Photovoltaic panels are then added to the system …

Studies Of Imbalance Difference Theory In Modeling Conversion Between Differential Mode And Common Mode Signals, Li Niu

All Dissertations

This dissertation describes three related studies regarding the imbalance difference theory in modeling the conversion between differential mode and common mode/antenna mode signals. The topics covered are: rigorous derivation of imbalance difference theory for modeling radiated emission problems, modeling the conversion between differential mode and common mode propagation in transmission lines, and modeling the loading impedance on differential mode signals due to radiated emissions. The imbalance difference theory describes a method for calculating the coupling between differential mode signals and common mode signals due to changes in electrical balance on a transmission line. It provides both physical insight and a …

High Frequency Devices And Circuit Modules For Biochemical Microsystems, Jiwei Sun

All Dissertations

This dissertation investigates high frequency devices and circuit modules for biochemical microsystems. These modules are designed towards replacing external bulky laboratory instruments and integrating with biochemical microsystems to generate and analyze signals in frequency and time domain. The first is a charge pump circuit with modified triple well diodes, which is used as an on-chip power supply. The second is an on-chip pulse generation circuit to generate high voltage short pulses. It includes a pulse-forming-line (PFL) based pulse generation circuit, a Marx generator and a Blumlein generator. The third is a six-port circuit based on four quadrature hybrids with 2.0~6.0 …

A Comprehensive Assessment Methodology Based On Life Cycle Analysis For On-Board Photovoltaic Solar Modules In Vehicles, Mahmoud Abdelhamid

All Dissertations

This dissertation presents a novel comprehensive assessment methodology for using on-board photovoltaic (PV) solar technologies in vehicle applications. A well-to-wheels life cycle analysis based on a unique energy, greenhouse gas (GHG) emission, and economic perspective is carried out in the context of meeting corporate average fuel economy (CAFE) standards through 2025 along with providing an alternative energy path for the purpose of sustainable transportation. The study includes 14 different vehicles, 3 different travel patterns, in 12 U.S. states and 16 nations using 19 different cost analysis scenarios for determining the challenges and benefits of using on-board photovoltaic (PV) solar technologies …

Modeling Sustainability In Renewable Energy Supply Chain Systems, Fei Xie

All Dissertations

This dissertation aims at modeling sustainability of renewable fuel supply chain systems against emerging challenges. In particular, the dissertation focuses on the biofuel supply chain system design, and manages to develop advanced modeling framework and corresponding solution methods in tackling challenges in sustaining biofuel supply chain systems. These challenges include: (1) to integrate 'environmental thinking' into the long-term biofuel supply chain planning; (2) to adopt multimodal transportation to mitigate seasonality in biofuel supply chain operations; (3) to provide strategies in hedging against uncertainty from conversion technology; and (4) to develop methodologies in long-term sequential planning of the biofuel supply chain …

Earth Abundant Thin Film Technology For Next Generation Photovoltaic Modules, Githin Alapatt

All Dissertations

With a cumulative generation capacity of over 100 GW, Photovoltaics (PV) technology is uniquely poised to become increasingly popular in the coming decades. Although, several breakthroughs have propelled PV technology, it accounts for only less than 1% of the energy produced worldwide. This aspect of the PV technology is primarily due to the somewhat high cost per watt, which is dependent on the efficiency of the PV cells as well as the cost of manufacturing and installing them. Currently, the efficiency of the PV conversion process is limited to about 25% for commercial terrestrial cells; improving this efficiency can increase …

Life Cycle Assessment Projection Of Photovoltaic Cells: A Case Study On Energy Demand Of Quantum Wire Based Photovoltaic Technology Research, Shilpi Mukherjee

Graduate Theses and Dissertations

With increasing clean-energy demand, photovoltaic (PV) technologies have gained attention as potential long-term alternative to fossil fuel energy. However, PV research and manufacture still utilize fossil fuel-powered grid electricity. With continuous enhancement of solar conversion efficiency, it is imperative to assess whether overall life cycle efficiency is also being enhanced. Many new-material PV technologies are still in their research phase, and life cycle analyses of these technologies have not yet been performed. For best results, grid dependency must be minimized for PV research, and this can be accomplished by an analytical instrument called Life Cycle Assessment (LCA).

LCA is the …

Thermal Analysis, Parasitic Extraction, And Wirebond Reliability Studies Of Power Electronic Modules, Shilpa Prabhudeva

Graduate Theses and Dissertations

This thesis research investigates thermal performance, parasitic extraction and wirebond/encapsulation reliability of power electronic modules. Thermal performance is critical to the power electronic modules. As such, thermal analysis is an important part of the power electronic module design process. Several cases are studied on generalized power modules with a full bridge layout. A database is built based on these results. The studies are performed using SolidWorks thermal simulation tool. The database involves several parameters such as power dissipation, maximum junction temperature, ambient temperature, convection coefficient required to cool the module, size of the baseplate, heat-sink size, substrate size, spacing between …

Technology Mapping, Design For Testability, And Circuit Optimizations For Null Convention Logic Based Architectures, Farhad Alibeygi Parsan

Graduate Theses and Dissertations

Delay-insensitive asynchronous circuits have been the target of a renewed research effort because of the advantages they offer over traditional synchronous circuits. Minimal timing analysis, inherent robustness against power-supply, temperature, and process variations, reduced energy consumption, less noise and EMI emission, and easy design reuse are some of the benefits of these circuits. NULL Convention Logic (NCL) is one of the mainstream asynchronous logic design paradigms that has been shown to be a promising method for designing delay-insensitive asynchronous circuits.

This dissertation investigates new areas in NCL design and test and is made of three sections. The first section discusses …