Electrical and Computer Engineering Commons^™

Cross-Layer Design For Mobile Ad-Hoc Unmanned Aerial Vehicle Communication Networks, Abdel Ilah Nour Alshbatat

Dissertations

Mobile Ad-Hoc network (MANET) is a popular type of wireless network that is formed by a collection of mobile nodes. Each node in such a network has the capability to communicate with its neighbors and non-neighbors through a wireless medium without using any existing network infrastructure. Due to the lack of infrastructure, all nodes in Ad-Hoc network are designed to act as an end system and a router for other nodes.

Traditionally, the dominant design methodology for network protocols was based on the open systems interconnection (OSI) reference model. This methodology divided the stack into seven layers in which each …

Preserving Useful Info While Reducing Noise Of Physiological Signals By Using Wavelet Analysis, Jeffrey Lam

UNF Graduate Theses and Dissertations

Wavelet analysis is a powerful mathematical tool commonly used in signal processing applications, such as image analysis, image compression, image edge detection, and communications systems. Unlike traditional Fourier analysis, wavelet analysis allows for multiple resolutions in the time and frequency domains; it can preserve time information while decomposing a signal spectrum over a range of frequencies. Wavelet analysis is also more suitable for detecting numerous transitory characteristics, such as drift, trends, abrupt changes, and beginnings and ends of events. These characteristics are often the most important and critical part of some non-stationary signals, such as physiological signals. The thesis focuses …

Time-Domain Modeling Of High-Frequency Electromagnetic Wave Propagation, Overhead Wires, And Earth, Nils Markus Stenvig

Dissertations, Master's Theses and Master's Reports - Open

Prediction of radiated fields from transmission lines has not previously been studied from a panoptical power system perspective. The application of BPL technologies to overhead transmission lines would benefit greatly from an ability to simulate real power system environments, not limited to the transmission lines themselves. Presently circuitbased transmission line models used by EMTP-type programs utilize Carson’s formula for a waveguide parallel to an interface. This formula is not valid for calculations at high frequencies, considering effects of earth return currents.

This thesis explains the challenges of developing such improved models, explores an approach to combining circuit-based and electromagnetics modeling …

Multi-Software Modeling Technique For Field Distribution Propagation Through An Optical Vertical Interconnect Assembly, Matthew D. Howard

Dissertations, Master's Theses and Master's Reports - Open

Embedded siloxane polymer waveguides have shown promising results for use in optical backplanes. They exhibit high temperature stability, low optical absorption, and require common processing techniques. A challenging aspect of this technology is out-of-plane coupling of the waveguides. A multi-software approach to modeling an optical vertical interconnect (via) is proposed. This approach utilizes the beam propagation method to generate varied modal field distribution structures which are then propagated through a via model using the angular spectrum propagation technique. Simulation results show average losses between 2.5 and 4.5 dB for different initial input conditions. Certain configurations show losses of less than …

Compressed Sensing Approach To Ultra-Wideband Receiver Design, Jodhbir Singh

Dissertations, Master's Theses and Master's Reports - Open

One of the scarcest resources in the wireless communication system is the limited frequency spectrum. Many wireless communication systems are hindered by the bandwidth limitation and are not able to provide high speed communication. However, Ultra-wideband (UWB) communication promises a high speed communication because of its very wide bandwidth of 7.5GHz (3.1GHz-10.6GHz). The unprecedented bandwidth promises many advantages for the 21st century wireless communication system.

However, UWB has many hardware challenges, such as a very high speed sampling rate requirement for analog to digital conversion, channel estimation, and implementation challenges. In this thesis, a new method is proposed using compressed …

Fading Pdf Of Free-Space Optical Communication System With Pointing Error, Rui Liao

Dissertations, Master's Theses and Master's Reports - Open

A free-space optical (FSO) laser communication system with perfect fast-tracking experiences random power fading due to atmospheric turbulence. For a FSO communication system without fast-tracking or with imperfect fast-tracking, the fading probability density function (pdf) is also affected by the pointing error. In this thesis, the overall fading pdfs of FSO communication system with pointing errors are calculated using an analytical method based on the fast-tracked on-axis and off-axis fading pdfs and the fast-tracked beam profile of a turbulence channel. The overall fading pdf is firstly studied for the FSO communication system with collimated laser beam. Large-scale numerical wave-optics simulations …

Direction Finding In The Presence Of A More Realistic Environment Model, Irfan Ahmed

Dissertations, Master's Theses and Master's Reports - Open

Direction-of-arrival (DOA) estimation is susceptible to errors introduced by the presence of real-ground and resonant size scatterers in the vicinity of the antenna array. To compensate for these errors pre-calibration and auto-calibration techniques are presented. The effects of real-ground constituent parameters on the mutual coupling (MC) of wire type antenna arrays for DOA estimation are investigated. This is accomplished by pre-calibration of the antenna array over the real-ground using the finite element method (FEM). The mutual impedance matrix is pre-estimated and used to remove the perturbations in the received terminal voltage. The unperturbed terminal voltage is incorporated in MUSIC algorithm …

Tracking A Non-Cooperative Target Using A Doppler Radar Wireless Sensor Network, Michael K. Blaser

Dissertations, Master's Theses and Master's Reports - Open

Tracking or target localization is used in a wide range of important tasks from knowing when your flight will arrive to ensuring your mail is received on time. Tracking provides the location of resources enabling solutions to complex logistical problems. Wireless Sensor Networks (WSN) create new opportunities when applied to tracking, such as more flexible deployment and real-time information. When radar is used as the sensing element in a tracking WSN better results can be obtained; because radar has a comparatively larger range both in distance and angle to other sensors commonly used in WSNs. This allows for less nodes …

Detection Of Complex Point Targets With Distributed Assets In A Mimo Radar System, Ishtiaque Amin

Dissertations, Master's Theses and Master's Reports - Open

The report explores the problem of detecting complex point target models in a MIMO radar system. A complex point target is a mathematical and statistical model for a radar target that is not resolved in space, but exhibits varying complex reflectivity across the different bistatic view angles. The complex reflectivity can be modeled as a complex stochastic process whose index set is the set of all the bistatic view angles, and the parameters of the stochastic process follow from an analysis of a target model comprising a number of ideal point scatterers randomly located within some radius of the targets …

Atp Modeling Of Internal Transformer Faults For Relay Performance Testing, Elizaveta O. Egorova

Dissertations, Master's Theses and Master's Reports - Open

Transformers are very important elements of any power system. Unfortunately, they are subjected to through-faults and abnormal operating conditions which can affect not only the transformer itself but also other equipment connected to the transformer. Thus, it is essential to provide sufficient protection for transformers as well as the best possible selectivity and sensitivity of the protection. Nowadays microprocessor-based relays are widely used to protect power equipment. Current differential and voltage protection strategies are used in transformer protection applications and provide fast and sensitive multi-level protection and monitoring. The elements responsible for detecting turn-to-turn and turn-to-ground faults are the negative-sequence …

Forward Error Correction In Memoryless Optical Modulation, David Rhys Jones

UNF Graduate Theses and Dissertations

The unprecedented growth in demand for digital media has led to an all-time high in society’s demand for information. This demand will in all likelihood continue to grow as technology such as 3D television service, on-demand video and peer-to-peer networking continue to become more common place. The large amount of information required is currently transmitted optically using a wavelength division multiplexing (WDM) network structure. The need to increase the capacity of the existing WDM network infrastructure efficiently is essential to continue to provide new high bandwidth services to end-users, while at the same time minimizing network providers’ costs. In WDM …

Modeling Of Novel Coaxial Cable Bragg Grating Sensor By Coupled Mode Theory, Songping Wu

Doctoral Dissertations

"A new sensor based on the novel concept of coaxial cable Bragg grating (CCBG) has been developed for the integrity of civil infrastructure monitoring. In this dissertation work, fundamental research is conducted in sensor modeling and applications, which correspond to the first four papers of the dissertation. A coupled mode theory (CMT) is first applied to establish a physics-based model for CCBG. A numerical solution of the coupled wave equations for CCBG has been derived and validated. As an indicator of sensor sensitivity, the quality factor (Q-factor) of CCBG as a function of sensor structural/material parameters was analytically investigated by …

Electronically Enhanced Surface Diffusion During Ge Growth On Si(100), Ali Orguz Er, Hani E. Elsayed-Ali

Physics Faculty Publications

The effect of nanosecond pulsed laser excitation on surface diffusion during the growth of Ge on Si(100) at 250 °C was studied. In situ reflection high-energy electron diffraction was used to measure the surface diffusion coefficient while ex situ atomic force microscopy was used to probe the structure and morphology of the grown quantum dots. The results show that laser excitation of the substrate increases the surface diffusion during the growth of Ge on Si(100), changes the growth morphology, improves the crystalline structure of the grown quantum dots, and decreases their size distribution. A purely electronic mechanism of enhanced surface …

Structural Characterization Of Nb Films Deposited By Ecr Plasma Energetic Deposition On Crystalline Insulators, Xin Zhao, A. -M. Valente-Feliciano, J. K. Spradlin, H. L. Phillips, C. E. Reece, D. Gu, H. Baumgart, K. Seo

Physics Faculty Publications

An energetic condensation thin film coating technique with an electron cyclotron resonance (ECR) induced Niobium (Nb) plasma ion source is used to deposit Nb thin films on crystalline insulating substrates, such as a-plane and c-plane sapphire (Al₂O₃) and on magnesium oxide, MgO (100), (110), and (111).

Hetero-epitaxial Nb films were produced by ECR deposition with regulated substrate temperature. The residual resistivity ratio (RRR) of about 1 micron thick films on a-plane (1,1,-2,0) sapphire substrates reach values (350 - 450) comparable to high RRR bulk NB commonly used for SRF cavities.

The epitaxial relationship of Nb/crystalline substrate is found to be …

Robust Adaptive Filtering Algorithms For System Identification And Array Signal Processing In Non-Gaussian Environment, Tiange Shao

Doctoral Dissertations

"This dissertation proposes four new algorithms based on fractionally lower order statistics for adaptive filtering in a non-Gaussian interference environment. One is the affine projection sign algorithm (APSA) based on L₁ norm minimization, which combines the ability of decorrelating colored input and suppressing divergence when an outlier occurs. The second one is the variable-step-size normalized sign algorithm (VSS-NSA), which adjusts its step size automatically by matching the L₁ norm of the a posteriori error to that of noise. The third one adopts the same variable-step-size scheme but extends L₁ minimization to Lp minimization and the variable step-size normalized fractionally lower-order …

Impact Of Stochastic Loads And Generations On Power System Transient Stability, Theresa Odun-Ayo

Doctoral Dissertations

"Randomness in physical systems is usually ultimately attributed to external noise. Dynamic systems are driven not only by our own control inputs, but also disturbances which cannot be modeled deterministically. A linear system model is justifiable for a number of reasons, often such a model is adequate for the purpose at hand, and when non-linearities do exist, the typical engineering approach is to linearize about some nominal point or trajectory to achieve a perturbation or error model. However, in order for the resulting model to fit data generated by the real world, these disturbances need to be modeled stochastically. The …

Hardware Emulation Of Wireless Communication Fading Channels, Fei Ren

Doctoral Dissertations

"This dissertation investigates several main challenges to implementing hardware-based wireless fading channel emulators with emphasis on incorporating accurate correlation properties. Multiple-input multiple-output (MIMO) fading channels are usually triply-selective with three types of correlation: temporal correlation, inter-tap correlation, and spatial correlation. The proposed emulators implement the triply-selective fading Channel Impulse Response (CIR) by incorporating the three types of correlation into multiple uncorrelated frequency-flat Rayleigh fading waveforms while meeting real-time requirements for high data-rate, large-sized MIMO, and/or long CIR channels. Specifically, mixed parallel-serial computational structures are implemented for Kronecker products of the correlation matrices, which makes the best tradeoff between computational speed …

Development Of A Fuel Cell Plug-In Hybrid Electric Vehicle And Vehicle Simulator For Energy Management Assessment, Andrew Meintz

Doctoral Dissertations

"This dissertation offers a description of the development of a fuel cell plug-in hybrid electric vehicle focusing on the propulsion architecture selection, propulsion system control, and high-level energy management. Two energy management techniques have been developed and implemented for real-time control of the vehicle. The first method is a heuristic method that relies on a short-term moving average of the vehicle power requirements. The second method utilizes an affine function of the short-term and long-term moving average vehicle power requirements. The development process of these methods has required the creation of a vehicle simulator capable of estimating the effect of …

Guiding Electric Fields For Electroporation Applications, Jose Rey

USF Tampa Graduate Theses and Dissertations

Electroporation is the critical step in an electric field mediated drug or gene delivery protocol. Electroporation based protocols have been successfully demonstrated in cancer clinical trials, however, its impact in other applications is still under investigation. A significant roadblock to long term functioning of implantable biosensors in vivo is the tissue reaction in the form of fibrous encapsulation that results in reduced transport to the sensing element of the biosensor. In vivo gene electroporation has a great potential as a means to modify the transport properties of tissues in the proximity of the sensing element of implantable biosensors.

This dissertation …

Atrial Fibrillation Signal Analysis, Raja Sarath Chandra Prasad Vaizurs

USF Tampa Graduate Theses and Dissertations

Atrial fibrillation (AF) is the most common type of cardiac arrhythmia encountered in clinical practice and is associated with an increased mortality and morbidity. Identification of the sources of AF has been a goal of researchers for over 20 years. Current treatment procedures such as Cardio version, Radio Frequency Ablation, and multiple drugs have reduced the incidence of AF. Nevertheless, the success rate of these treatments is only 35-40% of the AF patients as they have limited effect in maintaining the patient in normal sinus rhythm. The problem stems from the fact that there are no methods developed to analyze …

Diamond Based-Materials: Synthesis, Characterization And Applications, Qiang Hu

USF Tampa Graduate Theses and Dissertations

The studies covered in this dissertation concentrate on the various forms of diamond films synthesized by chemical vapor deposition (CVD) method, including microwave CVD and hot filament CVD. According to crystallinity and grain size, a variety of diamond forms primarily including microcrystalline (most commonly referred to as polycrystalline) and nanocrystalline diamond films, diamond-like carbon (DLC) films were successfully synthesized. The as-grown diamond films were optimized by changing deposition pressure, volume of reactant gas hydrogen (H2) and carrier gas argon (Ar) in order to get high-quality diamond films with a smooth surface, low roughness, preferred growth orientation and high sp3 bond …

Fabrication And Characterization Of Novel 2sss Cigs Thin Film Solar Cells For Large-Scale Manufacturing, Keshavanand Jayadevan

USF Tampa Graduate Theses and Dissertations

A novel 2SSS (2 Step Solid Selenization) CIGS (Cu, In, Ga, Se) thin film solar cell recipe was developed which can be a replacement to the conventional co-deposition process usually employed for large-scale manufacturing. The co-deposition procedure is faced with multiple problems such as selenium incorporation, effective gallium incorporation in the absorber. It is a 2-step proprietary procedure with better control over growth mechanisms and material utilization for the absorber layer for the CIGS thin film solar cells. It makes use of solid selenium source as preferred by manufacturers. Each step of the 2-step procedure was dealt with separately for …

Fabrication And Characterization Of Electrospun Cactus Mucilage Nanofibers, Yanay Pais

USF Tampa Graduate Theses and Dissertations

This work seeks to fabricate, optimize, and characterize nanofibers of cactus Opuntia ficus-indica mucilage and Poly (vinyl alcohol) (PVA) by electrospinning. Mucilage is a neutral mixture of sugars produced by cactus and PVA is a non-toxic, water-soluble, synthetic polymer, which is widely used as a co-spinning agent for polymers. Mucilage was extracted from the cactus pad and prepared for electrospinning by mixing with acetic acid. Two types of PVA were used differentiating in high and low molecular weights. Concentrations of PVA were varied to find an adequate threshold for fiber formation. Changing the ratio of PVA to cactus mucilage produced …

Molybdenum Nitride Films In The Back Contact Structure Of Flexible Substrate Cdte Solar Cells, Vasudha Guntur

USF Tampa Graduate Theses and Dissertations

CdTe solar cells in the superstrate configuration have achieved record efficiencies of 16% but those in the substrate configuration have reached efficiencies of only 7.8%. A major reason for the lower efficiency of substrate CdTe solar cells is the poor back contact. In this work, CdTe solar cells of the substrate configuration have been fabricated on flexible metallic substrates. For this type of devices, impurity diffusion out of stainless-steel substrates due to high temperature processing can be a cause for poor cell performance. It is necessary to investigate ways of improving the back contact by trying to mitigate the above …

Quantitative Carré Differential Interference Contrast Microscopy To Assess Phase And Amplitude, Donald D. Duncan, David G. Fischer, Amanda Dayton, Scott A. Prahl

Electrical and Computer Engineering Faculty Publications and Presentations

We present a method of using an unmodified differential interference contrast microscope to acquire quantitative information on scatter and absorption of thin tissue samples. A simple calibration process is discussed that uses a standard optical wedge. Subsequently, we present a phase-stepping procedure for acquiring phase gradient information exclusive of absorption effects. The procedure results in two-dimensional maps of the local angular (polar and azimuthal) ray deviation. We demonstrate the calibration process, discuss details of the phase-stepping algorithm, and present representative results for a porcine skin sample.

Extraction Of Small Boat Harmonic Signatures From Passive Sonar, George Lloyd Ogden, Lisa M. Zurk, M. E. Jones, M. E. Peterson

Electrical and Computer Engineering Faculty Publications and Presentations

This paper investigates the extraction of acoustic signatures from small boats using a passive sonar system. Noise radiated from a small boats consists of broadband noise and harmonically related tones that correspond to engine and propeller specifications. A signal processing method to automatically extract the harmonic structure of noise radiated from small boats is developed. The Harmonic Extraction and Analysis Tool (HEAT) estimates the instantaneous fundamental frequency of the harmonic tones, refines the fundamental frequency estimate using a Kalman filter, and automatically extracts the amplitudes of the harmonic tonals to generate a harmonic signature for the boat. Results are presented …

Phase Noise In Cmos Phase-Locked Loop Circuits, Yang Liu

LSU Doctoral Dissertations

Phase-locked loops (PLLs) have been widely used in mixed-signal integrated circuits. With the continuously increasing demand of market for high speed, low noise devices, PLLs are playing a more important role in communications. In this dissertation, phase noise and jitter performances are investigated in different types of PLL designs. Hot carrier and negative bias temperature instability effects are analyzed from simulations and experiments. Phase noise of a CMOS phase-locked loop as a frequency synthesizer circuit is modeled from the superposition of noises from its building blocks: voltage-controlled oscillator, frequency divider, phase-frequency detector, loop filter and auxiliary input reference clock. A …

Resource Allocation Methodologies With Fractional Reuse Partitioning In Cellular Networks, Hazar Aki

USF Tampa Graduate Theses and Dissertations

Conventional cellular systems have not taken full advantage of fractional frequency reuse and adaptive allocation due to the fixed cluster size and uniformed channel assignment procedures. This problem may cause more fatal consequences considering the cutting-edge 4G standards which have higher data rate requirements such as 3GPP-LTE and IEEE 802.16m (WiMAX). In this thesis, three different partitioning schemes for adaptive clustering with fractional frequency reuse were proposed and investigated. An overlaid cellular clustering scheme which uses adaptive fractional frequency reuse factors would provide a better end-user experience by exploiting the high level of signal to interference ratio (SIR). The proposed …

Application Of Spatial Bandwidth Concepts To Mas Pole Location For Dielectric Cylinders, James Richie

Electrical and Computer Engineering Faculty Research and Publications

The concept of effective spatial bandwidth (EBW) is extended from the case of an MAS solution for perfectly conducting (PEC) cylinders to dielectric cylinders. It is shown that the ideas and results for the conducting cylinder apply in a straightforward manner to the dielectric case. For the dielectric case, there are two auxiliary surfaces. Because the EBW calculations are independent of the scatterer material, the auxiliary surface for the scattered field will follow the same guidelines for both the PEC and dielectric cases. The guidelines for the second auxiliary surface are described and verified here. Guidelines for both a plane …

Resource Allocation And Efficient Routing In Wireless Networks, Jianjun Yang

University of Kentucky Doctoral Dissertations

In wireless networks, devices (nodes) are connected by wireless links. An important issue is to set up high quality (high bandwidth) and efficient routing paths when one node wants to send packets to other nodes. Resource allocation is the foundation to guarantee high quality connections. In addition, it is critical to handle void areas in order to set up detour-free paths. Moreover, fast message broadcasting is essential in mobile wireless networks. Thus, my research includes dynamic channel allocation in wireless mesh networks, geographic routing in Ad Hoc networks, and message broadcasting in vehicular networks.

The quality of connections in a …