Electrical and Computer Engineering Commons^™

Influence Of Voltage Source Pulse Width Modulated Switching And Induction Motor Circuit On Harmonic Current Content, Martin T. Lange

Browse all Theses and Dissertations

The purpose of this research is to present analysis of the harmonic content present in the phase current of a three phase induction motor while being powered by a voltage source pulse-width modulated (PWM) variable speed drive (VSD). First, the topology and circuit of the drive, its operational fundamentals and waveform appearance are presented and discussed. Next, the three-phase induction motor circuit model and operational characteristics are discussed. Finally, the harmonic content present in the induction motor phase current is determined by use of the PSPICE model. The ability of the PSICE simulation to determine harmonic content is established. It …

Simultaneous Rf/Eo Tracking And Characterization Of Dismounts, Jason M. Blackaby

Browse all Theses and Dissertations

This thesis discusses the fusion of radar frequency(RF) data and electro-optical (EO) data for tracking and characterization of dismounts (i.e., humans). Each of these sensor modalities provides unique information about the location, structure, and movement of a dismount. The person's location is tracked on the 2D ground plane using RF data for range measurements and EO data for angle measurements. Using this information, measurements are made on the structure and dynamic motion (gait) of the person. An imaging approach is used to create spatio-temporal activity maps along with a three-dimensional reconstruction of the dismount.

Intelligent Spectrum Sensor Radio, Omer Mian

Browse all Theses and Dissertations

A cognitive radio is a radio with built-in intelligence that makes it able to utilize the radio frequency spectrum more efficiently by adapting to the changing conditions and frequency availability. In this thesis a spectrum sensor radio is designed that detects transmissions in FM band and determine the range of used and unused frequencies within the band. The radio then starts a transmission on a frequency among the available frequencies. This intelligent radio system design is implemented using the Universal Software Radio Peripheral and GNU Radio with a program written in python that uses a number of GNU Radio modules …

Design Of A Cmos Rf Front End Receiver In 0.18Μm Technology, Vishwas Kudur Sastry

Browse all Theses and Dissertations

An RF front end receiver system refers to the analog down conversion stages of the wireless communication system. The Digital base-band signals cannot be transmitted directly through wireless channels due to the properties of electromagnetic waves. The baseband signals need to be converted to analog through a digital-to-analog converter (DAC), up converted to higher frequency using an up conversion mixer and then transmitted through the channel. The received signals are down converted to base band frequency and then converted to digital again using the analog to digital converter (ADC). The processes which the analog signal undergoes at the RF front …

Fpga Design Of A Hardware Efficient Pipelined Fft Processor, Ryan T. Bone

Browse all Theses and Dissertations

Digital receivers involve fast Fourier transform (FFT) computations that require a large amount of arithmetic operations. The implementation of a FFT processor is one of the most challenging parts in the realization of a wideband receiver and its hardware complexity is very high. Hence, kernel function FFT processors have been proposed to meet real-time processing requirements and to reduce hardware complexity by rounding the kernel function to predetermined kernel points so as to eliminate the multipliers and use only shifters and adders or subtractors. Because of the nonlinear nature of this approximation by the rounding errors, spurious responses are generated …

A Novel Accurate Approximation Method Of Lognormal Sum Random Variables, Xue Li

Browse all Theses and Dissertations

Sums of lognormal random variables occur in many problems in wireless communications due to large-scale signal shadowing from multiple transmitters. With the emerging of cognitive radio technology, accurate analysis of interferences from multiple primary users and multiple secondary users is required. Such interferences are well modeled by the lognormal sum distribution. The lognormal sum distribution is known to have no close-form and is difficult to compute numerically. Several approximations to the lognormal sum distribution have been proposed and employed in literature. However, these approximation methods are not without their drawbacks. Some widely used approximation methods are not accurate at the …

A Low-Cost Acoustic Array For Detecting And Tracking Multiple Acoustic Targets, Ellen E. Case

Browse all Theses and Dissertations

A wide variety of real-world targets emit distinct acoustic signatures that not only distinguish them from one another but also provide spectral separation from background clutter. While acoustic signatures are distinct, they can also be highly variable, even for an individual target, making detection and tracking a challenging problem. This thesis presents a low-cost acoustic array using commercial off-the shelf (COTS) hardware to detect and track multiple small, moving, acoustic targets. It implements a cross-correlation method for calibration, delay-and-sum beamforming, CA-CFAR detection, a discrete Kalman filter for tracking, and nearest neighbor data association. In addition, the array is designed to …

An Algorithm For The Detection Of Handguns In Terahertz Images, Andrew J. Lingg

Browse all Theses and Dissertations

This paper presents an algorithm for detecting handguns in terahertz images. Terahertz radiation is capable of penetrating certain materials which are opaque atoptical wavelengths, such as clothing, without the harmful effects of ionizing radiation. The approach taken is to segment objects of interest and classify them based on shape. We use a modified version of an active contour algorithm found in the open literature. Modifications include: a pre-processing step that includes clutter filtering and seeding of an initial contour; and a post-processing step that removes clutter pixels from the segmentation. The features used for classification are moment-based and Fourier shape …

Implementation Of Null Conventional Logic In Cots Fpga's, Mohamad Rajgara

Browse all Theses and Dissertations

The digital world has been dominated by the growth of synchronous digital design techniques for last few decades. Traditional Boolean logic is symbolically incomplete since it has a separate control logic, time in the form of clock signal which be carefully integrated with the logic design, but with digital clock signal already in the GHz range, this integration is further complicated. One approach to address post GHz digital logic design is to use clockless or asynchronous digital design techniques. In the mid '90s Theaseus Logic Inc. proposed a method to design Asynchronous circuits using Null Convention Logic (NCL).This thesis introduces …

A Novel Expanded 16-Dimensional Constant Envelope Q2psk Constellation, Milton I. Quinteros, Kenneth V. Cartwright, Edit J. Kaminsky, Ricardo U. Gallegos

Electrical Engineering Faculty Publications

We introduce a 16-dimensional constant-amplitude constellation that is generated by concatenating either four constant envelope quadrature-quadrature phase shift keying (CEQ2PSK) symbols from Saha and Birdsall or four CEQ2PSK symbols recently discovered by Cartwright and also introduced here. Our new constellation doubles the number of points available for data transmission without decreasing the distance between points or increasing energy, and may therefore be used in a trellis coded modulation (TCM) system without constellation expansion penalty. Because the new constellation has constant envelope, the modulation scheme becomes very attractive for nonlinear channels such as the magnetic recording channel or the satellite channel …

Classification Of Cylindrical Targets Buried In Seafloor Sediments, Edit J. Kaminsky, Madalina Barbu

Electrical Engineering Faculty Publications

This paper presents the development and evaluation of a time-frequency processing technique for detection and classification of buried cylindrical targets from chirpbased parametric sonar data. The software is designed to discriminate between cylindrical targets —such as cables— of different diameters, which need to be identified as different from other strong reflectors or point targets. The method is evaluated on synthetic data generated with an acoustic scattering model for elastic cylinders for seven different diameters. The model generates characteristic responses of targets acquired by a parametric sonar system. The signal at the sonar receiver hydrophones is first windowed to reduce the …

Modeling And Analysis Of Split And Merge Production Systems, Yang Liu

University of Kentucky Master's Theses

Many production systems have split and merge operations to increase production capac- ity and variety, improve product quality, and implement product control and scheduling policies. This thesis presents analytical methods to model and analyze split and merge production systems with Bernoulli and exponential reliability machines under circulate, priority and percentage policies. The recursive procedures for performance analysis are de- rived, and the convergence of the procedures and uniqueness of the solutions, along with the structural properties, are proved analytically, and the accuracy of the estimation is justi¯ed numerically with high precision. In addition, comparisons among the e®ects of di®erent policies …

Stranded Core Transformer Loss Analysis, Xingxing Zhang

University of Kentucky Master's Theses

We will present the approaches used to investigating the power loss for the stranded core transformers. One advantage of using stranded core is to reduce power loss or enhance transformer efficiency. One difficulty in the modeling of this type of transformer is that the core is not solid (there are small gaps between core wires due to circular cross section). A two dimensional finite element method with nodal basis function for magnetostatic field was developed to study the effects of the small gaps between core wires. The magnetic flux densities are compared for the uniform (solid) cores and the stranded …

Hdl Implementation And Analysis Of A Residual Register For A Floating-Point Arithmetic Unit, Akil Kaveti

University of Kentucky Master's Theses

Processors used in lower-end scientific applications like graphic cards and video game consoles have IEEE single precision floating-point hardware [23]. Double precision offers higher precision at higher implementation cost and lower performance. The need for high precision computations in these applications is not enough to justify the use double precision hardware and the extra hardware complexity needed [23]. Native-pair arithmetic offers an interesting and feasible solution to this problem. This technique invented by T. J. Dekker uses single-length floating-point numbers to represent higher precision floating-point numbers [3]. Native-pair arithmetic has been proposed by Dr. William R. Dieter and Dr. Henry …

Super Resolution 3d Scanning Using Spatial Light Modulator And Band Correction, Akshay Pethe

University of Kentucky Master's Theses

Multi Frequency Phase Measuring Profilometry is the most popular lateral contact 3-D Scanning technique. The Phase Measuring Profilometry is limited in resolution by the projector and cameras used. Conventional signal projectors have a maximum of 2000 to 4000 scan lines limiting the projector resolution. To obtain greater detail with higher resolution the PMP technique is applied to a Spatial Light Modulator (SLM) having 12000 lines, very large as compared to conventional projectors. This technology can achieve super resolution scans having varied applications. Scans achieved from PMP suffer from a certain type of artifact called “banding” which are periodic bands across …

Role Of Dipoles In The Bulk Phosphor Layer In The Electroluminance Mechanisms Of A.C. Thin Film Electroluminescent Display Devices, Praveen Kumar Sivakumar

University of Kentucky Doctoral Dissertations

The purpose of this dissertation is to advance the understanding of SrS-based a. c. thin film electroluminescent (ACTFEL) devices. The role of traps in the bulk phosphor layer in the light emission mechanism from ACTFEL devices is studied, characterized and modeled.

Experiments were performed to observe the response of the ACTFEL devices to tailored voltage excitations. A physical model was developed to describe the optoelectronic processes taking place in the phosphor; analytical equations were written and numerically simulated to plot the flux and luminance responses of the device to similarly tailored voltage excitations.

The voltage excitation parameters such as amplitude, …

Thevenin Equivalent Circuit Estimation And Application For Power System Monitoring And Protection, Mohammad M. Iftakhar

University of Kentucky Master's Theses

The Estimation of Thevenin Equivalent Parameters is useful for System Monitoring and Protection. We studied a method for estimating the Thevenin equivalent circuits. We then studied two applications including voltage stability and fault location. A study of the concepts of Voltage Stability is done in the initial part of this thesis. A Six Bus Power System Model was simulated using MATLAB SIMULINK®. Subsequently, the Thevenin Parameters were calculated. The results were then used for two purposes, to calculate the Maximum Power that can be delivered and for Fault Location.

Nanostructured Thin Films And Tubes Of Titania For Room Temperature Sensing Of Gases, Satish Kumar Kandala

University of Kentucky Master's Theses

The main objective of this work was to study the applicability of Nano porous/Nanocrystalline TiO₂ films for serving the growing demand for fast accurate and low cost air quality analysis techniques. The sensitivity of response to variations in microstructure pointed the way to obtain controlled, reproducible and regular microstructures with critical dimensions proportionate with the Debye- length of the oxide. This work aimed to study the sensor properties of thin films of Nanocrystalline Titania and Titania nanotubes at room temperature. Nano porous/Nanocrystalline TiO₂ films were fabricated through evaporation driven convection/sol-gel method by controlling the process conditions. We also …

Synthesis And Characterization Of Schottky Diodes On N-Type Cdte Nanowires Embedded In Porous Alumina Templates, Srikanth Yanamanagandla

University of Kentucky Master's Theses

This work focuses on the growth of vertically aligned CdTe nanowire arrays of controllable diameter and length using cathodic electro deposition in anodized alumina templates. This step was followed by annealing at 250° C in a reducing environment (95% Ar + 5% H2). AAO template over ITO-glass was used as starting template for the device fabrication. The deposited nanowires showed nanocrystalline cubic phase structures with a strong preference in [111] direction. First gold (Au) was deposited into AAO using cathodic electro deposition. This was followed by CdTe deposition into the pore. Gold was deposited first as it aids the growth …

Ex-Situ And In-Situ Selenization Of Copper-Indium And Copper-Boron Thin Films, Rodney J. Soukup, Natale J. Ianno, Chad Kamler, Martin Diaz, Shuchi Sharma, James Huguenin-Love, Jiri Olejnicek

Department of Electrical and Computer Engineering: Faculty Publications

It has recently been established that the ideal bandgap for terrestrial photovoltaics is 1.37 eV and the bandgap for CulnSe2 is only around 1.04 eV. Thus, a larger bandgap is needed. However, neither the substitution of Ga nor of AI has made a high efficiency solar cell absorber with a band gap of 1.37 eV possible. B, an even smaller atom, should require less atomic substitution than either Ga or AI to achieve a wider bandgap. In order to fabricate a thin film of Culn_xB_1-xSe₂ (CIBS), Cu, In and B were deposited from a variety …

Grid Connection Requirements And Solutions For Dfig Wind Turbines, Wei Qiao, Ronald G. Harley

Department of Electrical and Computer Engineering: Faculty Publications

As the number and size of windfarms continue to grow,many countries have established or are developing a set of specific requirements (i.e., grid codes) for operation and grid connection of windfarms. The objective of these grid codes is to ensure that wind farms do not adversely affect the power system operation with respect to security of supply, reliability and power quality. This paper reviews major grid code requirements for wind farms, and investigates various technologies developed by and solutions proposed by researchers and wind turbine manufactures in order to meet these requirements. In addition, some ofthe authors' work on these …

Reliability-Based Stand-Alone Photovoltaic System Sizing Design- A Case Study, Haifeng Ge, Liqin Ni, Sohrab Asgarpoor

Department of Electrical and Computer Engineering: Faculty Publications

This paper introduces a method for designing a standalone photovoltaic system to improve the load point reliability, extend the operation life, and minimize the design cost. This approach examines the impacts of solar panel sizes, tilt angles and battery volumes toward load point reliability, as well as the expected system life, by using real insolation data in a given location and random load burdens. The reliability evaluation incorporating solar insolation variations and load point uncertainty is performed. Life evaluation of battery is included in this paper with consideration of the battery State of Charge (SoC) history. The Economical analysis to …

A Quantitative Study Of Mobility Impact For Real- Time Services On A Wi-Fi Multi-Hop Network, Ting Zhou, Hamid Sharif, Michael Hempel, Puttipong Mahasukhon, Wei Wang, Song Ci

Department of Electrical and Computer Engineering: Faculty Publications

In this paper, we analyze the performance of mobile real time services in a large-scale IEEE 802.11 multi-hop network. We present our field measurements with discussion of performance bottlenecks for VoIP services under mobile scenarios. We utilized our test bed which is located in Nebraska and supported by the University of Nebraska-Lincoln (UNL), US Federal Railroads Administrations (FRA), and major US railroad companies. Our UNL-FRA test bed consists of 8 outdoor access point towers, which are deployed along 3.5 mile of BNSF railroad. Passive measurement approaches are taken to ensure the integrity of collected data and multi-layer stream based packet …

Full-Wave Finite-Difference Time-Domain Simulation Of Electromagnetic Cloaking Structures, Yan Zhao, Christos Argyropoulos, Yang Hao

Department of Electrical and Computer Engineering: Faculty Publications

This paper proposes a radial dependent dispersive finitedifference time-domain method for the modeling of electromagnetic cloaking structures. The permittivity and permeability of the cloak are mapped to the Drude dispersion model and taken into account in dispersive FDTD simulations. Numerical simulations demonstrate that under ideal conditions, objects placed inside the cloak are ‘invisible’ to external electromagnetic fields. However for the simplified cloak based on linear transformations, the back scattering has a similar level to the case of a PEC cylinder without any cloak, rendering the object still being ‘visible’. It is also demonstrated numerically that the simplified cloak based on …

Gene Expression Analysis Of Embryonic Stem Cells Expressing Ve-Cadherin (Cd144) During Endothelial Differentiation, Vesna Nikolova-Krstevski, Manoj Bhasin, Hasan H. Otu, Towia A. Libermann, Peter Oettgen

Department of Electrical and Computer Engineering: Faculty Publications

Background: Endothelial differentiation occurs during normal vascular development in the developing embryo. This process is recapitulated in the adult when endothelial progenitor cells are generated in the bone marrow and can contribute to vascular repair or angiogenesis at sites of vascular injury or ischemia. The molecular mechanisms of endothelial differentiation remain incompletely understood. Novel approaches are needed to identify the factors that regulate endothelial differentiation.

Methods: Mouse embryonic stem (ES) cells were used to further define the molecular mechanisms of endothelial differentiation. By flow cytometry a population of VEGF-R2 positive cells was identified as early as 2.5 days after differentiation …

Aspects Of Producing, Directing, Conditioning, Impinging And Detecting Spectroscopic Electromagnetic Radiation From Small Spots On Samples, Martin M. Liphardt, Ping He, Blaine D. Johs, Galen L. Pfeiffers, James D. Welch, John A. Woollam

Department of Electrical and Computer Engineering: Faculty Publications

Sytems and mehtods for providing and enhancing electromagnetic radiation beam radail energy homogeneity and intensity vs. wavelength content, for reliably directing electromagnetic radiation emitted by a source thereof in a common direction, for achromatically reducing spot size on a sample (eg. liquid cavity containing lenses and low aberration 1:1 imaging systems modified to perform as spatial filters), and for directing directing different wavelengths into different detectors, in ellipsometer, polarizer or the like systems.

System And Method Ofselectively Monitoring Sample Front And Backside Reflections In Ellipsometer And The Like Systems, James D. Welch, John A. Woollam, Martin M Liphardt

Department of Electrical and Computer Engineering: Faculty Publications

A spectrophotometer, reflectometer, ellipsometer polarimeter or the like system having a detector means for independently intercepting electromagnetic radiation reflected from a sample frontside or backside, and methodology for pursuing less correlated determination of refractive index and thickness values.

Average Min-Sum Decoding Of Ldpc Codes, Nathan Axvig, Deanna Dreher, Katherine Morrison, Eric T. Psota, Lance C. Pérez, Judy L. Walker

Department of Mathematics: Faculty Publications

Simulations have shown that the outputs of minsum (MS) decoding generally behave in one of two ways: the output either eventually stabilizes at a codeword or eventually cycles through a finite set of vectors that may include both codewords and non-codewords. This inconsistency in MS across iterations has significantly contributed to the difficulty in studying the performance of this decoder. To overcome this problem, a new decoder, average min-sum (AMS), is proposed; this decoder outputs the average of the min-sum output vectors over a finite set of iterations. Simulations comparing MS, AMS, linear programming (LP) decoding, and maximum likelihood (ML) …

Development Of Fiber Bend Loss Edge Filter, Pengfei Wang

Doctoral

This PhD thesis addresses several aspects of macrobending loss in single-mode optical fibers. The context for the work is the development of an edge filter for a rapid wavelength measurement system. Based on scalar approximation theory and the beam propagation method, a simulation platform is developed and used to predict the macrobending loss of singlemode fiber with single or multiple coating layers. A single-mode step index fiber macrobending loss edge filter is investigated theoretically in terms of baseline loss, discrimination range and polarization dependent loss (PDL). The theoretical analysis is supported by a range of experimental investigations and results. The …

A Macro-Bend Fiber Based Wavelength Demodulation System For Optical Fiber Sensing Applications, Ginu Rajan

Doctoral

This thesis considers the design and development of a wide range allfiber interrogation system with a rapid measurement capability for extracting reliable measurand information from fiber Bragg grating sensors. Existing passive and active interrogation systems have certain limitations and do not satisfy all requirements. In this thesis a wavelength demodulation system is proposed, based on a macro-bend fiber filter employed in a ratiometric detection scheme. A theoretical model and analysis of an edge filter based ratiometric wavelength measurement (RWM) system is presented. A fiber edge filter is realized by carefully selecting an appropriate bend radius and number of bend turns …