Electrical and Computer Engineering Commons^™

Power Bus Isolation Using Power Islands In Printed Circuit Boards, J. Chen, Todd H. Hubing, Richard E. Dubroff, Thomas Van Doren

Electrical and Computer Engineering Faculty Research & Creative Works

Power islands are often employed in printed circuit board (PCB) designs to alleviate the problem of power bus noise coupling between circuits. Good isolation can be obtained over a wide frequency band due to the large series impedance provided by the gap between the power islands. However, power bus resonances may degrade the isolation at high frequencies. The amount of isolation also depends on the type of connection between power islands and the components on the board. This paper experimentally investigates the effectiveness of several power island structures up to 3.0 GHz

Boundary Effects On Multiplication Noise In Thin Heterostructure Avalanche Photodiodes: Theory And Experiment [Al/Sub 0.6/Ga/Sub 0.4/As/Gaas], Majeed M. Hayat, Oh-Hyun Kwon, Shuling Wang, Joe C. Campbell, Bahaa E.A. Saleh, Malvin Carl Teich

Electrical and Computer Engineering Faculty Research and Publications

The history-dependent recurrence theory for multiplication noise in avalanche photodiodes (APDs), developed by Hayat et al., is generalized to include inter-layer boundary effects in heterostructure APDs with multilayer multiplication regions. These boundary effects include the initial energy of injected carriers as well as bandgap-transition effects within a multilayer multiplication region. It is shown that the excess noise factor can be significantly reduced if the avalanche process is initiated with an energetic carrier, in which case the initial energy serves to reduce the initial dead space associated with the injected carrier. An excess noise factor reduction up to 40% below the …

Design And Analysis Of Class Ab Rf Power Amplifier For Wireless Communication Applications, Mohamed El-Dakroury

Retrospective Theses and Dissertations

The Power Amplifier is the most power-consulting block among the building blocks of RF transceivers. It is still a difficult problem to design power amplifiers, especially for linear, low voltage operation. Until now power amplifiers for wireless applications is being produced almost in GaAs processes with some exceptions in LDMOS, Si BJT, and SiGe HBT. The submicron CMOS processes for power amplifiers are under research focus since CMOS offers integration for power amplifier with rest of the transceivers blocks due to its high yield. Also CMOS process is cheap.

This thesis report details the design process of a class AB …

High Frequency Communication System Modeling And Performance Enhancement, Employing Novel Adaptive Dsp Techniques, Murad M. Qahwash

Retrospective Theses and Dissertations

High Frequency (HF) communication has been shown to be a useful communication technique from the very beginning of World War I and it accelerated during World War II. This is attributed to its simplicity, ability to provide near globe connectivity at low power without repeaters, moderate cost, and ease of proliferation [1]. In fact, the HF communication system utilizes the ionosphere [2][3][4] to refract the skywave signals to a distant receiver. This ionospheric channel has some disadvantages. First, it is a non-stationary channel as the HF frequency propagation is a function of the sun spot activities, solar winds, and diurnal …

A Hybrid System Theoretic Approach For Admission Controller Design In Multimedia Networks, Sarangapani Jagannathan

Electrical and Computer Engineering Faculty Research & Creative Works

A novel real-time discrete-event admission control (AC) scheme for high-speed networks is proposed with the aim of attaining a desired quality of service (QoS) and high network utilization. The AC uses the available capacity from a novel adaptive bandwidth estimation scheme, a congestion indicator derived from a congestion controller, peak bit/cell rate (PBR/PCR) estimate from new sources, along with the desired QoS metrics, and makes decisions whether to 'admit' or 'reject' new sources. The novel aspect of the proposed approach is the application of hybrid system theory to prove the performance of the admission controller, stability and the development of …

Decoupling Strategies For Printed Circuit Boards Without Power Planes, Todd H. Hubing, Hwan-Woo Shim, Theodore M. Zeeff

Electrical and Computer Engineering Faculty Research & Creative Works

Traditional decoupling capacitors connected between V/CC/ and GND traces can be relatively ineffective at frequencies above their self-resonant frequency. This paper evaluates decoupling capacitor mounting strategies on boards without power planes. Techniques for minimizing mutual inductance and improving decoupling at frequencies above resonance are investigated.

Adaptive Radio Resource Management For 2.5g Cellular Networks, Ken Murray

Theses

Recent years have seen a dramatic increase in demand for mobile communication services and with the introduction of 2.5G services such as general packet radio service, this trend is expected to increase further. These new services will introduce highly dynamic tele-traffic variations due to the inherent variability in resource usage of the new data services. The net effect will be considerable increase in load on the available radio resources. The currently employed fixed channel allocation scheme lacks the flexibility to support such traffic variations. A plethora of dynamic channel allocation schemes have been proposed in the past in an effort …

Whispering-Gallery Modes In Shielded Hemispherical Dielectric Resonators, Sergey Kharkovsky, Z. E. Eremenko, V. V. Kutuzov, A. E. Kogut, Yuri F. Filipov

Electrical and Computer Engineering Faculty Research & Creative Works

The results of the numerical and experimental investigations of whispering-gallery (WG) modes in shielded hemispherical dielectric resonators are presented in this paper. It is shown that the Q factor of WG modes in the shielded resonator can be ten times much higher than the Q factor of the similar open hemispherical dielectric-resonator modes. Shielding the resonator can decrease the dimensions of both the dielectric hemisphere and resonator as a whole, saving the high-Q factor of WG modes. The usage of a cylindrical shield and local flat reflectors in the experiment provides the investigation of the high-Q factor of WG modes …

Full Binary Combination Schema For Floating Voltage Source Multilevel Inverters, Xiaomin Kou, Keith Corzine, Yakov L. Familiant

Electrical and Computer Engineering Faculty Research & Creative Works

This paper presents schema of operation for floating voltage source multilevel inverters. The primary advantage of the proposed schema is that the number of voltage levels (and thus power quality) can be increased for a given number of semiconductor devices when compared to the conventional "flying capacitor" topology. However, the new schema requires fixed floating sources instead of capacitors and therefore is more suitable for battery power applications such as electric vehicles, flexible AC transmission systems and submarine propulsion. Alternatively transformer/rectifier circuits may be used to supply the floating sources in a similar way to cascaded H-bridge inverters. Computer simulation …

Mobile Home Security With Gprs, Duy Nguyen

Theses : Honours

This thesis presents the results of an honours project on the development of a security system for use on mobile devices. Mobile Home Security (MHS) is a prototype system that aimed to fully investigate a potential use of the wireless high-speed technology General Packet Radio Service (GPRS) in transmitting video from a static location. This thesis Mobile Home Security with GPRS describes in detail the design and developmental stages for the system. The research focused on the sending of video from a security capture device over a high speed radio network. The first stage of the research involved the design …

Modeling Of Electrofusion Coils For Performance Optimization, Steve Farmer, Robert A. Sims

Journal of the Arkansas Academy of Science

Modeling physical parameters provides a virtual design environment allowing the confirmation and optimization of electrofusion characteristics. Finite element incorporate physical parameters and their interactions along common boundaries defined within a model geometry. The electrofusion of polymeric piping is a widely accepted means of assembling piping systems with zero-leakage integrity. The key parameters in the fusion process are the coil resistance, the current passing through the coil and the time the current is applied. Modeling the coil and applying current to the model is accomplished using the MATLABpartial differential equations (PDE) toolbox. This paper presents the method of modeling and the …

Co-Polymers Of Furan With Pyrrole Or Thiophene: A Synthetic Study, Rose M. Mcconnell, Walter E. Godwin, Susan E. Baker, Kenya Powell, Martha Baskett, Amy Morara, Xiadong Ma

Journal of the Arkansas Academy of Science

The use of conductive polymers as a substitute for metallic conductors and semiconductors has attracted much attention in the literature. In particular, aromatic heterocyclic polymers constitute an important class since they possess chemical and electrical stability in both the oxidized (doped) and neutral (undoped) state. Doping a polymer allows one to vary its electrical, mechanical, optical, and thermal properties. The properties of these polymers are promising for their many technological uses such as antistatic coatings, solar cells, and electronic devises. Polyfuran is among the least common heterocyclic polymers. Polyfuran has been reported to be much less stable that either polypyrrole …

Evaluation Of A Compound Probability Model With Tower-Mounted Scatterometer Data, David G. Long, Benjamin E. Barrowes

Faculty Publications

Six months of data from the YSCAT94 experiment conducted at the CCIW WAVES research platform on Lake Ontario, Canada, are analyzed to evaluate a compound probability model. YSCAT was an ultrawideband small footprint (ap 1 m) microwave scatterometer that operated at frequencies of 2-18 GHz, incidence angles from 0° to 60°, both h-pol and v-pol, and which tracked the wind using simultaneous weather measurements. The probability distribution function of the measured instantaneous backscattered amplitude (p(a)) is compared to theoretical distributions developed from-the composite model and a simple wave spectrum. Model parameters of the resulting Rayleigh/generalized lognormal distribution probability density function …

Mechanism For Membrane Electroporation Irreversibility Under High-Intensity, Ultrashort Electrical Pulse Conditions, R. P. Joshi, K. H. Schoenbach

Bioelectrics Publications

An improved electroporation model is used to address membrane irreversibility under ultrashort electric pulse conditions. It is shown that membranes can survive a strong electric pulse and recover provided the pore distribution has a relatively large spread. If, however, the population consists predominantly of larger radii pores, then irreversibility can result. Physically, such a distribution could arise if pores at adjacent sites coalesce. The requirement of close proximity among the pore sites is more easily satisfied in smaller organelles than in outer cell membranes. Model predictions are in keeping with recent observations of cell damage to intracellular organelles (e.g., mitochondria), …

Reliability Of Programmable Input/Output Pins In The Presence Of Configuration Upsets, Paul S. Graham, Nathaniel Rollins, Michael J. Wirthlin, Michael P. Caffrey

Faculty Publications

Sponsorship: Los Alamos National Laboratories (LA-UR-02-3163). Field programmable gate arrays (FPGAs) are an attractive alternative for space-based remote sensing applications. However, SRAM-based FPGAs are sensitive to radiation induced single-event upsets within the configuration memory. Such configuration upsets may change the logic, routing, and operating modes of a user FPGA design. Upsets within the configuration of an I/O block are especially troublesome as they may impact the operation of other system components. This paper will evaluate the operation of the I/O block within the Xilinx Virtex FPGA in the presence of configuration memory upsets and introduce techniques for detecting and repairing …

Self-Assembly Of Spatially Separated Silicon Structures By Si Heteroepitaxy On Ni Disilicide, Elena A. Guliants, Chunhai Ji, Wayne A. Anderson

Electrical and Computer Engineering Faculty Publications

A nonlithographic approach to produce self-assembled spatially separated Si structures for nanoelectronic applications was developed, employing the metal-induced silicon growth. Densely packed Si whiskers, 500–800 nm thick and up to 2500 nm long, were obtained by magnetron sputtering of Si on a 25 nm thick Ni prelayer at 575 °C. The nucleation of the NiSi2 compound at the Ni–Si interface followed by the Si heteroepitaxy on the lattice-matched NiSi2 is suggested to be the driving force for the whisker formation.

Design And Analysis Of Radio Frequency Deployment Algorithms For Gsm, Mónica Pérez-Carbonell

Theses

Due to the growth of the subscriber base and the introduction of new services, mobile communications networks’ demand for wireless resources is increasing. This has resulted in an increasing need to change the frequency allocation of a network in order to adapt the cellular network to new frequency demands.

Currently, a planning tool generates a new frequency plan, which is. then deployed to cell sites. The deployment should ideally be carried out with minimum disruption to network operation, which makes this deployment process a critical undertaking as any errors during or after the deployment can leave the network with poor …

Robust Generalised Predictive Control - An Optimal Design For Uncertain Systems, Thomas O'Mahony

Theses

One of the more popular model predictive control approaches, of late, is the generalised predictive controller (GPC). It has received widespread dissemination in academia and numerous successful applications in industry testify to its usefulness. Its popularity partly stems from its superiority over its predecessors, its simplicity and its control acumen. However, since GPC is based on a mathematical model of the process, significant deterioration in performance or even closed-loop instability may arise due to the inevitable discrepancies that arise between the model and the true system. To ensure that the loop stability is not compromised and an adequate level of …

Servo Response And Modelling Issues In Generalised Predictive Control, Ben Griffin

Theses

One of the more popular control strategies, of late, is the Generalised Predictive Controller (GPC). It has received widespread dissemination in academia and numerous successful applications in industry testify to its usefulness. Its popularity partly stems from its superiority to its predecessors, e.g. the generalised minimum variance and pole-placement controllers, but also from the GPC ‘tuning knobs’, which have simple time-domain interpretations and extremely robust default settings. However, despite the widespread interest, there would appear to be some issues relating to the specification of the closed-loop serv^o response that have not been covered in any great detail in the GPC …

Design Of Low Phase Drift Cmos Frequency Synthesisers, Cyril Patrick Hervé Florent Lahuec

Theses

This thesis presents a methodology for the development of high performance video clock synthesisers that have high (2000) input to output clock multiplication ratios. The synthesisers are required to be compatible with standard CMOS technologies and they must exhibit very low drift between their input and output clocks.

The methodology used borrows techniques established for RF synthesisers in the GHz range. In the RF domain there are significant constraints on spectral spread and because of this there has been significant interest in phase noise generated by intrinsic device noise. Simple and accurate models were developed that help understand the up …

A Factorization Approach For Solving The Hamilton-Jacobi Equations In Nonlinear Optimal Control, Mohammad Dikko Aliyu

LSU Doctoral Dissertations

The Hamilton-Jacobi equation (HJE) arose early in the last century in the study of the calculus of variation, classical mechanics and Hamiltonian systems. Recently, there has been a renewed interest in HJEs arising in various analysis and synthesis problems in systems theory. The HJE despite providing a necessary and sufficient condition for an optimal control, is very difficult to solve for general nonlinear systems, and therefore its application remained limited to linear systems. Yet, the HJE has been studied extensively in the literature from diverse areas of science and engineering, varying from mathematical physics, to mechanics, control theory, and to …

High-Efficiency Solar Cells Based On Cu(Inal)Se[Sub 2] Thin Films, S. Marsillac, P. D. Paulson, M. W. Haimbodi, R. W. Birkmire, W. N. Shafarman

Electrical & Computer Engineering Faculty Publications

A Cu(InAl)Se₂solar cell with 16.9% efficiency is demonstrated using a Cu(InAl)Se₂thin film deposited by four-source elemental evaporation and a device structure of glass/Mo/Cu(InAl)Se₂/CdS/ZnO/indium tin oxide/(Ni/Algrid)/MgF₂. A key to high efficiency is improved adhesion between the Cu(InAl)Se₂ and the Mo back contact layer, provided by a 5-nm-thick Ga interlayer, which enabled the Cu(InAl)Se₂ to be deposited at a 530 °C substrate temperature. Film and device properties are compared to Cu(InGa)Se₂ with the same band gap of 1.16 eV. The solar cells have similar behavior, with performance limited by recombination through …

Discrete-Time Velocity-Based Multiple Model Networks, Ruiyao Gao, Seamus Mcloone, Eugene Dermot Coyle Professor

Conference papers

The velocity-based local model (LM) network is a novel modelling approach that overcomes the lack of interpretability associated with the conventional LM network technique. The global dynamics of the nonlinear network are directly related to the underlying sub-model dynamics. Thus, the velocity-based network is ideally suited to the development of local controller (LC) networks. Furthermore, the local models are continuous-time, velocity-based and linear, providing continuity with established linear theory. To date, research has focused on the continuous-time version of the velocity-based network. The application of digital computer is widely popular in the field of control and, therefore, this paper develops …

A Non-Linear Pid Controller For Cstr Using Local Model Networks, Ruiyao Gao, Aidan O'Dwyer, Eugene Dermot Coyle Professor

Conference papers

The basic PID controllers have difficulty in dealing with problems that appear in complex non-linear processes. This paper presents a practical non-linear PID controller that deals with these non-linear difficulties. It utilises a local model (LM) network, which combines a set of local models within an artificial neural network structure, to adaptively characterise the process non-linearity. Then a local controller network is formulated through a gating system deduced from the LMN to handle the non-linearity. A continuous stirred tank reaction (CSTR) case study illustrates the practicality of this method in the modelling and control of non-linear processes. PID controllers are …

Time Delay Estimation In Signal Processing Applications: An Overview, Aidan O'Dwyer

Conference papers

An extensive though scattered literature exists on the estimation of time delays in signal processing applications. However, it is possible to identify themes that are common to many of the available techniques. The intention of this paper is to provide a framework against which the literature may be viewed. In addition, original work on gradient based time delay estimation is described.

Towards An Expert System Approach For Pi Controller Design Of Delayed Processes, Michael Feeney, Aidan O'Dwyer

Conference papers

This paper will discuss the compensation of first order lag plus time delay (FOLPD) processes using PI controllers whose parameters are specified using appropriate tuning rules. The gain margin and phase margin of the compensated system, as the ratio of time delay to time constant of the process varies, are calculated for each tuning rule and an expert system is used to recommend a tuning rule for user defined requirements.

Regenerative Magnet Load Power Supply With Utility Friendly Operations, M. Sri Balaji, S. P. Das, Gopal Dubey, Malabika Basu

Conference papers

In the present paper, a utility friendly regenerative magnet load power supply has been proposed which can tolerate supply voltage dips and long duration sags or undervoltages and maintains unity input power factor under all operating conditions. The harmonics injected into the utility are much less and the total harmonic distortion (THD) complies with IEEE standards. Unity power factor at the input is maintained by using a synchronous link converter (SLC) as the front-end AC to DC converter with regenerative capability. The two-quadrant chopper in the second stage operates in a constant frequency current control mode and takes care of …

Development Of A Testbed For Design And Evaluation Of Power Electronic Based Systems, S. Pekarek, J. Tichenor, N. Benavides, A. Koenig, H. Wang, Scott D. Sudhoff, B. Kuhn, S. Glover, D. Aliprantis, J. Byoun, J. Sauer

Electrical and Computer Engineering Faculty Research & Creative Works

In this paper, a detailed technical description of a new hardware-based integrated power system testbed is presented. The testbed consists of an AC generation and propulsion system that is coupled to a DC zonal distribution system. A primary objective of the testbed is to provide a resource to the academic and industrial community by providing a non-proprietary system on which to demonstrate controls, survivability algorithms, and validate computer-aided design (CAD) tools. Copyright © 2002 Society of Automotive Engineers, Inc.

Stability Analysis Of A Dc Power Electronics Based Distribution System, Scott D. Sudhoff, Steven Pekarek, S. F. Glover, S. H. Zak, E. Zivi, J. D. Sauer, D. E. Delisle

Electrical and Computer Engineering Faculty Research & Creative Works

This paper illustrates the application of the generalized immittance space approach to the analysis of multi-bus interconnected power electronics-based power distribution system. The paper sets forth the basic classifications of power converters in regard to stability analysis, a set of network reduction transformations, and illustrates the use of these reductions in order to analyze the stability of a zonal dc distribution system. Copyright © 2002 Society of Automotive Engineers, Inc.

End To End Congestion Control In High-Speed Networks, Sarangapani Jagannathan

Electrical and Computer Engineering Faculty Research & Creative Works

This paper proposes an adaptive methodology to prevent congestion in packet switched networks such as the Internet, where the internal network nodes convey very little information to the ingress nodes. Two architectures of preventing the congestion are presented: the first one when the traffic arrival rates, and bottleneck queue levels are known and the other when these are unknown. In the latter, the network traffic is estimated online using an adaptive system by measuring the buffer occupancy. In both architectures, the congestion is controlled by adjusting the transmission rates of non real-time and certain real-time sources in response to the …