Electrical and Computer Engineering Commons^™

Artifact Filter., Kent William Swearingen

Masters Theses

"Peripheral blood pulse monitors are highly susceptible to noise-artifact-- in their present stage of development. The purpose of this thesis is to demonstrate a feasible means for filtering the artifact, using existing monitors. Since no peripheral pulse monitor (transducer) was available for experimentation, a simulated test input was devised with frequency variations from JO cycles/minute to 1.50 cycles/minute.

The filtering circuit predicts the time location of each input pulse. The location of the prediction is governed by the accuracy of the preceding prediction. This is controlled by an R-C timing circuit with a Schmitt Trigger and relay.

From the data …

Optimalization By Peak-Holding, Curtis W. Dodd

Masters Theses

"The problem presented is a study of the peak-holding method of optimalization. This method applies to a system that has an extremum.

After describing how the complete system, consisting of the controller and the controlled system, works; variations in the controller are presented. These variations are changes in the final stage of the controller, the servo. A phase-plane analysis shows how the output of the controlled system varies with its rate of change. Limitations are presented which tell why the system cannot be kept at its peak value at all times. Finally an analog simulation is used to study the …

Real Time Testing With A Time Scaled Analog Computer., Wayne F. Balsman

Masters Theses

"A present limitation to the testing of a physical subsystem within an analog simulation is that the analog computer must compute in real time. If it is necessary to time scale the simulation of the complete system, a physical subsystem of the complete subsystem may not be tested within the simulation. Therefore, a means of changing the time scale of the analog signal is needed to test a physical subsystem within a time scaled analog computer simulation.

In this thesis a means of time conversion by sampling the analog signal at one rate, storing the samples, and reading the samples …

A Time Optimum Bang Bang Control System Under Specified Inputs., John F. Curtin

Masters Theses

"The problem presented is a study, by simulation on an analog computer, of a time optimum "bang bang" control system with a second order plant. Phase plane analysis techniques are used to describe the performance of the second order plant under the action of a maximum effort controller. From this, the system logic is developed for time optimum response to a step reference input. A fast time model of the plant is used to obtain repeated high-speed extrapolations of the plant outputs, at the same time a linear predictor generates future values of the reference. The error functions thus found …

Missouri School Of Mines Antenna Range Design., Russell Melvin Ousley

Masters Theses

"The problem was to design, construct and evaluate an antenna range which could be used in future research and instructional programs. The basic theory of range design and practical considerations were studied and a range was then designed and built from equipment which was either immediately applicable, applicable after modification or constructed to fit the needs of the range. Tests were made to determine the performance characteristics of the system with respect to the more important design parameters. Suggestions were given for future improvement of operation and expansion of the range capabilities"--Abstract p. ii

Determining Stability Of Nonlinear Control Systems Via Lyapunov's Method., John Joseph Komo

Masters Theses

"The problem undertaken in this thesis is to present Lyapunov's method of stability as i t applies to control systems and to use it in the stability analysis of nonlinear control systems. The variable gradient method of generating Lyapunov functions is presented since this seems the best general procedure for obtaining Lyapunov functions. Also, the integration of matrices method is presented as a comparison. ii

Procedures for the use of the variable gradient method and the integration of matrices method are written and several examples are used to illustrate these procedures.

It is concluded that Lyapunov's method is very definitely …

Compensator Design For Unity Feedback Systems On The Digital Computer., Ping Liang

Masters Theses

"In control systems engineering it is frequently necessary to compensate a fixed plant whose transfer function cannot be changed. Usually the characteristics of the resulting system are established in terms of steady state and transient performance specifications. Generally it is necessary to insert a compensator which permits the system to satisfy the specifications as well as to provide an absolutely stable system.

In this thesis a method is developed to determine the transfer function of the compensator. Each system performance specification can be expressed in a differentiable inequality form composed of the system closed-loop gain, zeros, and poles. First, the …

Linear System Transfer Function Identification, Tuh-Kai Koo

Masters Theses

“An approach using a high speed special purpose digital computer to identify the transfer function of a linear system is presented in this thesis. The data for computation are obtained by measuring the system response and its derivatives periodically with a periodic test signal (impulse) input.

The order of the system is first determined by evaluating the rank of a Hankel matrix. Then, the transfer function is determined by solving two sets of system equations.

Theoretical analysis is emphasized in the study. Two examples are given for the purpose of illustrating the theory

Small Signal Gain Analysis For A Seven Cavity Klystron Amplifier., William E. Hord

Masters Theses

"The problem was to find a suitable method of using the digital computer to calculate the small signal gain characteristics of a seven cavity klystron amplifier. Background material relevant to the problem was reviewed. The differential equations for small signal conditions in a gridless gap klystron were developed. These equations were then solved and put in a matrix form suitable for digital computer analysis. Suggestions for additional development were proposed"--Abstract p. ii

Pattern Calculations On A Loaded Spiral Antenna., Jose Briceno

Masters Theses

"The purpose of this thesis is to calculate and p lot the radiation patterns o f a ferrotron-loaded spiral antenna made of semicircles. In particular, this work is confined to a balanced spiral free to radiate in all directions.

The current distribution used in the evaluation of the vector potential is taken from a synthesized current obtained from experimental information on a ferrotron-loaded spiral antenna at a frequency of operation of 200 MC.

The calculated patterns of the spiral antenna are in general single lobed in a direction perpendicular to the plane of the antenna. The beamwidth varies from 62° …

Infrared Modulation Using The Field-Effect Properties Of Germanium., Lloyd E. Brunkhorst

Masters Theses

"The absorption of infrared radiation, by free carriers in germanium, has been used to amplitude modulate infrared radiation. In the experiment, a space charge layer consisting of free carriers is established at the inner surface of a germanium sample by using the field-effect technique. Infrared radiation of a wavelength to which the germanium is transparent is then Internally reflected from this surface. The infrared radiation passes twice through the space charge layer for each internal reflection. With each pass through the space charge layer, the amplitude of the transmitted infrared is decreased. Amplitude modulation of the transmitted infrared is accomplished …

The Justification For And Design Of A Lunar Radio Observatory., Thomas Van Doren

Masters Theses

"The purpose of a radio telescope is to record information concerning the strength, spectrum, polarization, and direction of arrival of extraterrestrial electromagnetic radiation at radio frequencies. Earthly based radio observatories are hampered in their attempt to achieve this purpose by atmospheric absorption and reflection of the radiation. A lunar based system would not have this problem because the Moon possesses practically no atmosphere. However, other environmental conditions, such as micrometeorites, high frequency radiation, and extreme temperature variations, must be overcome. This thesis justifies the need for a lunar radio observatory and also describes a particular radio telescope system which should …

Digital Computer Design Of Compensation For Linear Control Systems, Larry C. Amsler

Masters Theses

"If a control system is to be synthesized, it is inferred that a plant or process is present which must be controlled, and the problem of how to design the control system then arises. The first step is to decide on performance specifications to which the complete system must conform. These specifications may involve such things as the system steady state response, transient response, or frequency response. Any of several synthesis methods may then be applied to complete the system design.

In this study a synthesis method is developed for single-loop linear feedback systems. First, the number of compensating poles …

Determining Design Freedom Of Linear Feedback Control Systems, Harley D. Brixey

Masters Theses

“The problem confronted in this thesis is to develop a method or procedure to be used in determining the amount of design freedom that is available in any given linear feedback control system by working with the signal flow-graph representation of the system.

Literature was reviewed that deals with basic signal flow-graph theory and degrees of design freedom. Signal- flow-graph theory that forms a foundation for the development is presented.

The development consists of starting with an essential signal-flow graph of order one. The sensitivity and transmittance functions are written for this essential graph in terms of graph symbols; then …

A Graphical Solution Method For The Tchebychev Elliptic Function Filter, Gene S. Luckfield

Masters Theses

"This thesis is concerned with the design of the Tchebychev elliptic function filter. The Darlington synthesis procedure is discussed and salient points from Darlington's paper needed for the design of this filter are presented.

It is shown that the design of the Tchebychev elliptic function filter requires a knowledge of the elliptic functions, particularly the elliptic sine. Since the use of these functions is not common, a brief review of their properties is presented.

Using the elliptic functions, a development of the equations describing the behavior of the Tchebychev elliptic function filter is given for the case of a normalized …

A Rc Active Delay Time Network., Robert Sun-Wu Han

Masters Theses

"This thesis presents a method for performing an approximate synthesis of a variable delay time network by using RC elements and active analog computer circuits. The delay networks discussed here can provide delay times which range from zero to 96 milliseconds for inputs with frequencies which range between zero 2nd 5 cycles per second.

Basically, the procedure involves approximating the delay time transfer function, e^-jwTd , by the ratio of two polynomials each of which is represented by a finite series of terms. The ratio is then shown to be easily synthesized by RC elements and analog computer circuits. …

Predicted Transient Response Of Complex Poles By Means Of A Residue Ratio, Rameshchandra Shankerbhai Patel

Masters Theses

"Transient response plays an important role in servomechanism, electronic and electrical circuits. A time response of a linear system is the intuitive and immediately comprehensible description of the system performance. The utility of the system performance in television and high speed computer circuits can be determined by its transient characteristics. By locating certain points on the transient response curve the designer is enabled to predict the shape of the response with some precision. The choice of the overall transfer function (or location of the system singularities on the s-plane plot) is decided by speed, accuracy and stability of the response …

A Tunnel Diode Parametric Down Converter, Leland Lovell Long

Masters Theses

"The problem, as presented, is to derive analytical expressions for the conversion gain, bandwidth, and noise figure of a self excited tunnel diode converter and to verify, if possible, the validity of these express- ions by building such a converter. These analytical results are presented and discussed. The converter circuit is shown along with the resulting intermediate frequency output. Gain and bandwidth measurements are also given. It is concluded that the self excited converter could very definitely be of value as a low noise pre-amplifying device in the ultra-high frequency and microwave frequency ranges"--Abstract, page ii.

A Study Of A Second-Order Predictive Control System, Tarkeshwar Singh

Masters Theses

"The purpose of this thesis is the study of a predictive control system by simulating it on an analog computer. Logic criteria for step reference inputs are derived by the phase- plane technique, and tie corresponding logic network designed to bring the error and error rate of the controlled system toward zero in the least possible time.

The responses of the predictive control system for step, ramp, sinusoidal and exponential reference inputs are investigated with primary emphasis placed on the rise time and overshoot for several values of step inputs of the reference.

Finally, recommendations are made for further investigations …

Linear Feedback Control System Compensator Design Under Specified Constraints, Keikhosrow Irani

Masters Theses

"The purpose of this thesis is to find the necessary and sufficient conditions for the design of compensators, following the concepts developed by Ross, Warren, Hsu and Sanden.

The main object that motivates this investigation is to design the lead or lag compensator networks for a given linear feedback system when there are these constraints.

1. Gain of the system is constant.
2. The steady-state error is invariant.
3. The dominant poles of the closed-loop transfer function are specified.

Consideration of the problem is in two parts:

• a. Derivation of necessary and sufficient conditions of compensator design that fulfill the three constraints.
• b. …

A Comparison Of A-C And D-C Lead Compensation From D-C Prototype Networks, Piyush Parikh

Masters Theses

"The object of this thesis is to study the difference in transient and frequency response characteristics between a prototype d-c phase lead compensating network and an equivalent a-c phase lead compensating network.

A second order servo is selected to be compensated and five d-c prototype and equivalent a-c phase lead compensating networks are designed. The frequency characteristics of the a-c networks are obtained experimentally and these of the d-c networks are obtained analytically. The characteristics of both networks are compared and their differences are studied. The transient characteristics of the d-c and a-c compensated closed-loop systems to a step input …

Design Of A Square Loop Magnetic Integrating Device, Fred Leland Grismore Jr.

Masters Theses

"The problem investigated in this research was the development of a static integrating circuit applicable to closed loop feedback control systems. Investigation of various methods of attack indicated that square loop magnetic cores offered characteristics required for the integration process. These include the ability to sum input information and the ability to store information for an indefinite period of time.

An experimental program was carried out, investigating the various properties of square loop magnetic materials and required design parameters. Through this work it was verified that the process of integration could be realized by using the partial switching volt-second absorption …

Scatter Matrix Analysis Of Plane Waves In A Layered Media, Bill W. Ashworth

Masters Theses

"The problem was the application of matrix theory to the solution of the reflection and transmission coefficients for a plane wave incident on a layered media. Background material relating to the problem was reviewed. Equations that were used in the solution of the problem were either derived or explained. The derivations for the reflection and transmission coefficients were carried out in order, starting with the simple case of normal incidence on a junction of two infinite media and progressing through the more difficult case of oblique incidence on a layer of finite thickness separating two infinite media. Scatter matrix analysis …

A Study Of Viscous Frictional Effects And Relay Characteristics On The Operation Of A Positional Relay Servomechanism, Earl F. Richards

Masters Theses

"The thesis describes some experimentally observed data and analytical approaches to the study of a relay servomechanism. The experimental data were secured from an analog simulation of a relay servo system. The results of this data were compared to the transient approach by use of the phase-plane method. The stability of the system was determined using a describing-function. The analytical approaches are described in the presentation.

A study of the effects of viscous friction is described, and the characteristic of the relay used in the system is given special attention. The response to input driving function was considered, and rise …

An Experimental Investigation Of Receiver System Sensitivity, James Henry Johnson

Masters Theses

"A method of determining the minimum detectable power density incident at the receiving antenna of a UHF receiver is proposed. The minimum detectable power density is the power density required to produce a signal-to-noise ratio of unity in the output of the receiver. The proposed method includes the receiving antenna impedance, the necessary connecting transmission lines, and the receiver impedance.

It is shown that an error in the antenna directivity will produce a significant error in the overall sensitivity of a receiving system. Since the directivity is the most difficult system variable to determine experimentally, it is probably the limiting …

Design Of An Intermediate Frequency Amplifier And Variable Frequency Oscillator, Robert Charles Mcintyre

Masters Theses

"Since the advent of the transistor in 1948 many technological barriers have been overcome in the field of semiconductors. Unfortunately, however, there is a considerable period of time between the discovery of a scientific phenomena and its widespread use and understanding by practicing engineers. The motivating factor which prompted this investigation was primarily the lack of knowledge which the author possessed concerning transistors. The selection of the amplifier and oscillator design confined the study primarily to the transistor. Considerable time, however, had to be spent in the study of basic transistor theory before any phase of the design could be …

Automatic Tuning Of A.C. Compensating Networks, Giles C. Sinkewiz

Masters Theses

"The purpose of this thesis is to illustrate the practicality of using an auxiliary servo system to shift parameters in damping networks of the main servo system.

Since amplification is most easily achieved with A.C. amplifiers and since A.C. servo motors are superior in operation to D.C. servo motors, because no brushes or commutators are needed, the A.C. servo system is widely used. However, one major problem is confronted when designing an A.C. servo system. This is the problem of designing damping circuits and compensating circuits which are insensitive to carrier frequency fluctuations. Notch filters provide the desired transfer functions, …

Analysis And Simulation Of A Cross-Correlation Communication System, Dennis Jay Gooding

Masters Theses

"Statement of the problem. The purpose of this study was (1) to calculate the probability of error as a function of receiver input signal-to-noise ratio for a typical communication system employing cross-correlation detection; (2) to design and construct an experimental model of such a communication system for the purposes of demonstrating the operation of the system and verifying the theoretical calculations"--Introduction, page 1.

The Equalization And Optimization Of A Third-Order Type-1 Position Control System, Viswanatha Seshadri

Masters Theses

"While the practice of feedback control dates back to the day when the earliest living organisms began to react to their environmental conditions and the changes therein, it has been only during the past two decades that this technique came to be subjected to a scientific examination. Yet, an astoundingly rapid advancement has resulted in the field of servo-mechanisms, contributing substantially to the development of modern civilized existence and activity to its present standards, and promising to contribute, to an ever-increasing extent, to the accelerated progress of scientific and industrial enterprise in this space age.

The principal concerns of the …

A Method For The Prediction Of Detection Ranges For Pulsed Doppler Radar, Phillip Orlan Brown

Masters Theses

"Modern radar systems must provide greater detection ranges both against high and low altitude targets because of the significant advances in weapon speed and range. Extended range indicates that the power transmitted by the radar must be increased. It follows, that ground return becomes a problem even at high altitudes.

There are at present three basic types of radars which are (1) pulsed, (2) continuous wave, and (3) pulsed doppler radar. The conventional pulsed radar now closely approaches the theoretical optimum performance; however, it does not have the inherent ability to distinguish between ground return and moving targets. The continuous …