Electrical and Computer Engineering Commons^™

Distributed Modeling Approach For Electrical And Thermal Analysis Of High-Frequency Transistors, Amirreza Ghadimi Avval

Graduate Theses and Dissertations

The research conducted in this dissertation is focused on developing modeling approaches for analyzing high-frequency transistors and present solutions for optimizing the device output power and gain. First, a literature review of different transistor types utilized in high-frequency regions is conducted and gallium nitride high electron mobility transistor is identified as the promising device for these bands. Different structural configurations and operating modes of these transistors are explained, and their applications are discussed. Equivalent circuit models and physics-based models are also introduced and their limitations for analyzing the small-signal and large-signal behavior of these devices are explained. Next, a model …

Reference Design Of An Online Emulation And Hot-Patching Approach For Power Electronic Controller Validation, Estefano Soria Pearson

Graduate Theses and Dissertations

This thesis aims to develop a reference design of an online security system approach embedded in a power electronic controller for cybersecurity purposes. Cybersecurity in power electronics focuses on reducing vulnerabilities in the system, where most reside in the communication with the hardware devices. Although methods to secure communications lessen the probability and effects of cyber-attacks, discovering vulnerabilities is inevitable. This thesis attempts to provide a fail-safe approach to securing the system by targeting the safety of the power-electronic controller. This approach applies an additional security layer in case of a malicious or accidental controller firmware malfunction.

The online security …

Investigation Of Membrane Based Processes For Biomedical Applications, Efecan Pakkaner

Graduate Theses and Dissertations

As substantial developments were achieved in nanotechnology and polymer engineering, especially in the last few decades, the use of membranes and membrane-based procedures was found to be expanding into more and more research and development areas; including biological engineering, life sciences and biomedical engineering. Not only have they been the main focus of meaningful research, but they have also been the main pieces of the solutions to very thorny problems encountered within a wide range of applications from microfluidics to water treatment, thanks to their versatility, cost-effectiveness and biocompatibility, when compared to conventional separation techniques. To celebrate and embrace these …

Experimental And Analysis Of Electromagnetic Characterization Of Biological And Non-Biological Materials In Microwave, Millimeter-Wave, And Terahertz Frequency Bands, Nagma Vohra

Graduate Theses and Dissertations

The goal of this research is to characterize the electromagnetic properties of biological and non-biological materials at terahertz (THz), millimeter-wave, and microwave frequency bands. The biological specimens are measured using the THz imaging and spectroscopy system, whereas the non-biological materials are measured using the microwave and millimeter-wave free-space system. These facilities are located in the Engineering Research Center at the University of Arkansas. The THz imaging system (TPS 3000) uses a Ti-Sapphire laser directed on the photoconductive antennas to generate a THz time domain pulse. Upon using the Fourier Transform, the spectrum of the pulsed THz signal includes frequencies from …

Direct Torque Control For Silicon Carbide Motor Drives, Mohammad Hazzaz Mahmud

Graduate Theses and Dissertations

Direct torque control (DTC) is an extensively used control method for motor drives due to its unique advantages, e.g., the fast dynamic response and the robustness against motor parameters variations, uncertainties, and external disturbances. Using higher switching frequency is generally required by DTC to reduce the torque ripples and decrease stator current total harmonic distortion (THD), which however can lower the drive efficiency. Through the use of the emerging silicon carbide (SiC) devices, which have lower switching losses compared to their silicon counterparts, it is feasible to achieve high efficiency and low torque ripple simultaneously for DTC drives.

To overcome …

Use Of The Igbt Module In The Active Region To Design A High Current Active Filter, Jorge F. Galarraga

Graduate Theses and Dissertations

Particle accelerators require high-precision magnetic fields on the order or 100ppm or less. This implies that the precision of the associated electrical current in the electromagnet that generates these fields should be smaller than 100ppm. However, conventional switching power supplies cannot offer this precision due to the frequency limitation of the switches. This research considers the use of power electronics devices operating in a linear as an alternative solution to meet the requirements of particle accelerator electromagnets.

This thesis presents the study of an insulated-gate bipolar transistor (IGBT) driver using a new control method that linearizes the IGBT’s collector-emitter voltage …

Efficiently Estimating Survival Signature And Two-Terminal Reliability Of Heterogeneous Networks Through Multi-Objective Optimization, Daniel Bruno Lopes Da Silva

Graduate Theses and Dissertations

The two-terminal reliability problem is a classical reliability problem with applications in wired and wireless communication networks, electronic circuit design, computer networks, and electrical power distribution, among other systems. However, the two-terminal reliability problem is among the hardest combinatorial problems and is intractable for large, complex networks. Several exact methods to solve the two-terminal reliability problem have been proposed since the 1960s, but they have exponential time complexity in general. Hence, practical studies involving large network-type systems resort to approximation methods to estimate the system's reliability. One attractive approach for quantifying the reliability of complex systems is to use signatures, …

Design And Validation Of A High-Power, High Density All Silicon Carbide Three-Level Inverter, Zhongjing Wang

Graduate Theses and Dissertations

Transportation electrification is clearly the road toward the future. Compared to internal combustion engine, the electrified vehicle has less carbon-dioxide emission, less maintenance costs and less operation costs. It also offers higher efficiency and safety margin. More importantly, it relieves human’s dependence on conventional fossil energy. In the electrification progress, the revolution of electric traction drive systems is one of the most important milestone. The traction system should keep high efficiency to avoid performance reduction. Moreover, the motor drive should be designed within limited space without sacrificing output power rating. Based on the road map from US Drive Electrical and …

Grid Strength Assessment Trough Q-V Modal Analysis And Maximum Loadability Of A Wind-Dominated Power System Using P-Q Regions, Pierre Obed Dorile

Graduate Theses and Dissertations

Climate change is a menace to the existence of the world and policymakers are trying totackle this phenomenon by deploying large-scale wind farms into their grids. Among them, wind energy shows a promising future to substitute the traditional power plants. However, the deployment of these wind farms into the grid is not a panacea that does not pose any challenges to the grid operators. Keeping the power system voltage stable while considering the strength of the transmission grid is among the major challenges facing by the transmission system operators. Amid normal operation and fault conditions, wind farms should help the …

Fabrication And Characterization Of Photodetector Devices Based On Nanostructured Materials: Graphene And Colloidal Nanocrystals, Wafaa Gebril

Graduate Theses and Dissertations

Photodetectors are devices that capture light signals and convert them into electrical signals. High performance photodetectors are in demand in a variety of applications, such as optical communication, security, and environmental monitoring. Among many appealing nanomaterials for novel photodetection devices, graphene and semiconductor colloidal nanocrystals are promising candidates because of their desirable and unique properties compared to conventional materials.

Photodetector devices based on different types of nanostructured materials including graphene and colloidal nanocrystals were investigated. First, graphene layers were mechanically exfoliated and characterized for device fabrication. Self-powered few layers graphene phototransistors were studied. At zero drain voltage bias and room …

Electrochemical Deposition In Energy Storage Devices, Witness Atutala Martin

Graduate Theses and Dissertations

Metals, whether in a solid or soluble ion form, are a vital part of any electrochemical storage system. More so, Li metal is widely considered as the ideal anode because of its low density and low electrochemical potential (-3.04 V vs. the standard hydrogen electrode – SHE). However, just like most metals, it does not plate or strip evenly during cycling which can lead to cycling performance issues, short cycling lifespans, and even safety concerns brought about by dendrites that can cause internal short-circuiting within cells. This research focused on investigating the electroplating of metals in both aqueous and non-aqueous …

Monte-Carlo-Based Analysis Of Traffic Flow For Urban Air Mobility Vehicles, Sara Ghayouraneh

Graduate Theses and Dissertations

The research conducted in this dissertation is focused on developing a simulation tool that can predict the traffic flow patterns of the Urban Air Mobility vehicles to alleviate some of the challenges related to their traffic management. First, an introduction to the concept of Urban Air Mobility is given, the usage of Automatic Dependent Surveillance-Broadcast systems for Urban Air Mobility vehicles is suggested and dynamic addressing concept is introduced as an answer to a part of air traffic management and address scarcity challenge for Urban air Mobility vehicles. Next, in order to simulate the traffic flow patterns of the Urban …

Computational Modeling Of Black Phosphorus Terahertz Photoconductive Antennas Using Comsol Multiphysics With Experimental Comparison Against A Commercial Lt-Gaas Emitter, Jose Isaac Santos Batista

Graduate Theses and Dissertations

This thesis presents computational models of terahertz (THz) photoconductive antenna (PCA) emitter using COMSOL Multiphysics commercial package. A comparison of the computer simulated radiated THz signal against that of an experimentally measured signal of commercial reference LT-GaAs emitter is presented. The two-dimensional model (2D) aimed at calculating the photoconductivity of a black phosphorus (BP) PCA at two laser wavelengths of 780 nm and 1560 nm. The 2D model was applied to the BP PCA emitter and the LT-GaAs devices to compare their simulated performance in terms of the photocurrent and radiated THz signal pulse. The results showed better performance of …

Understanding Diffusion And Electrochemical Reduction Of Li+ Ions In Liquid Lithium Metal Batteries, Witness Martin, Yang Tian, Jie Xiao

Chemistry & Biochemistry Faculty Publications and Presentations

Lithium metal has drawn significant interest as an anode material for next generation lithium (Li) batteries. However, due to its propensity to form dendrites in commonly used electrolytes during repeated cycling, it has not yet been commercialized in secondary batteries. The formation of a Li protrusion is determined by the relative speed of Li+ ions being reduced and how fast they can be replenished in the vincinity of electrode. However, it is very difficult to quantify such kinetic parameters of Li+ ion in different electrolytes, not mentioning the identification of the desired electrolyte recipe to mitigate Li dendrite formation. Herein, …

Malicious Hardware & Its Effects On Industry, Gustavo Perez

Computer Science and Computer Engineering Undergraduate Honors Theses

In recent years advancements have been made in computer hardware security to circumnavigate the threat of malicious hardware. Threats come in several forms during the development and overall life cycle of computer hardware and I aim to highlight those key points. I will illustrate the various ways in which attackers exploit flaws in a chip design, or how malicious parties take advantage of the many steps required to design and fabricate hardware. Due to these exploits, the industry and consumers have suffered damages in the form of financial loss, physical harm, breaches of personal data, and a multitude of other …

Evaluating The Thermal Conductivity Of Potting Materials Using The Hot-Wire Method, Yeny Hau Chen

Electrical Engineering Undergraduate Honors Theses

This thesis is focused on the evaluation of the thermal conductivity of certain potting materials, in particular Aluminum Nitride (AlN), thermal putty, and silicone oil using the “hot-wire” method in order to allow volume reductions of inductors, and thus, increase the power density of converters. The main objective of this thesis is then to study the behavior of these specific materials intended for high-density power converters by mixing them with different proportions and placing the resulting compounds into a can for calculating their thermal conductivities, in order to evaluate the effects on the power density of inductor-based converters. One objective …

Design And Fabrication Of A Microstrip Bandpass Filter In Ltcc, Allison Rucker

Electrical Engineering Undergraduate Honors Theses

The goal of the project was to design and fabricate a bandpass filter with a center frequency of 25GHz with a 2GHz bandwidth. The first step was to do the calculation to design a bandpass filter to meet these specifications along with the properties of the Dupont^TM GreenTape^TM 9K7. HFSS was then used to verify the results from the initial calculations. There was a significant error between the two results, so more tweaking was done to the calculations to get a better center frequency. After a final design was decided, the fabrication process started. Low-Temperature Co-Fired Ceramics (LLTC) …

Data Forgery Detection In Automatic Generation Control: Exploration Of Automated Parameter Generation And Low-Rate Attacks, Yatish R. Dubasi

Computer Science and Computer Engineering Undergraduate Honors Theses

Automatic Generation Control (AGC) is a key control system utilized in electric power systems. AGC uses frequency and tie-line power flow measurements to determine the Area Control Error (ACE). ACE is then used by the AGC to adjust power generation and maintain an acceptable power system frequency. Attackers might inject false frequency and/or tie-line power flow measurements to mislead AGC into falsely adjusting power generation, which can harm power system operations. Various data forgery detection models are studied in this thesis. First, to make the use of predictive detection models easier for users, we propose a method for automated generation …

Transimpedance Amplification Of Optocoupler Output For High Temperature Applications, Kara Maurer

Electrical Engineering Undergraduate Honors Theses

When looking to the future of electronics, one characteristic is becoming more lucrative: high temperature capabilities. With the goals of not only becoming more efficient electronically, spatially, and cost-wise, adapting electronics for a high temperature environment can potentially be a route to all three of these goals. Not only does it take away the need for a cooling method, but it can also increase the longevity of a product which can make it even more cost effective. In an effort to contribute to the push for high temperature electronics, the University of Arkansas is developing a high temperature power module …

Optoelectronic Valley-Spin Qubits With Ambipolar Quantum Dots, Jeremy Tull

Electrical Engineering Undergraduate Honors Theses

The current limitations of qubit-based processors are caused by imperfections in quantum gates, leading to a lack of gate fidelity. Gate fidelity can be refined by extending the coherence of qubits and reducing logic operation speed. A potential solution is to develop a hybrid qubit that has the coherence of electrically-controlled quantum dots and the gate speed of their optically-controlled counterparts. Quantum bits that utilize ultrafast optical gating to perform gate operations require precise control of the gating pulse duration. Optical dispersion can cause adverse effects pulse duration, such as pulse broadening, so dispersion-compensation techniques must be employed; by properly …

Ironless, Axial Flux, Electric Bldc Motor For Aircraft Electric Propulsion, Kevin W. Hobbs

Electrical Engineering Undergraduate Honors Theses

3D printing has shown much promise as a method of rapidly manufacturing lightweight ironless motors to meet the growing demand that airlines have for more cost-effective products that reduce emissions and flight prices. 3D-printed ironless, axial flux, electric BLDC motors would meet these needs with both their high efficiency and power density.

A Halbach array motor was designed and 3D-printed for the analysis of its magnetic properties to gain more insight about it performance. Fusion 360 was used to design the 3D drawings of the motor parts. The rotor, stator, and stator mount were designed to accommodate the sizes of …

An Examination Of Grid Stability As It Relates To The Increased Integration Of Inverter-Based Resources, Daniel Voss

Electrical Engineering Undergraduate Honors Theses

There is currently a growing interest in increasing the amount of renewable energy resources connected to the bulk electric system (BES) that stems from various environmental, political, and social concerns. However, the differences between conventional generation resources and inverter-based resources (IBR)—namely wind and solar—pose new issues that make this increased integration a larger problem. In other studies, the increased penetration of renewable energy resources has resulted in weak-grid systems that are more susceptible to collapse. This comes as a result from the inability for IBRs to effectively provide enough reactive power, an effect especially apparent during fault conditions, which the …

Effect Of Silicon Carbide On Electric Drivetrains Of Heavy-Duty Vehicles, Haley Solera

Electrical Engineering Undergraduate Honors Theses

The application of electro-mechanical motors in rigorous, high-temperature systems is constantly adapting to suit the growing needs of developers in the automotive, construction, and aerospace industries. With improved efficiency, torque, and environmental impact over conventional internal combustion engines, electric drive trains pose more than ample incentive for manufacturers to invest considerable resources toward the design of newer, better methods of electric propulsion. This paper discusses the motives behind the electrification of heavy-duty vehicles, the state-of-the-art technology currently available on the market, and the novel application of silicon carbide to electric drive trains as a means of increasing their heat tolerance, …

New Force Transducer For Mitral Valve Chordae Tendinea, Joseph Berryman

Biomedical Engineering Undergraduate Honors Theses

In order to inform the future of mitral valve repair and replacement, more investigation into the mechanics of the sub-valvular structure is needed. Understanding the roles of each chord during valve closure requires a sensor capable of detecting these small forces with enough sensitivity to determine the characteristics of each of the chordal types. The focus of the cantilever force transducer is to maximize this sensitivity while also minimizing the invasiveness of the sensor on the overall function of the chord. The design utilizes flexible yet strong 3D printed resin and cantilever arms to improve the strain exerted on a …

Design And Assembly Of High-Temperature Signal Conditioning System On Ltcc With Silicon Carbide Cmos Circuits, Sajib Roy

Graduate Theses and Dissertations

The objective of the work described in this dissertation paper is to develop a prototype electronic module on a low-temperature co-fired ceramic (LTCC) material. The electronic module would perform signal conditioning of sensor signals (thermocouples) operating under extreme conditions for applications like gas turbines to collect data on the health of the turbine blades during operation so that the turbines do not require shutdown for inspection to determine if maintenance is required. The collected data can indicate when such shutdowns, which cost $1M per day, should be scheduled and maintenance actually performed. The circuits for the signal conditioning system within …

Statistical Machine Learning For Breast Cancer Detection With Terahertz Imaging, Tanny Andrea Chavez Esparza

Graduate Theses and Dissertations

Breast conserving surgery (BCS) is a common breast cancer treatment option, in which the cancerous tissue is excised while leaving most of the healthy breast tissue intact. The lack of in-situ margin evaluation unfortunately results in a re-excision rate of 20-30% for this type of procedure. This study aims to design statistical and machine learning segmentation algorithms for the detection of breast cancer in BCS by using terahertz (THz) imaging. Given the material characterization properties of the non-ionizing radiation in the THz range, we intend to employ the responses from the THz system to identify healthy and cancerous breast tissue …

Characterization Of Gesn Semiconductors For Optoelectronic Devices, Hryhorii Stanchu

Graduate Theses and Dissertations

Germanium-tin alloys with Sn compositions higher than 8 at. % to 10 at. % have recently attracted significant interest as a group IV semiconductor that is ideal for active photonics on a Si substrate. The interest is due to the fact that while at a few percent of Sn, GeSn is an indirect bandgap semiconductor, at about 8 to 10 at. % Sn, GeSn transitions to a direct bandgap semiconductor. This is at first surprising since the solid solubility of Sn in Ge under equilibrium growth conditions is limited to only about 1 at. %. However, under non-equilibrium growth conditions, …

Analog Spiking Neural Network Implementing Spike Timing-Dependent Plasticity On 65 Nm Cmos, Luke Vincent

Graduate Theses and Dissertations

Machine learning is a rapidly accelerating tool and technology used for countless applications in the modern world. There are many digital algorithms to deploy a machine learning program, but the most advanced and well-known algorithm is the artificial neural network (ANN). While ANNs demonstrate impressive reinforcement learning behaviors, they require large power consumption to operate. Therefore, an analog spiking neural network (SNN) implementing spike timing-dependent plasticity is proposed, developed, and tested to demonstrate equivalent learning abilities with fractional power consumption compared to its digital adversary.

Improvement Of Stability Of A Grid-Connected Inverter With An Lcl Filter By Robust Strong Active Damping And Model Predictive Control, Seungyong Lee

Graduate Theses and Dissertations

This study addresses development and implementation of robust control methods for a three-phase grid-connected voltage source inverter (VSI) accompanied by an inductive-capacitive-inductive (LCL) filter. A challenge of current control for the VSI is LCL filter resonance near to the control stability boundary, which interacts with the inverter control switching actions and creates the possibility of instability. In general, active damping is needed to stabilize the system and ensure robust performance in steady-state and dynamic responses. While many active damping methods have been proposed to resolve this issue, capacitor-current-feedback active damping has been most widely used for its simple implementation.

There …

An Accurate And Efficient Electro-Thermal Compact Model Of Sic Power Mosfet Including Third Quadrant Behavior, Arman Ur Rashid

Graduate Theses and Dissertations

Due to narrower bandgap and lower critical electric field, silicon (Si) power devices have reached their limit in terms of the maximum blocking voltage capability. Exploiting this limitation, wide bandgap devices, namely silicon carbide (SiC) and gallium nitride (GaN) devices, are increasingly encroaching on the lucrative power electronics market. Unlike GaN, SiC devices can exploit most of the established fabrication techniques of Si power devices. Having substrate of the same material, vertical device structures with higher breakdown capabilities are feasible in SiC, unlike their GaN counterpart. Also, the excellent thermal conductivity of SiC, compared to GaN and Si, let SiC …