Electrical and Computer Engineering Commons^™

Analysis Of An Isolated Bidirectional Ćuk Converter, Yeny Hau Chen

Graduate Theses and Dissertations

The objective of this thesis is to perform an analysis of the isolated bidirectional Ćuk dc-dc converter topology and demonstrate the advantages and operation of this configuration through simulations using MATLAB/SimulinkTM and measurements collected from a 1.5-kW prototype tested at the Engineering Research Center (ENRC) laboratory of the University of Arkansas. The idea of integrating an active-clamp snubber circuit on each side of the converter, proposed by Dr. Sudip Mazumder from the University of Illinois, Chicago, limits the additional voltage stresses on the components due to the energy from the transformer’s leakage inductance. This is studied in this thesis to …

Development Of Medical Device For Volume Status Assessment Using Peripheral Venous Pressure, Audra Beneux

Graduate Theses and Dissertations

The severe side effects of acute dehydration and blood loss may be prevented if assessed and treated quickly. As amplifier technology has improved, small peripheral venous pressure (PVP) signals collected using a transducer on an intravenous catheter can be analyzed to monitor patient volume status. This thesis details the development of an embedded system prototype that quickly and accurately assesses volume status using PVP analysis. The volume prediction algorithm classified 10 seconds of PVP data as “dehydrated” or “resuscitated”. The hardware design consisted of four primary areas: analog signal conditioning, processing, user interaction, and power. After data collection, the signal …

The Wideband Tunability Of Double Gunn Diodes, Latarence Butts, Samir M. El-Ghazaly

Electrical Engineering Faculty Publications and Presentations

Gunn diodes use the Ridley–Watkins–Hilsum effect to generate low noise millimeter wave signals for communication and sensing applications. However, Monte Carlo calculations indicate that the velocity–field characteristics of compensated GaAs contain a second peak due to phonon scattering. A novel device that leverages this double Ridley–Watkins–Hilsum effect to achieve ultra-wideband tunability of low-noise millimeter waves is proposed in this article. The second region of negative differential mobility is gradually introduced in seven mobility profiles, which are each simulated in eight device lengths. It is found that a 2.5 μm Gunn diode with a compensation ratio of 0.6 operating at …

Experimental And Computational Analysis Of Broadband Thz Photoconductive Antennas, Zachary Uttley, Jose Santos Batista, Bilal Pirzada, Magda El-Shenawee

Electrical Engineering Faculty Publications and Presentations

The work presents the fabrication and measurements of four LT-GaAs photoconductive terahertz (THz) antennas with different geometries of metallic electrodes. The goal is to analyze the overall bandwidth of the antennas through a comparison between the spectra of the generated photocurrent in the antenna gap, the radiated electric field THz pulse, and the S₁₁ parameter of the metallic electrodes. The photocurrent density and the S₁₁ parameters are computed using COMSOL multiphysics, while the generated THz pulse was experimentally measured using a time-domain spectroscopy system. The polarizations of the photoconductive antennas are experimentally measured, using x-cut quartz crystal halfwave …

A Partial Discharge Inception Voltage Modeling Approach, Shilpi Mukherjee, Tristan Mark Evans, David Huitink, H. Alan Mantooth

Electrical Engineering Faculty Publications and Presentations

A partial discharge inception voltage modeling approach promoting design-for-reliability considerations in advanced power modules is presented. As power modules are being operated at higher voltages and become more compact to meet power density demands, there is an increased risk of partial discharge, the silent precursor to electrical breakdown that degrades insulation material. The trade-off between voltage class and module compaction must be quantified. This work presents a methodology to model the tradeoff for any substrate and encapsulant material. A surface charge density-based partial discharge inception voltage (PDIV) model was developed to overcome the challenges in electric field-based models. The model …

Effects Of Electrodes Layout On Performance Of Millimeter-Wave Transistors, Soheil Nouri, Samir M. El-Ghazaly

Electrical Engineering Faculty Publications and Presentations

This work presents a systematic parameter extraction methodology for modeling of millimeter-wave transistors. The physics-based parameter extraction approach in this study is included in the wave-electron-transport model to improve the accuracy of the simulation results. The effects of extrinsic parameters on the performance of the device are also analyzed in detail. Skin effects and sharp metallization edge effects as the two physical phenomena that impact the current distribution and the resistance of millimeter-wave transistors are studied thoroughly. Two common electrode layout variations, the T configuration and the fork configuration, are compared. The comparison mainly targeted their performance on upper millimeter …

Detection And Localization Of Data Forgery Attacks In Automatic Generation Control, Fengli Zhang, Yatish R. Dubasi, Wei Bao, Qinghua Li

Electrical Engineering Faculty Publications and Presentations

Automatic Generation Control (AGC) is a key control system to maintain the power system’s balance between load and supply by maintaining its frequency in a specific range. It collects the tie-line power flow and frequency measurements of each control area to calculate the Area Control Error (ACE) and then adjusts power generation based on the calculated ACE. However, malicious frequency or tie-line power flow measurements can be injected and then AGC is misled to make false power generation adjustments which will harm power system operations. Such attacks can be carefully designed to pass the power system’s existing bad data detection …

Using Molecular Dynamics Simulations To Decipher Mechanistic Details Of Biomolecular Processes Of Biology And Biotechnology Oriented Applications, Adithya Polasa

Graduate Theses and Dissertations

Researchers in chemistry and biology often utilize computer simulations, in conjunction with experimental data, to model and predict the structures, energies, kinetics, processes, and functions of the systems that are their focus of study, ranging from single molecules to whole viruses. Here, we use molecular dynamics (MD) techniques to gain a deeper understanding of biomolecular processes in biology and biotechnology-oriented applications. Using a mixture of equilibrium and non-equilibrium MD simulations, this work describes the insertion process of YidC at the atomic level. In order to better comprehend the insertion process, several docking models of YidC-Pf3 in the lipid bilayer were …

Improved Compact Modeling Of High Voltage Gallium Nitride High Electron Mobility Transistors, Md Maksudul Hossain

Graduate Theses and Dissertations

Since power converters shape a wide range of power electronic applications, the 'heart' of these conversions, such as solid-state switches, is crucial for achieving higher power density, lower loss, and higher efficiency operations. Although the limitations imposed by silicon-based power devices have been reduced by introducing novel devices such as IGBTs and super junction MOSFETs to allow for broader applications, solutions beyond silicon have presented a continuous challenge to the device engineers. Driving these converters at a higher switching frequency allows for higher power density. However, to support a higher frequency and operating temperature, superior materials, e.g., wide bandgap materials, …

Gate-Controlled Quantum Dots In Two-Dimensional Tungsten Diselenide And One-Dimensional Tellurium Nanowires, Shiva Davari Dolatabadi

Graduate Theses and Dissertations

This work focuses on the investigation of gate-defined quantum dots in two-dimensional transition metal dichalcogenide tungsten diselenide (WSe2) as a means to unravel mesoscopic physical phenomena such as valley-contrasting physics in WSe2 flakes and its potential application as qubit, as well as realizing gate-controlled quantum dots based on elementaltellurium nanostructures which may unlock the topological nature of the host material carriers such as Weyl states in tellurium nanowires.The fabrication and characterization of gate-defined hole quantum dots in monolayer and bilayer WSe2 are reported. The gate electrodes in the device design are located above and below the WSe2 nanoflakes to accumulate …

Design And Comparison Of Asynchronous Fft Implementations, Julie Bigot

Graduate Theses and Dissertations

Fast Fourier Transform (FFT) is a widely used digital signal processing technology in a large variety of applications. For battery-powered embedded systems incorporating FFT, its physical implementation is constrained by strict power consumption, especially during idle periods. Compared to the prevailing clocked synchronous counterpart, quasi-delay insensitive asynchronous circuits offer a series of advantages including flexible timing requirement and lower leakage power, making them ideal choices for these systems. In this thesis work, various FFT configurations were implemented in the low-power Multi-Threshold NULL Convention Logic (MTNCL) paradigm. Analysis illustrates the area and power consumption trends along the changing of the number …

Data-Driven Deep Learning-Based Analysis On Thz Imaging, Haoyan Liu

Graduate Theses and Dissertations

Breast cancer affects about 12.5% of women population in the United States. Surgical operations are often needed post diagnosis. Breast conserving surgery can help remove malignant tumors while maximizing the remaining healthy tissues. Due to lacking effective real-time tumor analysis tools and a unified operation standard, re-excision rate could be higher than 30% among breast conserving surgery patients. This results in significant physical, physiological, and financial burdens to those patients. This work designs deep learning-based segmentation algorithms that detect tissue type in excised tissues using pulsed THz technology. This work evaluates the algorithms for tissue type classification task among freshly …

Electrical Modeling For Dynamic Performance Prediction And Optimization Of Mcpms Layout, Quang Minh Le

Graduate Theses and Dissertations

In recent years, the fast development of Multichip Power Modules (MCPM) packaging and Wide Bandgap (WBG) technology has enabled higher voltage and current ratings, better thermal performance, lower parasitic parameters, and higher mechanical reliability. However, the design of the MCPM layout is a multidisciplinary problem leading to many time-consuming analyses and tedious design processes. Because of these challenges, the design automation tool for MCPM layout has become an emerging research area and gained much attention from the power electronics community. The two critical objectives of a design automation tool for MCPM layout are fast and accurate models for design insights …

Hybrid Multilevel Converters With Internal Cascaded/Paralleled Structures For Mv Electric Aircraft Applications, Fei Diao

Graduate Theses and Dissertations

Using on-board medium voltage (MV) dc distribution system has been a megatrend for next-generation electric aircraft systems due to its ability to enable a significant system mass reduction. In addition, it makes electric propulsion more feasible using MV power electronic converters. To develop high-performance high-density MV power converters, the emerging silicon carbide (SiC) devices are more attractive than their silicon (Si) counterparts, since the fast switch frequency brought by the SiC can effectively reduce the volume and weight of the filter components and thus increase the converter power density. From the converter topology perspective, with the MV dc distribution, the …

Fiber-Based Time-Correlated Single Photon Counting As A Method For Investigating Metabolism During Tetanic Contraction Of Skeletal Muscle, Kathryn Miller Priest

Graduate Theses and Dissertations

Nicotinamide adenine dinucleotide (NAD) is a cofactor that serves to shuttle electrons during metabolic processes such as glycolysis, the tricarboxylic acid cycle, and oxidative phosphorylation (OXPHOS) [1-5]. The reduced form of NAD, NADH, is autofluorescent, making it a measurable characteristic in the investigation of metabolic changes. The fluorescence lifetime of NADH is dependent on the state of protein binding, specifically free or bound NADH, allowing for detection of metabolic shifts between glycolysis (free NADH) and OXPHOS (bound NADH) [6-16]. Fiber-coupled time-correlated single photon counting (TCSPC) equipped with an implantable needle probe can be used to measure NADH lifetime in vivo …

Reliability Enhancing Control Algorithms For Two-Stage Grid-Tied Inverters, Yuheng Wu

Graduate Theses and Dissertations

In the photovoltaic (PV) generation system, two types of grid-tied inverter systems are usually deployed: the single-stage grid-tied inverter system and the two-stage grid-tied inverter system. In the single-stage grid-tied inverter system, the input of the inverter is directly connected to the PV arrays, while an additional dc-dc stage is inserted between the PV arrays and the dc-ac inverter in the two-stage design. The additional dc-dc stage could provide a stable dc-link voltage to the inverter, which also enables new design possibilities, including the multi-MPPT operation and solar-plus-storage application. Thus, the two-stage grid-tied inverter has been widely used in the …

Modeling Of Temperature Dependence Of Λ-Graded Ingan Solar Cells For Both Strained And Relaxed Features, Mirsaeid Sarollahi, Mohammad Zamani-Alavijeh, Manal Abdullah Aldawsari, Rohith Allaparthi, Md Helal Uddin Maruf, Malak Refaei, Reem E. Alhelais, Yuriy I. Mazur, Morgan E. Ware

Electrical Engineering Faculty Publications and Presentations

The temperature dependence of Λ-graded InGaN solar cells is studied through simulation using nextnano software. Λ-Graded structures have been designed by increasing and then decreasing the indium composition in epitaxial InGaN layers. Due to polarization doping, layers of p-type and n-type doping arise without the need for impurity doping. Different individual structures are designed by varying the indium alloy profile from GaN to maximum indium concentrations, x_max , ranging from 20% to 90% pseudomorphically strained to a GaN substrate and from 20% to 100% for completely strain-relaxed materials and linearly decreases back to GaN. For In_xGa_{1-x …}

Constraint-Aware, Scalable, And Efficient Algorithms For Multi-Chip Power Module Layout Optimization, Imam Al Razi

Graduate Theses and Dissertations

Moving towards an electrified world requires ultra high-density power converters. Electric vehicles, electrified aerospace, data centers, etc. are just a few fields among wide application areas of power electronic systems, where high-density power converters are essential. As a critical part of these power converters, power semiconductor modules and their layout optimization has been identified as a crucial step in achieving the maximum performance and density for wide bandgap technologies (i.e., GaN and SiC). New packaging technologies are also introduced to produce reliable and efficient multichip power module (MCPM) designs to push the current limits. The complexity of the emerging MCPM …

A Memory-Centric Customizable Domain-Specific Fpga Overlay For Accelerating Machine Learning Applications, Atiyehsadat Panahi

Graduate Theses and Dissertations

Low latency inferencing is of paramount importance to a wide range of real time and userfacing Machine Learning (ML) applications. Field Programmable Gate Arrays (FPGAs) offer unique advantages in delivering low latency as well as energy efficient accelertors for low latency inferencing. Unfortunately, creating machine learning accelerators in FPGAs is not easy, requiring the use of vendor specific CAD tools and low level digital and hardware microarchitecture design knowledge that the majority of ML researchers do not possess. The continued refinement of High Level Synthesis (HLS) tools can reduce but not eliminate the need for hardware-specific design knowledge. The designs …

Etching Process Development For Sic Cmos, Weston Reed Renfrow

Graduate Theses and Dissertations

Silicon Carbide (SiC) is an exciting material that is growing in popularity for having qualities that make it a helpful semiconductor in extreme environments where silicon devices fail. The development of a SiC CMOS is in its infancy. There are many improvements that need to be made to develop this technology further. Photolithography is the most significant bottleneck in the etching process; it was studied and improved upon. Etching SiC can be a challenge with its reinforced crystal structure. Chlorine-based inductively coupled plasma (ICP) etching of intrinsic SiC and doped SiC, SiO2, and Silicon has been studied. A baseline chlorine …

Study Of Single-Photon Wave-Packets With Atomically Thin Nonlinear Mirrors, Christopher Klenke

Graduate Theses and Dissertations

A novel controlled phase gate for photonic quantum computing is proposed by exploiting the powerful nonlinear optical responses of atomically thin transition metal dichalcogenides (TMDs) and it is shown that such a gate could elicit a π-rad phase shift in the outgoing electric field only in the case of two incident photons and no other cases. Firstly, the motivation for such a gate is developed and then the implementation of monolayer TMDs is presented as a solution to previous realization challenges. The single-mode case of incident photons upon a TMD is derived and is then used to constrain the more …

Evaluation Of Single Phase Smart Pv Inverter Functions In Unbalanced Residential Distribution Systems, Darren Symonette

Graduate Theses and Dissertations

In the United States, smart PV inverters integrated with residential distribution systems are becoming a more common occurrence. With integration of smart PV inverters, power utilities are experiencing an increase of number of operations with regards to switched capacitor banks, voltage regulators and on load tap changers. These increases can lead to excess wear and tear on the devices causing power utilities to perform unwanted replacement and maintenance. However, smart PV inverters when controlled under specific functions can enable these inverters to provide reactive power and voltage control which in turn lowers the number of operations for switched capacitor banks, …

Materials Design For Energy Applications Using Ab- Initio Calculations, Hind Hemaidee Alqurashi

Graduate Theses and Dissertations

The structural, dynamical, electronic, and thermoelectric properties of rock-salt and wurtzite Cd1-xZnxO alloys, VTiRhZ (Al, Ga, In, Si, Ge, Sn) and ZrTiRhZ (Ge, Sn) quaternary Heusler alloys (QHAs) were investigated using density functional theory (DFT) and semi-classical Boltzmann transport theory. From these calculations, the alloys were identified as potential materials for future thermoelectric applications. Furthermore, the magnetic and spin-polarization properties of these QHAs were investigated. The total magnetic moments were found to be integer values for all QHAs. In addition, all studied QHAs except VTiRhAl possess a half-metallic behavior with a 100% spin-polarization. The half-metallic ferromagnetic behavior makes them promising …

Controller Platform Design And Demonstration For An Electric Aircraft Propulsion Driv, Rosten Sweeting

Graduate Theses and Dissertations

With the growth in the aerospace industry there has been a trend to optimize the performance of an aircraft by reducing fuel consumption and operational cost. Recent advancements in the field of power electronics have pushed towards the concepts of hybrid electric aircraft also known as more electrical aircrafts. In this work, a custom controller board for an electric aircraft propulsion drive was designed to drive a permanent magnet synchronous motor. Design of the controller board required knowledge of the topology selection and power module selections. Simulations of the system were performed using MATLAB/Simulink to analyze the overall performance of …

Study Of Thin Gan/Ingan/Gan Double Graded Structures For Future Photovoltaic Application, Mirsaeid Sarollahi

Graduate Theses and Dissertations

Indium gallium nitride (In_x Ga_(1-x) N) materials have displayed great potential for photovoltaic and optoelectronic devices due to their optical and electrical properties. Properties such as direct bandgap, strong bandgap absorption, thermal stability and high radiation resistance qualify them as great materials for photovoltaic devices. The tunable bandgap which absorbs the whole solar spectrum is the most significant feature which became attractive for scientists. The bandgap for these materials varies from 0.7 eV for InN to 3.4 eV for GaN covering from infrared to ultraviolet. In_x Ga_(1-x) N wurtzite crystal is grown on GaN buffer layer by Molecular Beam Epitaxy …

Development Of Ltcc-Packaged Optocouplers As Optical Galvanic Isolation For High-Temperature Applications, Pengyu Lai, David Gonzalez, Syam Madhusoodhanan, Abbas Sabbar, Salahaldein Ali Aboajila Ahmed, Binzhong Dong, Jiangbo Wang, H. Alan Mantooth, Shui-Qing Yu, Zhong Chen

Electrical Engineering Faculty Publications and Presentations

This paper reports high-temperature optocouplers for signal galvanic isolation. Low temperature co-fired ceramic (LTCC) technology was used in the design and fabrication of the high-temperature optocoupler package. The optimal coupling behaviors, driving capabilities and response speed of the optocouplers were concentrated and investigated in this paper. Emitters and detectors with different emission and spectral wavelengths were studied to achieve optimal coupling behaviors. Relatively high coupling efficiency is achieved with emitters and detectors of emission and spectral wavelength in the red spectrum (i.e., 620–750 nm), leading to higher current transfer ratios (CTR). To further enhance the electrical performance, optocouplers with multiple …

Design Of A Bandgap Voltage Reference, Nicolaus Vail

Electrical Engineering Undergraduate Honors Theses

This thesis details the design process of a bandgap voltage reference (BGR) integrated circuit in a 180 nm CMOS process. A BGR provides a constant DC voltage across a range of operating temperatures and supply voltages. By its nature, the circuit is intended as a reference, not to provide current, so the output would be connected to a very high impedance, such as the gate of a transistor. At 27°C, this design provides a 955 mV reference voltage given a nominal VDD of 3 V. From 20°C to 175°C, the output voltage has a variance of 7.2 mV (approximately 0.8%) …

Signal Analysis Of Photovoltaic Systems For Multilevel Cybersecurity, Wesley G. Schwartz

Electrical Engineering Undergraduate Honors Theses

The cybersecurity of grid-connected power electronics is a rapidly developing field as more and more of these devices become a part of the Internet of Things. The objective of this thesis to analyze the current control signals of a photovoltaic (PV) inverter and develop an interface board for the implementation of a new cyber-secure controller.

In this thesis, the testing and in-depth analysis of the current PV inverter control system will be conducted. Using the data collected, an interface board will be developed to allow the use of the Unified Control Board (UCB), developed by Chris Farnell, in the PV …

Junction Temperature Estimation Of Silicon Carbide Power Module Using Internal Gate Resistance As Temperature Sensitive Electrical Parameter, Michael Sykes

Graduate Theses and Dissertations

The junction temperature of a power module is measured non-intrusively and uninterrupted in its application by analyzing the dependency of gate resistance to temperature. The circuit configuration proposed consists of altering the gate loop path and adding a basic peak detection circuit with an added low-pass filter to accurately measure the small differences seen during a temperature change on the internal gate resistance. The testing on this Silicon Carbide power module shows that the internal gate resistance has a positive temperature coefficient. This causes the current and the voltage drop on the gate loop sensing resistance to reduce as the …

High Power Density And High Efficiency Converter Topologies For Renewable Energy Conversion And Ev Applications, Dereje Lemma Woldegiorgis

Graduate Theses and Dissertations

This dissertation work presents two novel converter topologies (a three-level ANPC inverter utilizing hybrid Si/SiC switches and an Asymmetric Alternate Arm Converter (AAAC) topology) that are suitable for high efficiency and high-power density energy conversion systems. The operation principle, modulation, and control strategy of these newly introduced converter topologies are presented in detail supported by simulation and experimental results. A thorough design optimization of these converter topologies (Si/SiC current rating ratio optimization and gate control strategies for the three-level ANPC inverter topology and component sizing for the asymmetric alternate arm converter topology) are also presented.

Performance comparison of the proposed …