Electrical and Computer Engineering Commons^™

Integrated Optical Transmitters And Receivers Using Multi-Segment Laser Processes, J. G. Wasserbauer, Dennis J. Derickson, K. Giboney, R. J. Helkey, J. R. Karin, A. Mar, J. E. Bowers

Electrical Engineering

No abstract provided.

Electroluminescence And Electrical Transport In Poly(3-Octylthiophene) Diodes, David Braun, G. Gustafsson, D. Mcbranch, A. J. Heeger

Electrical Engineering

We report visible light emission from diodes made from poly(3-octylthiophene). Use of a soluble derivative of polythiophene allows fabrication of the light emitting diodes by casting the polymer film from solution with no subsequent processing or heat treatment required. The devices emit dim red-orange light with relatively low external quantum efficiencies, below 2.5×10⁻⁵ photons per electron at room temperature. Electrical characterization reveals diode behavior with rectification ratios greater than 10². The temperature dependence indicates that tunneling phenomena dominate the charge injection.

Microwave And Millimeter Wave Signal Generation Using Mode-Locked Semiconductor Lasers With Intra-Waveguide Saturable Absorbers, Dennis J. Derickson, R. J. Helkey, A. Mar, J. G. Wasserbauer, Y. G. Wey, J. E. Bowers

Electrical Engineering

Microwave and millimeter wave signals can be generated using mode-locked semiconductor lasers with intra-waveguide saturable absorbers. Monolithic and external cavity devices optimized for electrical and optical signal generation are discussed along with measurements of amplitude noise, phase noise, output power, and repetition rate tunability.

Suppression Of Multiple Pulse Formation In External-Cavity Mode-Locked Semiconductor Lasers Using Intrawaveguide Saturable Absorbers, Dennis J. Derickson, R. J. Helkey, A. Mar, Judy R. Karin, J. E. Bowers, R. L. Thornton

Electrical Engineering

Imperfect antireflection coatings in external-cavity mode-locked semiconductor lasers can cause multiple output pulse generation. The incorporation of an intrawaveguide saturable absorber segment into the laser suppresses this problem. Single pulse outputs of less than 2.8 ps and 0.7 pJ of energy are obtained using such devices with both quantum well and bulk active regions

Comparison Of Timing Jitter In External And Monolithic Cavity Mode-Locked Semiconductor Lasers, Dennis J. Derickson, P. A. Morton, J. E. Bowers, R. L. Thornton

Electrical Engineering

A comprehensive timing jitter comparison is made for mode-locked semiconductor lasers using active, passive, and hybrid mode-locking techniques in both external and monolithic cavity configurations. Active mode locking gives the lowest residual rms timing jitter of 65 fs (150 Hz-50 MHz), followed by the hybrid and passive mode-locking techniques. It is found that monolithic cavity devices with all active waveguides have higher timing jitter levels than the comparable external cavity case.

Improved Efficiency In Semiconducting Polymer Light-Emitting Diodes, David Braun, A. J. Heeger, H. Kromer

Electrical Engineering

We report visible light emission from metal-polymer diodes made from semiconducting polymers, with indium-tin oxide as the “ohmic” contact, and a variety of metals as the barrier metal. Our results, which confirm the discovery by the Cambridge group [Nature347, 539 (1990)], demonstrate that light-emitting diodes can be fabricated by casting the polymer film on indium-tin oxide from solution with no subsequent polymer processing or heat treatment required. Electrical characterization reveals diode behavior with rectification ratios greater than 105 at sufficiently high voltages. Use of an electrode material with low work function leads to more than an order of magnitude improvement …

Efficient Single-Heterojunction Al0.27Ga0.73As/Gaas P-I-N Photodiodes With 22-Ghz Bandwidths, C. Johnson, S. Sloan, D. M. Braun, J. L. Russell, M. Zurakowski, M. Lightner, F. Kellert, G. Patterson, R. Koo, Dennis J. Derickson, J. E. Bowers

Electrical Engineering

A report is presented on the design, fabrication, testing, and modeling of single-heterojunction Al_0.27Ga_0.73As/Ga p-i-n photodiodes for use as components in optical receivers. The photodiodes are grown by molecular beam epitaxy and fabricated as 1100-μm² mesa structures. At 5-V reverse bias and 850 nm, 100 fF of capacitance, 90 pA of leakage current, 73% external quantum efficiency, <2% reflectivity, and 22-GHz bandwidths are typically measured.

High-Frequency Electrooptic Fabry-Perot Modulators, R. J. Simes, R. H. Yan, C. C. Barron, Dennis J. Derickson, D. G. Lishan, Judy R. Karin, L. A. Coldren, M. Rodwell, S. Elliott, B. Hughes

Electrical Engineering

Electrooptic modulators built from GaAs/Al_xGa_1-xAs Fabry-Perot cavities operating up to 6.5 GHz are reported. The measured frequency response agrees well with the one predicted using an equivalent circuit model derived from high-speed electrical measurements. The parasitic capacitances have been reduced to approximately 30 fF by fabricating the devices on semi-insulating GaAs substrates and integrating them with on-wafer bound pads which have dimensions compatible with microwave coplanar probes.

Visible Light Emission From Semiconducting Polymer Diodes, David Braun, A. J. Heeger

Electrical Engineering

We report visible light emission from Shottky diodes made from semiconducting polymers, confirming the discovery by the Cambridge group [Nature 347, 539 (1990)]. Our results demonstrate that light-emitting diodes can be fabricated by casting the polymer film from solution with no subsequent processing or heat treatment required. Electrical characterization reveals diode behavior with rectification ratios greater than 104. We propose that tunneling of electrons from the recitifying metal contact into the gap states of the positive polaron majority carriers dominates current flow and provides the mechanism for light emission.

Relative And Absolute Timing Jitter In Actively Mode-Locked Semiconductor Lasers, Dennis J. Derickson, A. Mar, J. E. Bowers

Electrical Engineering

No abstract provided.

Architecture For A Human-Robot Symbiotic System, Fred W. Depiero, Wayne W. Manges, Reid L. Kress, Mike R. Kedl, William R. Hamel

Electrical Engineering

This paper describes a human-robot symbiont that is under development at Oak Ridge National Laboratory. An overview of the symbiotic system is described that motivates the architecture that has been developed. The architecture is a hierarchical structure that consists of several expert systems which reside above a robot control interface. This interface allows the manipulator to be operated in both a teleoperated and autonomous mode. All these processes coexist with the lowest level of the hierarchy, which is a numerically intensive control algorithm. The architecture is implemented on five processors in a coarsely parallel system.

An Indirect Sensing Technique For Closed-Loop Diesel Fuel Quantity Control, Carl A. Maccarley, Walter D. Clark, Keay T. Nakae

Electrical Engineering

Despite significant advances in electronic control technology applied to diesel engines, commercially available injection systems for automotive diesel engines remain limited by the open-loop mapping of the injection pump. An initial calibration is relied upon to translate a fuel delivery command to an actual fuel quantity. In practice, however, these two variables may be substantially different due to the effects of mechanical wear, repair, and the wide range of operating conditions. Possible ramifications of this discrepancy are excessive exhaust smoke due to overfueling, increased fuel consumption, degraded driveability, and poor idle characteristics. The major obstacle to closing the fuel control …

Self-Mode-Locking Of A Semiconductor Laser Using Positive Feedback, Dennis J. Derickson, R. J. Helkey, A. Mar, P. A. Morton, J. E. Bowers

Electrical Engineering

A new mode-locking technique, self-mode-locking, is described which uses the detected optical pulses from the mode-locked laser as the active driving source. This technique forms narrow-width mode-locked optical pulses at low repetition rates without the use of a microwave synthesizer

Use Of Technology For Undergraduate Engineering Education, B. A. Black, J. S. Demetry, J. G. Harris, J. R. Jones

Electrical Engineering

California Polytechnic State University, Rose-Hulman Institute of Technology, University of Alabama at Birmingham, and Worcester Polytechnic Institute have formed a consortium to develop an alternative learning environment centered around a workstation comprised of a personal computer interfaced to a video disk and laboratory instrumentation. The first phase in their collective effort has involved the development of four instructional modules in the fundamentals of electrical engineering. The results of the first phase efforts are presented. They demonstrate how four different universities can work together to agree on standards, and to prepare instructional material that can be shared. The second phase will …

A 100-Khz - 22 Ghz Instrumentation Photoreceiver, Dennis J. Derickson, C. M. Miller, R. L. Van Tuyl

Electrical Engineering

A photoreceiver consisting of a high-speed p-i-n photodetector and a 100-kHz to 22-GHz distributed amplifier is described. Photoreceiver calibration is accomplished by optical heterodyne techniques. The photoreceiver is used with a microwave spectrum analyzer to produce a fully amplitude-calibrated 22-GHz-bandwidth lightwave signal analyzer system for displaying intensity-modulated light with -65-dB (optical) sensitivity at 1300-nm and 1550-nm wavelengths.

State-Feedback Control Of Non-Linear Systems, Stanislaw H. Żak, Carl A. Maccarley

Electrical Engineering

A design method for state-feedback controllers for single-input non-linear systems is proposed. The method makes use of the transformations of the non-linear system into ‘controllable-like’ canonical forms. The resulting non-linear state feedback is designed in such a way that the eigenvalues of the linearized closed-loop model are invariant with respect to any constant operating point. The method constitutes an alternative approach to the design methodology recently proposed by Baumann and Rugh. Also a review of different transformation methods for non-linear systems is presented. An example and simulation results of different control strategies are provided to illustrate the design technique.

Final Project Report: Development Of A Hydrogen Fueled Transit Vehicle, C. A. Maccarley

Electrical Engineering

No abstract provided.

Electronic Fuel Injection Techniques For Hydrogen Powered I.C. Engines, Art Maccarley, W. D. Van Vorst

Electrical Engineering

Numerous studies have demonstrated the advantages of hydrogen as a fuel for Otto Cycle engines due to high thermal efficiency and low exhaust pollutant levels. Characteristic of hydrogen engine operation using premixed intake charge formation is a problem of pre-ignition resulting in an intake manifold “backfire”. Additional problems include high NO_x production when using certain equivalence ratios and power output degradation due to low fuel energy/volume density.

Techniques for direct and port fuel injection are discussed as means for overcoming these problems. Emphasis is placed on the need for total engine control, integrating control of fuel injection, ignition timing, …

Electronic Fuel Injection Techniques For Hydrogen Fueled Internal Combustion Engines, Carl Arthur Maccarley

Electrical Engineering

Numerous studies have demonstrated the advantages of hydrogen as a fuel for Otto Cycle engines due to high thermal efficiency and low exhaust pollutant levels. Characteristic of hydrogen engine operation using pre-mixed intake charge formation is a problem of pre-ignition resulting in an intake manifold "backfire." Additional problems include high NO production when using certain equivalence ratios and power output degradation due to low fuel energy/volume density.

Techniques for direct and manifold fuel injection are discussed as means for overcoming these problems. Emphasis is placed on the need for total engine control, integrating control of fuel injection, ignition timing, intake …